Mini-ITX EMB-A70M EMB-A70M AMD R-460L(Quad-core)/ R-260H (Dual-core) APU Mini-ITX 2 Realtek 8111E Ethernet 2 USB3.0, 5 USB2.
Mini-ITX EMB-A70M Copyright Notice This document is copyrighted, 2013. All rights are reserved. The original manufacturer reserves the right to make improvements to the products described in this manual at any time without notice. No part of this manual may be reproduced, copied, translated, or transmitted in any form or by any means without the prior written permission of the original manufacturer. Information provided in this manual is intended to be accurate and reliable.
Mini-ITX EMB-A70M Acknowledgments All other products’ name or trademarks are properties of their respective owners. Award is a trademark of Award Software International, Inc. CompactFlash™ is a trademark of the Compact Flash Association. AMD, the AMD Arrow logo and combinations thereof are trademarks of Advanced Micro Devices, Inc. Microsoft Windows® is a registered trademark of Microsoft Corporation. ITE is a trademark of Integrated Technology Express, Inc.
Mini-ITX EMB-A70M Packing List (Standard, not bulk pack) Before you begin installing your card, please make sure that the following materials have been shipped: 1 9657666600 Jumper Kit 1 1709070800 SATA Cable 1 1702151201 SATA Power CABLE 1 M20A70M000 I/O Shield 1 17592A70M1 CPU Cooler 1 Utility DVD 1 EMB-A70M If any of these items should be missing or damaged, please contact your distributor or sales representative immediately.
Mini-ITX EMB-A70M Contents Chapter 1 General Information 1.1 Introduction................................................................ 1-2 1.2 Features .................................................................... 1-3 1.3 Specifications ............................................................ 1-4 Chapter 2 Quick Installation Guide 2.1 Safety Precautions .................................................. 2-2 2.2 Location of Connectors and Jumpers ...................... 2-3 2.
Mini-ITX Chapter 3 EMB-A70M AMI BIOS Setup 3.1 System Test and Initialization. .................................. 3-2 3.2 AMI BIOS Setup ........................................................ 3-3 Chapter 4 Driver Installation 4.1 Installation………………………………………..……..4-3 Appendix A Programming The Watchdog Timer A.1 Watchdog Timer Initial Program ...............................A-2 Appendix B I/O Information B.1 I/O Address Map .......................................................B-2 B.
Mini-ITX EMB-A70M Chapter 1 General Information Chapter 1 General Information 1- 1
Mini-ITX EMB-A70M 1.1 Introduction The EMB-A70M supports AMD Embedded R-460L (Quad-core)/ R-260H (Dual-core) APU processor which paired with the AMD Hudson M3/A70M chipset offers a high performance computing platform with low power consumption. This new product supports two DDR3 SODIMMs at speeds of 1333/1066 MHz, up to 8 GB. Two SATA interfaces provide ample storage. With dual Gigabit Ethernet, two COM ports, five USB2.0 ports, two USB3.
Mini-ITX EMB-A70M 1.2 Features AMD R-Series APU FP2 Processor AMD Hudson M3/A70M 204-pin SODIMM x 2 DDR3 1333/1066MHz up to 8 GB Realtek 8111E for Gigabit LAN, RJ-45 x 2 Supporting Static Full HD display by HDMI x 4 (Note: 1. Minimum of 3 identical monitors for 4 independent display. 2. Static playback could support 4 independent displays up to FHD 1080P.) SATA 6.0Gb/s x 2, mSATA x 1 USB 2.0 x 1 with Type A Connectors; USB 3.0 x 2, USB 2.
Mini-ITX EMB-A70M 1.3 Specifications System Processor AMD R-260H (Dual-core) and System Memory optional R-460L (Quad core) APU 2 x SoDIMM, DDR3 1333/1066 Non-ECC,Un-buffered Memory, Max. 8GB Chipset AMD® Hudson M3/ A70M I/O Chipset ITE IT8728 Ethernet LAN1: Realtek® 8111E PCIe Gigabit LAN controller, RJ-45 X1 LAN2: Realtek® 8111E PCIe Gigabit LAN controller, RJ-45 X1 BIOS 32 Mb Flash ROM , AMI BIOS, PnP, DMI 2.0, WfM 2.0, ACPI 2.0a, SM BIOS 2.
Mini-ITX EMB-A70M Battery Lithium battery Power Requirement 2 x 2pin 12V ATX connector, 1 x CPU fan with 4-pin wafer 1 x System fan with 4-pin wafer, 1 x SATA power with 4-pin wafer, 1x power button switch (optional reserve) Board Size 6.7”(L) x 6.7”(W) (170 mm x 170 mm) Gross Weight 1.1 lb (0.
Mini-ITX EMB-A70M Audio Mic-in x 1, Line-out x 1 (on Rear I/O) USB USB 2.0 x 1 with Type A Connectors; USB 3.0 x 2, USB 2.
Mini-ITX EMB-A70M Chapter 2 Quick Installation Guide Chapter 2 Quick Installation Guide 2 - 1
Mini-ITX EMB-A70M 2.1 Safety Precautions Always completely disconnect the power cord from your board whenever you are working on it. Do not make connections while the power is on, because a sudden rush of power can damage sensitive electronic components. Always ground yourself to remove any static charge before touching the board. Modern electronic devices are very sensitive to static electric charges. Use a grounding wrist strap at all times.
Mini-ITX EMB-A70M 2.
Mini-ITX Solder Side Chapter 2 Quick Installation Guide 2 - 4 EMB-A70M
Mini-ITX EMB-A70M 2.
Mini-ITX Solder Side Chapter 2 Quick Installation Guide 2 - 6 EMB-A70M
Mini-ITX EMB-A70M 2.4 List of Jumpers The board has a number of jumpers that allow you to configure your system to suit your application. The table below shows the function of each of the board's jumpers: Label Function CN8 Auto Power Button Selection CN9 COM1 RI Power Selection CN22 CMOS Setting Selection 2.5 List of Connectors The board has a number of connectors that allow you to configure your system to suit your application.
Mini-ITX EMB-A70M CN12 KB/MS Pin Header CN14 CPU FAN Connector CN15 CPU FAN Connector (Optional) CN16 SATA Signal Connector CN17 SATA Signal Connector CN18 SATA Power Connector CN19 Dual USB3.0 Box Header CN20 Dual USB2.0 Box Header CN21 Dual USB2.
Mini-ITX EMB-A70M 2.6 Setting Jumpers You configure your card to match the needs of your application by setting jumpers. A jumper is the simplest kind of electric switch. It consists of two metal pins and a small metal clip (often protected by a plastic cover) that slides over the pins to connect them. To “close” a jumper you connect the pins with the clip. To “open” a jumper you remove the clip. Sometimes a jumper will have three pins, labeled 1, 2 and 3.
Mini-ITX EMB-A70M 2.7 Auto Power Button Setting (CN8) JP1 Function 1-2 Normal (Default) 2-3 Auto Button 2.8 COM1 RI Power Selection (CN9) JP1 Function 1-2 12V 3-4 Normal (Default) 5-6 5V 2.9 CMOS Setting (CN22) JP1 Function 1-2 Normal (Default) 2-3 Clear CMOS 2.
Mini-ITX EMB-A70M 7 GND 8 USBD2- 9 GND 10 +5V 4 A_JD_FRONT 8 NA 5 LINE2_L 10 LINE IN SENSOR resister 2.12 RS232 /422/485 Pin Header (COM1) Pin Signal Pin Signal 1 DCD 2 RXD 3 TXD 4 DTR 5 GND 6 DSR 7 RTS 8 CTS 9 RI 10 N.C Signal Pin Signal 1 DIO1 2 DIO2 3 DIO3 4 DIO4 5 DIO5 6 DIO6 7 DIO7 8 DIO8 9 +3.3V 10 GND Signal Pin Signal 1 GND 2 +12V 3 FAN_TAC 2.13 Digital I/O Pin Header (DIO1) Pin 2.14 FAN Connector Pin FAN_CTL 2.
Mini-ITX 3 +12V EMB-A70M 4 +12V 2.16 SATA Connector (SATA 1~5) Pin Signal Pin Signal 1 GND 2 TXP 3 TXN 4 GND 5 RXN 6 RXP 7 GND 2.17 USB3.
Mini-ITX EMB-A70M Below Table for China RoHS Requirements 产品中有毒有害物质或元素名称及含量 AAEON Main Board/ Daughter Board/ Backplane 有毒有害物质或元素 部件名称 铅 汞 镉 六价铬 多溴联苯 多溴二苯醚 (Pb) (Hg) (Cd) (Cr(VI)) (PBB) (PBDE) × ○ ○ ○ ○ ○ × ○ ○ ○ ○ ○ 印刷电路板 及其电子组件 外部信号 连接器及线材 O：表示该有毒有害物质在该部件所有均质材料中的含量均在 SJ/T 11363-2006 标准规定的限量要求以下。 X：表示该有毒有害物质至少在该部件的某一均质材料中的含量超出 SJ/T 11363-2006 标准规定的限量要求。 备注：此产品所标示之环保使用期限，系指在一般正常使用状况下。 Chapter 2 Quick Installation Guide 2 - 13
Mini-ITX EMB-A70M Chapter 3 AMI BIOS Setup Chapter 3 AMI BIOS Setup 3-1
Mini-ITX EMB-A70M 3.1 System Test and Iinitialization These routines test and initialize board hardware. If the routines encounter an error during the tests, you will either hear a few short beeps or see an error message on the screen. There are two kinds of errors: fatal and non-fatal. The system can usually continue the boot up sequence with non-fatal errors. System configuration verification These routines check the current system configuration stored in the CMOS memory and BIOS NVRAM.
Mini-ITX EMB-A70M 3.2 AMI BIOS Setup AMI BIOS ROM has a built-in Setup program that allows users to modify the basic system configuration. This type of information is stored in battery-backed CMOS RAM and BIOS NVRAM so that it retains the Setup information when the power is turned off. Entering Setup Power on the computer and press or immediately. This will allow you to enter Setup. Main Set the date, use tab to switch between date elements.
Mini-ITX EMB-A70M Setup Menu Setup submenu: Main Chapter 3 AMI BIOS Setup 3-4
Mini-ITX EMB-A70M Setup submenu: Advanced Chapter 3 AMI BIOS Setup 3-5
Mini-ITX EMB-A70M ACPI Settings Options summary: ACPI Sleep State S3 only (Suspend to RAM) Select the ACPI state used for System Suspend Chapter 3 AMI BIOS Setup 3-6 Optimal Default, Failsafe Default
Mini-ITX EMB-A70M CPU Configuration Chapter 3 AMI BIOS Setup 3-7
Mini-ITX EMB-A70M IDE Configuration (IDE) Options summary: OnChip SATA Type RAID AHCI Legacy IDE Chapter 3 AMI BIOS Setup 3-8 Optimal Default, Failsafe Default
Mini-ITX EMB-A70M USB Configuration Options summary: Legacy USB Support Enabled Optimal Default, Failsafe Default Disabled Auto Enables BIOS Support for Legacy USB Support. When enabled, USB can be functional in legacy environment like DOS. AUTO option disables legacy support if no USB devices are connected Device Name (Emulation Auto Optimal Default, Failsafe Default Type) Floppy Forced FDD Hard Disk CDROM If Auto.
Mini-ITX EMB-A70M Super IO Configuration Chapter 3 AMI BIOS Setup 3-10
Mini-ITX EMB-A70M Serial Port 1 Configuration Options summary: Serial Port Disabled Enabled Optimal Default, Failsafe Default Allows BIOS to En/Disable correspond serial port. Change Settings Auto Optimal Default, Failsafe Default IO=3F8h;IRQ=4; IO=2F8h;IRQ=3; Allows BIOS to Select Serial Port resource.
Mini-ITX EMB-A70M Serial Port 2 Configuration Options summary: Serial Port Disabled Enabled Optimal Default, Failsafe Default Allows BIOS to En/Disable correspond serial port. Change Settings Auto Optimal Default, Failsafe Default IO=3F8h;IRQ=4; IO=2F8h;IRQ=3; Allows BIOS to Select Serial Port resource.
Mini-ITX EMB-A70M H/W Monitor Chapter 3 AMI BIOS Setup 3-13
Mini-ITX EMB-A70M Smart Fan Mode Configuration (Manual Mode) Options Summary : CPU Fan Control Disabled (SYS Fan Control) Enabled Default For En/Disable CPU(SYS) Fan1 Control Enabled: Fan is running in accordance with user settings Disabled: Fan is always running with full speed Fan Control Mode Manual Mode Default Automatic Mode Manual Mode: Depends on PWM Duty Automatic Mode: Fan Speed is depends on CPU Temperature PWM Duty 200 Default 0~255 Manual Mode PWM Duty value Chapter 3 AMI BIOS Setup 3-14
Mini-ITX EMB-A70M Smart Fan Mode Configuration (Thermal Cruise Mode) Options Summary : Spin PWM 100 Default 255 The PWM Duty of Fan Spin Off Control 30 Default Temperature Temperature Limit Value of Fan Off.
Mini-ITX EMB-A70M Dynamic Digital IO Options summary: GPI0~GPI3 Input Direction Output Set GPIO as Input or Output GPO0~GPI3 Input Direction Output Set GPIO as Input or Output Output Level Hi Low Set GPIO Output as Hi or Low Chapter 3 AMI BIOS Setup 3-16 Optimal Default, Failsafe Default Optimal Default, Failsafe Default Optimal Default, Failsafe Default
Mini-ITX EMB-A70M Trusted Computing Options summary: Security Device Disabled Optimal Default, Failsafe Default Support Enabled Enable/Disable Security Device. NOTE: Your Computer will reboot during restart in order to change State of the Device.
Mini-ITX EMB-A70M Power Management Options summary: Power Mode ATX Type AT Type Select power supply mode.
Mini-ITX EMB-A70M S5 RTC Wake Settings (Fixed Time) Options summary: Wake system with Disabled Optimal Default, Failsafe Default Fixed Time Enabled En/Disable System wake on alarm event. When enabled, System will wake on the hr:min:sec specified Wake up day 0-31 Default 0 Select 0 for daily system wake up, 1-31 for witch day of the moth that you would like the system to wake up.
Mini-ITX EMB-A70M S5 RTC Wake Settings (Dynamic Time) Options summary: Wake system with Disabled Optimal Default, Failsafe Default Dynamic Time Enabled En/Disable System wake on alarm event.
Mini-ITX EMB-A70M Setup submenu: Chipset Chapter 3 AMI BIOS Setup 3-21
Mini-ITX EMB-A70M HOST Bridge Chapter 3 AMI BIOS Setup 3-22
Mini-ITX EMB-A70M South Bridge Options summary: HD Audio Azalia Device Auto Disabled Optimal Default, Failsafe Default Enabled Control Detection of the Azalia device.\n\nDisabled = Azalia will be unconditionally disabled\n\nEnabled = Azalia will be unconditionally Enabled GPP Port Link x4 mode Configuration 2:2 mode 2:1:1 mode Optimal Default, Failsafe Default 1:1:1:1 mode GPP Port mode selection. GPP Gen2 Disabled Enabled Optimal Default, Failsafe Default GPP Port link speed.
Mini-ITX EMB-A70M Setup submenu: Boot Chapter 3 AMI BIOS Setup 3-24
Mini-ITX EMB-A70M Options summary: Bootup NumLock State On Default Off Select the keyboard NumLock state Quiet Boot Disabled Enabled Default En/Disable showing boot logo. Launch I82579LM PXE Disabled Default OpROM Enabled En/Disable Legacy Boot Option for I82579LM. Launch I82583V PXE Disabled Default OpROM Enabled En/Disable Legacy Boot Option for I82583V. Option ROM Messages Force BIOS Default Keep Current Set display mode for Option ROM.
Mini-ITX EMB-A70M BBS Priorities Chapter 3 AMI BIOS Setup 3-26
Mini-ITX EMB-A70M Security Change User/Supervisor Password You can install a Supervisor password, and if you install a supervisor password, you can then install a user password. A user password does not provide access to many of the features in the Setup utility. If you highlight these items and press Enter, a dialog box appears which lets you enter a password. You can enter no more than six letters or numbers. Press Enter after you have typed in the password.
Mini-ITX EMB-A70M Setup submenu: Exit Chapter 3 AMI BIOS Setup 3-28
Mini-ITX EMB-A70M Chapter 4 Driver Installation .
Mini-ITX EMB-A70M The EMB-A70M comes with an Autorun DVD-ROM that contains all drivers and utilities that can help you to install the driver automatically. Insert the driver DVD, the driver DVD-title will automatically start and show the installation guide. If not, please follow the sequence below to install the drivers.
Mini-ITX 4.1 EMB-A70M Installation: Insert the EMB-A70M DVD-ROM into the DVD-ROM drive. And install the drivers from Step 1 to Step 6 in order. Step 1 – Install Chipset & VGA Driver 1. Click on the Step 1 - Chipset & VGA folder and select the OS folder your system is 2. Double click on theSetup.exe file 3. Follow the instructions that the window shows 4.
Mini-ITX EMB-A70M 3. Follow the instructions that the window shows 4. The system will help you install the driver automatically Step 5 – Install TPM Driver 1. Click on the STEP5-TPM folder and select the OS folder your system is 2. Double click on the Setup.exe file located in each OS folder 3. Follow the instructions that the window shows 4. The system will help you install the driver automatically Step 6 – Install Serial Port Driver (Optional) For Windows® XP: 1.
Mini-ITX EMB-A70M 2.
Mini-ITX EMB-A70M 3. Reboot and Administrator login. 4. To run patch.bat with [Run as administrator].
Mini-ITX EMB-A70M Appendix A Programming the Watchdog Timer Appendix A Programming the Watchdog Timer A-1
Mini-ITX EMB-A70M A.1 Watchdog Timer Initial Program Table 1 : SuperIO relative register table Default Value Index 0x2E(Note1) Data 0x2F(Note2) Note SIO MB PnP Mode Index Register 0x2E or 0x4E SIO MB PnP Mode Data Register 0x2F or 0x4F Table 2 : Watchdog relative register table LDN Register BitNum Value Note Time of watchdog timer Timer Counter 0x07(Note3) 0x73(Note4) (Note24) (0~255) This register is byte access Select time unit.
Mini-ITX EMB-A70M ************************************************************************************ // SuperIO relative definition (Please reference to Table 1) #define byte SIOIndex #define byte SIOData //This parameter is represented from Note1 //This parameter is represented from Note2 #define void IOWriteByte(byte IOPort, byte Value); #define byte IOReadByte(byte IOPort); // Watch Dog relative definition (Please reference to Table 2) #define byte TimerLDN //This parameter is represente
Mini-ITX EMB-A70M ************************************************************************************ VOID Main(){ // Procedure : AaeonWDTConfig // (byte)Timer : Time of WDT timer.(0x00~0xFF) // (boolean)Unit : Select time unit(0: second, 1: minute). AaeonWDTConfig(); // Procedure : AaeonWDTEnable // This procudure will enable the WDT counting.
Mini-ITX EMB-A70M ************************************************************************************ // Procedure : AaeonWDTEnable VOID AaeonWDTEnable (){ WDTEnableDisable(EnableLDN, EnableReg, EnableBit, 1); } // Procedure : AaeonWDTConfig VOID AaeonWDTConfig (){ // Disable WDT counting WDTEnableDisable(EnableLDN, EnableReg, EnableBit, 0); // Clear Watchdog Timeout Status WDTClearTimeoutStatus(); // WDT relative parameter setting WDTParameterSetting(); } VOID WDTEnableDisable(byte LDN, byte Regist
Mini-ITX EMB-A70M ************************************************************************************ VOID SIOEnterMBPnPMode(){ Switch(SIOIndex){ Case 0x2E: IOWriteByte(SIOIndex, 0x87); IOWriteByte(SIOIndex, 0x01); IOWriteByte(SIOIndex, 0x55); IOWriteByte(SIOIndex, 0x55); Break; Case 0x4E: IOWriteByte(SIOIndex, 0x87); IOWriteByte(SIOIndex, 0x01); IOWriteByte(SIOIndex, 0x55); IOWriteByte(SIOIndex, 0xAA); Break; } } VOID SIOExitMBPnPMode(){ IOWriteByte(SIOIndex, 0x02); IOWriteByte(SIOData, 0x02); } VOI
Mini-ITX EMB-A70M ************************************************************************************ VOID SIOBitSet(byte LDN, byte Register, byte BitNum, byte Value){ Byte TmpValue; SIOEnterMBPnPMode(); SIOSelectLDN(byte LDN); IOWriteByte(SIOIndex, Register); TmpValue = IOReadByte(SIOData); TmpValue &= ~(1 << BitNum); TmpValue |= (Value << BitNum); IOWriteByte(SIOData, TmpValue); SIOExitMBPnPMode(); } VOID SIOByteSet(byte LDN, byte Register, byte Value){ SIOEnterMBPnPMode(); SIOSelectLDN(LDN); IOWrit
Mini-ITX EMB-A70M Appendix B I/O Information Appendix B I/O Information B-1
Mini-ITX B.
Mini-ITX EMB-A70M Appendix B I/O Information B-3
Mini-ITX Appendix B I/O Information B-4 EMB-A70M
Mini-ITX EMB-A70M B.
Mini-ITX B.
Mini-ITX EMB-A70M Appendix B I/O Information B-7
Mini-ITX Appendix B I/O Information B-8 EMB-A70M
Mini-ITX EMB-A70M Appendix B I/O Information B-9
Mini-ITX B.
Mini-ITX EMB-A70M Appendix C Mating Connecotor Appendix C Mating Connector C - 1
Mini-ITX EMB-A70M C.1 List of Mating Connectors and Cables The table notes mating connectors and available cables. Connector Label CN32 CN33 CN34 CN28 CN29 CN30 CN31 CN4 CN5 CN10 CN11 CN35 Function Mating Connector Vendor Model no USB HO-BASE.
Mini-ITX CN35 LINE OUT Connector TACT CN20 USB Connector CATCH CN21 USB Connector CATCH CN19 CN16 CN17 CN12 CN2 CN18 USB3.0 Connector SATA Connector SATA Connector PS2 Connector FAN Connector POWER Connector PINREX TECHB EST TECHB EST 凱迅 CATCH 何迪 EMB-A70M C1F2R1-570 -R 2.00mm Pitch 10 pins ( CATCH H754-2x5 or compatible) 2.
Mini-ITX EMB-A70M Appendix D Programming the Digital I/O Appendix D Electrical Specifications for I/O Ports D-1
Mini-ITX EMB-A70M D.1 DIO Programming EMB-A70M utilizes ITE8728 chipset as its Digital I/O controller. Below are the procedures to complete its configuration which you can develop customized program to fit your application.
Mini-ITX EMB-A70M D.
Mini-ITX EMB-A70M D.
Mini-ITX EMB-A70M ************************************************************************************ VOID Main(){ Boolean PinStatus ; // Procedure : AaeonReadPinStatus // Input : // Example, Read Digital I/O Pin 3 status // Output : // InputStatus : // 0: Digital I/O Pin level is low // 1: Digital I/O Pin level is High PinStatus = AaeonReadPinStatus(DIO3Reg, DIO3Bit); // Procedure : AaeonSetOutputLevel // Input : // Example, Set Digital I/O Pin 6 level AaeonSetOutputLevel(DIO6Reg, DIO6Bit, DI
Mini-ITX EMB-A70M ************************************************************************************ Boolean AaeonReadPinStatus(byte Register, byte BitNum){ Boolean PinStatus ; PinStatus = DIOBitRead(Register, BitNum); Return PinStatus ; } VOID AaeonSetOutputLevel(byte Register, byte BitNum, byte Value){ DIOBitSet(Register, BitNum, Value); } Boolean DIOBitRead(byte Register, byte BitNum){ Byte TmpValue; TmpValue = IOReadByte(Register); TmpValue &= (1 << BitNum); If(TmpValue == 0) Return 0; Return 1
Mini-ITX EMB-A70M Appendix E AHCI Setting Appendix E AHCI Setting E-1
Mini-ITX EMB-A70M E.1 Setting AHCI OS installation to setup AHCI Mode Step 1: Copy the files below from “Driver CD ->Step 2 – AHCI_RAID -> Floppy -> WinXP -> 3.3.1540.
Mini-ITX EMB-A70M Step 3: The setting procedures “ In BIOS Setup Menu” A: Advanced -> SATA Configuration -> SATA Configuration -> SATA Mode -> AHCI Mode Step 4: The setting procedures “In BIOS Setup Menu” B: Boot -> Boot Option #1 -> DVD-ROM Type Appendix E AHCI Setting E-3
Mini-ITX EMB-A70M Step 5: The setting procedures “In BIOS Setup Menu” C: Save & Exit -> Save Changes and Exit Step 6: Setup OS Appendix E AHCI Setting E-4
Mini-ITX EMB-A70M Step 7: Press “F6” Step 8: Choose “S” Appendix E AHCI Setting E-5
Mini-ITX EMB-A70M Step 9: Choose “Intel(R) 5 Series 6 Port SATA AHCI Controller” Step 10: It will show the model number you select and then press “ENTER” Appendix E AHCI Setting E-6
Mini-ITX EMB-A70M Step 11: Setup is loading files Appendix E AHCI Setting E-7
