EPIC Board EPIC-HD07 EPIC-HD07 ® AMD G-series T56N/T44R/T40R Processor Onboard DDR3 1066/1333 SODIMM 18/24-bit Single/Dual-channel LVDS LCD 8 USB 2.0, 6 COM, 1 SATA, 1 mSATA 2 GbE, PCI-104, Mini Card EPIC-HD07 Manual Rev. A 2nd Ed.
EPIC Board EPIC-HD07 Copyright Notice This document is copyrighted, 2012. All rights are reserved. The original manufacturer reserves the right to make improvements to the products described in this manual at any time without notice. No part of this manual may be reproduced, copied, translated, or transmitted in any form or by any means without the prior written permission of the original manufacturer. Information provided in this manual is intended to be accurate and reliable.
EPIC Board EPIC-HD07 Acknowledgments All other products’ name or trademarks are properties of their respective owners. AMD® is trademark of Advanced Micro Devices. Microsoft Windows is a registered trademark of Microsoft Corp. ITE is a trademark of Integrated Technology Express, Inc. IBM, PC/AT, PS/2, and VGA are trademarks of International Business Machines Corporation. ® All other product names or trademarks are properties of their respective owners.
EPIC Board EPIC-HD07 Packing List Before you begin installing your card, please make sure that the following materials have been shipped: 1709070500 SATA Cable 1702150155 SATA Power Cable 9657666600 Jumper Cap Product DVD EPIC-HD07 If any of these items are missing or damaged, please contact your distributor or sales representative immediately.
EPIC Board EPIC-HD07 Contents Chapter 1 General Information 1.1 Introduction................................................................... 1-2 1.2 Features ....................................................................... 1-3 1.3 Specifications ............................................................... 1-4 Chapter 2 Quick Installation Guide 2.1 Safety Precautions ....................................................... 2-2 2.2 Location of Connectors and Jumpers ..........................
EPIC Board EPIC-HD07 2.18 LVDS Connector (CN2)............................................ 2-18 2.19 LPC Connector (CN3) .............................................. 2-19 2.20 1st Backlight Connector (CN4)................................. 2-22 2.21 2nd Backlight Connector (CN5) ............................... 2-23 2.22 SATA Power Connector (CN6) ................................ 2-23 2.23 Audio Connector (CN7)............................................ 2-24 2.24 Touch Screen Connector (CN8).............
EPIC Board EPIC-HD07 2.43 LPT Port Connector (LPT1) ..................................... 2-41 2.44 Battery Connector (BT1) .......................................... 2-42 2.45 PS/2 Keyboard and Mouse Connector (KB1) .......... 2-43 2.46 LAN Ethernet RJ-45 Connector (LAN1) ................... 2-43 2.47 LAN Ethernet RJ-45 Connector (LAN2) ................... 2-44 2.48 VGA & DVI-I Connector (DVI+VGA3) ...................... 2-44 2.49 SATA Connector (SATA1) .......................................
EPIC Board EPIC-HD07 Appendix D AHCI Setting D.1 Setting AHCI .............................................................D-2 Appendix E Electrical Specifications for I/O Ports E.1 Electrical Specifications for I/O Ports........................
EPIC Board EPIC-HD07 Chapter 1 General Information Chapter 1 General Information 1- 1
EPIC Board EPIC-HD07 1.1 Introduction AAEON announces a brand new EPIC Board EPIC-HD07, designed to fit in diverse applications that demand for fitting in different space limitations and high performance. EPIC-HD07 accommodates T56N/T44R/T40R Processor onboard and AMD® features 1066/1333 system memory up to 4GB. DDR3 G-series™ SODIMM Moreover, EPIC-HD07 ® adopts AMD A55E chipset to achieve an excellent performance.
EPIC Board EPIC-HD07 1.2 Features AMD® G-series™ T56N/T44R/T40R Processor AMD® A55E DDR3 SOGIMM 1066/1333 (T56N) Memory Up to 4 GB Gigabit Ethernet x 2 18/24-bit Dual/Single Channel LVDS LCD, DVI (Optional) 2CH AC97 2.3 Codec Audio mSATA x 1, SATA x 1 USB 2.0 x 8, COM x 6, 16-bit Digital I/O Co-lay With LPT PCI-104, Mini Card Expansions DC 12V CPU And PCH On The Solder Side for Better Heat Spreading PCB 1.
EPIC Board EPIC-HD07 1.
EPIC Board EPIC-HD07 Operation Temperature 32°F ~ 140°F (0°C ~ 60°C) Storage Temperature -40°F ~ 176°F (-40°C ~ 80°C) Operation Humidity 0% ~ 90% relative humidity, non-condensing Display: Supports CRT/LCD/DVI simultaneous/ dual view displays Chipset AMD® G-series CPU integrated Resolutions Up to 2560 x 1600 T56N(18W) 1920 x 1200 T44R/T40R (9W/5.
EPIC Board EPIC-HD07 Audio Line-in, Line-out, & Mic-in Touch Screen Supports 4/5-wire resistive touch screen (optional) Chapter 1 General Information 1- 6
EPIC Board EPIC-HD07 Chapter 2 Quick Installation Guide Chapter 2 Quick Installation Guide 2-1
EPIC Board EPIC-HD07 2.1 Safety Precautions Always completely disconnect the power cord from your board whenever you are working on it. Do not make connections while the power is on, because a sudden rush of power can damage sensitive electronic components. Always ground yourself to remove any static charge before touching the board. Modern electronic devices are very sensitive to static electric charges. Use a grounding wrist strap at all times.
EPIC Board EPIC-HD07 2.
EPIC Board Solder Side Chapter 2 Quick Installation Guide 2-4 EPIC-HD07
EPIC Board EPIC-HD07 2.
EPIC Board Solder Side Chapter 2 Quick Installation Guide 2-6 EPIC-HD07
EPIC Board EPIC-HD07 Heatsink 3 .0 3 .0 e b e e c b a b a a b a b * 3 .
EPIC Board EPIC-HD07 2.4 List of Jumpers The board has a number of jumpers that allow you to configure your system to suit your application.
EPIC Board EPIC-HD07 2.5 List of Connectors The board has a number of connectors that allow you to configure your system to suit your application.
EPIC Board EPIC-HD07 USB3 USB Connector USB4 USB Connector USB5 USB Connector USB6 USB Connector COM1 (Dual Port 1) COM1 RS-232 Serial Port Connector COM2 (Dual Port 2) COM2 RS-232/422/485 Serial Port Connector COM3 COM3 RS-232 Serial Port Connector COM4 COM4 RS-232 Serial Port Connector COM5 COM5 RS-232 Serial Port Connector COM6 COM6 RS-232 Serial Port Connector LPT1 LPT Port Connector SATA1 SATA Connector BT1 Battery Connector KB1 PS/2 Keyboard/Mouse Connector Chapter 2 Quic
EPIC Board EPIC-HD07 2.6 Setting Jumpers You configure your card to match the needs of your application by setting jumpers. A jumper is the simplest kind of electric switch. It consists of two metal pins and a small metal clip (often protected by a plastic cover) that slides over the pins to connect them. To “close” a jumper you connect the pins with the clip. To “open” a jumper you remove the clip. Sometimes a jumper will have three pins, labeled 1, 2 and 3.
EPIC Board EPIC-HD07 2.7 AT/ATX Selection (JP1) ATX AT JP1 Function ATX OFF (Default) AT ON 2.8 COM2 Ring/+5V/+12V Selection (JP2) +12V RI2# +5V JP2 Function 1-2 +12V 3-4 RI2#_SEL (Default) 5-6 +5V 2.
EPIC Board EPIC-HD07 2.10 LCD Panel Voltage Selection (JP4) LVDS1 +5V JP4 Function 1-3 +5V 3-5 +3.3V (Default) LVDS2 +3.3V +5V JP4 Function 2-4 +5V 4-6 +3.3V (Default) 2.
EPIC Board JP5 Function 1-3 Voltage Mode 3-5 PWM Mode(Default) EPIC-HD07 LVDS2 1 3 5 2 4 6 Voltage-mode 1 3 5 2 4 6 PWM-mode JP5 Function 2-4 Voltage Mode 4-6 PWM Mode(Default) 2.
EPIC Board JP6 Function 2-4 +5V 4-6 +12V (Default) EPIC-HD07 2.13 Clear CMOS (JP7) 1 2 3 Normal 1 2 3 Clear CMOS JP7 Function 1-2 Protected (Default) 2-3 Clear 2.14 DDR3/DDR3L Voltage Control (JP8) DDR3 DDR3L JP8 Function OFF DDR3 (Default) ON DDR3L 2.15 PC/104+ (PCI-104) I/O Voltage Selection (JP9) +5V +3.
EPIC Board JP9 Function 1-2 +5V 2-3 +3.3V (Default) EPIC-HD07 2.16 Touch Screen Connector Selection (JP10) 5-Wire 4-Wire JP10 Function ON 4-Wire (Default) OFF 5-Wire 2.17 LVDS Connector (CN1) Pin Pin Name Signal Type 1 LVDS_BKLEN OUT 2 LVDS_BKLCTL OUT 3 LCD_PWR PWR 4 GND GND 5 LVDS_TXLCLK# OUT 6 LVDS_TXLCLK OUT Chapter 2 Quick Installation Guide 2-16 Signal Level +3.
EPIC Board EPIC-HD07 +3.3V/ 5V 7 LCD_PWR PWR 8 GND GND 9 LVDS_TXL0# OUT 10 LVDS_TXL0 OUT 11 LVDS_TXL1# OUT 12 LVDS_TXL1 OUT 13 LVDS_TXL2# OUT 14 LVDS_TXL2 OUT 15 LVDS_TXL3# OUT 16 LVDS_TXL3 OUT 17 LVDS_DDCPDATA I/O +3.3V 18 LVDS_DDCPCLK I/O +3.3V 19 N.C - 20 N.C - 21 N.C - 22 N.C - 23 N.C - 24 N.C - 25 N.C - 26 N.C - 27 LCD_PWR PWR 28 GND GND 29 N.C - 30 N.C - +3.
EPIC Board EPIC-HD07 2.18 LVDS Connector (CN2) Pin Pin Name Signal Type 1 LVDS_BKLEN OUT 2 LVDS_BKLCTL OUT 3 LCD_PWR PWR 4 GND GND 5 LVDS_TXLCLK# OUT 6 LVDS_TXLCLK OUT 7 LCD_PWR PWR 8 GND GND 9 LVDS_TXL0# OUT 10 LVDS_TXL0 OUT 11 LVDS_TXL1# OUT 12 LVDS_TXL1 OUT 13 LVDS_TXL2# OUT 14 LVDS_TXL2 OUT 15 LVDS_TXL3# OUT 16 LVDS_TXL3 OUT 17 LVDS_DDCPDATA I/O Chapter 2 Quick Installation Guide 2-18 Signal Level +3.3V/ 5V +3.3V/ 5V +3.
EPIC Board EPIC-HD07 18 LVDS_DDCPCLK I/O +3.3V 19 LVDS_TXU0# OUT - 20 LVDS_TXU0 OUT - 21 LVDS_TXU1# OUT - 22 LVDS_TXU1 OUT - 23 LVDS_TXU2# OUT - 24 LVDS_TXU2 OUT - 25 LVDS_TXU3# OUT - 26 LVDS_TXU3 OUT - 27 LCD_PWR PWR 28 GND GND 29 LVDS_TXUCLK# OUT - 30 LVDS_TXUCLK OUT - +3.3V/ 5V 2.
EPIC Board EPIC-HD07 Pin Pin Name Signal Type 1 LAD0 I/O 2 LAD1 I/O 3 LAD2 I/O 4 LAD3 I/O 5 +3.3V PWR 6 LFRAME# OUT 7 LPC_RST# OUT 8 GND GND 9 LPC_CLK33 OUT 10 LDRQ#0 OUT 11 LDRQ#1 OUT 12 SERIRQ OUT Signal Level +3.
EPIC Board EPIC-HD07 10 GND GND 11 GPIO4 I/O 12 GND GND 13 GPIO5 I/O 14 GND GND 15 GPIO6 I/O 16 GND GND 17 GPIO7 I/O 18 GPIO6 I/O 19 GPIO10 I/O 20 GND GND 21 GPIO9 I/O 22 GND GND 23 GPIO8 I/O 24 GND GND 25 N.C 26 N.C NO.
EPIC Board EPIC-HD07 6 GPIO5 13 7 GPIO6 15 8 GPIO7 17 9 GPIO8 23 10 GPIO9 21 11 GPIO10 19 12 GPIO11 8 13 GPIO12 6 14 GPIO13 4 15 GPIO14 2 16 GPIO15 1 2.
EPIC Board EPIC-HD07 2.21 2nd Backlight Connector (CN5) Pin Pin Name Signal Type 1 LVDS Backlight PWR OUT 2 LVDS Backlight control OUT 3 GND GND 4 GND GND 5 LVDS Backlight Enable OUT Signal Level 2.
EPIC Board EPIC-HD07 2.
EPIC Board EPIC-HD07 2.24 Touch Screen Connector (CN8) Pin Pin Name Signal Type 1 GND GND 2 Top Excite IN 3 Bottom Excite IN 4 Left Excite IN 5 Right Excite IN 6 Top Sense IN 7 Bottom Sense IN 8 Left Sense IN 9 Right Sense IN Signal Level 2.
EPIC Board EPIC-HD07 Pin Pin Name Signal Type Signal Level 1 +12V PWR +12V 2 GND GND 2.
EPIC Board EPIC-HD07 2.27 ATX 4-Pin Power Connector (CN11) Pin Pin Name Signal Type Signal Level 1 GND GND 2 GND GND 3 +12V PWR +12V 4 +12V PWR +12V Signal Level 2.28 Fan Connector (CN12) Pin Pin Name Signal Type 1 GND GND 2 Fan Power Control OUT 3 Fan In OUT 2.
EPIC Board EPIC-HD07 Pin Pin Name Signal Type 1 Power Button(+) IN 2 Power Button(-) IN 3 External Buzzer(+) OUT 4 External Buzzer(-) OUT 5 IDE LED(+) OUT 6 IDE LED(-) OUT 7 Power LED(+) OUT 8 Power LED(-) OUT 9 Reset Switch(+) IN 10 Reset Switch(-) IN Signal Level 2.30 PCI-Express Mini Card Connector (CN14) Pin Pin Name Signal Type 1 PCIE_WAKE_UP# I/O 2 MINI1_3.
EPIC Board EPIC-HD07 6 1.5V PWR 7 PCIE_CLKREQ# I/O 8 Reserved 9 GND 10 Reserved 11 PCIE_MINI1_100M# 12 Reserved 13 PCIE_MINI1_100M 14 Reserved 15 GND 16 Reserved 17 Reserved 18 Reserved 19 Reserved 20 MINI_CARD_EN 21 GND 22 MINI_RST# 23 MINI_CARD1_RXN DIFF 24 MINI1_3.3V PWR 25 MINI_CARD1_RXP DIFF 26 GND GND 27 GND GND 28 1.5V PWR 29 GND GND 1.5V GND OUT OUT GND GND 1.
EPIC Board EPIC-HD07 30 SMB_CLK I/O 31 MINI_CARD1_TXN DIFF 32 SMB_DATA I/O 33 MINI_CARD1_TXP DIFF 34 GND GND 35 GND GND 36 USBN2 DIFF 37 GND GND 38 USBP2 DIFF 39 MINI1_3.3V PWR 40 GND GND 41 MINI1_3.3V PWR 42 Reserved 43 NC 44 Reserved 45 VENDOR 46 Reserved 47 Reserved I/O 48 1.5V PWR 49 DA/DSS I/O 50 GND GND 51 PRESENT DETECTION I/O 52 MINI1_3.3V PWR Chapter 2 Quick Installation Guide 2-30 3.3V 3.3V I/O 1.5V 3.
EPIC Board EPIC-HD07 2.31 mSATA Mini Card Connector (CN15) Pin Pin Name Signal Type 1 PCIE_WAKE_UP# I/O 2 MINI2_3.3V PWR 3 Reserved 4 GND 5 Reserved 6 1.5V PWR 7 PCIE_CLKREQ# I/O 8 Reserved 9 GND 10 Reserved 11 PCIE_MINI2_100M# 12 Reserved 13 PCIE_MINI2_100M 14 Reserved 15 GND 16 Reserved Signal Level 3.3V GND 1.
EPIC Board EPIC-HD07 17 Reserved 18 Reserved 19 Reserved 20 MINI_CARD_EN 21 GND 22 MINI_RST# 23 SATA_RX1_P DIFF 24 MINI2_3.3V PWR 25 SATA_RX1_N DIFF 26 GND GND 27 GND GND 28 1.5V PWR 29 GND GND 30 SMB_CLK I/O 31 SATA_TX1_N DIFF 32 SMB_DATA I/O 33 SATA_TX1_P DIFF 34 GND GND 35 GND GND 36 USBN6 DIFF 37 GND GND 38 USBP6 DIFF 39 MINI2_3.3V PWR 40 GND GND Chapter 2 Quick Installation Guide 2-32 GND 1.5V 3.
EPIC Board EPIC-HD07 41 MINI2_3.3V PWR 3.3V 42 Reserved 43 NC 44 Reserved 45 Reserved 46 Reserved 47 Reserved I/O 48 1.5V PWR 49 Reserved I/O 50 GND GND 51 Reserved I/O 52 MINI2_3.3V PWR 3.3V I/O 1.5V 2.
EPIC Board EPIC-HD07 4 GND GND 5 +5VSB PWR 6 USBD2- OUT 7 USBD2+ OUT 8 GND GND +5V 2.
EPIC Board EPIC-HD07 2.34 USB Connector (USB5) Pin Pin Name Signal Type Signal Level 1 +5VSB PWR +5V 2 USBD5- OUT 3 USBD5+ OUT 4 GND GND 5 GND GND 2.
EPIC Board EPIC-HD07 2.36 USB Connector (USB7) Pin Pin Name Signal Type Signal Level 1 +5VSB PWR +5V 2 USBD7- OUT 3 USBD7+ OUT 4 GND GND 5 GND GND 2.
EPIC Board EPIC-HD07 2.
EPIC Board EPIC-HD07 16 RTS#2 OUT 17 CTS#2 IN 18 RI#2 IN 2.
EPIC Board EPIC-HD07 2.40 RS-232 Serial Port Connector (COM4) Pin Pin Name Signal Type 1 DCD#4 IN 2 DSR#4 IN 3 RXD4 IN 4 RTS#4 OUT 5 TXD4 OUT 6 CTS#4 IN 7 DTR#4 OUT 8 RI#4 IN 9 GND GND Signal Level 2.
EPIC Board EPIC-HD07 Pin Pin Name Signal Type 1 DCD#5 IN 2 DSR#5 IN 3 RXD5 IN 4 RTS#5 OUT 5 TXD5 OUT 6 CTS#5 IN 7 DTR#5 OUT 8 RI#5 IN 9 GND GND Signal Level 2.
EPIC Board EPIC-HD07 6 CTS#6 IN 7 DTR#6 OUT 8 RI#6 IN 9 GND GND 2.
EPIC Board EPIC-HD07 12 GND GND 13 DATA5 I/O 14 GND GND 15 DATA6 I/O 16 GND GND 17 DATA7 I/O 18 GND GND 19 #ACK I/O 20 GND GND 21 BUSY I/O 22 GND GND 23 PE I/O 24 SELECT I/O 25 GND GND 26 N.C 2.
EPIC Board EPIC-HD07 2.45 PS/2 Keyboard and Mouse Connector (KB1) Pin Pin Name Signal Type 1 KBDATA OUT 2 KBCLK OUT 3 GND GND 4 +5V PWR 5 MSDATA OUT 6 MSCLK OUT Signal Level +5V 2.46 LAN Ethernet RJ-45 Connector (LAN1) ACT/LINK LED 8 SPEED LED 1 Pin Pin Name Signal type 1 LAN1_MDIP0 DIFF. 2 LAN1_MDIN0 DIFF. 3 LAN1_MDIP1 DIFF. 4 LAN1_MDIN1 DIFF. 5 LAN1_MDIP2 DIFF.
EPIC Board EPIC-HD07 6 LAN1_MDIN2 DIFF. 7 LAN1_MDIP3 DIFF. 8 LAN1_MDIN3 DIFF. 2.47 LAN Ethernet RJ-45 Connector (LAN2) ACT/LINK LED 8 SPEED LED 1 Pin Pin Name Signal Type 1 LAN2_MDIP0 DIFF. 2 LAN2_MDIN0 DIFF. 3 LAN2_MDIP1 DIFF. 4 LAN2_MDIN1 DIFF. 5 LAN2_MDIP2 DIFF. 6 LAN2_MDIN2 DIFF. 7 LAN2_MDIP3 DIFF. 8 LAN2_MDIN3 DIFF. 2.
EPIC Board EPIC-HD07 VGA Pin Pin Name Signal Type 1 RED I/O 2 GREEN I/O 3 BLUE I/O 4 NC 5 GND GND 6 GND GND 7 GND GND 8 GND GND 9 VGA_5V PWR 10 CRT_PLUG IN 11 NC 12 DDC_SDA I/O 13 HSYNC I/O 14 VSYNC I/O 15 DDC_SCL I/O Pin Pin Name Signal Type 1 DVI_TX2_N I/O 2 DVI_TX2_P DVI_TX2_P 3 GND GND 4 NC NC 5 NC NC Signal Level 5V DVI Signal Level Chapter 2 Quick Installation Guide 2-45
EPIC Board EPIC-HD07 6 DVI_AUXP DVI_AUXP 7 DVI_AUXN I/O 8 VSYNC VSYNC 9 DVI_TX1_P I/O 10 DVI_TX1_N DVI_TX1_N 11 GND GND 12 NC NC 13 NC NC 14 VGA_5V VGA_5V 15 GND GND 16 DVI_HPD DVI_HPD 17 DVI_TX0_N I/O 18 DVI_TX0_P DVI_TX0_P 19 GND GND 20 NC NC 21 NC NC 22 GND GND 23 DVI_CLK_P I/O 24 DVI_CLK_N DVI_CLK_N C1 RED I/O C2 GREEN GREEN C3 BLUE I/O C4 HSYNC HSYNC C5 GND GND Chapter 2 Quick Installation Guide 2-46 5V
EPIC Board EPIC-HD07 2.
EPIC Board EPIC-HD07 Below Table for China RoHS Requirements 产品中有毒有害物质或元素名称及含量 AAEON Main Board/ Daughter Board/ Backplane 有毒有害物质或元素 部件名称 铅 汞 镉 六价铬 多溴联苯 多溴二苯醚 (Pb) (Hg) (Cd) (Cr(VI)) (PBB) (PBDE) × ○ ○ ○ ○ ○ × ○ ○ ○ ○ ○ 印刷电路板 及其电子组件 外部信号 连接器及线材 O：表示该有毒有害物质在该部件所有均质材料中的含量均在 SJ/T 11363-2006 标准规定的限量要求以下。 X：表示该有毒有害物质至少在该部件的某一均质材料中的含量超出 SJ/T 11363-2006 标准规定的限量要求。 备注：此产品所标示之环保使用期限，系指在一般正常使用状况下。 Chapter 2 Quick Installation Guide 2-48
EPIC Board EPIC-HD07 Chapter 3 AMI BIOS Setup Chapter 3 AMI BIOS Setup 3-1
EPIC Board 3.1 EPIC-HD07 System Test and Initialization These routines test and initialize board hardware. If the routines encounter an error during the tests, you will either hear a few short beeps or see an error message on the screen. There are two kinds of errors: fatal and non-fatal. The system can usually continue the boot up sequence with non-fatal errors. System configuration verification These routines check the current system configuration against the values stored in the CMOS memory.
EPIC Board 3.2 EPIC-HD07 AMI BIOS Setup AMI BIOS ROM has a built-in Setup program that allows users to modify the basic system configuration. This type of information is stored in battery-backed CMOS RAM so that it retains the Setup information when the power is turned off. Entering Setup Power on the computer and press or immediately. This will allow you to enter Setup. Main Set the date, use tab to switch between date elements.
EPIC Board EPIC-HD07 Advanced Advanced BIOS Features Setup including TPM, ACPI, etc. Chipset Host bridge parameters.
EPIC Board EPIC-HD07 Boot Enables/disable quiet boot option. Security Set setup administrator password.
EPIC Board EPIC-HD07 Save&Exit Exit system setup after saving the changes.
EPIC Board EPIC-HD07 Chapter 4 Driver Installation Chapter 4 Driver Installation 4 - 1
EPIC Board EPIC-HD07 The EPIC-HD07 comes with a DVD-ROM that contains all drivers and utilities that meet your needs. Follow the sequence below to install the drivers: Step 1 – Install Chipset Driver Step 2 – Install Audio Driver Step 3 – Install LAN Driver Step 4 – Install AHCI Driver Step 5 – Install Touch Driver Please read instructions below for further detailed installations.
EPIC Board EPIC-HD07 4.1 Installation: Insert the EPIC-HD07 DVD-ROM into the DVD-ROM Drive. And install the drivers from Step 1 to Step 5 in order. Step 1 – Install Chipset Driver 1. Click on the STEP1-CHIPSET folder and select the OS folder your system is 2. Double click on the Setup.exe located in each OS folder 3. Follow the instructions that the window shows 4. The system will help you install the driver automatically Step 2 – Install Audio Driver 1.
EPIC Board EPIC-HD07 Step 4 – Install AHCI Driver Please refer to the Appendix D AHCI Setting Step 5 – Install Touch Driver 1. Click on the STEP5-TOUCH folder and double click on the Setup.exe 2. Follow the instructions that the window shows 3.
EPIC Board EPIC-HD07 Appendix A Programming the Watchdog Timer Appendix A Programming the Watchdog Timer A-1
EPIC Board EPIC-HD07 A.1 Programming EPIC-HD07 utilizes FINTEK 81866 chipset as its watchdog timer controller. Below are the procedures to complete its configuration and the AAEON initial watchdog timer program is also attached based on which you can develop customized program to fit your application. Configuring Sequence Description After the hardware reset or power-on reset, the FINTEK 81866 enters the normal mode with all logical devices disabled except KBC.
EPIC Board EPIC-HD07 There are three steps to complete the configuration setup: (1) Enter the MB PnP Mode; (2) Modify the data of configuration registers; (3) Exit the MB PnP Mode. Undesired result may occur if the MB PnP Mode is not exited normally. (1) Enter the MB PnP Mode To enter the MB PnP Mode, four special I/O write operations are to be performed during Wait for Key state.
EPIC Board EPIC-HD07 Watch Dog Timer 1, 2, 3 Control Register (Index=F5h,F6h,FAh Default=00h) Appendix A Programming the Watchdog Timer A-4
EPIC Board EPIC-HD07 A.
EPIC Board EPIC-HD07 Void aaeonWdtSetTimeoutCount(BYTE tTimeout){ f81866SetLdn(0x07); f81866WriteByte(F81866_WDT_TIME_REG, tTimeout); } Void aaeonWdtSetEnable(BOOL bEnable){ f81866SetLdn(0x07); if(bEnable){ f81866WriteByte(0x30, 0x01); WDT_BASE_ADDR = (f81866ReadByte(F81866_WDT_BASEADDR_REG_MSB) << 8) | f81866ReadByte(F81866_WDT_BASEADDR_REG_LSB); WDT_STATUS = f81866ReadByte(F81866_WDT_CONTROL_REG); f81866WriteByte(F81866_WDT_CONTROL_REG, WDT_STATUS | 0x20); WDT_STATUS = f81866ReadByte(F81866_WDT_PME_REG
EPIC Board EPIC-HD07 Void aaeonSuperIOClose(){ aaeonioWritePortByte(F81866_INDEX, 0xaa); } Appendix A Programming the Watchdog Timer A-7
EPIC Board EPIC-HD07 Appendix B I/O Information Appendix B I/O Information B-1
EPIC Board B.
EPIC Board EPIC-HD07 Appendix B I/O Information B-3
EPIC Board B.
EPIC Board EPIC-HD07 B.
EPIC Board Appendix B I/O Information B-6 EPIC-HD07
EPIC Board EPIC-HD07 B.
EPIC Board EPIC-HD07 Appendix C Mating Connector Appendix C Mating Connector C - 1
EPIC Board EPIC-HD07 C.1 List of Mating Connectors and Cables The table notes mating connectors and available cables.
EPIC Board EPIC-HD07 PANEL CN14 MINICARD CN15 mSATA DVI+VGA3 DVI/VGA LAN1/LAN2 LAN USB1/2 USB USB3/4/5/6 USB COM1 COM PORT COM3/4/ COM PORT FOXCONN AS0B226-S68K N/A -7 F FOXCONN AS0B226-S68K N/A -7 F ASTRON 1860044-006-R N/A N/A UDE N/A RT7-17FAAM1 N/A A TECHBEST KS-002D-ANB( N/A 2.
EPIC Board EPIC-HD07 Appendix D AHCI Setting Appendix D AHCI Setting D-1
EPIC Board EPIC-HD07 D.1 Setting AHCI OS installation to setup AHCI Mode. Step 1: Copy the files below from “Driver DVD -> STEP4AHCI\WinXP\SB8xx_RAID_XP_3.2.1540.
EPIC Board EPIC-HD07 Step 3: Setup OS Step 4: Press “F6” Appendix D AHCI Setting D-3
EPIC Board Step 5: Choose “S” Step 6: Choose “AMD (R) A55E Chipset” Appendix D AHCI Setting D-4 EPIC-HD07
EPIC Board EPIC-HD07 Step 7: It will show the model number you select and then press “ENTER Step 8: Setup is loading files Appendix D AHCI Setting D-5
EPIC Board EPIC-HD07 Appendix E Electrical Specifications for I/O Ports Appendix E Electrical Specifications for I/O Ports E-1
EPIC Board EPIC-HD07 E.1 Electrical Specifications for I/O Ports I/O Reference Signal Name LVDS Port 1 CN1 VCC LVDS Port 2 CN2 VCC LPC Port CN3 +3.3V +3.3V/0.5A CN4 VDD +5V/2A or +12V/2A CN5 VDD +5V/2A or +12V/2A CN6 +5V +5V/1A CN7 +5V +5V/0.
EPIC Board VGA / DVI Ports DVI+VGA EPIC-HD07 VGA: +5V DVI : +5V +5V/0.
