Ad va n c e d S y s t e m Controller AIS-Q454 AIS-Q454 Advanced System Controller 2 3.5” Hard Disk Drive Bay 2 Gigabit Ethernet/ 2 COM/ 6 USB2.0 HD Audio Codec AIS-Q454 Manual 1st Ed.
Ad va n c e d S y s t e m Controller AIS-Q454 Copyright Notice This document is copyrighted, 2010. All rights are reserved. The original manufacturer reserves the right to make improvements to the products described in this manual at any time without notice. No part of this manual may be reproduced, copied, translated, or transmitted in any form or by any means without the prior written permission of the original manufacturer. Information provided in this manual is intended to be accurate and reliable.
Ad va n c e d S y s t e m Controller AIS-Q454 Acknowledgments All other products’ name or trademarks are properties of their respective owners. • Award is a trademark of Award Software International, Inc. • CompactFlash™ is a trademark of the Compact Flash Association. • Microsoft Windows is a registered trademark of Microsoft Corp. • Intel®, Core™ 2 Duo, Core™ 2 Quad are trademarks of Intel Corporation. • PC/AT, PS/2, and VGA are trademarks of International Business Machines Corporation.
Ad va n c e d S y s t e m Controller AIS-Q454 Packing List Before you begin operating your PC, please make sure that the following materials are enclosed: z 4 S221005030 HDD Screws z 8 S225006010 Wallmount Bracket Screws z 2 M04Q452020 Wallmount Brackets z 4 1990666615 Rubber Feet z 1 AIS-Q454 z 1 CD-ROM for manual (in PDF format) and drivers If any of these items should be missing or damaged, please contact your distributor or sales representative immediately.
Ad va n c e d S y s t e m Controller AIS-Q454 Safety & Warranty 1. Read these safety instructions carefully. 2. Keep this user's manual for later reference. 3. Disconnect this equipment from any AC outlet before cleaning. Do not use liquid or spray detergents for cleaning. Use a damp cloth. 4. For pluggable equipment, the power outlet must be installed near the equipment and must be easily accessible. 5. Keep this equipment away from humidity. 6. Put this equipment on a firm surface during installation.
Ad va n c e d S y s t e m Controller AIS-Q454 d. The equipment does not work well, or you cannot get it to work according to the user’s manual. e. The equipment has been dropped and damaged. f. The equipment has obvious signs of breakage. 15. DO NOT LEAVE THIS EQUIPMENT IN AN ENVIRONMENT WHERE THE STORAGE TEMPERATURE IS BELOW -20°C (-4°F) OR ABOVE 65°C (149°F). IT MAY DAMAGE THE EQUIPMENT. FCC This device complies with Part 15 FCC Rules.
Ad va n c e d S y s t e m Controller AIS-Q454 Below Table for China RoHS Requirements 产品中有毒有害物质或元素名称及含量 AAEON Boxer/ Industrial System 有毒有害物质或元素 部件名称 铅 汞 镉 六价铬 多溴联苯 多溴二苯醚 (Pb) (Hg) (Cd) (Cr(VI)) (PBB) (PBDE) × ○ ○ ○ ○ ○ × ○ ○ ○ ○ ○ × ○ ○ ○ ○ ○ × ○ ○ ○ ○ ○ 硬盘 × ○ ○ ○ ○ ○ 电源 × ○ ○ ○ ○ ○ 印刷电路板 及其电子组件 外部信号 连接器及线材 外壳 中央处理器 与内存 O：表示该有毒有害物质在该部件所有均质材料中的含量均在 SJ/T 11363-2006 标准规定的限量要求以下。 X：表示该有毒有害物质至少在该部件的某一均质材料中的含量超出 SJ/T 11363-2006 标准规定的限量要求。 备注： 一、此产品所标示之环保使用期限，系
Ad va n c e d S y s t e m Controller AIS-Q454 Contents Chapter 1 General Information 1.1 Introduction................................................................ 1-2 1.2 Features .................................................................... 1-3 1.3 Specifications ............................................................ 1-4 Chapter 2 Hardware Installation 2.1 Location of Connectors ............................................. 2-2 2.2 Mechanical Drawing .................................
Ad va n c e d S y s t e m Controller AIS-Q454 2.18 Installing the Hard Disk Drive.................................. 2-13 Chapter 3 Award BIOS Setup 3.1 System Test and Initialization. .................................. 3-2 3.2 Award BIOS Setup .................................................... 3-3 Chapter 4 Driver Installation 4.1 Installation ................................................................. 4-3 Appendix A Programming The Watchdog Timer A.1 Programming ...........................
Ad va n c e d S y s t e m Controller AIS-Q454 Chapter 1 General Information Chapter 1 General Information 1- 1
Ad va n c e d S y s t e m Controller AIS-Q454 1.1 Introduction AIS-Q454 adopts the Intel® CoreTM 2 Duo/ Quad LGA 775 Processors. The chipset is equipped with Intel® Q45 + ICH10DO. Moreover, the system memory features two 240-pin DDRIII 800/1066 SDRAM up to 4GB. It deploys two PCI-Express LAN ports that consist of 10/100/1000Base-TX Ethernet RJ-45 ports. AIS-Q454 condensed appearance features desktop and wallmount form factor that fits nicely into a space-limited environment.
Ad va n c e d S y s t e m Controller AIS-Q454 1.2 Features z Intel® CoreTM 2 Duo/ Quad LGA775 Processors z DDRIII 800/1066 Memory x 2, Up To 4GB z Intel® Integrated Graphics Engine 4500 Supports Dual Views With VGA & GVI z Dual Intel® PCI-Express Gigabit Ethernet z 3.5” SATA II Hard Disk Drive x 2 and Slim Type Combo x 1 (Optional) z USB2.
Ad va n c e d S y s t e m Controller AIS-Q454 1.3 Specifications System Form Factor Compact size for Desktop/Wallmount Main Board IMBI-Q45 Processor Intel® CoreTM 2 Duo/ Quad LGA775 CPU, FSB 800/1066/ 1333 MHz, TDP 95W; Intel® ECG item: Q9400, E8400, E7400, E6500, E6400, E5300, E4300, E3400, E2160 System Memory Dual-channel with 240-pin DDRIII 800/1066 SDRAM x 2, Max.
Ad va n c e d S y s t e m Controller AIS-Q454 Expansion PCI-Express﹝x16﹞x 1, PCI-Express ﹝x4﹞x 1, PCI x 2 Watchdog Timer Reset: 1 sec.~255 min. and 1 sec. or 1 min./step H/W Status Monitor Monitoring system temperature, voltage, and cooling fan status Power Supply Flex ATX 275W input 90~264V AC Dimension (WxHxD) 14.17” x 3.94” x 11.81” (360mm x 100mm x 300mm) External I/O Serial Port RS-232 x 2 KB & Mouse Keyboard x 1 & Mouse x 1 Universal Serial Bus USB2.
Ad va n c e d S y s t e m Controller AIS-Q454 Operating Humidity 10~80% Storage Humidity 10~80%, non-condensing Vibration 0.5G/ 5~500Hz/ operating Shock 15G peak acceleration duration), operating EMI CE & FCC Class A Chapter 1 General Information 1- 6 (11 m sec.
Ad va n c e d S y s t e m Controller AIS-Q454 Chapter 2 Hardware Installation Chapter 2 Hardware Installation 2-1
Ad va n c e d S y s t e m Controller 2.
Ad va n c e d S y s t e m Controller AIS-Q454 AIS-Q454 Chapter 2 Hardware Installation 2-3
Ad va n c e d S y s t e m Controller 2.
Ad va n c e d S y s t e m Controller AIS-Q454 AIS-Q454 Chapter 2 Hardware Installation 2-5
Ad va n c e d S y s t e m Controller AIS-Q454 2.3 List of Jumpers The board has a number of jumpers that allow you to configure your system to suit your application.
Ad va n c e d S y s t e m Controller AIS-Q454 2.4 List of Connectors The board has a number of connectors that allow you to configure your system to suit your application.
Ad va n c e d S y s t e m Controller AIS-Q454 2.5 Setting Jumpers You configure your card to match the needs of your application by setting jumpers. A jumper is the simplest kind of electric switch. It consists of two metal pins and a small metal clip (often protected by a plastic cover) that slides over the pins to connect them. To “close” a jumper you connect the pins with the clip. To “open” a jumper you remove the clip. Sometimes a jumper will have three pins, labeled 1, 2 and 3.
Ad va n c e d S y s t e m Controller AIS-Q454 2.6 Clear CMOS (JP1) JP1 Function 1-2 Clear CMOS 2-3 Normal (Default) 2.7 ME_TP1 TP1 Function Open Enable iAMT setup (Default) 1-2 Disable iAMT setup 2.8 Front Panel Connector (FP1) Pin Signal Pin Signal 1 Power On Button (+) 2 Reset Switch (+) 3 Power On Button (-) 4 Reset Switch (-) 5 IDE LED (+) 6 Power LED (+) 7 IDE LED (-) 8 Power LED (-) 2.
Ad va n c e d S y s t e m Controller AIS-Q454 5 USBD1+ 6 USBD2+ 7 GND 8 USBD2- 9 GND 10 +5V 2.11 CD-IN (J1) Pin Signal 1 CD-R 2 CD-GND 3 CD-GND 4 CD-L 2.12 RS232 Serial Port Connector (COM2) Pin Signal Pin Signal 1 DCD 2 RXD 3 TXD 4 DTR 5 GND 6 DSR 7 RTS 8 CTS 9 RI 10 N.C 2.13 Digital I/O (CN2) This connector offers 4-pair of digital I/O functions and address is 801H.
Ad va n c e d S y s t e m Controller AIS-Q454 The pin definitions and registers mapping are illustrated below: Address: 801H 4 in / 4 out Pin1 Pin2 Pin3 Pin4 Pin5 Pin6 Pin7 Pin8 GPI 27 GPI 25 GPI 24 GPO 23 GPO 22 GPO 21 GPO 20 GPI 26 MSB LSB 8 in Pin1 Pin2 Pin3 Pin4 Pin5 Pin6 Pin7 Pin8 GPI 27 GPI 26 GPI 25 GPI 24 GPI 23 GPI 22 GPI 21 GPI 20 MSB LSB 8 out Pin1 Pin2 Pin3 Pin4 Pin5 Pin6 Pin7 Pin8 GPO27 GPO 26 GPO25 GPO 24 GPO 23 GPO 22 GPO 21 GPO 20 MSB LSB
Ad va n c e d S y s t e m Controller AIS-Q454 2.15 List of Connectors of PER-R04X Label Function CN3 POWER Connector FAN1 FAN Connector SATA1 SATA Connector 2.16 Power Connector of PER-R04X (CN3) Pin Signal 1 GND 2 +3.3V 3 +3.3V 4 +3.3V 5 +5V 6 +12V 7 +12V 8 GND 2.17 FAN Connector of PER-R04X (FAN1) Pin Signal 1 GND 2 +12V 3 N.
Ad va n c e d S y s t e m Controller AIS-Q454 2.
Ad va n c e d S y s t e m Controller AIS-Q454 Step 3: Get the HDD ready and place the HDD to the HDD bracket Chapter 2 Hardware Installation 2-14
Ad va n c e d S y s t e m Controller AIS-Q454 Step 4: Fasten the two screws on the HDD bracket Step 5: Place the HDD back to the chassis Chapter 2 Hardware Installation 2-15
Ad va n c e d S y s t e m Controller AIS-Q454 Step 6: Fasten the two screws to lock the HDD bracket Step 7: Plug the SATA cable and power cable to the HDD Chapter 2 Hardware Installation 2-16
Ad va n c e d S y s t e m Controller AIS-Q454 Step 8: Close the upper HDD bracket to the HDD and fasten the screws to lock the HDD kit Chapter 2 Hardware Installation 2-17
Ad va n c e d S y s t e m Controller AIS-Q454 Step 9: Close and screw the case of the AIS-Q454 to finish the installation Chapter 2 Hardware Installation 2-18
Ad va n c e d S y s t e m Controller AIS-Q454 Chapter 3 Award BIOS Setup Chapter 3 Award BIOS Setup 3-1
Ad va n c e d S y s t e m Controller 3.1 AIS-Q454 System Test and Initialization These routines test and initialize board hardware. If the routines encounter an error during the tests, you will either hear a few short beeps or see an error message on the screen. There are two kinds of errors: fatal and non-fatal. The system can usually continue the boot up sequence with non-fatal errors.
Ad va n c e d S y s t e m Controller 3.2 AIS-Q454 Award BIOS Setup Awards BIOS ROM has a built-in Setup program that allows users to modify the basic system configuration. This type of information is stored in battery-backed CMOS RAM so that it retains the Setup information when the power is turned off. Entering Setup Power on the computer and press immediately. This will allow you to enter Setup. Standard CMOS Features Use this menu for basic system configuration. (Date, time, IDE, etc.
Ad va n c e d S y s t e m Controller AIS-Q454 PC Health Status This menu allows you to set the shutdown temperature for your system. Frequency/Voltage Control Use this menu to specify your settings for auto detect DIMM/PCI clock and spread spectrum. Load Fail-Safe Defaults Use this menu to load the BIOS default values for the minimal/stable performance for your system to operate.
Ad va n c e d S y s t e m Controller AIS-Q454 Chapter 4 Driver Installation Chapter 4 Driver Installation 4-1
Ad va n c e d S y s t e m Controller AIS-Q454 The AIS-Q454 comes with an AutoRun CD-ROM that contains all drivers and utilities that can help you to install the driver automatically. Insert the driver CD, the driver CD-title will auto start and show the installation guide. If not, please follow the sequence below to install the drivers.
Ad va n c e d S y s t e m Controller 4.1 AIS-Q454 Installation: Insert the AIS-Q454 CD-ROM into the CD-ROM drive and install the drivers from Step 1 to Step 4 in order. Step 1 – Install INF Driver 1. Click on the step 1-INF folder and double click on the Setup.exe 2. Follow the instructions that the window shows 3. The system will help you install the driver automatically Step 2 – Install VGA Driver 1. Click on the step 2 –VGA folder and select the OS your system is 2. Double click on .
Ad va n c e d S y s t e m Controller AIS-Q454 Step 4 – Install Audio Driver 1. Click on the step 4 –AUDIO folder and select the OS your system is 2. Double click on .exe file located in each OS folder 3. Follow the instructions that the window shows 4.
Ad va n c e d S y s t e m Controller AIS-Q454 Appendix A Programming the Watchdog Timer Appendix A Programming the Watchdog Timer A-1
Ad va n c e d S y s t e m Controller AIS-Q454 A.1 Programming AIS-Q454 utilizes ITE 8718 chipset as its watchdog timer controller. ( K version ) Below are the procedures to complete its configuration and the AAEON intial watchdog timer program is also attached based on which you can develop customized program to fit your application. Configuring Sequence Description After the hardware reset or power-on reset, the ITE 8718 enters the normal mode with all logical devices disabled except KBC.
Ad va n c e d S y s t e m Controller AIS-Q454 (1) Enter the MB PnP Mode To enter the MB PnP Mode, four special I/O write operations are to be performed during Wait for Key state. To ensure the initial state of the key-check logic, it is necessary to perform four write opera-tions to the Special Address port (2EH). Two different enter keys are provided to select configuration ports (2Eh/2Fh) of the next step.
Ad va n c e d S y s t e m Controller Bit 7-2 1 0 AIS-Q454 Description Reserved Returns to the Wait for Key state. This bit is used when the configuration sequence is completed. Resets all logical devices and restores configuration registers to their power-on states.
Ad va n c e d S y s t e m Controller AIS-Q454 WatchDog Timer Time-out Value (LSB) Register (Index=73h, Default=00h) Bit 7-0 Description WDT Time-out value 7-0 WatchDog Timer Time-out Value (MSB) Register (Index=74h, Default=00h) Bit 7-0 Description WDT Time-out value 15-8 A.2 ITE8718 Watchdog Timer Initial Program .MODEL SMALL .
Ad va n c e d S y s t e m Controller AIS-Q454 mov cl, 73h call Superio_Set_Reg ;Clear by keyboard or mouse interrupt mov al, 0f0h mov cl, 71h call Superio_Set_Reg ;unit is second.
Ad va n c e d S y s t e m Controller AIS-Q454 MOV AL,BYTE PTR CS:[SI] OUT DX,AL INC SI LOOP Init_1 RET Enter_Configuration_Mode ENDP Exit_Configuration_Mode PROC NEAR MOV AX,0202h CALL Write_Configuration_Data RET Exit_Configuration_Mode ENDP Check_Chip PROC NEAR MOV AL,20h CALL Read_Configuration_Data CMP AL,87h JNE Not_Initial MOV AL,21h CALL Read_Configuration_Data CMP AL,12h JNE Not_Initial Appendix A Programming the Watchdog Timer A-7
Ad va n c e d S y s t e m Controller AIS-Q454 Need_Initial: STC RET Not_Initial: CLC RET Check_Chip ENDP Read_Configuration_Data PROC NEAR MOV DX,WORD PTR CS:[Cfg_Port+04h] OUT DX,AL MOV DX,WORD PTR CS:[Cfg_Port+06h] IN AL,DX RET Read_Configuration_Data ENDP Write_Configuration_Data PROC NEAR MOV DX,WORD PTR CS:[Cfg_Port+04h] OUT DX,AL XCHG AL,AH MOV DX,WORD PTR CS:[Cfg_Port+06h] OUT DX,AL RET Write_Configuration_Data ENDP Superio_Set_Reg proc near Appendix A Programming the Watchdog Timer A-8
Ad va n c e d S y s t e m Controller AIS-Q454 push ax MOV DX,WORD PTR CS:[Cfg_Port+04h] mov al,cl out dx,al pop ax inc dx out dx,al ret Superio_Set_Reg endp.
Ad va n c e d S y s t e m Controller END Main Note: Interrupt level mapping 0Fh-Dh: not valid 0Ch: IRQ12 . .
Ad va n c e d S y s t e m Controller AIS-Q454 Appendix B I/O Information Appendix B I/O Information B-1
Ad va n c e d S y s t e m Controller B.
Ad va n c e d S y s t e m Controller AIS-Q454 B.
Ad va n c e d S y s t e m Controller B.3 IRQ Mapping Chart B.
