Industrial Motherboard EMB-CV1 series EMB-CV1 series Manual 2nd Ed.
Industrial Motherboard EMB-CV1 series Copyright Notice This document is copyrighted, 2013. All rights are reserved. The original manufacturer reserves the right to make improvements to the products described in this manual at any time without notice. No part of this manual may be reproduced, copied, translated, or transmitted in any form or by any means without the prior written permission of the original manufacturer. Information provided in this manual is intended to be accurate and reliable.
Industrial Motherboard EMB-CV1 series Acknowledgments All other products’ name or trademarks are properties of their respective owners. AMI is a trademark of American Megatrends Inc. CompactFlash™ is a trademark of the Compact Flash Association. Intel® and Atom™ are trademarks of Intel® Corporation. Microsoft Windows® is a registered trademark of Microsoft Corporation. ITE is a trademark of Integrated Technology Express, Inc.
Industrial Motherboard EMB-CV1 series Packing List (Standard, not bulk pack) Before you begin installing your card, please make sure that the following materials have been shipped: 1 Cable Set (SATA Cable, SATA Power Cable) 1 Metal I/O Bracket 1 Product CD 1 Industrial Motherboard If any of these items should be missing or damaged, please contact your distributor or sales representative immediately.
Industrial Motherboard EMB-CV1 series Contents Chapter 1 General Information 1.1 Features .................................................................... 1-2 1.2 Specifications ............................................................ 1-3 Chapter 2 Quick Installation Guide 2.1 Safety Precautions .................................................. 2-2 2.2 Location of Connectors and Jumpers ...................... 2-3 2.3 Mechanical Drawing ................................................ 2-4 2.
Industrial Motherboard EMB-CV1 series 2.15 +12V AUX Power Connector (CON2) ................... 2-11 2.16 CPU/SYSTEM FAN Connector (CPU_FAN/CHA_FAN) ....................................................................................... 2-11 2.17 COM3/COM4/COM5 RS232 Serial Port PIN HEADER (COM3/COM4/COM5) ................................................... 2-12 2.18 GPIO/SM BUS/COM2/ COM2 External Power Selection (DIGITALREFENCE) ..................................... 2-12 2.
Industrial Motherboard EMB-CV1 series Appendix A Programming The Watchdog Timer A.1 Programming ........................................................... .A-2 A.2 ITE8783 Watchdog Timer Initial Program .………....A-6 Appendix B Mating Connector B.1 List of Mating Connectors and Cables ..................... .
Industrial Motherboard EMB-CV1 series Chapter 1 General Information Chapter 1 General Information 1- 1
Industrial Motherboard EMB-CV1 series 1.1 Features ® Onboard Intel Atom™ D2550 Processor Intel NM10 Intel Graphics Media Accelerator 3600 Supports DirectX ® ® 10, OpenGL 3.0 DDR3 800/1066 SO-DIMM x 2, Max. 4GB VGA, 18/24-bit LVDS, DVI, Dual Independent Display Dual Gigabit Ethernet COM x 5 (RS-232 x 4, RS-232/422/485 x 1) USB2.
Industrial Motherboard EMB-CV1 series 1.2 Specifications System Processor ® Intel Atom™ D2550 Dual Core Processor, up to 1.86GHz System Memory 204-pin single channel DDR3 800/1066 DIMM x 2, Max.
Industrial Motherboard EMB-CV1 series Operating Temperature 32˚F~ 140˚F (0˚C ~ 60˚C) Storage Temperature -40˚F~ 185˚F (-40˚C ~ 85˚C) Operating Humidity 5%~95% relative humidity, non-condensing Display Chipset ® Intel Graphics Media Accelerator 3650 Resolution Up to 1440x900 18/24-bit LCD Interface 18/24-bit LVDS Video Interface VGA x 1, DVI-D x 1 Storage SATA x 2 (support AHCI mode) I/O (if use m-SATA, one SATA port will be disable) Serial Port RS-232 x 4, RS-232
Industrial Motherboard EMB-CV1 series Chapter 2 Quick Installation Guide Chapter 2 Quick Installation Guide 2 - 1
Industrial Motherboard 2.1 EMB-CV1 series Safety Precautions Always completely disconnect the power cord from your board whenever you are working on it. Do not make connections while the power is on, because a sudden rush of power can damage sensitive electronic components. Always ground yourself to remove any static charge before touching the board. Modern electronic devices are very sensitive to static electric charges. Use a grounding wrist strap at all times.
Industrial Motherboard 2.2 EMB-CV1 series Location of Connectors and Jumpers NOTE: If choose m-SATA SKU, SATA3G_2 port, mini card and SIM card slot will be disable.
Industrial Motherboard 2.
Industrial Motherboard EMB-CV1 series Solder Side Chapter 2 Quick Installation Guide 2 - 5
Industrial Motherboard 2.4 EMB-CV1 series List of Jumpers The board has a number of jumpers that allow you to configure your system to suit your application.
Industrial Motherboard 2.5 EMB-CV1 series List of Connectors The board has a number of connectors that allow you to configure your system to suit your application.
Industrial Motherboard EMB-CV1 series USB56 USB 5 & 6 Pin Header USB7 USB 7 Pin Header WLAN Mini PCI-E Slot NOTE: The +12V Power connector (Label: DC_PWR) is lockable Jack type with screw. Please refer the inner and outer diameter dimension of connector as below to choose suitable adaptor.
Industrial Motherboard 2.6 EMB-CV1 series Setting Jumpers You configure your card to match the needs of your application by setting jumpers. A jumper is the simplest kind of electric switch. It consists of two metal pins and a small metal clip (often protected by a plastic cover) that slides over the pins to connect them. To “close” a jumper you connect the pins with the clip. To “open” a jumper you remove the clip. Sometimes a jumper will have three pins, labeled 1, 2 and 3.
Industrial Motherboard 2.7 2.8 2.9 EMB-CV1 series AT/ATX Mode Selection (ATMODE) ATOMODE Function Close 1-2 AT Close 2-3 ATX Mode (Default) Clear COMS (CLRTC) CLRTC Function Close 1-2 Protected (Default) Close 2-3 Clear COM2 External Power Selection (DIGITALREFENCE) DIGITALREFENCE Function Close 15-16 +12V Close 17-18 RI# (Default) Close 19-20 +5V 2.10 LVDS Panel Power Selection (LVDS_VDD_SEL) LVDS_VDD_SEL Function Close 1-2 +3.3V (Default) Close 2-3 +5V 2.
Industrial Motherboard EMB-CV1 series 2.12 LVDS function Enable (LVDS_SWITCH) LVDS_SWITCH Function Close 1-2 Disable Close 2-3 Enable (Default) 2.13 LVDS Panel Backlight Power Selection (LCD_POWER_SEL) LCD_POWER_SEL Function Close 1-2 +12V Close 2-3 +5V (Default) 2.14 Watchdog Timer Function Switch (WDT) WDT Function Close 1-2 Disable (Default) Close 2-3 Enable 2.15 +12V AUX Power Connector (CON2) Pin Signal Pin Signal 1 GND 2 GND 3 +12V 4 +12V 2.
Industrial Motherboard EMB-CV1 series 2.17 COM3/COM4/COM5 RS-232 Serial Port PIN HEADER (COM3/COM4/COM5) Pin Signal Pin Signal 1 DCD 2 RXD 3 TXD 4 DTR 5 GND 6 DSR 7 RTS 8 CTS 9 RI 10 NC 2.
Industrial Motherboard EMB-CV1 series 2.19 COM2 RS-232/422/485 connector Pin Signal Pin Signal 1 DCD (422TXD-/485DATA-) 2 RXD (422RXD+) 3 TXD (422TXD+/485DATA+) 4 DTR (422RXD-) 5 GND 6 DSR 7 RTS 8 CTS 9 RI/+12V/+5V 10 N.C. 2.20 Front Panel Pin Header (F_PANEL) Pin Signal Pin Signal 1 HDDLED+ 2 POWERLED+ 3 HDDLED- 4 POWERLED- 5 RESET- 6 PWRBTN+ 7 RESET+ 8 PWRBTN- 9 N/C 2.
Industrial Motherboard EMB-CV1 series 2.22 LVDS Panel Power Connector (LCD_POWER) Pin Signal Pin Signal 1 Panel Power 2 Panel brightness control 3 GND 4 GND 5 Panel backlight control 2.
Industrial Motherboard EMB-CV1 series 2.24 LVDS Panel Connector (LVDS) Pin Signal Pin Signal 1 NC 2 NC 3 Panel power 4 GND 5 NC 6 NC 7 NC 8 NC 9 NC 10 NC 11 NC 12 NC 13 DDC_DATA 14 DDC_CLOCK 15 DATA3- 16 DATA3+ 17 DATA2- 18 DATA2+ 19 DATA1- 20 DATA1+ 21 DATA0- 22 DATA0+ 23 Panel power 24 GND 25 LVDS_CLOCK- 26 LVDS_CLOCK+ 27 Panel power 28 GND 29 Backlight enable 30 Brightness control NOTE: LVDS connector Vendor: PINREX; Model: 712-76-30GWR8.
Industrial Motherboard Audio LAN EMB-CV1 series VGA DVI-D LAN 1 29 30 2 2.25 Serial ATA Power Connector (SATA_PWR1) Pin Signal Pin Signal 1 +5 2 GND 3 GND 4 +12V 2.
Industrial Motherboard EMB-CV1 series 2.
Industrial Motherboard EMB-CV1 series Chapter 3 AMI BIOS Setup Chapter 3 AMI BIOS Setup 3-1
Industrial Motherboa rd 3.1 EMB-CV1 series System Test and Initialization These routines test and initialize board hardware. If the routines encounter an error during the tests, you will either hear a few short beeps or see an error message on the screen. There are two kinds of errors: fatal and non-fatal. The system can usually continue the boot up sequence with non-fatal errors.
Industrial Motherboard 3.2 EMB-CV1 series AMI BIOS Setup AMI BIOS ROM has a built-in Setup program that allows users to modify the basic system configuration. This type of information is stored in battery-backed CMOS RAM so that it retains the Setup information when the power is turned off. Entering Setup Power on the computer and press or immediately. This will allow you to enter Setup. Main Set the date, use tab to switch between date elements.
Industrial Motherboard EMB-CV1 series Chapter 4 Driver Installation 0B .
Industrial Motherboard EMB-CV1 series The EMB-CV1 comes with an Autorun CD-ROM that contains all drivers and utilities that can help you to install the driver automatically. Insert the driver CD, the driver CD-title will automatically start and show the installation guide. If not, please follow the sequence below to install the drivers.
Industrial Motherboard 4.1 EMB-CV1 series Installation: Insert the EMB-CV1 CD-ROM into the CD-ROM drive. And install the drivers from Step 1 to Step 5 in order. Step 1 – Install Chipset Driver 1. Click on the Step1-INF folder and double click on the Setup.exe 2. Follow the instructions that the window shows 3. The system will help you install the driver automatically Step 2 – Install VGA Driver 1. Click on the Step2-VGA folder and double click on the Setup.exe 2.
Industrial Motherboard EMB-CV1 series 2. Follow the instructions that the window shows 3. The system will help you install the driver automatically Step 5 –Install AHCI Driver 1. Click on the Step5-AHCI folder and select the folder of AP 2. Double click on the setup.exe 3. Follow the instructions that the window shows 4.
Industrial Motherboard EMB-CV1 series Appendix A Programming the Watchdog Timer Appendix A Programming the Watchdog Timer A-1
Industrial Motherboard EMB-CV1 series A.1 Programming EMB-CV1 utilizes ITE 8783 chipset as its watchdog timer controller. Below are the procedures to complete its configuration and this initial watchdog timer program is also attached based on which you can develop customized program to fit your application. Configuring Sequence Description After the hardware reset or power-on reset, the ITE 8783 enters the normal mode with all logical devices disabled except KBC.
Industrial Motherboard EMB-CV1 series There are three steps to complete the configuration setup: (1) Enter the MB PnP Mode; (2) Modify the data of configuration registers; (3) Exit the MB PnP Mode. Undesired result may occur if the MB PnP Mode is not exited normally. (1) Enter the MB PnP Mode To enter the MB PnP Mode, four special I/O write operations are to be performed during Wait for Key state.
Industrial Motherboard EMB-CV1 series WatchDog Timer Configuration Registers Configure Control (Index=02h) This register is write only. Its values are not sticky; that is to say, a hardware reset will automatically clear the bits, and does not require the software to clear them.
Industrial Motherboard EMB-CV1 series Watch Dog Timer 1, 2, 3 Configuration Register (Index=72h, 82h, 92h Default=001s0000b) Watch Dog Timer 1,2,3 Time-Out Value (LSB) Register (Index=73h,83h,93h, Default=38h) Watch Dog Timer 1,2,3 Time-Out Value (MSB) Register (Index=74h,84h,94h Default=00h) Appendix A Programming the Watchdog Timer A-5
Industrial Motherboard EMB-CV1 series A.2 ITE8783 Watchdog Timer Initial Program .MODEL SMALL .CODE Main: CALL Enter_Configuration_mode CALL Check_Chip mov cl, 7 call Set_Logic_Device ;time setting mov cl, 10 ; 10 Sec dec al Watch_Dog_Setting: ;Timer setting mov al, cl mov cl, 73h call Superio_Set_Reg ;Clear by keyboard or mouse interrupt mov al, 0f0h mov cl, 71h call Superio_Set_Reg ;unit is second.
Industrial Motherboard EMB-CV1 series call Superio_Set_Reg ; game port enable mov cl, 9 call Set_Logic_Device Initial_OK: CALL Exit_Configuration_mode MOV AH,4Ch INT 21h Enter_Configuration_Mode PROC NEAR MOV SI,WORD PTR CS:[Offset Cfg_Port] MOV DX,02Eh MOV CX,04h Init_1: MOV AL,BYTE PTR CS:[SI] OUT DX,AL INC SI LOOP Init_1 RET Enter_Configuration_Mode ENDP Exit_Configuration_Mode PROC NEAR MOV AX,0202h Appendix A Programming the Watchdog Timer A-7
Industrial Motherboard EMB-CV1 series CALL Write_Configuration_Data RET Exit_Configuration_Mode ENDP Check_Chip PROC NEAR MOV AL,20h CALL Read_Configuration_Data CMP AL,87h JNE Not_Initial MOV AL,21h CALL Read_Configuration_Data CMP AL,81h JNE Not_Initial Need_Initial: STC RET Not_Initial: CLC RET Check_Chip ENDP Read_Configuration_Data PROC NEAR MOV DX,WORD PTR CS:[Cfg_Port+04h] Appendix A Programming the Watchdog Timer A-8
Industrial Motherboard EMB-CV1 series OUT DX,AL MOV DX,WORD PTR CS:[Cfg_Port+06h] IN AL,DX RET Read_Configuration_Data ENDP Write_Configuration_Data PROC NEAR MOV DX,WORD PTR CS:[Cfg_Port+04h] OUT DX,AL XCHG AL,AH MOV DX,WORD PTR CS:[Cfg_Port+06h] OUT DX,AL RET Write_Configuration_Data ENDP Superio_Set_Reg proc near push ax MOV DX,WORD PTR CS:[Cfg_Port+04h] mov al,cl out dx,al pop ax inc dx out dx,al ret Superio_Set_Reg endp.
Industrial Motherboard Set_Logic_Device proc EMB-CV1 series near push ax push cx xchg al,cl mov cl,07h call Superio_Set_Reg pop cx pop ax ret Set_Logic_Device endp ;Select 02Eh->Index Port, 02Fh->Data Port Cfg_Port DB 087h,001h,055h,055h DW 02Eh,02Fh END Main Note: Interrupt level mapping 0Fh-Dh: not valid 0Ch: IRQ12 . .
Industrial Motherboard EMB-CV1 series Appendix B Mating Connector Appendix B Mating Connector B - 1
Industrial Motherboard EMB-CV1 series B.1 List of Mating Connectors and Cables The table notes mating connectors and available cables. Connector Label Mating Connector Function Vendor PINREX Model No. POWER CON 4P S/T,ATX,W/PG2 PINREX/740-41-0 4TWC0.DIP WAFER HD 4P S/T 2.54MM L-GRAY PINREX/744-81-0 4TG20 [EL].DIP (TF)BOX HEADER.5*2P.18 0D.(M).2.0mm.DI P.WO PIN10.CATCH.11 47-000-10SA (TF)BOX HEADER.5*2P.18 0D.(M).2.0mm.DI P.WO PIN10.CATCH.11 47-000-10SA (TF)BOX HEADER.5*2P.18 0D.(M).2.0mm.DI P.WO PIN10.
Industrial Motherboard CPU_FAN CPU FAN connector PINREX GPIO/SM BUS/COM2 DIGITALREF / COM2 JVE ENCE external power select F_PANEL Front panel PINREX pin header KB/MS PS/2 Keyboard / Ho-Base Mouse connector LVDS panel LCD_POWE power CATCH connector LPT Parallel port PINREX connector EMB-CV1 series WAFER HD 4P S/T 2.54MM L-GRAY PINREX/744-81-0 4TG20 [EL].DIP HEADER 2X10P,S/T,2.0mm ,STACK JVE/21N22050-2 0S22B01G4/9.2/2 .DIP HEADER 2X5P 2.54mm S/T.K10 G/F PINREX/210-92-0 5GB02 (TF)WAFER BOX.6P.
Industrial Motherboard Serial ATA SATA_PWR1 power Connector CATCH SATA3G_1 SATA 0 Connector LOTES SATA3G_2 SATA 1 Connector LOTES USB56 USB 5 & 6 JVE pin header WLAN Mini PCI-E LOTES SLOT EMB-CV1 series BLUE E-MOVE/EE0360 -1GGZ-00H [GA].DIP (TF)WAFER.4P.1 80D.(M).2.5mm. W/LOCK POWER DIP.CATCH.1198700-04S. SATA CON 7P S/T G/F,DIP,CHARL LOTES/ABA-SAT046-K13.DIP SATA CON 7P S/T G/F,DIP,CHARL LOTES/ABA-SAT046-K13.DIP (TF)PIN HEADER.5*2P.18 0D.(M).2.0mm.DI P MINI PCI-E 52P,0.8MM,9.
