Mini-ITX EMB-CV2 EMB-CV2 Intel® AtomTM D2550 B3 Processor Mini-ITX 10/100/1000Base-TX Ethernet 8 USB2.0, 2 COM, 8-bit Digital I/O 6 SATA 3.0 Gb/s, 1 PCI-E[x4] st EMB-CV2 Manual Rev.A 1 Ed.
Mini-ITX EMB-CV2 Copyright Notice This document is copyrighted, 2014. All rights are reserved. The original manufacturer reserves the right to make improvements to the products described in this manual at any time without notice. No part of this manual may be reproduced, copied, translated, or transmitted in any form or by any means without the prior written permission of the original manufacturer. Information provided in this manual is intended to be accurate and reliable.
Mini-ITX EMB-CV2 Acknowledgments All other products’ name or trademarks are properties of their respective owners. AMI is a trademark of American Megatrends Inc. CompactFlash™ is a trademark of the Compact Flash Association. Intel® and Atom™ are trademarks of Intel® Corporation. Microsoft Windows® is a registered trademark of Microsoft Corporation. ITE is a trademark of Integrated Technology Express, Inc.
EMB-CV2 Mini-ITX Packing List (Standard, not bulk pack) Before you begin installing your card, please make sure that the following materials have been shipped: 1 Cable Set (SATA Cable, SATA Power Cable) 1 Metal I/O Bracket 1 Product CD 1 EMB-CV2 If any of these items should be missing or damaged, please contact your distributor or sales representative immediately.
EMB-CV2 Mini-ITX Contents Chapter 1 General Information 1.1 Features .................................................................... 1-2 1.2 Specifications ............................................................ 1-3 Chapter 2 Quick Installation Guide 2.1 Safety Precautions .................................................... 2-2 2.2 Location of Connectors and Jumpers ....................... 2-3 2.3 Mechanical Drawing .................................................. 2-4 2.4 List of Jumpers ...
Mini-ITX EMB-CV2 2.17 Digital I/O (CN2) .................................................... 2-12 2.18 PS/2 Keyboard Mouse Pin Header (KBMS1) ....... 2-12 2.19 CPU Fan & System Fan Connector (CPU_FAN1) (SYS_FAN1) .................................................................. 2-13 2.20 ATX AUX in +12V Connector (ATX1) ................... 2-13 2.21 ATX Power Board Control Pin Header (CN11) ..... 2-13 2.22 COM Port Connector (COM2) ............................... 2-13 Chapter 3 AMI BIOS Setup 3.
Mini-ITX Appendix D EMB-CV2 AHCI & RAID Settings D.1 Setting AHCI ............................................................ .D-2 D.2 Setting RAID ............................................................ .
Mini-ITX EMB-CV2 Chapter 1 General Information Chapter 1 General Information 1- 1
Mini-ITX EMB-CV2 1.1 Features ® Onboard Intel Atom™ D2550 Processor Intel ICH10R Intel Graphics Media Accelerator Supports DirectX 10, ® ® OpenGL 3.0 DDR3 800/1066 SO-DIMM x 2, Max. 4GB VGA, Dual Channel 24-bit LVDS, DVI, Dual Independent Display Dual Gigabit Ethernet COM x 2 (RS232 x 1, RS232/422/485 x 1) USB2.
EMB-CV2 Mini-ITX 1.2 Specifications System Processor Intel® Atom™ D2550 processor Dual Core 1.86GHz (TDP 10W) System Memory Single Channel with two 204-pin DDR3 800 /1066 SODIMM, up to 4 GB, non-ECC, un-buffered memory with 0.
EMB-CV2 Mini-ITX Storage Temperature -40˚F ~176°F (-40°C ~80°C) Operating Humidity 5%～95%RH, non-condensing Display Chipset Intel® Graphics Media Accelerator 3650 (Gfx frequency 640MHz / DX10.1) Resolution Up to 1920 x 1200 / 60Hz at 355MHz Max for CRT Up to 1920 x 1080 / 60Hz, 24bpps for Dual Channel LVDS (from eDP w/chrontel CH7511) Up to 1920 x1200 / 60Mz for DVI LVDS Interface Dual Channel 24-bit LVDS Video Interface VGA x 1, DVI-D x 1 Storage SATA 3.
Mini-ITX EMB-CV2 2.
Mini-ITX EMB-CV2 Chapter 2 Quick Installation Guide Chapter 2 Quick Installation Guide 2 - 1
Mini-ITX 2.1 EMB-CV2 Safety Precautions Always completely disconnect the power cord from your board whenever you are working on it. Do not make connections while the power is on, because a sudden rush of power can damage sensitive electronic components. Always ground yourself to remove any static charge before touching the board. Modern electronic devices are very sensitive to static electric charges. Use a grounding wrist strap at all times.
Mini-ITX 2.
Mini-ITX 2.
Mini-ITX EMB-CV2 Solder Side Chapter 2 Quick Installation Guide 2 - 5
EMB-CV2 Mini-ITX 2.4 List of Jumpers The board has a number of jumpers that allow you to configure your system to suit your application.
EMB-CV2 Mini-ITX 2.5 List of Connectors The board has a number of connectors that allow you to configure your system to suit your application.
EMB-CV2 Mini-ITX CPU_FAN1 CPU fan connector SYS_FAN1 System fan connector FP1 Front panel pin header AUDIO1 Audio phone jack LAN1_USB01 RJ-45 Ethernet 1 & USB 0/1 connector LAN2_USB23 RJ-45 Ethernet 2 & USB 2/3 connector ATX1 ATX AUX in +12v Connector DC1 DC 12V in CN11 ATX power board control pin header NOTE: The +12V Power connector (Label: DC_PWR) is lockable Jack type with screw. Please refer the inner and outer diameter dimension of connector as below to choose suitable adaptor.
EMB-CV2 Mini-ITX 2.6 Setting Jumpers You configure your card to match the needs of your application by setting jumpers. A jumper is the simplest kind of electric switch. It consists of two metal pins and a small metal clip (often protected by a plastic cover) that slides over the pins to connect them. To “close” a jumper you connect the pins with the clip. To “open” a jumper you remove the clip. Sometimes a jumper will have three pins, labeled 1, 2 and 3.
EMB-CV2 Mini-ITX 2.7 2.8 2.9 AT/ATX Power Type Selection (AT_ATX_SEL1) ATOMODE Function Close 1-2 AT Close 2-3 ATX Mode (Default) Clear CMOS/ RTC (CLRTC1) CLRTC Function Close 1-2 Protected (Default) Close 2-3 Clear LVDS Backlight Brightness Control (LVDSBRC1) LVDSBRC Function Close 1-2 Voltage control (Default) Close 2-3 CH7511 PWM control 2.10 LVDS Panel Voltage Selection (LVDS_PVSEL1) LVDS_PVSEL Function Close 1-3 +5V Close 3-5 +3.3V (Default) 2.
EMB-CV2 Mini-ITX 2.12 Serial Port 2 External Power Selection (CN10) POWER_SEL Function Close 5-6 +12V Close 7-8 RI# (Default) Close 9-10 +5V (Default) 2.13 Front Panel Connector (FP1) Pin Signal Pin Signal 1 PWRBTN- 2 PWRBTN+ 3 IDELED- 4 IDELED+ 5 BUZZER- 6 BUZZER+ 7 POWERLED- 8 POWERLED+ 9 RESET- 10 RESET+ 2.
EMB-CV2 Mini-ITX 25 LVDS2_DATA3# 26 LVDS2_DATA3 27 LVDSVCC 28 GND 29 LVDS2_CLK# 30 LVDS2_CLK 2.15 SATA Power Connector (SATA_PWR1) Pin Signal Pin Signal 1 +5V 2 GND 3 GND 4 +12V 2.16 USB 4 /5 / 6 / 7 Pin Header (USB45_1) (USB67_1) Pin Signal Pin Signal 1 +5V 2 GND 3 USBD- 4 GND 5 USBD+ 6 USBD+ 7 GND 8 USBD- 9 GND 10 +5V 2.17 Digital I/O (CN2) This connector offers 4-pair of digital I/O functions and address is 0xA00H.
EMB-CV2 Mini-ITX 3 GND 4 +5V 5 Mouse DATA 6 Mouse CLOCK 7 NC 8 NC 2.19 CPU Fan & System Fan Connector (CPU_FAN1) (SYS_FAN1) Pin Signal Pin Signal 1 GND 2 +12V 3 FAN sense 4 FAN Control 2.20 ATX AUX in +12V Connector (ATX1) Pin Signal Pin Signal 1 GND 2 GND 3 +12V 4 +12V 2.21 ATX Power Board Control Pin Header (CN11) Pin Signal Pin Signal 1 PWRBTN# 2 PWROK 3 PSON# 2.
EMB-CV2 Mini-ITX RS-232 Pin Signal Signal Type 1 DCD1 Input 2 RXD1 Input 3 TXD1 Output ±9V 4 DTR1 Output ±9V 5 GND GND 6 DSR1 Input 7 RTS1 Output 8 CTS1 RI1 / +12V 9 Signal Level ±9V Input +5V / Input / PWR By Jumper Selection Note: The max.
EMB-CV2 Mini-ITX 3 RS485_D+ 4 NC 5 GND 6 NC 7 NC 8 NC 9 NC / +5V / +12V DIFF GND By Jump Selection PWR Note: The max.
Mini-ITX EMB-CV2 Chapter 3 AMI BIOS Setup Chapter 3 AMI BIOS Setup 3-1
Mini-ITX 3.1 EMB-CV2 System Test and Initialization These routines test and initialize board hardware. If the routines encounter an error during the tests, you will either hear a few short beeps or see an error message on the screen. There are two kinds of errors: fatal and non-fatal. The system can usually continue the boot up sequence with non-fatal errors. System configuration verification These routines check the current system configuration against the values stored in the CMOS memory.
EMB-CV2 Mini-ITX 3.2 AMI BIOS Setup AMI BIOS ROM has a built-in Setup program that allows users to modify the basic system configuration. This type of information is stored in battery-backed CMOS RAM so that it retains the Setup information when the power is turned off. Entering Setup Power on the computer and press or immediately. This will allow you to enter Setup. Main Set the date, use tab to switch between date elements. Advanced Advanced BIOS Features Setup including TPM, ACPI, etc.
Mini-ITX Setup Menu Setup submenu: Main Chapter 3 AMI BIOS Setup 3-4 EMB-CV2
Mini-ITX EMB-CV2 Setup submenu: Advanced Chapter 3 AMI BIOS Setup 3-5
Mini-ITX EMB-CV2 ACPI Settings Options summary: Suspend mode Suspend Disable S3 only (Suspend to RAM) Select the ACPI state used for System Suspend Chapter 3 AMI BIOS Setup 3-6 Default
Mini-ITX EMB-CV2 CPU Configuration Options summary : Hyper-threading Disable Enabled Default Enabled for Windows XP and Linux (OS optimized for Hyper-Threading Technology) and Disabled for other OS (OS not optimized for Hyper-Threading Technology). When Disabled only on thread per enabled core is enabled.
Mini-ITX EMB-CV2 SATA Configuration Options summary : Hyper-threading Disable IDE Mode AHCI Mode RAID Mode Determines how SATA controller(s) operate.
Mini-ITX EMB-CV2 USB Configuration Options summary: Legacy USB Support Enabled Default Disabled Auto Enables Legacy USB support. AUTO option disables legacy support if no USB devices are connected. DISABLE option will keep USB device available only for EFI applications.
Mini-ITX W83627DHG Super IO Configuration Chapter 3 AMI BIOS Setup 3-10 EMB-CV2
Mini-ITX EMB-CV2 Serial Port 1 Configuration Options summary: Serial Port Disabled Enabled Default Allows BIOS to En/Disable correspond serial port. Change Settings Auto Default IO=3F8h; IRQ=4; IO=3F8h; IRQ=3,4,5,6,7,10,11,12; IO=2F8h; IRQ=3,4,5,6,7,10,11,12; IO=3E8h; IRQ=3.4,5,6,7,10,11,12; IO=2E8h; IRQ=3,4,5,6,7,10,11,12; Allows BIOS to Select Serial Port resource.
Mini-ITX EMB-CV2 Serial Port 2 Configuration Options summary: Serial Port Disabled Enabled Default Allows BIOS to En/Disable correspond serial port. Change Settings Auto Default IO=2F8h; IRQ=3; IO=3F8h; IRQ=3,4,5,6,7,10,11,12; IO=2F8h; IRQ=3,4,5,6,7,10,11,12; IO=3E8h; IRQ=3.4,5,6,7,10,11,12; IO=2E8h; IRQ=3,4,5,6,7,10,11,12; Allows BIOS to Select Serial Port resource. Device Mode RS232 Default RS422 RS485 Select working model.
Mini-ITX EMB-CV2 W83627DHG H/W Monitor Options summary: Smart Fan Function Disabled Enabled Enable or Disable Smart Fan.
Mini-ITX EMB-CV2 Smart Fan Mode Configuration Options summary: CPU Smart Fan Mode Manual Mode Thermal Cruise Mode CPU Smart Fan Mode Select CPUFAN PWM/DC Voltage 0~255 Output Input expect PWM Output Value(Range: 0 – 255) SYS Smart Fan Mode Manual Mode Thermal Cruise Mode SYS Smart Fan Mode Select SYSFAN PWM/DC Voltage 0~255 Output Input expect PWM Output Value(Range: 0 – 255) Chapter 3 AMI BIOS Setup 3-14 Default Default : 255 Default Default : 255
Mini-ITX EMB-CV2 Dynamic Digital IO Options summary: DIO0 Direction Input Output Set Digital IO as Input or Output DIO1 Direction Input Output Set Digital IO as Input or Output DIO2 Direction Input Output Set Digital IO as Input or Output DIO3 Direction Input Output Set Digital IO as Input or Output DIO4 Direction Input Output Set Digital IO as Input or Output Default Default Default Default Default Chapter 3 AMI BIOS Setup 3-15
Mini-ITX Input Output Set Digital IO as Input or Output DIO6 Direction Input Output Set Digital IO as Input or Output DIO7 Direction Input Output Set Digital IO as Input or Output Output Level HI LOW Set Digital IO Output as Hi or Low EMB-CV2 DIO5 Direction Chapter 3 AMI BIOS Setup 3-16 Default Default Default Default
Mini-ITX EMB-CV2 S5 RTC Wake Settings Options summary: Wake system with Fixed Time Disabled Default Enabled Enable or disable System wake on alarm event. When enabled, System will wake on the hr::min::sec specified Wake system with Dynamic Time Disabled Default Enabled Enable or disable System wake on alarm event.
Mini-ITX Setup submenu: Chipset Chapter 3 AMI BIOS Setup 3-18 EMB-CV2
Mini-ITX EMB-CV2 Setup submenu: Host Bridge Chapter 3 AMI BIOS Setup 3-19
Mini-ITX EMB-CV2 Intel IGD Configuration Options summary: IGFX – Boot Type VBIOS Default Default CRT DVI LVDS Select the video device which will be activated during POST. This has no effect if external graphics present. Fixed Graphics Memory size 128MB 256MB Default Configure fixed graphics memory size. LVDS Enable Disabled Default Enabled Select LVDS Disable or Enable.
Mini-ITX EMB-CV2 Setup submenu: South Bridge Options summary: Power Mode ATX Type Default AT Type Select power supply mode. Restore AC Power Loss Power Off Default Power On Last State Specify what state to go to when power is re-applied after a power failure (G3 State). Azalia HD Audio Disabled Enabled Default Control Detection of the Azalia device.
Mini-ITX Resume on Ring EMB-CV2 Disabled Enabled Default For En/Disable Ring In wake up function. Attention please, when this function is enabled, some devices which connect to Serial Port may cause the system auto wake up from sleep mode. PCI Express port 5 Disabled Enabled Default For En/Disable Onboard RTL8111E 1 function. PCI Express port 6 Disabled Enabled Default For En/Disable Onboard RTL8111E 2 function.
Mini-ITX EMB-CV2 Setup submenu: Boot Options summary: Quiet Boot Disabled Enabled Enables or disables Quiet Boot option Launch PXE OpROM Disabled Enabled En/Disable PXE boot for RTL8111E LAN Default Default Chapter 3 AMI BIOS Setup 3-23
Mini-ITX EMB-CV2 Security Change User/Supervisor Password You can install a Supervisor password, and if you install a supervisor password, you can then install a user password. A user password does not provide access to many of the features in the Setup utility. If you highlight these items and press Enter, a dialog box appears which lets you enter a password. You can enter no more than six letters or numbers. Press Enter after you have typed in the password.
Mini-ITX EMB-CV2 Setup submenu: Exit Chapter 3 AMI BIOS Setup 3-25
Mini-ITX EMB-CV2 Chapter 4 Driver Installation 0B .
Mini-ITX EMB-CV2 The EMB-CV2 comes with an Autorun CD-ROM that contains all drivers and utilities that can help you to install the driver automatically. Insert the driver CD, the driver CD-title will automatically start and show the installation guide. If not, please follow the sequence below to install the drivers.
Mini-ITX 4.1 EMB-CV2 Installation: Insert the EMB-CV2 CD-ROM into the CD-ROM drive. And install the drivers from Step 1 to Step 6 in order. Step 1 – Install Chipset Driver 1. Click on the Step 1 - INF folder and double click on the infinst_autol.exe 2. Follow the instructions that the window shows 3. The system will help you install the driver automatically Step 2 – Install VGA Driver ® For Windows 7 1. Click on the Step 2 - VGA folder and select the folder of Win7 2. Double click on the Setup.
Mini-ITX EMB-CV2 Select the configuration Follow the instructions that the window shows The system will help you install the driver automatically Chapter 4 Driver Installation 4 -4
Mini-ITX EMB-CV2 If you want to update driver, please uninstall driver first. Uninstall IEMGD 1. Double click on the IEMGDInstall.exe 2. Follow the instructions that the window shows 3.
Mini-ITX EMB-CV2 Step 3 –Install LAN Driver 1. Click on the Step 3 - LAN folder and double click on the setup.exe 2. Follow the instructions that the window shows 3. The system will help you install the driver automatically Step 4 –Install Audio Driver 1. Click on the Step 4 - AUDIO folder and double click on the SETUP.exe 2. Follow the instructions that the window shows 3.
Mini-ITX EMB-CV2 3. The system will help you install the driver automatically ® For Windows 7 32-bit/ 64-bit Create a password for Administrator account.
Mini-ITX EMB-CV2 Reboot and Administrator login. To run patch.bat with [Run as administrator].
Mini-ITX EMB-CV2 Chapter 4 Driver Installation 4 -9
Mini-ITX EMB-CV2 Appendix A Programming the Watchdog Timer Appendix A Programming the Watchdog Timer A-1
Mini-ITX EMB-CV2 A.1 Programming EMB-CV2 utilizes W83627DHG chipset as its watchdog timer controller. Below are the procedures to complete its configuration and the AAEON intial watchdog timer program is also attached based on which you can develop customized program to fit your application.
Mini-ITX EMB-CV2 (3) Exit the W83627DHG config Mode. Undesired result may occur if the config Mode is not exited normally. (1) Enter the W83627DHG config Mode To enter the W83627DHG config Mode, two special I/O write operations are to be performed during Wait for Key state. To ensure the initial state of the key-check logic, it is necessary to perform two write operations to the Special Address port (2EH). The different enter keys are provided to select configuration ports (2Eh/2Fh) of the next step.
Mini-ITX EMB-CV2 1 R/W 0: GPIO5 is inactive. 1: GPIO5 is active. 0 R/W 0: WDTO# and PLED are inactive. 1: WDTO# and PLED are inactive. CR F5h. (WDTO# and KBC P20 Control Mode Register; Default 00h) BIT READ/WRITE 7~5 Reserved. 4 R/W 3 R/W 2 R/W 1 R/W 0 DESCRIPTION 1000 time faster in WDTO# count mode. 0: Disable. 1: Enable. (If bit-3 is Second Mode, the count mode is 1/1000 Sec.) (If bit-3 is Minute Mode, the count mode is 1/1000 Min.) Select WDTO# count mode. 0: Second Mode.
Mini-ITX EMB-CV2 01h: Time-out occurs after 1 second/minute 02h: Time-out occurs after 2 second/minutes 03h: Time-out occurs after 3 second/minutes ………………………………………………….. FFh: Time-out occurs after 255 second/minutes CR F7h. (WDTO# Control & Status Register; Default 00h) BIT READ/WRITE 7 R/W 6 R/W 5 Write “1” Only 4 R/W Write“0”Clear 3~0 R/W DESCRIPTION Mouse interrupt reset watch-dog timer enable 0: Watchdog timer is not affected by mouse interrupt.
Mini-ITX EMB-CV2 A.2 W83627DHG Watchdog Timer Initial Program LDN Register Bit WDT Timer value 0x07 0xF6 Bit [7-0] WDT Unit 0x07 0xF5 Bit3 Description 00h: Time-out Disable 01h: Time-out occurs after 1 minute only. 02h: Time-out occurs after 2 second/minutes 03h: Time-out occurs after 3 second/minutes ………………………....................................... FFh: Time-out occurs after 255 second/minutes (The deviation is approx 1 second.) Select WDTO# count mode. 0: Second Mode. 1: Minute Mode.
Mini-ITX EMB-CV2 ************************************************************************************ // Procedure : AaeonWDTConfig void AaeonWDTConfig (void){ Byte val; //Super I/O Entry Key outportb(SIOIndex,0x87); outportb(SIOIndex,0x87); //Setting WDT Pin.
Mini-ITX EMB-CV2 ************************************************************************************ // Procedure : void AaeonWDTEnable (Byte Timer, boolean Unit){ Byte val; //Super I/O Entry Key outportb(SIOIndex,0x87); outportb(SIOIndex,0x87); // Select Logic Device Number Register outportb(SIOIndex,0x07); outportb(SIOData,0x08); // Setting WDT Operation Mode outportb(SIOIndex,0xF5); val = inportb((SIOData); outportb(SIOIndex,0xF5); outportb(SIOData, val | Unit << 3 ); // Setting WDT Counter outportb(S
Mini-ITX EMB-CV2 Appendix B I/O Information Appendix B I/O Information B-1
Mini-ITX B.
Mini-ITX EMB-CV2 Appendix B I/O Information B-3
Mini-ITX st B.
Mini-ITX EMB-CV2 B.
Mini-ITX Appendix B I/O Information B-6 EMB-CV2
Mini-ITX EMB-CV2 B.
Mini-ITX EMB-CV2 Appendix C Mating Connector Appendix C Mating Connector C - 1
EMB-CV2 Mini-ITX C.1 List of Mating Connectors and Cables The table notes mating connectors and available cables. Connector Label Mating Connector Function Vendor PINREX Model No. POWER CON 4P S/T,ATX,W/PG2 PINREX/740-41-0 4TWC0.DIP WAFER HD 4P S/T 2.54MM L-GRAY PINREX/744-81-0 4TG20 [EL].DIP (TF)BOX HEADER.5*2P.18 0D.(M).2.0mm.DI P.WO PIN10.CATCH.11 47-000-10SA (TF)BOX HEADER.5*2P.18 0D.(M).2.0mm.DI P.WO PIN10.CATCH.11 47-000-10SA (TF)BOX HEADER.5*2P.18 0D.(M).2.0mm.DI P.WO PIN10.CATCH.
Mini-ITX CPU_FAN CPU FAN connector PINREX GPIO/SM BUS/COM2 DIGITALREF / COM2 JVE ENCE external power select F_PANEL Front panel PINREX pin header KB/MS PS/2 Keyboard / Ho-Base Mouse connector LVDS panel LCD_POWE power CATCH connector LPT Parallel port PINREX connector EMB-CV2 WAFER HD 4P S/T 2.54MM L-GRAY PINREX/744-81-0 4TG20 [EL].DIP HEADER 2X10P,S/T,2.0mm ,STACK JVE/21N22050-2 0S22B01G4/9.2/2 .DIP HEADER 2X5P 2.54mm S/T.K10 G/F PINREX/210-92-0 5GB02 (TF)WAFER BOX.6P.180D(M). 2.0mm.
Mini-ITX Serial ATA SATA_PWR1 power Connector CATCH SATA3G_1 SATA 0 Connector LOTES SATA3G_2 SATA 1 Connector LOTES USB56 USB 5 & 6 JVE pin header WLAN Mini PCI-E LOTES SLOT EMB-CV2 BLUE E-MOVE/EE0360 -1GGZ-00H [GA].DIP (TF)WAFER.4P.1 80D.(M).2.5mm. W/LOCK POWER DIP.CATCH.1198700-04S. SATA CON 7P S/T G/F,DIP,CHARL LOTES/ABA-SAT046-K13.DIP SATA CON 7P S/T G/F,DIP,CHARL LOTES/ABA-SAT046-K13.DIP (TF)PIN HEADER.5*2P.18 0D.(M).2.0mm.DI P MINI PCI-E 52P,0.8MM,9.0H SMT LOTES/AAA-PCI047-P01 [HF].
Mini-ITX EMB-CV2 Appendix D AHCI & RAID Settings Appendix D AHCI & RAID Settings D-1
Mini-ITX EMB-CV2 D.1 Setting AHCI OS Installation to Setup AHCI mode Step 1: Copy the files below from the Driver CD: Step 5 AHCI\Floppy\f6flpy-x86 or f6flpy-x64 to Disk. Step 2: Connect the USB Floppy Disk with the AHCI files to the board.
Mini-ITX EMB-CV2 Step 3: To install “In BIOS Setup Menu”, select Advanced -> SATA Configuration -> SATA Mode -> AHCI Mode Appendix D AHCI & RAID Settings D-3
Mini-ITX EMB-CV2 Step 4: To save, select Save & Exit -> Save Changes and Exit Step 5: Setup OS Appendix D AHCI & RAID Settings D-4
Mini-ITX EMB-CV2 Step 6: Press “F6” Step 7: Choose “S” Appendix D AHCI & RAID Settings D-5
Mini-ITX EMB-CV2 Step 8: Choose “Intel(R) ICH10R SATA AHCI Controller” Appendix D AHCI & RAID Settings D-6
Mini-ITX EMB-CV2 Step 9: Select “ENTER” to choose the model number Appendix D AHCI & RAID Settings D-7
Mini-ITX Step 10: Setup is loading files Appendix D AHCI & RAID Settings D-8 EMB-CV2
Mini-ITX EMB-CV2 D.2 Setting RAID OS Installation to Setup RAID mode Step 1: Copy the files below from the Driver CD: Step 5 AHCI\Floppy\f6flpy-x86 or f6flpy-x64 to Disk. Step 2: Connect the USB Floppy Disk with the RAID files to the board.
Mini-ITX EMB-CV2 Step 3: To install “In BIOS Setup Menu”, select Advanced -> SATA Configuration -> SATA Mode -> RAID Mode Appendix D AHCI & RAID Settings D-10
Mini-ITX EMB-CV2 Step 4: To save, select Save & Exit -> Save Changes and Exit Appendix D AHCI & RAID Settings D-11
Mini-ITX Step 5: Press Ctrl-I to enter MAIN MENU.
Mini-ITX EMB-CV2 Step 6: Choose “1.
Mini-ITX Step 8: Choose “Y” Step 9: Choose “6.
Mini-ITX EMB-CV2 Step 10: Setup OS Step 11: Press “F6” Appendix D AHCI & RAID Settings D-15
Mini-ITX Step 12: Choose “S” Appendix D AHCI & RAID Settings D-16 EMB-CV2
Mini-ITX EMB-CV2 Step 13: Choose “Intel(R) Desktop/Workstation/Server Express Chipset SATA RAID Controller” Appendix D AHCI & RAID Settings D-17
Mini-ITX EMB-CV2 Step 14: Select “ENTER” to choose the model number Appendix D AHCI & RAID Settings D-18
Mini-ITX EMB-CV2 Step 15: Setup is loading files Appendix D AHCI & RAID Settings D-19
