Ad va n c e d S y s t e m Controller AIS-E1 AIS-E1 Advanced System Controller 3.5” HDD x 1, 2.5” HDD/SSD x 4 Slim ODD x 1 Gigabit Ethernet x 2 COM x 1, USB2.0 x 6 HD Audio Codec AIS-E1 Manual 1st Ed.
Ad va n c e d S y s t e m Controller AIS-E1 Copyright Notice This document is copyrighted, 2012. All rights are reserved. The original manufacturer reserves the right to make improvements to the products described in this manual at any time without notice. No part of this manual may be reproduced, copied, translated, or transmitted in any form or by any means without the prior written permission of the original manufacturer. Information provided in this manual is intended to be accurate and reliable.
Ad va n c e d S y s t e m Controller AIS-E1 Acknowledgments All other products’ name or trademarks are properties of their respective owners. AMI is a trademark of American Megatrends Inc. CompactFlash™ is a trademark of the Compact Flash Association. Intel®, CoreTM and Celeron® are trademarks of Intel® Corporation. Microsoft Windows® is a registered trademark of Microsoft Corp. ITE is a trademark of Integrated Technology Express, Inc.
Ad va n c e d S y s t e m Controller AIS-E1 Packing List Before you begin operating your PC, please make sure that the following materials are enclosed: 1 9761E10000 Gift Box 1 AIS-E1 1 DVD-ROM for manual (in PDF format) and drivers If any of these items should be missing or damaged, please contact your distributor or sales representative immediately.
Ad va n c e d S y s t e m Controller AIS-E1 Safety & Warranty 1. Read these safety instructions carefully. 2. Keep this user's manual for later reference. 3. Disconnect this equipment from any AC outlet before cleaning. Do not use liquid or spray detergents for cleaning. Use a damp cloth. 4. For pluggable equipment, the power outlet must be installed near the equipment and must be easily accessible. 5. Keep this equipment away from humidity. 6. Put this equipment on a firm surface during installation.
Ad va n c e d S y s t e m Controller AIS-E1 d. The equipment does not work well, or you cannot get it to work according to the user’s manual. e. The equipment has been dropped and damaged. f. The equipment has obvious signs of breakage. 15. DO NOT LEAVE THIS EQUIPMENT IN AN ENVIRONMENT WHERE THE STORAGE TEMPERATURE IS BELOW -20°C (-4°F) OR ABOVE 65°C (149°F). IT MAY DAMAGE THE EQUIPMENT. FCC This device complies with Part 15 FCC Rules.
Ad va n c e d S y s t e m Controller AIS-E1 Below Table for China RoHS Requirements 产品中有毒有害物质或元素名称及含量 AAEON Boxer/ Industrial System 有毒有害物质或元素 部件名称 铅 汞 镉 六价铬 多溴联苯 多溴二苯醚 (Pb) (Hg) (Cd) (Cr(VI)) (PBB) (PBDE) × ○ ○ ○ ○ ○ × ○ ○ ○ ○ ○ × ○ ○ ○ ○ ○ × ○ ○ ○ ○ ○ 硬盘 × ○ ○ ○ ○ ○ 电源 × ○ ○ ○ ○ ○ 印刷电路板 及其电子组件 外部信号 连接器及线材 外壳 中央处理器 与内存 O：表示该有毒有害物质在该部件所有均质材料中的含量均在 SJ/T 11363-2006 标准规定的限量要求以下。 X：表示该有毒有害物质至少在该部件的某一均质材料中的含量超出 SJ/T 11363-2006 标准规定的限量要求。 备注： 一、此产品所标示之环保使用期限，系指在
Ad va n c e d S y s t e m Controller AIS-E1 Contents Chapter 1 General Information 1.1 Introduction................................................................ 1-2 1.2 Features .................................................................... 1-3 1.3 Specifications ............................................................ 1-4 Chapter 2 Hardware Installation 2.1 Location of Connectors (Main Board) ....................... 2-2 2.2 Mechanical Drawing of AIS-E1 ................................
Ad va n c e d S y s t e m Controller Chapter 3 AIS-E1 AMI BIOS Setup 3.1 System Test and Initialization. .................................. 3-2 3.2 AMI BIOS Setup ........................................................ 3-3 Chapter 4 Driver Installation 4.1 Installation ................................................................. 4-3 Appendix A Programming The Watchdog Timer A.1 Programming ........................................................A-2 A.2 ITE8728 Watchdog Timer Initial Program ..
Ad va n c e d S y s t e m Controller AIS-E1 Chapter 1 General Information Chapter 1 General Information 1- 1
Ad va n c e d S y s t e m Controller AIS-E1 1.1 Introduction AIS-E1 adopts the Intel® CoreTM i7/ i5/ Celeron® QC/DC Processor up to 45W. The chipset is equipped with Intel® QM67. Moreover, the system memory features two DDR3 1066/1333/1600 MHz SODIMM up to 16 GB. It deploys two LAN ports that consist of 10/100/1000Base-TX Ethernet RJ-45 ports. AIS-E1 condensed appearance features desktop and wallmount form factor that fits nicely into a space-limited environment. This AIS-E1 supports up to one 3.
Ad va n c e d S y s t e m Controller AIS-E1 1.2 Features Mini-ITX Based Chassis with scalable expansion slots. Socket G2 (rPGA988B) 2nd Generation for Intel® Core™ i7 / i5 / Celeron® QC / DC processors up to 45W Max 2 x 204-pin Dual-channel DDR3 1066/1333/1600 MHz SODIMM up to 16GB Intel® Integrated Graphics Engine supports Dual View by VGA, DVI, HDMI, LVDS LAN 1 : Intel® 82579 PHY Gigabit Ethernet LAN 2 : Realtek RTL 8111E Gigabit Ethernet Up to 2.5” HDD/SSD x 4 or up to 2.
Ad va n c e d S y s t e m Controller AIS-E1 1.3 Specifications CPU Socket G2 (rPGA988B) 2nd Generation for Intel® Core™ i7 / i5 / Celeron® QC / DC processors up to 45W Chipset Intel® QM67 System Memory 204-pin Dual Channel DDR3 1066/1333/1600 MHz SODIMM x2, up to 16GB Display Interface Storage Device Network Front I/O Rear I/O VGA DB-15 x 1 DVI DVI-D x 1 Others HDMI x 1 SSD CFast x 1 HDD 2.
Ad va n c e d S y s t e m Controller Expansion Indicator AIS-E1 Mini Card Mini Card x 1 Others PCI-Express [x4] Front PWR, HDD Power Requirement 12V DC-in System Cooling CPU cooler x 1 System Cooler x 1 Mounting Wallmount Operating Temperature 32°F ~ 113°F (0°C ~ 45°C) Storage Temperature -40°F ~ 176°F (-40°C ~ 80°C) Anti-Vibration 0.5g rms / 5 ~ 500Hz / operation – HDD 3.5g rms / 5~ 500Hz / operation – SSD Anti-Shock 10 G peak acceleration (11 msec.
Ad va n c e d S y s t e m Controller AIS-E1 Chapter 2 Hardware Installation Chapter 2 Hardware Installation 2-1
Ad va n c e d S y s t e m Controller 2.
Ad va n c e d S y s t e m Controller AIS-E1 Solder Side Chapter 2 Hardware Installation 2-3
Ad va n c e d S y s t e m Controller 2.
Ad va n c e d S y s t e m Controller AIS-E1 2.3 List of Jumpers The board has a number of jumpers that allow you to configure your system to suit your application. The table below shows the function of each of the board's jumpers: Label Function JP1 Clear CMOS JP3 Auto Power Button JP6 +12V/+5V/RING Selection JP7 Inverter Power Selection 2.4 List of Connectors The board has a number of connectors that allow you to configure your system to suit your application.
Ad va n c e d S y s t e m Controller AIS-E1 COM1, COM3 ~ COM5 RS-232 Connector SATA1~SATA2 SATA 3.
Ad va n c e d S y s t e m Controller AIS-E1 2.5 Setting Jumpers You configure your card to match the needs of your application by setting jumpers. A jumper is the simplest kind of electric switch. It consists of two metal pins and a small metal clip (often protected by a plastic cover) that slides over the pins to connect them. To “close” a jumper you connect the pins with the clip. To “open” a jumper you remove the clip. Sometimes a jumper will have three pins, labeled 1, 2 and 3.
Ad va n c e d S y s t e m Controller AIS-E1 2.6 Clear CMOS (JP1) JP1 Function 1-2 Normal (Default) 2-3 Clear CMOS 2.7 Auto Power Button (JP3) JP3 Function 1-2 ATX (Default) 2-3 AT 2.8 +12V/+5V/Ring Selection (JP6) JP6 Function 1-2 +12V 3-4 Ring (Default) 5-6 +5V 2.9 Inverter Power Selection (JP7) JP7 Function 1-2 +12V (Default) 2-3 +5V 2.10 Digital I/O (DIO1) This connector offers 4-pair of digital I/O functions and address is A00H.
Ad va n c e d S y s t e m Controller AIS-E1 The pin definitions and registers mapping are illustrated below: Address: A00H 4 in / 4 out Pin1 Pin2 Pin3 Pin4 Pin5 Pin6 Pin7 Pin8 GPI 11 GPI 12 GPI 14 GPI 34 GPO 35 GPO 36 GPO 37 GPO 63 Pin1 Pin2 Pin3 Pin4 Pin5 Pin6 Pin7 Pin8 GPI 11 GPI 12 GPI 14 GPI 34 GPO 35 GPO 36 GPO 37 GPO 63 Pin1 Pin2 Pin3 Pin4 Pin5 Pin6 Pin7 Pin8 GPI 11 GPI 12 GPI 14 GPI 34 GPO 35 GPO 36 GPO 37 GPO 63 8 in 8 out 2.
Ad va n c e d S y s t e m Controller AIS-E1 2.13 LAN1~LAN2 Active /Link/ Speed LED (CN6) P in S ignal 4B 25B Pin S ignal 5B 1 LAN1_LED_D2 2 LAN1_LED_LNK#_ACT 3 LAN1_LED_1000# 4 LAN1_LED_100# 5 LAN2_LED_D2 6 LAN2_LED_LNK#_ACT 7 LAN2_LED_1000# 8 LAN2_LED_100# 2.14 RS-232/422/485 Connector (COM2) Different device implement the RS-232/422/485 standard in different ways. If you have problems with a serial device, check the pin assignments below for the connector.
Ad va n c e d S y s t e m Controller AIS-E1 5 GND 6 DSR 7 RTS 8 CTS 9 RI 2.
Ad va n c e d S y s t e m Controller 2.
Ad va n c e d S y s t e m Controller AIS-E1 Step 3: Get the HDD Bracket and fasten the four screws with the HDD Step 4: Put the HDD and bracket back to the chassis by sliding the HDD bracket and lock to the position.
Ad va n c e d S y s t e m Controller AIS-E1 Step 5: Fasten the screw to finish installing the HDD 2.18 Installing Three 2.5” Hard Disk Drives If you have three HDD to install, please refer to the installation below.
Ad va n c e d S y s t e m Controller AIS-E1 Step 2: Open the upper cover of the AIS-E1 Step 3: Put the blue rubber damper to the 3-layer HDD bracket and move the damper to the smaller fillister (you have to put 12 blue rubber dampers if you have three HDD to install) Chapter 2 Hardware Installation 2-15
Ad va n c e d S y s t e m Controller AIS-E1 Step 4: Get the four screws ready and pierce to the dampers and lock the HDD (12 screws for three HDD installations) Chapter 2 Hardware Installation 2-16
Ad va n c e d S y s t e m Controller AIS-E1 Step 5: Make sure that the fillisters of the 3-layer HDD bracket has been latched to I-shape nails (blue circles) fillister fillister 3-layer HDD bracket Chapter 2 Hardware Installation 2-17
Ad va n c e d S y s t e m Controller AIS-E1 Step 6: Fasten the screw to lock the HDD bracket with the Chassis and you’ve done installing the three HDD Chapter 2 Hardware Installation 2-18
Ad va n c e d S y s t e m Controller AIS-E1 Chapter 3 AMI BIOS Setup Chapter 3 AMI BIOS Setup 3-1
Ad va n c e d S y s t e m Controller 3.1 AIS-E1 System Test and Initialization These routines test and initialize board hardware. If the routines encounter an error during the tests, you will either hear a few short beeps or see an error message on the screen. There are two kinds of errors: fatal and non-fatal. The system can usually continue the boot up sequence with non-fatal errors.
Ad va n c e d S y s t e m Controller 3.2 AIS-E1 AMI BIOS Setup AMI BIOS ROM has a built-in Setup program that allows users to modify the basic system configuration. This type of information is stored in battery-backed CMOS RAM so that it retains the Setup information when the power is turned off. Entering Setup Power on the computer and press or immediately. This will allow you to enter Setup. Main Set the date, use tab to switch between date elements.
Ad va n c e d S y s t e m Controller AIS-E1 Chapter 4 Driver Installation .
Ad va n c e d S y s t e m Controller AIS-E1 The AIS-E1 comes with an AutoRun DVD-ROM that contains all drivers and utilities that can help you to install the driver automatically. Insert the driver DVD, the driver DVD-title will auto start and show the installation guide. If not, please follow the sequence below to install the drivers.
Ad va n c e d S y s t e m Controller 4.1 AIS-E1 Installation: Insert the AIS-E1 DVD-ROM into the DVD-ROM drive. And install the drivers from Step 1 to Step 8 in order. Step 1 – Install Chipset Driver 1. Click on the STEP 1-CHIPSET folder and select the OS folder your system is 2. Double click on the infinst_autol.exe file located in each OS folder 3. Follow the instructions that the window shows 4. The system will help you install the driver automatically Step 2 – Install VGA Driver 1.
Ad va n c e d S y s t e m Controller AIS-E1 Note 2: If the OS is Windows® XP, you have to install the driver of dotNet Framework first. Simply click on dotnetfx35.exe located in dotNet Framwork folder. Step 3 –Install LAN Driver 1. Click on the STEP3-LAN folder and select the OS folder your system is 2. Select the folder of LAN chip (Intel 82579LM or Realtek 8111E) based on the system adopted. Double click on the .exe file located in the LAN chip folder 3.
Ad va n c e d S y s t e m Controller AIS-E1 automatically Step 6 – Install RAID & AHCI Driver Please refer to the Appendix C RAID & AHCI Settings Step 7 – Install TPM Driver 1. Click on the STEP7-TPM folder and select the folder of OS folder your system is 2. Double click on the Setup.exe located in each OS folder 3. Follow the instructions that the window shows 4. The system will help you install the driver automatically Step 8 –Install Serial Port Driver (Optional) For Windows® XP 32-bit 1.
Ad va n c e d S y s t e m Controller AIS-E1 For Windows® 7 32-bit/ 64-bit 1. Create a password for Administrator account. 2.
Ad va n c e d S y s t e m Controller AIS-E1 3. Reboot and Administrator login. 4. To run patch.bat with [Run as administrator].
Ad va n c e d S y s t e m Controller AIS-E1 You also can install the serial port driver for Windows 7 by the Installation Procedure 2 below: -Win7 32-bit Copy the Driver CD\Serial Port Driver (Optional) \WIN7_32\ win7_X86 \serial.sys to C:\WINDOWS\system32\drivers\ -Win7 64-bit Copy the Driver CD\Serial Port Driver (Optional) \WIN7_64 \win7_amd64\serial.
Ad va n c e d S y s t e m Controller AIS-E1 Appendix A Programming the Watchdog Timer Appendix A Programming the Watchdog Timer A-1
Ad va n c e d S y s t e m Controller AIS-E1 A.1 Programming AIS-E1 utilizes ITE IT8728 chipset as its watchdog timer controller. Below are the procedures to complete its configuration and the AAEON intial watchdog timer program is also attached based on which you can develop customized program to fit your application. Configuring Sequence Description After the hardware reset or power-on reset, the ITE 8728 enters the normal mode with all logical devices disabled except KBC.
Ad va n c e d S y s t e m Controller AIS-E1 There are three steps to complete the configuration setup: (1) Enter the MB PnP Mode; (2) Modify the data of configuration registers; (3) Exit the MB PnP Mode. Undesired result may occur if the MB PnP Mode is not exited normally. (1) Enter the MB PnP Mode To enter the MB PnP Mode, four special I/O write operations are to be performed during Wait for Key state.
Ad va n c e d S y s t e m Controller AIS-E1 WatchDog Timer Configuration Registers Configure Control (Index=02h) This register is write only. Its values are not sticky; that is to say, a hardware reset will automatically clear the bits, and does not require the software to clear them.
Ad va n c e d S y s t e m Controller AIS-E1 WatchDog Timer Control Register (Index=71h, Default=00h) WatchDog Timer Configuration Register (Index=72h, Default=00h) WatchDog Timer Time-out Value Register (Index=73h, Default=00h) Appendix A Programming the Watchdog Timer A-5
Ad va n c e d S y s t e m Controller AIS-E1 A.2 ITE8728 Watchdog Timer Initial Program .MODEL SMALL .CODE Main: CALL Enter_Configuration_mode CALL Check_Chip mov cl, 7 call Set_Logic_Device ;time setting mov cl, 10 ; 10 Sec dec al Watch_Dog_Setting: ;Timer setting mov al, cl mov cl, 73h call Superio_Set_Reg ;Clear by keyboard or mouse interrupt mov al, 0f0h mov cl, 71h call Superio_Set_Reg ;unit is second.
Ad va n c e d S y s t e m Controller AIS-E1 ; game port enable mov cl, 9 call Set_Logic_Device Initial_OK: CALL Exit_Configuration_mode MOV AH,4Ch INT 21h Enter_Configuration_Mode PROC NEAR MOV SI,WORD PTR CS:[Offset Cfg_Port] MOV DX,02Eh MOV CX,04h Init_1: MOV AL,BYTE PTR CS:[SI] OUT DX,AL INC SI LOOP Init_1 RET Enter_Configuration_Mode ENDP Exit_Configuration_Mode PROC NEAR MOV AX,0202h CALL Write_Configuration_Data Appendix A Programming the Watchdog Timer A-7
Ad va n c e d S y s t e m Controller AIS-E1 RET Exit_Configuration_Mode ENDP Check_Chip PROC NEAR MOV AL,20h CALL Read_Configuration_Data CMP AL,87h JNE Not_Initial MOV AL,21h CALL Read_Configuration_Data CMP AL,12h JNE Not_Initial Need_Initial: STC RET Not_Initial: CLC RET Check_Chip ENDP Read_Configuration_Data PROC NEAR MOV DX,WORD PTR CS:[Cfg_Port+04h] OUT DX,AL Appendix A Programming the Watchdog Timer A-8
Ad va n c e d S y s t e m Controller AIS-E1 MOV DX,WORD PTR CS:[Cfg_Port+06h] IN AL,DX RET Read_Configuration_Data ENDP Write_Configuration_Data PROC NEAR MOV DX,WORD PTR CS:[Cfg_Port+04h] OUT DX,AL XCHG AL,AH MOV DX,WORD PTR CS:[Cfg_Port+06h] OUT DX,AL RET Write_Configuration_Data ENDP Superio_Set_Reg proc near push ax MOV DX,WORD PTR CS:[Cfg_Port+04h] mov al,cl out dx,al pop ax inc dx out dx,al ret Superio_Set_Reg endp.
Ad va n c e d S y s t e m Controller AIS-E1 push ax push cx xchg al,cl mov cl,07h call Superio_Set_Reg pop cx pop ax ret Set_Logic_Device endp ;Select 02Eh->Index Port, 02Fh->Data Port Cfg_Port DB 087h,001h,055h,055h DW 02Eh,02Fh END Main Note: Interrupt level mapping 0Fh-Dh: not valid 0Ch: IRQ12 . .
Ad va n c e d S y s t e m Controller AIS-E1 Appendix B I/O Information Appendix B I/O Information B-1
Ad va n c e d S y s t e m Controller B.
Ad va n c e d S y s t e m Controller AIS-E1 Appendix B I/O Information B-3
Ad va n c e d S y s t e m Controller B.
Ad va n c e d S y s t e m Controller AIS-E1 B.3 IRQ Mapping Chart B.
Ad va n c e d S y s t e m Controller AIS-E1 Appendix C RAID & AHCI Settings Appendix C RAID & AHCI Settings C-1
Ad va n c e d S y s t e m Controller AIS-E1 C.
Ad va n c e d S y s t e m Controller AIS-E1 Step 3: The setting procedures “ In BIOS Setup Menu” A: Advanced -> SATA Configuration -> SATA Mode -> RAID Mode Step 4: The setting procedures “In BIOS Setup Menu” B: Advanced -> Launch Storage OpROM -> Enabled Appendix C RAID & AHCI Settings C-3
Ad va n c e d S y s t e m Controller AIS-E1 Step 5: The setting procedures “In BIOS Setup Menu” C: Boot -> Boot Option #1 -> DVD-ROM Type Step 6: The setting procedures “In BIOS Setup Menu” D: Save & Exit -> Save Changes and Exit Appendix C RAID & AHCI Settings C-4
Ad va n c e d S y s t e m Controller AIS-E1 Step 7: Press Ctrl-I to enter MAIN MENU Step 8: Choose “1.
Ad va n c e d S y s t e m Controller Step 9: RAID Level -> RAID0(Stripe) Step 10: Choose “Create Volume” Appendix C RAID & AHCI Settings C-6 AIS-E1
Ad va n c e d S y s t e m Controller AIS-E1 Step 11: Choose “Y” Step 12: Choose “5.
Ad va n c e d S y s t e m Controller Step 13: Choose “Y” Step 14: Setup OS Appendix C RAID & AHCI Settings C-8 AIS-E1
Ad va n c e d S y s t e m Controller AIS-E1 Step 15: Press “F6” Step 16: Choose “S” Appendix C RAID & AHCI Settings C-9
Ad va n c e d S y s t e m Controller AIS-E1 Step 17: Choose “Intel(R) ICH8M-E/ICH9M-E/5 Series SATA RAID Controller” Step 18: It will show the model number you select and then press “ENTER” Appendix C RAID & AHCI Settings C-10
Ad va n c e d S y s t e m Controller AIS-E1 Step 19: Setup is starting Windows Appendix C RAID & AHCI Settings C-11
Ad va n c e d S y s t e m Controller AIS-E1 C.
Ad va n c e d S y s t e m Controller AIS-E1 Step 3: The setting procedures “ In BIOS Setup Menu” A: Advanced -> SATA Configuration -> SATA Configuration -> SATA Mode -> AHCI Mode Step 4: The setting procedures “In BIOS Setup Menu” B: Boot -> Boot Option #1 -> DVD-ROM Type Appendix C RAID & AHCI Settings C-13
Ad va n c e d S y s t e m Controller AIS-E1 Step 5: The setting procedures “In BIOS Setup Menu” C: Save & Exit -> Save Changes and Exit Step 6: Setup OS Appendix C RAID & AHCI Settings C-14
Ad va n c e d S y s t e m Controller AIS-E1 Step 7: Press “F6” Step 8: Choose “S” Appendix C RAID & AHCI Settings C-15
Ad va n c e d S y s t e m Controller AIS-E1 Step 9: Choose “Intel(R) 5 Series 6 Port SATA AHCI Controller” Step 10: It will show the model number you select and then press “ENTER” Appendix C RAID & AHCI Settings C-16
Ad va n c e d S y s t e m Controller AIS-E1 Step 11: Setup is loading files Appendix C RAID & AHCI Settings C-17
