Touch Panel PC AHP-1083 AHP-1083 Intel® Atom™ D2550 1.86 GHz Processor Touch Panel PC With 8.4” TFT LCD AHP-1083 Manual 2nd Ed.
Touch Panel PC AHP-1083 Copyright Notice This document is copyrighted, 2013. All rights are reserved. The original manufacturer reserves the right to make improvements to the products described in this manual at any time without notice. No part of this manual may be reproduced, copied, translated, or transmitted in any form or by any means without the prior written permission of the original manufacturer. Information provided in this manual is intended to be accurate and reliable.
Touch Panel PC AHP-1083 Acknowledgments All other products’ name or trademarks are properties of their respective owners. Award is a trademark of Award Software International, Inc. Intel®, and Atom™ are trademarks of Intel® Corporation. Microsoft Windows is a registered trademark of Microsoft Corp. IBM, PC/AT, PS/2, and VGA are trademarks of International Business Machines Corporation. ® All other product names or trademarks are properties of their respective owners.
Touch Panel PC AHP-1083 Packing List Before you begin operating your PC, please make sure that the following materials are enclosed: 1 AHP-1083 Touch Panel PC 1 Phoenix Terminal Block 1 Mounting bracket and screws 1 CD-ROM for manual (in PDF format) If any of these items should be missing or damaged, please contact your distributor or sales representative immediately.
Touch Panel PC AHP-1083 Safety & Warranty 1. Read these safety instructions carefully. 2. Keep this user's manual for later reference. 3. Disconnect this equipment from any AC outlet before cleaning. Do not use liquid or spray detergents for cleaning. Use a damp cloth. 4. For pluggable equipment, the power outlet must be installed near the equipment and must be easily accessible. 5. Keep this equipment away from humidity. 6. Put this equipment on a firm surface during installation.
Touch Panel PC AHP-1083 d. The equipment does not work well, or you cannot get it to work according to the user’s manual. e. The equipment has been dropped and damaged. f. The equipment has obvious signs of breakage. 15. DO NOT LEAVE THIS EQUIPMENT IN AN ENVIRONMENT WHERE THE STORAGE TEMPERATURE IS BELOW -20°C (-4°F) OR ABOVE 60°C (140°F). IT MAY DAMAGE THE EQUIPMENT. FCC This device complies with Part 15 FCC Rules.
Touch Panel PC AHP-1083 Below Table for China RoHS Requirements 产品中有毒有害物质或元素名称及含量 AAEON Panel PC/ Workstation 有毒有害物质或元素 部件名称 铅 汞 镉 六价铬 多溴联苯 多溴二苯醚 (Pb) (Hg) (Cd) (Cr(VI)) (PBB) (PBDE) × ○ ○ ○ ○ ○ × ○ ○ ○ ○ ○ × ○ ○ ○ ○ ○ × ○ ○ ○ ○ ○ 硬盘 × ○ ○ ○ ○ ○ 液晶模块 × ○ ○ ○ ○ ○ 光驱 × ○ ○ ○ ○ ○ 触控模块 × ○ ○ ○ ○ ○ 电源 × ○ ○ ○ ○ ○ 印刷电路板 及其电子组件 外部信号 连接器及线材 外壳 中央处理器 与内存 O：表示该有毒有害物质在该部件所有均质材料中的含量均在 SJ/T 11363-2006 标准规定的限量要求以下。 X：表示该有毒有害物质至少在该部件的某一均质材料中的含量超出 SJ/
Touch Panel PC AHP-1083 Contents Chapter 1 General Information 1.1 Introduction................................................................ 1-2 1.2 Specification .............................................................. 1-3 1.3 Dimension ................................................................. 1-6 Chapter 2 Hardware Installation 2.1 Panelmount Installation ............................................. 2-2 2.2 Clear CMOS (JP2) .................................................... 2-3 2.
Touch Panel PC AHP-1083 Chapter 1 General Information Chapter 1 General Information 1- 1
Touch Panel PC AHP-1083 1.1 Introduction The AHP-1083 operator panel is an Intel® Atom™ D2550 1.86 GHz processor computer that is designed to serve as a human machine interface (HMI). It is a PC-based system with 8.4" color TFT LCD display, onboard Ethernet controller, multi-COM port interfaces and an audio controller. With a built-in CFast socket, the AHP-1083 is as compact and user friendly as a multi-function computer.
Touch Panel PC AHP-1083 1.2 Specification System CPU Onboard Intel® Atom™ D2550 1.86 GHz Processor System Memory 204pin DDRIII 800/1066 SODIMM x 1, Max. 4GB, default 2GB LCD / CRT Controller Intel® NM10 Integrated I/O Port USB2.0 x 2 RS-232 x 1 RS-232/422/485 x 1 LAN x 2 VGA x 1 Power input x 1 Power button x 1 Storage Disk Drive CFast™ slot x 1 (Easy to swap); 2.5” SATA HDD bay x 1 (Anti-vibration 1G) Expansion Mini card x 1 OS Support Windows CE 6.
Touch Panel PC AHP-1083 Mechanical Construction Plastic front bezel and aluminum back chassis Mounting Panel/ VESA Dimension 16"(W) x 12.2"(H) x 2.67"(D) (407mm x 310.5mm x 67.9mm) Carton Size 20.67"(W) x 18.31"(H) x 9.1"(D) (4525mm x 465mm x 230mm) Net Weight 4.4 lb (2kg) Gross Weight 6.16 lb (2.
Touch Panel PC AHP-1083 LCD Display Type 8.4”, SVGA, 450 nits, LED backlight Max. Resolution 800x600 Max. Colors 262k Power Consumption 7.
Touch Panel PC AHP-1083 1.3 Dimension AHP-1083 UNITS:mm 245.0 Chapter 1 General Information 1- 6 67.9 1 7 5 .9 1 4 6 .0 1 83.0 VESA 75 237.
Touch Panel PC AHP-1083 Chapter 2 Hardware Installation Chapter 2 Quick Installation Guide 2-1
Touch Panel PC AHP-1083 2.1 Panelmount Installation The display panel can be mounted into the wall. You will need the screws along with the mounting brackets, which be packed in the accessory box. Follow the steps below: Step 1: Place the operator panel into the wall. Step 2: Place the mounting brackets and bore the screw on it. Step 3: Screw mounting kits to fix the operator panel.
Touch Panel PC AHP-1083 2.2 Clear CMOS (JP2) JP2 Function 1-2 Normal (Default) 2-3 Clear CMOS 2.3 COM2 RI/+5V/+12V Selection (JP3) JP3 Function 1-2 +12V 3-4 RI (Default) 5-6 +5V Note: Max. Current rating is 0.5A. 2.4 COM Port #2 (CN19) RS-232 Mode Pin Signal Pin Signal 1 DCDB 2 DSRB 3 RXB 4 RTSB 5 TXB 6 CTSB 7 DTRB 8 RIB / +5 Volt. / (+12 Volt.
Touch Panel PC AHP-1083 3 RXD+ 4 N/C 5 TXD+ 6 N/C 7 RXD- 8 N/C / +5 Volt. / (+12 Volt.) 9 Ground 10 N/C Pin Signal RS-485 Mode Pin Signal 1 TXD- 2 N/C 3 N/C 4 N/C 5 TXD+ 6 N/C 7 N/C 8 N/C / +5 Volt. / (+12 Volt.) 9 Ground 10 N/C 43 CRT_PLUG# 2.
Touch Panel PC AHP-1083 2.
Touch Panel PC AHP-1083 2.7 Hard Disk Drive Installation Step 1: Loose the eight M3 screws of the rear cover. Step 2: Loose the three specified M3 screws to get the Hard Disk Drive (HDD) bracket.
Touch Panel PC AHP-1083 Step 3: Insert the HDD to the HDD bracket Step 4: Fasten the four screws to fasten the HDD and the HDD bracket Chapter 2 Quick Installation Guide 2 - 7
Touch Panel PC Step 5: Connect the SATA cable to the HDD Chapter 2 Quick Installation Guide 2 - 8 AHP-1083
Touch Panel PC AHP-1083 Chapter 3 AMI BIOS Setup Chapter 3 AMI BIOS Setup 3-1
Touch Panel PC AHP-1083 3.1 Setup Menu Setup submenu: Main Options summary: (default setting) System Date Day MM:DD:YYYY Change the month, year and century. The ‘Day’ is changed automatically. System Time HH : MM : SS Change the clock of the system.
Touch Panel PC AHP-1083 Setup submenu: Advanced Options summary: (default setting) ACPI Settings System ACPI Parameters S5 RTC Wake Settings Support S5 RTC Wake Function CPU Configuration CPU Configuration Parameters SATA Configuration SATA Device Options Settings USB Configuration Chapter 3 AMI BIOS Setup 3-3
Touch Panel PC AHP-1083 USB Configuration Parameters Super IO Configuration IT8783 Super IO Configuration Parameters H/W Monitor Monitor hardware status ACPI Settings Options summary: (default setting) Suspend Disabled ACPI Sleep State S3 (Suspend to RAM) Select the ACPI state used for System Suspend Chapter 3 AMI BIOS Setup 3-4
Touch Panel PC AHP-1083 S5 RTC Wake Settings Options summary: (default setting) Wake system with Fixed Disabled Time Enabled Enable or disable System wake on alarm event. Wake up time is setting by following settings.
Touch Panel PC Wake up minute 0-59 Wake up second 0-59 Wake system with Disabled Dynamic Time Enabled AHP-1083 Enable or disable System wake on alarm event. Wake up time is current time + Increase minutes.
Touch Panel PC AHP-1083 Options summary: (default setting) Hyper-Threading Disabled Enabled CPU Hyper-Threading Technology support or not SATA Configuration Options summary: (default setting) SATA Controller(s) Enabled Disabled SATA Controller Enable/Disable SATA Mode IDE Chapter 3 AMI BIOS Setup 3-7
Touch Panel PC AHP-1083 AHCI Configure SATA controller operating as IDE/AHCI mode.
Touch Panel PC AHP-1083 Options summary: (default setting) Legacy USB Support Enabled Disabled Auto Enables BIOS Support for Legacy USB Support. When enabled, USB can be functional in legacy environment like DOS. AUTO option disables legacy support if no USB devices are connected. DISABLE option will keep USB devices available only for EFI application Device Name Auto (Emulation Type) Floppy Forced FDD Hard Disk CD-ROM If Auto.
Touch Panel PC AHP-1083 Super IO Configuration Options summary: (default setting) Serial Port x Configuration Set Parameters of Serial Port x Restore AC Power Loss Power off Power on Last State Set Power on after power fail function Chapter 3 AMI BIOS Setup 3-10
Touch Panel PC AHP-1083 Serial Port 2 Configuration Options summary: (default setting) Serial Port Disabled Enabled En/Disable specified serial port.
Touch Panel PC AHP-1083 Select a resource setting for Super IO device. COM2 Type Option RS232 RS422 RS485 Configure COM2 operated as RS232, RS422 or RS485.
Touch Panel PC AHP-1083 Setup submenu: Chipset Options summary: (default setting) Host Bridge Host Bridge Parameters South Bridge South Bridge Parameters Chapter 3 AMI BIOS Setup 3-13
Touch Panel PC AHP-1083 Host Bridge Options summary: (default setting) Intel IGD Configuration Enter to set Graphic Configuration Memory Information Show current memory information Chapter 3 AMI BIOS Setup 3-14
Touch Panel PC AHP-1083 Intel IGD Configuration Options summary: (default setting) Auto Disable IGD Disabled Enabled Auto disable IGD upon external GFX detected. IGFX – Boot Type VBIOS Default CRT st 1 LVDS Select the Video Device which will be activated during POST LCD Panel Type 800x600 18bit st Select 1 panel native resolution.
Touch Panel PC LVDS1 Backlight Control AHP-1083 PWM Inverted PWM Normal Backlight control setting LVDSx Backlight 100% Controller 75% 50% 25% 0% Adjust backlight brightness Control LVDSx Disabled Enabled Dis/Enable LVDSx Fixed Graphics Memory 128MB Size 256MB Configure Fixed Graphics Memory Size Chapter 3 AMI BIOS Setup 3-16
Touch Panel PC AHP-1083 South Bridge Options summary: (default setting) Power Mode ATX Type AT Type Select AT/ATX Power Mode TPT Devices Configure onboard TPT Devices PCI Express Port x Disabled Enabled Enable/Disable PCI Express Port 0 - 3 Chapter 3 AMI BIOS Setup 3-17
Touch Panel PC AHP-1083 TPT Devices Options summary: (default setting) R8111E #x Controller Disabled Enabld R8111E Enable/Disable Chapter 3 AMI BIOS Setup 3-18
Touch Panel PC AHP-1083 Boot Configuration Options summary: (default setting) Quiet Boot Disabled Enabled Enables or disables Quiet Boot option Launch 8111E PXE Disabled OpROM Enabled En/Disable PXE boot for onboard 8111E LAN Boot Option #X XXXX Drive BBS Priorities The order of boot priorities.
Touch Panel PC AHP-1083 BBS Priorities Options summary: (default setting) Boot Option #x Disabled Device name Sets the system boot order Chapter 3 AMI BIOS Setup 3-20
Touch Panel PC AHP-1083 Setup submenu: Security Options summary: (default setting) Administrator Password/ Not set User Password You can install a Supervisor password, and if you install a supervisor password, you can then install a user password. A user password does not provide access to many of the features in the Setup utility. Install the Password: Press Enter on this item, a dialog box appears which lets you enter a password. You can enter no more than six letters or numbers.
Touch Panel PC AHP-1083 required at boot time, or when the user enters the Setup utility. Removing the Password: Highlight this item and type in the current password. At the next dialog box press Enter to disable password protection.
Touch Panel PC AHP-1083 HDD Security Options summary: (default setting) Set User Password/ Not set Set Master Password You can install a Master and User password. Before booting to OS, HDD will be set to frozen state. On S3 resume HDD will be unlocked using the HDD Password we entered while system booting. Install the Password: Press Enter on this item, a dialog box appears which lets you enter a password. You can enter no more than six letters or numbers.
Touch Panel PC AHP-1083 required at boot time, or when the user enters the Setup utility. Removing the Password: Highlight this item and type in the current password. At the next dialog box press Enter to disable password protection.
Touch Panel PC AHP-1083 Setup submenu: Exit Options summary: (default setting) Save Changes and Reset Reset the system after saving the changes Discard Changes and Reset Reset system setup without saving any changes Restore Defaults Restore/Load Default values for all the setup options.
Touch Panel PC AHP-1083 Restore the User Defaults to all the setup options Chapter 3 AMI BIOS Setup 3-26
Touch Panel PC AHP-1083 Chapter 4 Driver Installation Chapter 4 Driver Installation 4 - 1
Touch Panel PC AHP-1083 The AHP-1083 comes with a CD-ROM that contains all drivers and utilities that meet your needs. Follow the sequence below to install the drivers: Step 1 – Install Chipset Driver Step 2 – Install VGA Driver Step 3 – Install LAN Driver Step 4 – Install AHCI Driver Step 5 – Install Touch Driver Step 6 – Install Serial Port Driver (Optional) Please read instructions below for further detailed installations.
Touch Panel PC AHP-1083 4.1 Installation: Insert the AHP-1083 CD-ROM into the CD-ROM Drive. And install the drivers from Step 1 to Step 6 in order. Step 1 – Install Chipset Driver 1. Click on the STEP1-CHIPSET folder and select the OS folder your system is 2. Double click on the Setup.exe file located in each OS folder 3. Follow the instructions that the window shows 4. The system will help you install the driver automatically Step 2 – Install VGA Driver For Windows® 7 1.
Touch Panel PC AHP-1083 2. Install IEMGD Double click on the IEMGDInstallCC.exe Select the configuration Follow the instructions that the window shows The system will help you install the driver automatically Due to AHP-1083 resolution is 800 x 600, please select GCV5-n2_800x600x18bit.
Touch Panel PC AHP-1083 Chapter 4 Driver Installation 4 - 5
Touch Panel PC AHP-1083 If you want to update driver, please uninstall driver first. Uninstall IEMGD 1. Double click on the IEMGDInstallCC.exe 2. Follow the instructions that the window shows 3. The system will help you uninstall the driver automatically Step 3 – Install LAN Driver 1. Click on the Step 3 - LAN folder and select the OS folder your system is 2. Double click on the Setup.exe file located in each OS folder 3. Follow the instructions that the window shows 4.
Touch Panel PC AHP-1083 folder 3. Follow the instructions that the window shows 4. The system will help you install the driver automatically Step 5 – Install Touch Driver 1. Click on the Step 5 - Touch folder and select the OS folder your system is 2. Double click on the Setup.exe file located in each OS folder 3. Follow the instructions that the window shows 4. The system will help you install the driver automatically Step 6 – Install Serial Port Driver (Optional) 1.
