EPIC Board EPIC-CV07 EPIC-CV07 ® TM Intel Atom N2600/ D2550 Processor Onboard DDR3 800/1066 MHz SODIMM 18/24-bit Single/ Dual-channel LVDS LCD 8 USB2.0, 8 COM 1 SATA, 1mSATA 2 Gigabit Ethernet, PCI-104, Mini Card EPIC-CV07 Manual Rev. A 1st Ed.
EPIC Board EPIC-CV07 Copyright Notice This document is copyrighted, 2012. All rights are reserved. The original manufacturer reserves the right to make improvements to the products described in this manual at any time without notice. No part of this manual may be reproduced, copied, translated, or transmitted in any form or by any means without the prior written permission of the original manufacturer. Information provided in this manual is intended to be accurate and reliable.
EPIC Board EPIC-CV07 Acknowledgments All other products’ name or trademarks are properties of their respective owners. AMI is a trademark of American Megatrends Inc. CFast™ is a trademark of the Compact Flash Association. Intel®, Atom™ are trademarks of Intel® Corporation. Microsoft Windows® is a registered trademark of Microsoft Corp. ITE is a trademark of Integrated Technology Express, Inc. IBM, PC/AT, PS/2, and VGA are trademarks of International Business Machines Corporation.
EPIC Board EPIC-CV07 Packing List Before you begin installing your card, please make sure that the following materials have been shipped: 1709070500 SATA Cable 1702150155 SATA Power Cable 9657666600 Jumper Cap Heat Spreader DVD-ROM for manual (in PDF format) and drivers EPIC-CV07 If any of these items should be missing or damaged, please contact your distributor or sales representative immediately.
EPIC Board EPIC-CV07 Contents Chapter 1 General Information 1.1 Introduction................................................................ 1-2 1.2 Features .................................................................... 1-3 1.3 Specifications ............................................................ 1-4 Chapter 2 Quick Installation Guide 2.1 Safety Precautions .................................................... 2-2 2.2 Location of Connectors and Jumpers ....................... 2-3 2.
EPIC Board EPIC-CV07 2.15 1st LVDS Port1 Backlight Inverter VCC Selection (JP9) ......................................................................................... 2-13 2.16 1st LVDS-LCD Port1 Operating VDD Selection (JP10) ......................................................................................... 2-14 2.17 2nd LVDS-LCD Backlight Control Selection (JP11) 2-14 2.18 COM2 +5V/Ring/+12V Selection (JP12) ................. 2-14 2.19 +12VSB Power Input Connector (CN1) ..................
EPIC Board EPIC-CV07 2.38 PS2 Keyboard / Mouse Connector (CN20)............. 2-31 2.39 DVI–I/CRT Connector (CN21)................................. 2-32 2.40 8th COM Port Connector (CN22) ............................ 2-34 2.41 7th COM Port Connector (CN23) ............................ 2-35 2.42 6th COM Port Connector (CN24) ............................ 2-36 2.43 5th COM Port Connector (CN25) ............................ 2-36 2.44 4th COM Port Connector (CN26) ............................ 2-37 2.
EPIC Board EPIC-CV07 Chapter 4 Driver Installation 4.1 Installation ................................................................. 4-3 Appendix A Programming The Watchdog Timer A.1 Watchdog Timer Initial Program ............................A-2 Appendix B I/O Information B.1 I/O Address Map ....................................................B-2 B.2 1st MB Memory Address Map ................................B-4 B.3 IRQ Mapping Chart ................................................B-5 B.
EPIC Board EPIC-CV07 Chapter 1 General Information Chapter 1 General Information 1- 1
EPIC Board EPIC-CV07 1.1 Introduction AAEON, a leading embedded boards manufacturer, is pleased to announce the debut of their new EPIC Board—EPIC-CV07. EPIC-CV07 adopts Intel® AtomTM N2600/ D2550 Processor. The system memory is deployed with 204-pin SODIMM DDR3 800/1066 up to 4 GB for Intel® AtomTM D2550 processor and up to 2 GB for Intel® AtomTM N2600 Processor. In addition, Realtek RTL8111E supports two 10/100/1000Base-TX that allows a faster network connections.
EPIC Board EPIC-CV07 1.2 Features Onboard Intel® Atom™ N2600/ D2550 Processor Intel® NM10 DDR3 800/1066 SODIMM , Max. 4 GB for Intel® Atom™ D2550 Processor, and Max. 2 GB for Intel® Atom™ N2600 Processor Gigabit Ethernet x 2 CRT, 18-bit Single Channel LVDS x 1, 24-bit Dual Channel LVDS x 1, VGA x 1, DVI-I x 1 SATA 3.0Gb/s x 1, mSATA x 1 USB2.
EPIC Board EPIC-CV07 1.3 Specifications System Processor Intel® Atom™ N2600/ D2550 processor (1.6 GHz ~ 1.86 GHz) System Memory 204-pin DDR3 SODIMM x 1, Max. 4 GB (DDR3 800/1066) for Intel® Atom™D2550; Max.
EPIC Board EPIC-CV07 Connector x 1 (via USB7) Power Requirement +12V, ATX Battery Lithium battery Board Size 6.5”(L) x 4.53”(W) (165mm x 115mm) Gross Weight Operating Temperature 32˚F~ 140˚F (0˚C ~ 60˚C) Storage Temperature -4˚F~ 158˚F (-20˚C ~ 70˚C) Operating Humidity 0%~80% relative humidity, 0.88 lb (0.
EPIC Board EPIC-CV07 x1 Parallel Port LPT x 1 USB Port USB2.
EPIC Board EPIC-CV07 Chapter 2 Quick Installation Guide Chapter 2 Quick Installation Guide 2-1
EPIC Board EPIC-CV07 2.1 Safety Precautions Always completely disconnect the power cord from your board whenever you are working on it. Do not make connections while the power is on, because a sudden rush of power can damage sensitive electronic components. Always ground yourself to remove any static charge before touching the board. Modern electronic devices are very sensitive to static electric charges. Use a grounding wrist strap at all times.
EPIC Board EPIC-CV07 2.
EPIC Board Solder Side Solder Side Chapter 2 Quick Installation Guide 2-4 EPIC-CV07
EPIC Board EPIC-CV07 2.
EPIC Board Solder Side Solder Side Chapter 2 Quick Installation Guide 2-6 EPIC-CV07
EPIC Board EPIC-CV07 2.4 List of Jumpers The board has a number of jumpers that allow you to configure your system to suit your application.
EPIC Board EPIC-CV07 2.5 List of Connectors The board has a number of connectors that allow you to configure your system to suit your application.
EPIC Board EPIC-CV07 CN20 PS2 Keyboard / Mouse Connector CN21 DVI-I/CRT Connector CN22 8th COM Port Connector CN23 7th COM Port Connector CN24 6th COM Port Connector CN25 5th COM Port Connector CN26 4th COM Port Connector CN27 3th COM Port Connector CN28 Left Speaker Connector CN29 Right Speaker Connector LAN1 10 /100 /1000 Base-Tx Ethernet Connector LAN2 10 /100 /1000 Base-Tx Ethernet Connector MINICARD1 Mini PCI Express Connector MINICARD2 Mini PCI Express/mSATA Connector S
EPIC Board EPIC-CV07 2.6 Setting Jumpers You configure your card to match the needs of your application by setting jumpers. A jumper is the simplest kind of electric switch. It consists of two metal pins and a small metal clip (often protected by a plastic cover) that slides over the pins to connect them. To “close” a jumper you connect the pins with the clip. To “open” a jumper you remove the clip. Sometimes a jumper will have three pins, labeled 1, 2 and 3.
EPIC Board EPIC-CV07 2.7 Clear CMOS (JP1) JP1 1 2 3 1 2 3 Normal (Default) Clear CMOS Function 1-2 Normal (Default) 2-3 Clear CMOS 2.8 PCI104 VIO Voltage Selection (JP2) 1 2 3 1 2 3 +5V +3.3V (Default) JP2 Function 1-2 +5V 2-3 +3.3V (Default) 2.
EPIC Board EPIC-CV07 2.10 AT/ATX Selection (JP4) 1 2 3 1 2 3 ATX Mode (Default) AT Mode JP4 Function 1-2 ATX Mode (Default) 2-3 AT Mode 2.11 2nd LVDS Port 2 Backlight Inverter VCC Selection (JP5) 1 2 3 1 2 3 +12V +5V (Default) JP5 Function 1-2 +12V 2-3 +5V (Default) 2.12 2nd LVDS-LCD Port 2 Operating VDD Selection (JP6) 1 2 3 1 2 3 +5V +3.3V (Default) JP6 Function 1-2 +5V 2-3 +3.
EPIC Board EPIC-CV07 2.13 2nd LVDS Backlight Lightness Control Mode Selection (JP7) 1 2 3 1 2 3 VR Mode (Default) PWM Mode JP7 Function 1-2 VR Mode (Default) 2-3 PWM Mode 2.14 1st LVDS Backlight Lightness Control Mode Selection (JP8) 1 2 3 1 2 3 VR Mode (Default) PWM Mode JP8 Function 1-2 VR Mode (Default) 2-3 PWM Mode 2.
EPIC Board EPIC-CV07 2.16 1st LVDS-LCD Port1 Operating VDD Selection (JP10) 1 2 3 1 2 3 +5V +3.3V (Default) JP10 Function 1-2 +5V 2-3 +3.3V(Default) 2.17 2nd LVDS-LCD Backlight Control Selection (JP11) 1 2 3 1 2 3 BKL_UP BKL_DN JP11 Function 1-2 BKL_UP 2-3 BKL_DN 2.
EPIC Board EPIC-CV07 2.19 +12VSB Power Input Connector (CN1) Pin Pin Name Signal Type Signal Level 1 GND GND 2 GND GND 3 +12V PWR +12V 4 +12V PWR +12V 2.
EPIC Board EPIC-CV07 7 PWR_LED+ OUT 8 PWR_LED- OUT 9 H/W RESET+ IN 10 H/W RESET- IN 2.21 Power Connector (CN3) Pin Pin Name Signal Type Signal Level 1 +12V PWR +12V 2 GND GND 2.
EPIC Board EPIC-CV07 5 Line_R_IN IN 6 GND_AUDIO GND 7 FRONT_L_OUT OUT 8 GND_AUDIO GND 9 FRONT_R_OUT OUT 10 +5V_AUDIO PWR +5V 2.
EPIC Board EPIC-CV07 2.24 USB Connector (CN6) Pin Pin Name Signal Type Signal Level 1 +5V PWR +5V 2 USB4_D- DIFF 3 USB4_D+ DIFF 4 GND GND 5 GND GND 2.
EPIC Board EPIC-CV07 2.
EPIC Board 6 SENSE(S) 7 NC 8 NC 9 NC EPIC-CV07 IN 2.27 USB Connector (CN9) Pin Pin Name Signal Type Signal Level 1 +5V PWR +5V 2 USB6_D- DIFF 3 USB6_D+ DIFF 4 GND GND 5 GND GND 2.
EPIC Board 5 EPIC-CV07 GND GND 2.29 SATA Power Connector (CN11) Pin Pin Name Signal Type Signal Level 1 +5V PWR +5V 2 GND GND 2.30 SATA Power Connector (CN12) Pin Pin Name Signal Type Signal Level 1 +5V PWR +5V 2 GND GND 2.31 LPC Debug Connector (CN13) Pin Pin Name Signal Type Signal Level 1 LAD0 I/O +3.3V 2 LAD1 I/O +3.
EPIC Board EPIC-CV07 3 LAD2 I/O +3.3V 4 LAD3 I/O +3.3V 5 +3.3V PWR +3.3V 6 FRAME# IN 7 LRESET# OUT 8 GND GND 9 LCLK OUT 10 LDRQ0 IN 11 LDRQ1 IN 12 SERIRQ I/O +3.3V +3.3V 2.32 2nd LCD Inverter Connector (CN14) Pin 1 Pin Name BKL_PWR Signal Type Signal Level PWR +5V / +12V 2 BKL_CONTROL OUT 3 GND GND 4 GND GND 5 BKL_ENABLE OUT Note: BKL_PWR can be set to +5V or +12V by JP5 Chapter 2 Quick Installation Guide 2-22 +3.
EPIC Board EPIC-CV07 2.33 2nd LCD Connector (CN15) Pin Pin Name Signal Type Signal Level 1 BKL_ENABLE OUT +3.3V 2 BKL_CONTROL OUT 3 LCD_PWR PWR 4 GND GND 5 LVDS_A_CLK- DIFF 6 LVDS_A_CLK+ DIFF 7 LCD_PWR PWR 8 GND GND 9 LVDS_DA0- DIFF 10 LVDS_DA0+ DIFF 11 LVDS_DA1- DIFF 12 LVDS_DA1+ DIFF 13 LVDS_DA2- DIFF 14 LVDS_DA2+ DIFF 15 LVDS_DA3- DIFF 16 LVDS_DA3+ DIFF 17 DDC_DATA I/O +3.3V/+5V +3.3V/+5V +3.
EPIC Board EPIC-CV07 18 DDC_CLK I/O 19 LVDS_DB0- DIFF 20 LVDS_DB0+ DIFF 21 LVDS_DB1- DIFF 22 LVDS_DB1+ DIFF 23 LVDS_DB2- DIFF 24 LVDS_DB2 + DIFF 25 LVDS_DB3- DIFF 26 LVDS_DB3+ DIFF 27 LCD_PWR PWR 28 GND GND 29 LVDS_B_CLK- DIFF 30 LVDS_B_CLK+ DIFF +3.3V +3.3V/+5V Note: LCD_PWR can be set to +3.3V or +5V by JP6. 2.
EPIC Board EPIC-CV07 4 ERROR# IN 5 PD1 I/O 6 PRINT# I/O 7 PD2 I/O 8 SLIN# I/O 9 PD3 I/O 10 GND GND 11 PD4 I/O 12 GND GND 13 PD5 I/O 14 GND GND 15 PD6 I/O 16 GND GND 17 PD7 I/O 18 GND GND 19 ACK# IN 20 GND GND 21 BUSY IN 22 GND GND 23 PE IN 24 GND GND 25 SLCT IN 26 NC Chapter 2 Quick Installation Guide 2-25
EPIC Board EPIC-CV07 Pin Pin Name Signal Type Signal Level 1 DIO7 I/O +5V 2 DIO6 I/O +5V 3 DIO8 I/O +5V 4 DIO5 I/O +5V 5 DIO9 I/O +5V 6 DIO4 I/O +5V 7 DIO10 I/O +5V 8 DIO3 I/O +5V 9 DIO11 I/O +5V 10 GND GND 11 DIO12 I/O 12 GND GND 13 DIO13 I/O 14 GND GND 15 DIO14 I/O 16 GND GND 17 DIO15 I/O 18 GND GND Chapter 2 Quick Installation Guide 2-26 +5V +5V +5V +5V
EPIC Board EPIC-CV07 19 DIO2 I/O +5V 20 GND GND 21 DIO1 I/O 22 GND GND 23 DIO0 I/O 24 GND GND 25 NC 26 +5V +5V +5V PWR +5V Signal Level 2.35 1st LCD Connector (CN17) Pin Pin Name Signal Type 1 BKL_ENABLE OUT 2 BKL_CONTROL OUT 3 LCD_PWR PWR 4 GND GND 5 LVDS_CLK- DIFF 6 LVDS_CLK+ DIFF 7 LCD_PWR PWR 8 GND GND +3.3V/+5V +3.
EPIC Board EPIC-CV07 9 LVDS_DA0- DIFF 10 LVDS_DA0+ DIFF 11 LVDS_DA1- DIFF 12 LVDS_DA1+ DIFF 13 LVDS_DA2-- DIFF 14 LVDS_DA2+ DIFF 15 LVDS_DA3- DIFF 16 LVDS_DA3+ DIFF 17 DDC_DATA I/O +3.3V 18 DDC_CLK I/O +3.3V 19 NC 20 NC 21 NC 22 NC 23 NC 24 NC 25 NC 26 NC 27 LCD_PWR PWR +3.3V/+5V 28 GND GND 29 NC 30 NC Note: LCD_PWR can be set to +3.3V or +5V by JP10.
EPIC Board EPIC-CV07 2.36 1st LCD Inverter Connector (CN18) Pin Pin Name Signal Type Signal Level 1 BKL_PWR PWR +5V / +12V 2 BKL_CONTROL OUT 3 GND GND 4 GND GND 5 BKL_ENABLE OUT +3.3V Note: BKL_PWR can be set to +5V or +12V by JP9. 2.
EPIC Board EPIC-CV07 6 DSR1 IN 7 RTS1 OUT 8 CTS1 IN 9 RI1 IN Pin Pin Name Signal Type 10 DCD2 IN 11 RX2 IN 12 TX2 OUT ±9V 13 DTR2 OUT ±9V 14 GND GND 15 DSR2 IN 16 RTS2 OUT 17 CTS2 IN 18 RI2 IN Pin Pin Name Signal Type Signal Level 10 RS422_TX- OUT ±5V 11 RS422_RX+ IN ±5V 12 RS422_TX+ OUT ±5V 13 RS422_RX- IN ±5V 14 GND GND 15 NC 16 NC ±9V RS-232 Signal Level ±9V RS-422 Chapter 2 Quick Installation Guide 2-30
EPIC Board EPIC-CV07 17 NC 18 RING/+5V/+12V PWR +5V/+12V Pin Pin Name Signal Type Signal Level 10 RS485_D- I/O ±5V 11 NC 12 RS485_D+ I/O ±5V 13 NC 14 GND 15 NC 16 NC 17 NC 18 RING/+5V/+12V RS-485 GND PWR +5V/+12V Note: RING/+5V/+12V can be set to +5V or +12V by JP12. 2.
EPIC Board EPIC-CV07 5 MS_DATA I/O +5V 6 MS_CLK I/O +5V Signal Level 2.
EPIC Board EPIC-CV07 14 VSYNC OUT 15 DDC _CLK I/O +5V Signal Level DVI C5 C1 C2 8 16 24 1 9 17 C3 C4 5 10 15 1 6 11 Pin Pin Name Signal Type 1 TMDS_DAT2- DIFF 2 TMDS_DAT2+ DIFF 3 GND GND 4 NC 5 NC 6 DVI_DDC_CLK I/O +5V 7 DVI_DDC_ DATA I/O +5V 8 VSYNC OUT 9 TMDS_DAT1- DIFF 10 TMDS_DAT1+ DIFF 11 GND GND 12 NC 13 NC 14 +5V PWR 15 GND GND +5V Chapter 2 Quick Installation Guide 2-33
EPIC Board EPIC-CV07 16 HPLG_DETEC IN 17 TMDS_DAT0- DIFF 18 TMDS_DAT0+ DIFF 19 GND GND 20 NC 21 NC 22 GND 23 TMDS_CLK+ DIFF 24 TMDS_CLK- DIFF C1 RED OUT C2 GREEN OUT C3 BLUE OUT C4 HSYNC OUT C5 ANALOG_GND GND 2.
EPIC Board EPIC-CV07 4 RTS8 OUT ±9V 5 TX8 OUT ±9V 6 CTS8 IN 7 DTR8 OUT 8 RI8 IN 9 GND GND ±9V 2.
EPIC Board EPIC-CV07 2.42 6th COM Port Connector (CN24) Pin Pin Name Signal Type Signal Level 1 DCD6 IN 2 DSR6 IN 3 RX6 IN 4 RTS6 OUT ±9V 5 TX6 OUT ±9V 6 CTS6 IN 7 DTR6 OUT 8 RI6 IN 9 GND GND ±9V 2.
EPIC Board EPIC-CV07 2 DSR5 IN 3 RX5 IN 4 RTS5 OUT ±9V 5 TX5 OUT ±9V 6 CTS5 IN 7 DTR5 OUT 8 RI5 IN 9 GND GND ±9V 2.
EPIC Board EPIC-CV07 2.45 3rd COM Port Connector (CN27) Pin Pin Name Signal Type Signal Level 1 DCD3 IN 2 DSR3 IN 3 RX3 IN 4 RTS3 OUT ±9V 5 TX3 OUT ±9V 6 CTS3 IN 7 DTR3 OUT 8 RI3 IN 9 GND GND ±9V 2.
EPIC Board EPIC-CV07 2.47 RIGHT Speaker Connector (CN29) Pin Pin Name Signal Type 1 SKR_R+ OUT 2 SKR_R- OUT Signal Level 2.
EPIC Board EPIC-CV07 2.49 10/100/1000Base-TX Ethernet Connector (LAN2) ACT/LINK LED 8 SPEED LED 1 Pin Pin Name Signal Type 1 MDI0+ DIFF 2 MDI0- DIFF 3 MDI1+ DIFF 4 MDI1- DIFF 5 MDI2+ DIFF 6 MDI2- DIFF 7 MDI3+ DIFF 8 MDI3- DIFF Signal Level 2.50 Mini PCI Express Connector (MINICARD1) Pin Pin Name Signal Type 1 PCIE_WAKE# OUT 2 +3.3VSB PWR 3 NC Chapter 2 Quick Installation Guide 2-40 Signal Level +3.
EPIC Board EPIC-CV07 4 GND GND +5V 5 NC 6 +1.5V PWR +1.5V 7 NC 8 NC 9 GND 10 NC 11 PCIE_REF_CLK- 12 NC 13 PCIE_REF_CLK+ 14 NC 15 GND 16 NC 17 NC 18 GND 19 NC 20 W_DISABLE# IN 21 GND GND 22 PCIE_RST# IN 23 PCIE_RX- DIFF 24 +3.3VSB PWR 25 PCIE_RX+ DIFF 26 GND GND 27 GND GND GND DIFF DIFF GND GND +3.
EPIC Board EPIC-CV07 28 +1.5V PWR 29 GND GND 30 SMB_CLK I/O 31 PCIE_TX- DIFF 32 SMB_DATA I/O 33 PCIE_TX+ DIFF 34 GND GND 35 GND GND 36 USB6_D- DIFF 37 GND GND 38 USB6_D- DIFF 39 +3.3VSB PWR 40 GND GND 41 +3.3VSB PWR 42 NC 43 GND 44 NC 45 NC 46 NC 47 NC 48 +1.5V 49 NC 50 GND 51 NC Chapter 2 Quick Installation Guide 2-42 +1.5V +3.3V +3.3V +3.3V +3.3V GND PWR GND +1.
EPIC Board 52 EPIC-CV07 +3.3VSB PWR +3.3V Note: Either CN9 or MINICARD1 for USB 2.51 Mini PCI Express/ mSATA Connector (MINICARD2) Pin Pin Name Signal Type 1 PCIE_WAKE# OUT 2 +3.3VSB/+3.3V PWR 3 NC 4 GND 5 NC 6 +1.5V 7 NC 8 NC 9 GND 10 NC 11 PCIE_REF_CLK- 12 NC 13 PCIE_REF_CLK+ 14 NC 15 GND Signal Level +3.3V GND PWR +1.
EPIC Board EPIC-CV07 16 NC 17 NC 18 GND 19 NC 20 W_DISABLE# IN 21 GND GND 22 PCIE_RST# IN 23 PCIE_RX-/SATA2_RX+ DIFF 24 +3.3VSB/+3.3V PWR 25 PCIE_RX+/SATA2_RX- DIFF 26 GND GND 27 GND GND 28 +1.5V PWR 29 GND GND 30 SMB_CLK I/O 31 PCIE_TX-/SATA2_TX- DIFF 32 SMB_DATA I/O 33 PCIE_TX+/SATA2_TX+ DIFF 34 GND GND 35 GND GND 36 NC 37 GND 38 NC 39 +3.3VSB/+3.3V Chapter 2 Quick Installation Guide 2-44 GND +1.5V +3.3V +3.3V GND PWR +3.
EPIC Board EPIC-CV07 40 GND GND 41 +3.3VSB/+3.3V PWR 42 NC 43 GND 44 NC 45 NC 46 NC 47 NC 48 +1.5V 49 NC 50 GND 51 NC 52 +3.3VSB/+3.3V +3.3V GND PWR +1.5V GND PWR +3.3V Note 1: Either SATA2 or mSATA,PCI Express for MINICARD2 Note 2: +3.3V by mSATA , +3.3VSB by Mini PCI Express Note 3: No support USB I/F on MINICARD2 2.
EPIC Board EPIC-CV07 4 GND GND 5 SATA1_RX- DIFF 6 SATA1_RX+ DIFF 7 GND GND 2.53 SATA Connector (SATA2) Pin Pin Name Signal Type 1 GND GND 2 SATA2_TX+ DIFF 3 SATA2_TX- DIFF 4 GND GND 5 SATA2_RX- DIFF 6 SATA2_RX+ DIFF 7 GND GND 2.
EPIC Board EPIC-CV07 Pin Pin Name Signal Type Signal Level 1 +5VSB PWR +5V 2 USB0_D- DIFF 3 USB0_D+ DIFF 4 GND GND 5 +5VSB PWR 6 USB1_D- DIFF 7 USB1_D+ DIFF 8 GND GND +5V 2.
EPIC Board EPIC-CV07 2.56 FAN Connector (FAN1) Pin Pin Name Signal Type 1 GND GND 2 +12V PWR 3 FAN_TAC IN Signal Level +12V 2.57 DIMM Connector (DIMM1) Standard DDR3 Connector (204Pins) 2.58 Battery Connector (BT1) Pin Pin Name Signal Type Signal Level 1 +3VBAT PWR +3.
EPIC Board EPIC-CV07 Below Table for China RoHS Requirements 产品中有毒有害物质或元素名称及含量 AAEON Main Board/ Daughter Board/ Backplane 有毒有害物质或元素 部件名称 铅 汞 镉 六价铬 多溴联苯 多溴二苯醚 (Pb) (Hg) (Cd) (Cr(VI)) (PBB) (PBDE) × ○ ○ ○ ○ ○ × ○ ○ ○ ○ ○ 印刷电路板 及其电子组件 外部信号 连接器及线材 O：表示该有毒有害物质在该部件所有均质材料中的含量均在 SJ/T 11363-2006 标准规定的限量要求以下。 X：表示该有毒有害物质至少在该部件的某一均质材料中的含量超出 SJ/T 11363-2006 标准规定的限量要求。 备注：此产品所标示之环保使用期限，系指在一般正常使用状况下。 Chapter 2 Quick Installation Guide 2-49
EPIC Board EPIC-CV07 Chapter 3 AMI BIOS Setup Chapter 3 AMI BIOS Setup 3-1
EPIC Board 3.1 EPIC-CV07 System Test and Initialization These routines test and initialize board hardware. If the routines encounter an error during the tests, you will either hear a few short beeps or see an error message on the screen. There are two kinds of errors: fatal and non-fatal. The system can usually continue the boot up sequence with non-fatal errors. System configuration verification These routines check the current system configuration against the values stored in the CMOS memory.
EPIC Board 3.2 EPIC-CV07 AMI BIOS Setup AMI BIOS ROM has a built-in Setup program that allows users to modify the basic system configuration. This type of information is stored in battery-backed CMOS RAM so that it retains the Setup information when the power is turned off. Entering Setup Power on the computer and press or immediately. This will allow you to enter Setup. Main Set the date, use tab to switch between date elements.
EPIC Board Setup Menu Setup submenu: Main Chapter 3 AMI BIOS Setup 3-4 EPIC-CV07
EPIC Board EPIC-CV07 Setup submenu: Advanced Options Summary : ACPI Settings CPU Configuration IDE Configuration USB Configuration F81866 Super IO Configuration F81866 H/W Monitor S5 RTC Wake Settings System ACPI Parameters. CPU Configuration Parameters IDE Devices Configuration USB Configuration Parameters System Super IO Chip Parameters.
EPIC Board EPIC-CV07 ACPI Settings Options Summary : ACPI Sleep State S3 (Suspend to RAM) Default Select the Highest ACPI sleep state the system will enter when the SUSPEND button is pressed.
EPIC Board EPIC-CV07 CPU Configuration Options Summary : Hyper-Threading Disabled Enabled Default Enabled for Windows XP and Linux (OS optimized for Hyper-Threading Technology) And Disabled for other OS (OS not optimized for Hyper0Threading Technology).
EPIC Board EPIC-CV07 IDE Configuration (IDE) Options Summary : SATA Controller(s) Enabled Default Disabled SATA Ports (0-3) Device Names if Present and Enabled. Configure SATA as IDE Default AHCI Select a configuration for SATA Controller.
EPIC Board EPIC-CV07 IDE Configuration (AHCI) Options Summary : SATA Controller(s) Disabled Enabled Default SATA Ports (0-3) Device Names if Present and Enabled. Configure SATA as IDE AHCI Selected Select a configuration for SATA Controller.
EPIC Board EPIC-CV07 USB Configuration Options Summary : Legacy USB Support Enabled Default Disabled Auto Enable Legacy USB support. AUTO option disables legacy support if no USB devices are connected. DISABLE option will keep USB devices available only for EFI applications. Mass Storage Devices: Auto Default Your Storage Device Floppy Forced FDD Hard Disk CD-ROM Mass storage device emulation type. ‘AUTO’ enumerates devices less than 530 MB as floppies.
EPIC Board EPIC-CV07 F81866 Super IO Configuration Options Summary : Serial Port 1 Configuration Serial Port 2 Configuration Serial Port 3 Configuration Serial Port 4 Configuration Serial Port 5 Configuration Serial Port 6 Configuration Parallel Port Configuration Power Failure F81866 Power Failure ERP Function Set Parameters of Serial Port 1 Set Parameters of Serial Port 2 Set Parameters of Serial Port 3 Set Parameters of Serial Port 4 Set Parameters of Serial Port 5 Set Parameters of Serial Port 6 Se
EPIC Board EPIC-CV07 Serial Port 1 Configuration Options Summary : Serial Port Disabled Enabled Enable or Disable Serial Port (COM) Change Settings Auto (Serial Port 1) IO=3F8h; IRQ=4; IO=3F8h; IRQ=3,4; IO=2F8h; IRQ=3,4’ Select an optimal setting for Super IO device.
EPIC Board EPIC-CV07 Serial Port 2 Configuration Options Summary : Serial Port Disabled Enabled Enable or Disable Serial Port (COM) Change Settings Auto IO=2F8h; IRQ=3; IO=3F8h; IRQ=3,4; IO=2F8h; IRQ=3,4’ Select an optimal setting for Super IO device.
EPIC Board EPIC-CV07 Serial Port 3 Configuration Options Summary : Serial Port Disabled Enabled Enable or Disable Serial Port (COM) Change Settings Auto IO=3E8h; IRQ=11; IO=3E8h; IRQ=11; IO=2E8h; IRQ=11; Select an optimal setting for Super IO device.
EPIC Board EPIC-CV07 Serial Port 4 Configuration Options Summary : Serial Port Disabled Enabled Enable or Disable Serial Port (COM) Change Settings Auto IO=2E8h; IRQ=11; IO=3E8h; IRQ=11; IO=2E8h; IRQ=11; Select an optimal setting for Super IO device.
EPIC Board EPIC-CV07 Serial Port 5 Configuration Options Summary : Serial Port Disabled Enabled Enable or Disable Serial Port (COM) Change Settings Auto IO=2C8h; IRQ=11; IO=2C8h; IRQ=11; IO=2C0h; IRQ=11; Select an optimal setting for Super IO device.
EPIC Board EPIC-CV07 Serial Port 6 Configuration Options Summary : Serial Port Disabled Enabled Enable or Disable Serial Port (COM) Change Settings Auto IO=2C0h; IRQ=11; IO=2C8h; IRQ=11; IO=2C0h; IRQ=11; Select an optimal setting for Super IO device. Device Mode Disable IR1 function Enable IR1 function, active pulse 1.6 uS Enable IR1 function, active pulse 3/16 bit time Change the Serial Port mode.
EPIC Board EPIC-CV07 Parallel Port Configuration Options Summary : Parallel Port Disabled Enabled Default Enable or Disable Parallel Port (LPT/LPTE) Change Settings Auto Default IO=378h; IRQ=5; IO=378h; IRQ=5,6,7,10,11,12; IO=278h; IRQ=5,6,7,10,11,12; IO=3BCh; IRQ=5,6,7,10,11,12; Select an optimal setting for Super IO device. Device Mode STD Printer Mode Default SPP Mode EPP-1.9 and SPP Mode EPP-1.7 and SPP Mode ECP Mode ECP and EPP 1.
EPIC Board EPIC-CV07 ECP and EPP 1.7 Mode Change the Printer Port Mode.
EPIC Board EPIC-CV07 Smart Fan Mode Configuration Option Summary : Fan 1 Smart Fan Control Manual RPM Mode Manual Duty Mode Auto RPM Mode Auto Duty-Cycle Mode Smart Fan Mode select Chapter 3 AMI BIOS Setup 3-20 Default
EPIC Board EPIC-CV07 S5 RTC Wake Settings Option Summary : Wake system with Fixed Disabled Default Time Enabled Enable or disable System wake on alarm event. When enabled, System will wake on the hr::min::sec specified Wake system with Disabled Default Dynamic Time Enabled Enable or disable System wake on alarm event.
EPIC Board Setup submenu: Chipset Options Summary : Host Bridge South Bridge Host Bridge Parameters South Bridge Parameters Chapter 3 AMI BIOS Setup 3-22 EPIC-CV07
EPIC Board EPIC-CV07 Host Bridge Options Summary : Graphics Configuration Graphics Configuration Settings.
EPIC Board EPIC-CV07 Graphics Configuration Options Summary : Fixed Graphics Memory 128M Size 256M Default Configure Fixed Graphics Memory Size IGFX – Boot Type VBIOS Default Default CRT LFP CRT + LFP Select the Video Device which will be activated during POST. This has no effect if external graphics present. This product only supports single display in DOS mode. Active LFP Disabled Enabled Default Select the Active LFP Configuration. No LVDS:VBIOS enables LVDS driver by Integrated encoder.
EPIC Board EPIC-CV07 1024x768 18 bit 1280x768 18 bit Select LCD panel used by Internal Graphics Device by selecting the appropriate setup item.
EPIC Board EPIC-CV07 Options Summary : Power Mode ATX Type AT Type Select power supply mode Azalia Controller Disabled HD Audio Azalia Controller PCI Express Port 0 Disabled Enabled Enable / Disable PCI Express Root Port 0. PCI Express Port 1 Disabled Enabled Auto Enable / Disable PCI Express Root Port 1. PCI Express Port 2 Disabled Enabled Auto Enable / Disable PCI Express Root Port 2. PCI Express Port 3 Disabled Enabled Auto Enable / Disable PCI Express Root Port 3.
EPIC Board EPIC-CV07 Options Summary : Quiet Boot Disabled Enabled Default Enables or disables Quiet Boot option Launch RTL8111E PXE Disabled Default OpROM Enabled Enable or Disable Legacy Boot Option for RTL8111E Boot options #X Your storage/disk devices Sets the system boot order Hard Drives BBS Priorities Chapter 3 AMI BIOS Setup 3-27
EPIC Board EPIC-CV07 Submenu: Security Change User/Supervisor Password You can install a Supervisor password, and if you install a supervisor password, you can then install a user password. A user password does not provide access to many of the features in the Setup utility. If you highlight these items and press Enter, a dialog box appears which lets you enter a password. You can enter no more than six letters or numbers. Press Enter after you have typed in the password.
EPIC Board EPIC-CV07 Setup submenu: Exit Chapter 3 AMI BIOS Setup 3-29
EPIC Board EPIC-CV07 Chapter 4 Driver Installation .
EPIC Board EPIC-CV07 The EPIC-CV07 comes with an AutoRun CD-ROM that contains all drivers and utilities that can help you to install the driver automatically. Insert the driver CD, the driver CD-title will auto start and show the installation guide. If not, please follow the sequence below to install the drivers.
EPIC Board 4.1 EPIC-CV07 Installation: Insert the EPIC-CV07 CD-ROM into the CD-ROM drive. And install the drivers from Step 1 to Step 7 in order. Step 1 – Install Chipset Driver 1. Click on the Step1 - Chipset folder and double click on the infinst_autol.exe file 2. Follow the instructions that the window shows 3. The system will help you install the driver automatically Step 2 – Install VGA Driver 1. Click on the Step2 - VGA folder and double click on the Setup.exe file 2.
EPIC Board EPIC-CV07 2. Double click on the .exe file located in each OS folder 3. Follow the instructions that the window shows 4. The system will help you install the driver automatically Step 5 – Install Touch Driver 1. Click on the Step5 - TOUCH folder and double click on the Setup.exe file 2. Follow the instructions that the window shows 3. The system will help you install the driver automatically Step 6 – Serial Port Driver (Optional) For Windows® XP: 1.
EPIC Board EPIC-CV07 For Windows® 7: 1. Create a password for Administrator account. 2.
EPIC Board 3. EPIC-CV07 Reboot and Administrator login. 4. To run patch.bat with [Run as administrator].
EPIC Board EPIC-CV07 Step 7 – Install Rapid Storage Technology Driver 1. Click on the Step7 - Rapid Storage Technology folder and double click on the setup.exe file 2. Follow the instructions that the window shows 3.
EPIC Board EPIC-CV07 Appendix A Programming the Watchdog Timer Appendix A Programming the Watchdog Timer A-1
EPIC Board EPIC-CV07 A.1 Watchdog Timer Initial Program Table 1 : SuperIO relative register table Default Value Index 0x2E(Note1) Data 0x2F(Note2) Note SIO MB PnP Mode Index Register 0x2E or 0x4E SIO MB PnP Mode Data Register 0x2F or 0x4F Table 2 : Watchdog relative register table LDN Register BitNum Value Note Time of watchdog timer Timer Counter 0x07(Note3) 0xF6(Note4) (Note24) (0~255) This register is byte access Select time unit.
EPIC Board EPIC-CV07 ************************************************************************************ // SuperIO relative definition (Please reference to Table 1) #define byte SIOIndex #define byte SIOData //This parameter is represented from Note1 //This parameter is represented from Note2 #define void IOWriteByte(byte IOPort, byte Value); #define byte IOReadByte(byte IOPort); // Watch Dog relative definition (Please reference to Table 2) #define byte TimerLDN //This parameter is represe
EPIC Board EPIC-CV07 ************************************************************************************ VOID Main(){ // Procedure : AaeonWDTConfig // (byte)Timer : Time of WDT timer.(0x00~0xFF) // (boolean)Unit : Select time unit(0: second, 1: minute). AaeonWDTConfig(); // Procedure : AaeonWDTEnable // This procudure will enable the WDT counting.
EPIC Board EPIC-CV07 ************************************************************************************ // Procedure : AaeonWDTEnable VOID AaeonWDTEnable (){ WDTEnableDisable(EnableLDN, EnableReg, EnableBit, 1); } // Procedure : AaeonWDTConfig VOID AaeonWDTConfig (){ // Disable WDT counting WDTEnableDisable(EnableLDN, EnableReg, EnableBit, 0); // Clear Watchdog Timeout Status WDTClearTimeoutStatus(); // WDT relative parameter setting WDTParameterSetting(); } VOID WDTEnableDisable(byte LDN, byte Reg
EPIC Board EPIC-CV07 ************************************************************************************ VOID SIOEnterMBPnPMode(){ IOWriteByte(SIOIndex, 0x87); IOWriteByte(SIOIndex, 0x87); } VOID SIOExitMBPnPMode(){ IOWriteByte(SIOIndex, 0xAA); } VOID SIOSelectLDN(byte LDN){ IOWriteByte(SIOIndex, 0x07); // SIO LDN Register Offset = 0x07 IOWriteByte(SIOData, LDN); } VOID SIOBitSet(byte LDN, byte Register, byte BitNum, byte Value){ Byte TmpValue; SIOEnterMBPnPMode(); SIOSelectLDN(byte LDN); IOWriteB
EPIC Board EPIC-CV05 Appendix B I/O Information Appendix B I/O Information B - 1
EPIC Board B.
EPIC Board EPIC-CV05 Appendix B I/O Information B - 3
EPIC Board B.
EPIC Board EPIC-CV05 B.
EPIC Board Appendix B I/O Information B - 6 EPIC-CV05
EPIC Board EPIC-CV05 B.
EPIC Board EPIC-CV07 Appendix C Mating Connector Appendix C Mating Connector C - 1
EPIC Board EPIC-CV07 C.1 List of Mating Connectors and Cables The table notes mating connectors and available cables.
EPIC Board CN16 CN17 CN18 CN19 CN20 CN21 CN22 CN23 CN24 CN25 CN26 CN27 CN28 CN29 LPT/Digital I/O Connector 1st LCD Connector 1st LCD Inverter Connector 1st /2nd Serial COM Port Connector PS2 Keyboard / Mouse Connector DVI-I/CRT Connector 8th COM Port Connector 7th COM Port Connector 6th COM Port Connector 5th COM Port Connector 4th COM Port Connector 3th COM Port Connector Left Speaker Connector Right Speaker Connector Molex EPIC-CV07 51110-2650 Parallel Cable 1701260200 HIROSE DF13-20S-1
EPIC Board LAN1 10 /100 /1000 Base-Tx Ethernet Connector LAN2 10 /100 /1000 Base-Tx Ethernet Connector MINICARD Mini PCI 1 Express Connector MINICARD Mini PCI 2 Express/mS ATA Connector SATA1 SATA Connector SATA2 SATA Connector USB1 Stack USB Connector USB2 Stack USB Connector FAN1 FAN Connector DIMM1 DIMM Connector BT1 Battery Connector EPIC-CV07 Neltron 7001-8P8C N/A N/A Neltron 7001-8P8C N/A N/A N/A N/A N/A N/A N/A N/A N/A N/A Molex 67582-0000 SATA Cable 1709070500 Molex 67582-00
EPIC Board EPIC-CV07 Appendix D Electrical Specifications for I/O Ports Appendix D Electrical Specifications for I/O Ports D-1
EPIC Board EPIC-CV07 D.1 DIO Programming EPIC-CV07 utilizes FINTEK 81866 chipset as its Digital I/O controller. Below are the procedures to complete its configuration and the AAEON initial watchdog timer program is also attached based on which you can develop customized program to fit your application. There are three steps to complete the configuration setup: (1) Enter the MB PnP Mode; (2) Modify the data of configuration registers; (3) Exit the MB PnP Mode.
EPIC Board EPIC-CV07 D.
EPIC Board EPIC-CV07 Table 4 : Digital Input relative register table LDN Register BitNum 0x06(Note59) 0x8A(Note60) 0(Note61) GPIO80 DIO‐9 Pin Status 0x06(Note62) 0x8A(Note63) 1(Note64) GPIO81 DIO‐10 Pin Status 0x06(Note65) 0x8A(Note66) 2(Note67) GPIO82 DIO‐11 Pin Status 0x06(Note68) 0x8A(Note69) 3(Note70) GPIO83 DIO‐12 Pin Status 0x06(Note71) 0x8A(Note72) 4(Note73) GPIO84 DIO‐13 Pin Status 0x06(Note74) 0x8A(Note75) 5(Note76) GPIO85 DIO‐14 Pin Status 0x06(Note77) 0x8A(Note
EPIC Board EPIC-CV07 D.
EPIC Board EPIC-CV07 ************************************************************************************ // Digital Output control relative definition (Please reference to Table 3) #define byte DOutput1LDN // This parameter is represented from Note27 #define byte DOutput1Reg // This parameter is represented from Note28 #define byte DOutput1Bit // This parameter is represented from Note29 #define byte DOutput1Val // This parameter is represented from Note30 #define byte DOutput2LDN // This p
EPIC Board EPIC-CV07 ************************************************************************************ // Digital Input Status relative definition (Please reference to Table 4) #define byte DInput9LDN // This parameter is represented from Note59 #define byte DInput9Reg // This parameter is represented from Note60 #define byte DInput9Bit #define byte DInput10LDN // This parameter is represented from Note61 // This parameter is represented from Note62 #define byte DInput10Reg // This paramet
EPIC Board EPIC-CV07 ************************************************************************************ // Digital Output control relative definition (Please reference to Table 5) #define byte DOutput9LDN // This parameter is represented from Note83 #define byte DOutput9Reg // This parameter is represented from Note84 #define byte DOutput9Bit // This parameter is represented from Note85 #define byte DOutput9Val // This parameter is represented from Note86 #define byte DOutput10LDN // This
EPIC Board EPIC-CV07 ************************************************************************************ VOID Main(){ Boolean PinStatus ; // Procedure : AaeonReadPinStatus // Input : // Example, Read Digital I/O Pin 3 status // Output : // InputStatus : // 0: Digital I/O Pin level is low // 1: Digital I/O Pin level is High PinStatus = AaeonReadPinStatus(DInput3LDN, DInput3Reg, DInput3Bit); // Procedure : AaeonSetOutputLevel // Input : // Example, Set Digital I/O Pin 6 level AaeonSetOutputLevel
EPIC Board EPIC-CV07 ************************************************************************************ Boolean AaeonReadPinStatus(byte LDN, byte Register, byte BitNum){ Boolean PinStatus ; PinStatus = SIOBitRead(LDN, Register, BitNum); Return PinStatus ; } VOID AaeonSetOutputLevel(byte LDN, byte Register, byte BitNum, byte Value){ ConfigToOutputMode(LDN, Register, BitNum); SIOBitSet(LDN, Register, BitNum, Value); } ************************************************************************************
EPIC Board EPIC-CV07 ************************************************************************************ VOID SIOEnterMBPnPMode(){ IOWriteByte(SIOIndex, 0x87); IOWriteByte(SIOIndex, 0x87); } VOID SIOExitMBPnPMode(){ IOWriteByte(SIOIndex, 0xAA); } VOID SIOSelectLDN(byte LDN){ IOWriteByte(SIOIndex, 0x07); // SIO LDN Register Offset = 0x07 IOWriteByte(SIOData, LDN); } VOID SIOBitSet(byte LDN, byte Register, byte BitNum, byte Value){ Byte TmpValue; SIOEnterMBPnPMode(); SIOSelectLDN(byte LDN); IOWriteB
EPIC Board EPIC-CV07 ************************************************************************************ Boolean SIOBitRead(byte LDN, byte Register, byte BitNum){ Byte TmpValue; SIOEnterMBPnPMode(); SIOSelectLDN(LDN); IOWriteByte(SIOIndex, Register); TmpValue = IOReadByte(SIOData); TmpValue &= (1 << BitNum); SIOExitMBPnPMode(); If(TmpValue == 0) Return 0; Return 1; } VOID ConfigToOutputMode(byte LDN, byte Register, byte BitNum){ Byte TmpValue, OutputEnableReg; OutputEnableReg = Register‐1; SIOEnterMBP
