A d va n c e d S ys t e m Controller AIS-E2-CV1 AIS-E2-CV1 Advanced System Controller 2.5” HDD/SSD x 2 Gigabit Ethernet x 2 COM x 6, USB2.0 x 6 HD Audio Codec AIS-E2-CV1 Manual 1st Ed.
A d va n c e d S ys t e m Controller AIS-E2-CV1 Copyright Notice T This document is copyrighted, 2013. All rights are reserved. The original manufacturer reserves the right to make improvements to the products described in this manual at any time without notice. No part of this manual may be reproduced, copied, translated, or transmitted in any form or by any means without the prior written permission of the original manufacturer.
A d va n c e d S ys t e m Controller AIS-E2-CV1 Acknowledgments All other products’ name or trademarks are properties of their respective owners. AMI is a trademark of American Megatrends Inc. CompactFlash™ is a trademark of the Compact Flash Association. Intel® , Atom Microsoft Windows® is a registered trademark of Microsoft Corp. ITE is a trademark of Integrated Technology Express, Inc. IBM, PC/AT, PS/2, and VGA are trademarks of International Business Machines Corporation.
A d va n c e d S ys t e m Controller AIS-E2-CV1 Packing List Before you begin operating your PC, please make sure that the following materials are enclosed: 1 9761E20000 Gift Box (Including 84W Power adapter, CPU Cooler) 1 DVD-ROM for manual (in PDF format) and drivers 1 AIS-E2-CV1 If any of these items should be missing or damaged, please contact your distributor or sales representative immediately.
A d va n c e d S ys t e m Controller AIS-E2-CV1 Safety & Warranty 1. Read these safety instructions carefully. 2. Keep this user's manual for later reference. 3. Disconnect this equipment from any AC outlet before cleaning. Do not use liquid or spray detergents for cleaning. Use a damp cloth. 4. For pluggable equipment, the power outlet must be installed near the equipment and must be easily accessible. 5. Keep this equipment away from humidity. 6. Put this equipment on a firm surface during installation.
A d va n c e d S ys t e m Controller AIS-E2-CV1 d. The equipment does not work well, or you cannot get it to work according to the user’s manual. e. The equipment has been dropped and damaged. f. The equipment has obvious signs of breakage. 15. DO NOT LEAVE THIS EQUIPMENT IN AN ENVIRONMENT WHERE THE STORAGE TEMPERATURE IS BELOW -20°C (-4°F) OR ABOVE 60°C (140°F). IT MAY DAMAGE THE EQUIPMENT. FCC This device complies with Part 15 FCC Rules.
A d va n c e d S ys t e m Controller AIS-E2-CV1 Below Table for China RoHS Requirements 产品中有毒有害物质或元素名称及含量 AAEON Boxer/ Industrial System 有毒有害物质或元素 部件名称 铅 汞 镉 (Pb) (Hg) (Cd) (Cr(VI)) (PBB) (PBDE) × ○ ○ ○ ○ ○ × ○ ○ ○ ○ ○ × ○ ○ ○ ○ ○ × ○ ○ ○ ○ ○ 硬盘 × ○ ○ ○ ○ ○ 电源 × ○ ○ ○ ○ ○ 印刷电路板 六价铬 多溴联苯 多溴二苯醚 及其电子组件 外部信号 连接器及线材 外壳 中央处理器 与内存 O：表示该有毒有害物质在该部件所有均质材料中的含量均在 SJ/T 11363-2006 标准规定的限量要求以下。 X：表示该有毒有害物质至少在该部件的某一均质材料中的含量超出 SJ/T 11363-2006 标准规定的限量要求。 备注： 一、此产品所标示之环保使用期
A d va n c e d S ys t e m Controller AIS-E2-CV1 Contents T Chapter 1 General Information 1.1 Introduction ................................................................ 1-2 1.2 Features .................................................................... 1-3 1.3 Specifications ............................................................ 1-4 Chapter 2 Hardware Installation 2.1 Location of Connectors and Jumpers of the Main Board ..........................................................................
A d va n c e d S ys t e m Controller AIS-E2-CV1 2.15 CPU/SYSTEM FAN Connector (CPU_FAN/CHA_FAN) ......................................................................................... 2-10 2.16 COM3/COM4/COM5 RS232 Serial Port PIN HEADER (COM3/COM4/COM5) ..................................................... 2-11 2.17 GPIO/SM BUS/COM2/ COM2 External Power Selection (DIGITALREFENCE) ....................................................... 2-11 2.18 COM2 RS-232/422/485 connector ..........................
A d va n c e d S ys t e m Controller Appendix B AIS-E2-CV1 I/O Information B.1 I/O Address Map ....................................................B-2 st B.2 1 MB Memory Address Map ................................B-4 B.3 IRQ Mapping Chart ................................................B-5 B.4 DMA Channel Assignments.……………………… . B-6 Appendix C AHCI Setting C.1 Setting AHCI .........................................................
A d va n c e d S ys t e m Controller AIS-E2-CV1 Chapter 1 General Information Chapter 1 General Information 1- 1
A d va n c e d S ys t e m Controller AIS-E2-CV1 1.1 Introduction ® AIS-E2-CV1 adopts the Intel Atom TM D2550 Processor and ® equipped with Intel NM10 chipset. Moreover, the system memory features two 204-pin dual-channel DDR3 1066/800 MHz SODIMM up to 4 GB. It deploys two LAN ports that consist of 10/100/1000Base-TX Ethernet RJ-45 ports. AIS-E2-CV1 condensed appearance features desktop and wallmount form factor that fits nicely into a space-limited environment.
A d va n c e d S ys t e m Controller AIS-E2-CV1 1.2 Features ® Intel Atom™ D2550 Processor Intel NM10 Chipset 204-pin Dual-Channel DDR3 1066/800 MHz SODIMM x 2 (Up ® to 4GB) Dual Realtek Gigabit Ethernet Ports SATA 3.0Gb/s x 2 USB 2.
A d va n c e d S ys t e m Controller AIS-E2-CV1 1.3 Specifications ® CPU Intel Atom™ D2550 Processor Chipset Intel NM10 System Memory 204-pin Dual-Channel DDR3 ® 1066/800 MHz SODIMM x 2, up to 4GB Display VGA DB-15 x 1 DVI DVI-D x 1 Others － SSD/HDD 2.5” HDD/SSD x 2 LAN Gigabit Ethernet Wireless Optional by Mini Card USB Host USB2.0 x 2 Others Power Switch x 1, Reset button x 1 USB Host USB2.
A d va n c e d S ys t e m Controller System Cooling AIS-E2-CV1 CPU cooler x 1 System Cooler x 1 Mounting Wallmount Operating Temperature 32°F ~ 104°F (0°C ~ 40°C) Storage Temperature -4°F ~ 140°F (-20°C ~ 60°C) Anti-Vibration 0.5g rms / 5 ~ 500Hz / operation Anti-Shock 15 G peak acceleration (11 msec. duration) Certification EMC Dimension (W x H x D) CE/ FCC class A 7.68" x 2.76" x 8.66" (195mm x 70mm x 220mm) Weight 13.84 lb (6.
A d va n c e d S ys t e m Controller AIS-E2-CV1 Chapter 2 Hardware Installation Chapter 2 Hardware Installation 2-1
A d va n c e d S ys t e m Controller 2.1 AIS-E2-CV1 Location of Connectors and Jumpers of the Main Board NOTE: If choose m-SATA SKU, SATA3G_2 port, mini card and SIM card slot will be disable.
A d va n c e d S ys t e m Controller 2.
A d va n c e d S ys t e m Controller I/O Ports Chapter 2 Hardware Installation 2-4 AIS-E2-CV1
A d va n c e d S ys t e m Controller 2.3 AIS-E2-CV1 List of Jumpers The board has a number of jumpers that allow you to configure your system to suit your application.
A d va n c e d S ys t e m Controller 2.4 AIS-E2-CV1 List of Connectors The board has a number of connectors that allow you to configure your system to suit your application.
A d va n c e d S ys t e m Controller SATA3G_2 SATA 1 Connector USB56 USB 5 & 6 Pin Header USB7 USB 7 Pin Header WLAN Mini PCI-E Slot AIS-E2-CV1 NOTE: The +12V Power connector (Label: DC_PWR) is lockable Jack type with screw. Please refer the inner and outer diameter dimension of connector as below to choose suitable adaptor.
A d va n c e d S ys t e m Controller 2.5 AIS-E2-CV1 Setting Jumpers You configure your card to match the needs of your application by setting jumpers. A jumper is the simplest kind of electric switch. It consists of two metal pins and a small metal clip (often protected by a plastic cover) that slides over the pins to connect them. To “close” a jumper you connect the pins with the clip. To “open” a jumper you remove the clip. Sometimes a jumper will have three pins, labeled 1, 2 and 3.
A d va n c e d S ys t e m Controller 2.6 2.7 2.8 2.9 AIS-E2-CV1 AT/ATX Mode Selection (ATMODE) ATOMODE Function Close 1-2 AT Close 2-3 ATX Mode (Default) Clear COMS (CLRTC) CLRTC Function Close 1-2 Protected (Default) Close 2-3 Clear COM2 External Power Selection (DIGITALREFENCE) DIGITALREFENCE Function Close 15-16 +12V Close 17-18 RI# (Default) Close 19-20 +5V LVDS Panel Power Selection (LVDS_VDD_SEL) LVDS_VDD_SEL Function Close 1-2 +3.3V (Default) Close 2-3 +5V 2.
A d va n c e d S ys t e m Controller Close 2-3 AIS-E2-CV1 PWM Control 2.11 LVDS function Enable (LVDS_SWITCH) LVDS_SWITCH Function Close 1-2 Disable Close 2-3 Enable (Default) 2.12 LVDS Panel Backlight Power Selection (LCD_POWER_SEL) LCD_POWER_SEL Function Close 1-2 +12V Close 2-3 +5V (Default) 2.13 Watchdog Timer Function Switch (WDT) WDT Function Close 1-2 Disable (Default) Close 2-3 Enable 2.
A d va n c e d S ys t e m Controller AIS-E2-CV1 2.16 COM3/COM4/COM5 RS-232 Serial Port PIN HEADER (COM3/COM4/COM5) Pin Signal Pin Signal 1 DCD 2 RXD 3 TXD 4 DTR 5 GND 6 DSR 7 RTS 8 CTS 9 RI 10 NC 2.
A d va n c e d S ys t e m Controller AIS-E2-CV1 2.18 COM2 RS-232/422/485 connector Pin Signal Pin Signal 1 DCD (422TXD-/485DATA-) 2 RXD (422RXD+) 3 TXD (422TXD+/485DATA+) 4 DTR (422RXD-) 5 GND 6 DSR 7 RTS 8 CTS 9 RI/+12V/+5V 10 N.C. 2.19 Front Panel Pin Header (F_PANEL) Pin Signal Pin Signal 1 HDDLED+ 2 POWERLED+ 3 HDDLED- 4 POWERLED- 5 RESET- 6 PWRBTN+ 7 RESET+ 8 PWRBTN- 9 N/C 2.
A d va n c e d S ys t e m Controller 3 GND 5 Panel backlight control AIS-E2-CV1 4 GND 2.22 Parallel Port Connector (LPT) Pin Signal Pin Signal 1 STB# 2 AFD# 3 DATA 0 4 ERROR# 5 DATA 1 6 INIT# 7 DATA 2 8 SLIN# 9 DATA 3 10 GND 11 DATA 4 12 GND 13 DATA 5 14 GND 15 DATA 6 16 GND 17 DATA 7 18 GND 19 ACK# 20 GND 21 BUSY 22 GND 23 PE 24 GND 25 SLCT 2.
A d va n c e d S ys t e m Controller AIS-E2-CV1 7 NC 8 NC 9 NC 10 NC 11 NC 12 NC 13 DDC_DATA 14 DDC_CLOCK 15 DATA3- 16 DATA3+ 17 DATA2- 18 DATA2+ 19 DATA1- 20 DATA1+ 21 DATA0- 22 DATA0+ 23 Panel power 24 GND 25 LVDS_CLOCK- 26 LVDS_CLOCK+ 27 Panel power 28 GND 29 Backlight enable 30 Brightness control NOTE: LVDS connector Vendor: PINREX; Model: 712-76-30GWR8. Please refer the drawing below, notice the location of PIN1, PIN2, PIN29 and PIN30.
A d va n c e d S ys t e m Controller AIS-E2-CV1 2.24 Serial ATA Power Connector (SATA_PWR1) Pin Signal Pin Signal 1 +5 2 GND 3 GND 4 +12V 2.25 USB 5 & 6 PIN HEADER (USB56) Pin Signal Pin Signal 1 +5V 2 GND 3 USBD- 4 GND 5 USBD+ 6 USBD+ 7 GND 8 USBD- 9 GND 10 +5V 2.
A d va n c e d S ys t e m Controller AIS-E2-CV1 2.27 Installing the 2.
A d va n c e d S ys t e m Controller AIS-E2-CV1 Step 2: Push back the upper lid of AIS-E2-CV1 and open it Step 3: Get the HDD bracket ready and insert the dampers to the holes on the bracket Chapter 2 Hardware Installation 2-17
A d va n c e d S ys t e m Controller Chapter 2 Hardware Installation 2-18 AIS-E2-CV1
A d va n c e d S ys t e m Controller AIS-E2-CV1 Step 4: Pierce the four screws to the dampers Chapter 2 Hardware Installation 2-19
A d va n c e d S ys t e m Controller AIS-E2-CV1 Step 5: Get the 2.
A d va n c e d S ys t e m Controller AIS-E2-CV1 Step 7: Connect the SATA and Power cables Step 8: Close the HDD bracket and finish the installation Chapter 2 Hardware Installation 2-21
A d va n c e d S ys t e m Controller AIS-E2-CV1 Chapter 3 AMI BIOS Setup Chapter 3 AMI BIOS Setup 3-1
A d va n c e d S ys t e m Controller 3.1 AIS-E2-CV1 System Test and Initialization These routines test and initialize board hardware. If the routines encounter an error during the tests, you will either hear a few short beeps or see an error message on the screen. There are two kinds of errors: fatal and non-fatal. The system can usually continue the boot up sequence with non-fatal errors.
A d va n c e d S ys t e m Controller 3.2 AIS-E2-CV1 AMI BIOS Setup AMI BIOS ROM has a built-in Setup program that allows users to modify the basic system configuration. This type of information is stored in battery-backed CMOS RAM so that it retains the Setup information when the power is turned off. Entering Setup Power on the computer and press or immediately. This will allow you to enter Setup. Main Set the date, use tab to switch between date elements.
A d va n c e d S ys t e m Controller AIS-E2-CV1 Chapter 4 Driver Installation 0B .
A d va n c e d S ys t e m Controller AIS-E2-CV1 The AIS-E2-CV1 comes with an AutoRun DVD-ROM that contains all drivers and utilities that can help you to install the driver automatically. Insert the driver DVD, the driver DVD-title will auto start and show the installation guide. If not, please follow the sequence below to install the drivers.
A d va n c e d S ys t e m Controller 4.1 AIS-E2-CV1 Installation: Insert the AIS-E2-CV1 DVD-ROM into the DVD-ROM drive. And install the drivers from Step 1 to Step 5 in order. Step 1 – Install Chipset Driver 1. Click on the Step 1 - INF folder and select the OS your system is 2. Double click on the .exe file located in each OS folder 3. Follow the instructions that the window shows 4. The system will help you install the driver automatically Step 2 – Install VGA Driver ® For Windows 7 1.
A d va n c e d S ys t e m Controller AIS-E2-CV1 2. Install IEMGD Select the WINXP folder and double click on the IEMGDInstall.
A d va n c e d S ys t e m Controller AIS-E2-CV1 Chapter 4 Driver Installation 4 -5
A d va n c e d S ys t e m Controller AIS-E2-CV1 If you want to update driver, please uninstall driver first. Uninstall IEMGD 1. Double click on the IEMGDInstall.exe 2. Follow the instructions that the window shows 3. The system will help you uninstall the driver automatically Step 3 – Install LAN Driver 1. Click on the Step 3 - LAN folder and select the OS folder your system is 2. Double click on the setup.exe file located in each OS folder 3. Follow the instructions that the window shows 4.
A d va n c e d S ys t e m Controller AIS-E2-CV1 4.
A d va n c e d S ys t e m Controller AIS-E2-CV1 Appendix A Programming the Watchdog Timer Appendix A Programming the Watchdog Timer A-1
A d va n c e d S ys t e m Controller AIS-E2-CV1 A.1 Programming AIS-E2-CV1 utilizes ITE 8783 chipset as its watchdog timer controller. Below are the procedures to complete its configuration and this initial watchdog timer program is also attached based on which you can develop customized program to fit your application. Configuring Sequence Description After the hardware reset or power-on reset, the ITE 8783 enters the normal mode with all logical devices disabled except KBC.
A d va n c e d S ys t e m Controller AIS-E2-CV1 There are three steps to complete the configuration setup: (1) Enter the MB PnP Mode; (2) Modify the data of configuration registers; (3) Exit the MB PnP Mode. Undesired result may occur if the MB PnP Mode is not exited normally. (1) Enter the MB PnP Mode To enter the MB PnP Mode, four special I/O write operations are to be performed during Wait for Key state.
A d va n c e d S ys t e m Controller AIS-E2-CV1 WatchDog Timer Configuration Registers Configure Control (Index=02h) This register is write only. Its values are not sticky; that is to say, a hardware reset will automatically clear the bits, and does not require the software to clear them.
A d va n c e d S ys t e m Controller AIS-E2-CV1 Watch Dog Timer 1, 2, 3 Configuration Register (Index=72h, 82h, 92h Default=001s0000b) Watch Dog Timer 1,2,3 Time-Out Value (LSB) Register (Index=73h,83h,93h, Default=38h) Watch Dog Timer 1,2,3 Time-Out Value (MSB) Register (Index=74h,84h,94h Default=00h) Appendix A Programming the Watchdog Timer A-5
A d va n c e d S ys t e m Controller AIS-E2-CV1 A.2 ITE8783 Watchdog Timer Initial Program .MODEL SMALL .CODE Main: CALL Enter_Configuration_mode CALL Check_Chip mov cl, 7 call Set_Logic_Device ;time setting mov cl, 10 ; 10 Sec dec al Watch_Dog_Setting: ;Timer setting mov al, cl mov cl, 73h call Superio_Set_Reg ;Clear by keyboard or mouse interrupt mov al, 0f0h mov cl, 71h call Superio_Set_Reg ;unit is second.
A d va n c e d S ys t e m Controller AIS-E2-CV1 call Superio_Set_Reg ; game port enable mov cl, 9 call Set_Logic_Device Initial_OK: CALL Exit_Configuration_mode MOV AH,4Ch INT 21h Enter_Configuration_Mode PROC NEAR MOV SI,WORD PTR CS:[Offset Cfg_Port] MOV DX,02Eh MOV CX,04h Init_1: MOV AL,BYTE PTR CS:[SI] OUT DX,AL INC SI LOOP Init_1 RET Enter_Configuration_Mode ENDP Exit_Configuration_Mode PROC NEAR MOV AX,0202h Appendix A Programming the Watchdog Timer A-7
A d va n c e d S ys t e m Controller CALL Write_Configuration_Data RET Exit_Configuration_Mode ENDP Check_Chip PROC NEAR MOV AL,20h CALL Read_Configuration_Data CMP AL,87h JNE Not_Initial MOV AL,21h CALL Read_Configuration_Data CMP AL,81h JNE Not_Initial Need_Initial: STC RET Not_Initial: CLC RET Check_Chip ENDP Read_Configuration_Data PROC NEAR MOV DX,WORD PTR CS:[Cfg_Port+04h] Appendix A Programming the Watchdog Timer A-8 AIS-E2-CV1
A d va n c e d S ys t e m Controller AIS-E2-CV1 OUT DX,AL MOV DX,WORD PTR CS:[Cfg_Port+06h] IN AL,DX RET Read_Configuration_Data ENDP Write_Configuration_Data PROC NEAR MOV DX,WORD PTR CS:[Cfg_Port+04h] OUT DX,AL XCHG AL,AH MOV DX,WORD PTR CS:[Cfg_Port+06h] OUT DX,AL RET Write_Configuration_Data ENDP Superio_Set_Reg proc near push ax MOV DX,WORD PTR CS:[Cfg_Port+04h] mov al,cl out dx,al pop ax inc dx out dx,al ret Superio_Set_Reg endp.
A d va n c e d S ys t e m Controller Set_Logic_Device proc AIS-E2-CV1 near push ax push cx xchg al,cl mov cl,07h call Superio_Set_Reg pop cx pop ax ret Set_Logic_Device endp ;Select 02Eh->Index Port, 02Fh->Data Port Cfg_Port DB 087h,001h,055h,055h DW 02Eh,02Fh END Main Note: Interrupt level mapping 0Fh-Dh: not valid 0Ch: IRQ12 . .
A d va n c e d S ys t e m Controller AIS-E2-CV1 Appendix B I/O Information Appendix B I/O Information B-1
A d va n c e d S ys t e m Controller B.
A d va n c e d S ys t e m Controller AIS-E2-CV1 Appendix B I/O Information B-3
A d va n c e d S ys t e m Controller st B.
A d va n c e d S ys t e m Controller AIS-E2-CV1 B.
A d va n c e d S ys t e m Controller B.
A d va n c e d S ys t e m Controller AIS-E2-CV1 Appendix C AHCI Setting Appendix C AHCI Setting C-1
A d va n c e d S ys t e m Controller AIS-E2-CV1 C.1 Setting AHCI OS installation to SETUP AHCI Mode Step 1: Copy below files from “Driver CD -> Step 5 – AHCI\Floppy” and to diskette. Step 2: Connect the USB Floppy drive to the system and insert the diskette from previous step.
A d va n c e d S ys t e m Controller AIS-E2-CV1 Step 4: Configure DVD/CD-ROM drive as the first boot device.
A d va n c e d S ys t e m Controller AIS-E2-CV1 Step 6 – Boot to DVD/CD-ROM device to install OS Step 7 – Press “F6” to install AHCI driver Step 8 – Press “S” to install AHCI driver Step 9 – Choose “Intel(R) NM10 Express Chipset” Step 10 – Windows Setup will display the controller name you selected in previous step and continue to install OS when ”ENTER” pressed.
