EPIC Board EPIC-QM77 EPIC-QM77 ® Intel Core™ i7/i5/i3/Celeron® Processor Supports DDR3/L 1333/1600 Memory 18/24-bit Single/Dual Channel LVDS CRT, DVI-I, HDMI 2 USB 3.0, 4 USB2.0, 6 COMs, 2 SATA 16-bit Digital I/O Co-lay with LPT EPIC-QM77 Manual 1st Ed. June.
EPIC Board EPIC-QM77 Copyright Notice This document is copyrighted, 2013. All rights are reserved. The original manufacturer reserves the right to make improvements to the products described in this manual at any time without notice. No part of this manual may be reproduced, copied, translated, or transmitted in any form or by any means without the prior written permission of the original manufacturer. Information provided in this manual is intended to be accurate and reliable.
EPIC Board EPIC-QM77 Acknowledgments All other products’ name or trademarks are properties of their respective owners. Award is a trademark of Award Software International, Inc. CompactFlash™ is a trademark of the Compact Flash Association. Intel®, Core™ i7/i5/i3/Celeron® are trademarks of Intel® Corporation. Microsoft Windows is a registered trademark of Microsoft Corp. ITE is a trademark of Integrated Technology Express, Inc.
EPIC Board EPIC-QM77 Packing List Before you begin installing your card, please make sure that the following materials have been shipped: Product DVD EPIC-QM77 1702150155 SATA Power Cable 1709070500 SATA Cable M10QM77000 Heat Spreader 9657666600 Jumper Cap If any of these items are missing or damaged, please contact your distributor or sales representative immediately.
EPIC Board EPIC-QM77 Contents Chapter 1 General Information 1.1 Introduction................................................................ 1-2 1.2 Features .................................................................... 1-3 1.3 Specifications ............................................................ 1-4 Chapter 2 Quick Installation Guide 2.1 Safety Precautions .................................................... 2-2 2.2 Location of Connectors and Jumpers ....................... 2-3 2.
EPIC Board EPIC-QM77 2.18 COM2 Slew Selection (JP12).................................. 2-16 2.19 VGA & DVI-I CONNECTOR (CN1) ......................... 2-16 2.20 Touch Screen Connector (CN2).............................. 2-18 2.21 SATA Power Connector (CN3) ............................... 2-19 2.22 SPI Flash Header (CN4) ......................................... 2-19 2.23 1st Backlight Connector (CN5)................................ 2-20 2.24 2nd Backlight Connector (CN6) ..............................
EPIC Board EPIC-QM77 2.43 USB2.0 Connector (USB5) ..................................... 2-38 2.44 USB2.0 Connector (USB6) ..................................... 2-39 2.45 RS-232 Serial Port Dual Connector (COM1) .......... 2-39 2.46 RS-232 Serial Port Connector (COM3)................... 2-40 2.47 RS-232 Serial Port Connector (COM4)................... 2-41 2.48 RS-232 Serial Port Connector (COM5)................... 2-42 2.49 RS-232 Serial Port Connector (COM6)................... 2-42 2.
EPIC Board EPIC-QM77 B.3 IRQ Mapping Chart ................................................B-6 B.4 DMA Channel Assignments.................................B-11 Appendix C Mating Connector C.1 List of Mating Connectors and Cables.................. C-2 Appendix D Electrical Specifications for I/O Ports D.1 Electrical Specifications for I/O Ports ................... D-2 D.2 DIO Programming................................................. D-3 D.3 Digital I/O Register..........................................
EPIC Board EPIC-QM77 Chapter 1 General Information Chapter 1 General Information 1- 1
EPIC Board EPIC-QM77 1.1 Introduction AAEON announces a brand new EPIC Board EPIC-QM77, designed to fit in diverse applications that demand for fitting in different space limitations and high performance. EPIC-QM77 accommodates onboard Intel® Core™ ® i7/i5/i3/Celeron Processor and features one socket for a 204-pin DDR3/L 1333/1600 SODIMM for up to 8GB of system memory. Moreover, EPIC-QM77 adopts Intel® QM77 chipset to achieve an excellent performance.
EPIC Board EPIC-QM77 1.2 Features Intel® Core™ i7/i5/i3/Celeron® Processor Intel® QM77/HM76 SODIMM DDR3/L 1333/1600MHz Memory, Max. 8GB Gigabit Ethernet x 2 Up To 24-bit Dual-channel LVDS LCD 2CH HD Audio SATA 6.0Gb/s x 2, mSATA (Full-Size) Slot x 1 USB 3.0 x 2, USB2.
EPIC Board EPIC-QM77 1.3 Specifications System Form Factor EPIC Express Board Processor Intel® Core™ i7/i5/i3/Celeron® Processor System Memory 204-pin SODIMM DDR3/L 1333/1600MHz Memory, Max.
EPIC Board EPIC-QM77 Board Size 4.5" x 6.5" (115mm x 165mm) Gross Weight 0.88 lb (0.
EPIC Board EPIC-QM77 supports 5/12V on D-Sub connector (COM 2) on rear I/O COM1 stack up on top of COM2; 4 COM ports on box head Parallel Port SPP/EPP/ECP Mode USB 4 USB 2.0 with box header, 2 USB3.
EPIC Board EPIC-QM77 Chapter 2 Quick Installation Guide Chapter 2 Quick Installation Guide 2-1
EPIC Board EPIC-QM77 2.1 Safety Precautions Always completely disconnect the power cord from your board whenever you are working on it. Do not make connections while the power is on, because a sudden rush of power can damage sensitive electronic components. Always ground yourself to remove any static charge before touching the board. Modern electronic devices are very sensitive to static electric charges. Use a grounding wrist strap at all times.
EPIC Board EPIC-QM77 2.
EPIC Board EPIC-QM77 Solder Side Solder Side Chapter 2 Quick Installation Guide 2-4
EPIC Board EPIC-QM77 2.
EPIC Board EPIC-QM77 Solder Side Solder Side Chapter 2 Quick Installation Guide 2-6
EPIC Board EPIC-QM77 2.4 List of Jumpers The board has a number of jumpers that allow you to configure your system to suit your application.
EPIC Board EPIC-QM77 2.5 List of Connectors The board has a number of connectors that allow you to configure your system to suit your application.
EPIC Board EPIC-QM77 LAN1 1000 Base-Tx Ethernet Connector LAN2 1000 Base-Tx Ethernet Connector USB1 Dual USB3.0 Connector USB3 USB2.0 Connector USB4 USB2.0 Connector USB5 USB2.0 Connector USB6 USB2.
EPIC Board EPIC-QM77 2.6 Setting Jumpers You configure your card to match the needs of your application by setting jumpers. A jumper is the simplest kind of electric switch. It consists of two metal pins and a small metal clip (often protected by a plastic cover) that slides over the pins to connect them. To “close” a jumper you connect the pins with the clip. To “open” a jumper you remove the clip. Sometimes a jumper will have three pins, labeled 1, 2 and 3.
EPIC Board EPIC-QM77 2.7 LPD_DIO Selection (JP1) LPT DIO JP1 Function Off LPT On DIO 2.8 AT/ATX Selection (JP2) ATX AT JP2 Function Off ATX On AT 2.9 Touch Screen Selection (JP3) 4,8 Wire 5 Wire JP3 Function Off 5 Wire On 4.
EPIC Board EPIC-QM77 2.10 Ring_12V_5V Selection (JP4) +12V RI2# +5V JP4 Function 1-2 +12V 3-4 RI2#_SEL 5-6 +5V 2.11 LCD VCC Selection (JP5) LVDS1 +5V LVDS1 +3.3V LVDS 1 LVDS 1 Function 1-3 +5V (Default) 3-5 +3.3V LVDS2 +5V Chapter 2 Quick Installation Guide 2-12 LVDS2 +3.
EPIC Board EPIC-QM77 LVDS 2 LVDS 2 Function 2-4 +5V (Default) 4-6 +3.3V 2.
EPIC Board EPIC-QM77 2.13 LCD Backlight Control Selection (JP7) 1 3 5 1 3 5 2 4 6 LVDS1 Voltage-mode 2 4 6 LVDS1 PWM-mode LVDS 1 LVDS 1 Function 1-3 Voltage-mode 3-5 PWM-mode 1 3 5 1 3 5 2 4 6 LVDS2 Voltage-mode LVDS2 PWM-mode LVDS 2 LVDS 2 Function 2-4 Voltage-mode 4-6 PWM-mode 2.
EPIC Board EPIC-QM77 2.15 Clear CMOS Selection (JP9) 1 2 3 1 2 3 NORMAL CLEAR CMOS JP9 Function 1-2 NORMAL 2-3 CLEAR CMOS 2.16 PCI-104 I/O Voltage Selection (JP10) +5V +3.3V JP10 Function 1-2 +5V 2-3 +3.3V 2.
EPIC Board EPIC-QM77 2.18 COM2 Slew Selection (JP12) 250k 1M/10M JP12 Function Off 250k On 1M/10M 2.
EPIC Board Pin Pin Name EPIC-QM77 Signal Type Signal Level I/O 2 GREEN 4 NC 6 GND GND 8 GND GND 10 CRT_PLUG# IN 12 DDC_DATA I/O 14 VSYNC I/O DVI Pin Pin Name Signal Type 1 DVI_DATA2_N I/O 3 GND GND 5 NC 7 DVI_SDA I/O 9 DVI_DATA1_N I/O 11 GND GND 13 NC 15 D_CRT_PLUG# IN 17 DVI_DATA0_N I/O 19 GND GND 21 NC 23 DVI_CLK_P I/O C1 RED I/O C3 BLUE I/O C5 GND GND Signal Level Chapter 2 Quick Installation Guide 2-17
EPIC Board Pin Pin Name EPIC-QM77 Signal Type 2 DVI_DATA2_P 4 NC 6 DVI_SCL I/O 8 VSYNC 10 DVI_DATA1_P I/O I/O 12 NC 14 V5S_DISP PWR 16 DVI_HPD I/O 18 DVI_DATA0_P I/O 20 NC 22 GND GND 24 DVI_CLK_N I/O C2 GREEN I/O C4 HSYNC I/O C6 GND GND Signal Level I/O 5V 2.
EPIC Board EPIC-QM77 4 X- IN 5 X+ IN 6 SENSE IN 7 Y+ IN 8 X- IN 9 X+ IN 2.21 SATA Power Connector (CN3) Pin Pin Name Signal Type Signal Level 1 V5S PWR +5V 2 GND GND GND Pin Name Signal Type Signal Level 1 V3.3M_SPI PWR +3.3V 3 SPI_CE#_F IN 5 SPI_SO_F OUT 2.
EPIC Board EPIC-QM77 Pin Pin Name Signal Type 2 GND GND 4 SPI_CLK_F I/O 6 SPI_SI_F IN Signal Level 8 2.23 1st Backlight Connector (CN5) Pin Pin Name Signal Type Signal Level 1 VCC_LVDS_BKLT1 PWR +5V OR +12V 2 L_BRIGHTNESS1 OUT 3 GND GND 4 GND GND 5 BKLT_EN1 OUT 2.
EPIC Board EPIC-QM77 3 GND GND 4 GND GND 5 BKLT_EN2 OUT 2.
EPIC Board EPIC-QM77 33 PETp0_TX+ I/O 35 GND GND 37 GND GND 39 +V3.3_MINICARD1 PWR +3.3V 41 +V3.3_MINICARD1 PWR +3.3V 43 NC 45 Reserved I/O 47 Reserved I/O 49 Reserved I/O 51 Reserved I/O Pin Pin Name Signal Type 2 V3.3_MINICARD1 PWR 4 GND GND 6 +V1.5S PWR 8 Reserved 10 Reserved 12 Reserved 14 Reserved 16 Reserved 18 Reserved 20 MINI_DISABLE# IN 22 BUF_PLT_RST# IN 24 +V3.3_MINICARD1 PWR 26 GND GND 28 +V1.
EPIC Board EPIC-QM77 32 SMB_DATA_SBY I/O 34 GND GND 36 USB_PN2 I/O 38 USB_PP2 I/O 40 GND GND 42 Reserved 44 Reserved 46 Reserved 48 +V1.5S PWR 50 GND GND 52 +V3.3_MINICARD1 PWR +1.5V +3.3V 2.
EPIC Board 17 Reserved 19 Reserved EPIC-QM77 21 GND GND 23 PCIE_RXN6 I/O 25 PCIE_RXP6 I/O 27 GND GND 29 GND GND 31 PCIE_TNX6 I/O 33 PCIE_TXP6 I/O 35 GND GND 37 GND GND 39 +V3.3_MINICARD2 PWR +3.3V 41 +V3.3_MINICARD2 PWR +3.3V 43 Reserved 45 Reserved 47 CL_CLK I/O 49 CL_DATA I/O 51 CL_RST# IN Pin Pin Name Signal Type 2 +V3.3_MINICARD2 PWR 4 GND GND 6 +V1.
EPIC Board EPIC-QM77 16 Reserved 18 Reserved 20 MINI_DISABLE# IN 22 BUF_PLT_RST# IN 24 +V3.3_MINICARD2 PWR 26 GND GND 28 +V1.5S PWR 30 SMB_CLK_SBY I/O 32 SMB_DATA_SBY I/O 34 GND GND 36 USB_PN7 I/O 38 USB_PP7 I/O 40 GND GND 42 Reserved 44 Reserved 46 Reserved 48 +V1.5S PWR 50 GND GND 52 +V3.3_MINICARD2 PWR +3.3V +1.5V +1.5V +3.3V 2.
EPIC Board EPIC-QM77 LPT Mode: Pin Pin Name Signal Type 1 STOBE# I/O 3 PPD0 I/O 5 PPD1 I/O 7 PPD2 I/O 9 PPD3 I/O 11 PPD4 I/O 13 PPD5 I/O 15 PPD6 I/O 17 PPD7 I/O 19 ACK# I/O 21 BUSY I/O 23 PE I/O 25 SLCT I/O Pin Pin Name Signal Type 2 #AFD I/O 4 ERR# I/O 6 PINIT# I/O 8 SLIN# 10 GND I/O GND 12 GND GND 14 GND GND 16 GND GND 18 GND GND Chapter 2 Quick Installation Guide 2-26 Signal Level Signal Level
EPIC Board EPIC-QM77 20 GND GND 22 GND GND 24 GND GND 26 N.C DIO Mode: Pin Pin Name Signal Type 1 GPIO7 I/O 3 GPIO8 I/O 5 GPIO9 I/O 7 GPIO10 I/O 9 GPIO11 I/O 11 GPIO12 I/O 13 GPIO13 I/O 15 GPIO14 I/O 17 GPIO15 I/O 19 GPIO2 I/O 21 GPIO1 I/O 23 GPIO0 I/O 25 N.
EPIC Board EPIC-QM77 12 GND GND 14 GND GND 16 GND GND 18 GND GND 20 GND GND 22 GND GND 24 GND GND 26 N.C 2.
EPIC Board EPIC-QM77 2.
EPIC Board EPIC-QM77 2.30 ATX 4Pin Power Connector (CN12) Pin Pin Name Signal Type 1 GND GND 3 +12VSB PWR 2 GND GND 4 +12VSB PWR Signal Level +12V +12V 2.31 Front Panel Connector(CN13) Pin Pin Name Signal Type 1 PWRSIN# IN 2 GND GND 3 +V5S PWR 4 FP_SPKR# IN 5 +V3.3S PWR 6 FP_HDLED# IN 7 +V3.3S PWR 8 GND GND 9 HWRST# IN 10 GND GND Chapter 2 Quick Installation Guide 2-30 Signal Level +5V +3.3V +3.
EPIC Board EPIC-QM77 2.32 AMP-R Channel Connector (CN14) Pin Pin Name Signal Type 1 SPK_R+ OUT 2 SPK_R- OUT Signal Level 2.33 2Pin Power Connector (CN15) Pin Pin Name Signal Type 1 +12VSB PWR 2 GND GND Signal Level +12V 2.
EPIC Board EPIC-QM77 Pin Pin Name Signal Type 1 LPC_AD0 I/O 2 LPC_AD1 I/O 3 LPC_AD2 I/O 4 LPC_AD3 I/O 5 +V3.3S PWR 6 LPC_FRAME# IN 7 BUF_PLT_RST# IN 8 GND GND 9 CLK_LPC_33M OUT 10 LPC_DRQ#0 OUT 11 LPC_DRQ#1 OUT 12 INT_SERIRQ I/O Signal Level +3.3V 2.35 AMP-L Channel Connector (CN17) Pin Pin Name Signal Type 1 SPK_L+ OUT 2 SPK_L- OUT 2.
EPIC Board EPIC-QM77 Pin Pin Name Signal Type Signal Level 1 UIM_PWR PWR +3.3V 2 UIM_DAT I/O 3 UIM_CLK OUT 4 UIM_RST OUT 5 UIM_VPP GND 2.
EPIC Board EPIC-QM77 29 LVDSB_CLK# I/O Pin Pin Name Signal Type 2 L_BRIGHTNESS1 OUT 4 GND GND 6 LVDSA_CLK OUT 8 GND GND 10 LVDSA_DATA0 12 LVDSA_DATA1 I/O 14 LVDSA_DATA2 I/O 16 LVDSA_DATA3 I/O 18 LVDS_DDC_CLK I/O 20 LVDSB_DATA0 I/O 22 LVDSB_DATA1 I/O 24 LVDS_DATA2 I/O 26 LVDSB_DATA3 I/O 28 GND GND 30 LVDSB_CLK I/O Signal Level I/O 2.
EPIC Board EPIC-QM77 3 +VDD_LVDS2 PWR 5 LVDSC_CLK# I/O 7 +VDD_LVDS2 PWR 9 LVDSC_DATA0# I/O 11 LVDSC_DATA1# I/O 13 LVDSC_DATA2# I/O 15 I/O 19 LVDSC_DATA3# LVDS_DDC_DATA_3 460 LVDSD_DATA0# 21 LVDSD_DATA1# I/O 23 LVDSD_DATA2# I/O 25 LVDSD_DATA3# I/O 27 +VDD_LVDS2 PWR 29 LVDSD_CLK# I/O 17 Pin Pin Name I/O +3.
EPIC Board EPIC-QM77 24 LVDSD_DATA2 I/O 26 LVDSD_DATA3 I/O 28 GND 30 LVDSD_CLK GND I/O 2.39 Fan Connector (FAN1) Pin Pin Name Signal Type 1 GND GND 2 FAN_CTL OUT 3 FAN_TAC OUT 4 FAN_CTL_R OUT Signal Level 2.40 USB3.
EPIC Board EPIC-QM77 11 USBD1- I/O 13 GND GND 15 USB3_RX1_CON_P I/O 17 USB3_TX1_CON_N I/O Pin Pin Name Signal Type 2 USBD0- I/O 4 GND GND 6 USB3_RX0_COP_P I/O 8 USB3_TX0_CON_N I/O 10 +V5A_USB_0 PWR 12 USBD1+ I/O 14 USB3_RX1_CON_N I/O 16 GND GND 18 USB3_TX1_CON_P I/O Signal Level +5V 2.41 USB2.
EPIC Board EPIC-QM77 2.42 USB2.0 Connector (USB4) Pin Pin Name Signal Type 1 +V5A_USB_2 PWR 2 USBD12- I/O 3 USBD12+ I/O 4 GND GND 5 GND GND Signal Level +5V 2.43 USB2.
EPIC Board EPIC-QM77 2.44 USB2.0 Connector (USB6) Pin Pin Name Signal Type 1 +V5A_USB_3 PWR 2 USBD13- I/O 3 USBD13+ I/O 4 GND GND 5 GND GND Signal Level +5V 2.
EPIC Board EPIC-QM77 11 RXD2(422RXD+) IN 13 DTR#2(422RXD-) OUT 15 DSR#2 IN 17 CTS#2 IN Pin Pin Name Signal Type RXD#1 IN 4 DTR#1 OUT 6 DSR#1 IN 8 CTS#1 IN DCD#2 (485D-)(422TXD-) IN 10 12 TXD2 (485D+)(422TXD+) OUT 14 GND OUT 16 RTS#2 OUT 18 RI#2 2 IN 2.
EPIC Board Pin Pin Name EPIC-QM77 Signal Type 1 DCD#3 IN 2 DSR#3 IN 3 RXD3 IN 4 RTS#3 OUT 5 TXD3 OUT 6 CTS#3 IN 7 DTR#3 OUT 8 RI#3 IN Signal Level 2.
EPIC Board EPIC-QM77 2.48 RS-232 Serial Port Connector (COM5) Pin Pin Name Signal Type 1 DCD#5 IN 2 DSR#5 IN 3 RXD5 IN 4 RTS#5 OUT 5 TXD5 OUT 6 CTS#5 IN 7 DTR#5 OUT 8 RI#5 IN 9 GND GND 2.
EPIC Board Pin Pin Name EPIC-QM77 Signal Type 1 DCD#6 IN 2 DSR#6 IN 3 RXD6 IN 4 RTS#6 OUT 5 TXD6 OUT 6 CTS#6 IN 7 DTR#6 OUT 8 RI#6 IN 9 GND GND Signal Level 2.50 Battery Connector (BAT1) Pin Pin Name Signal Type 1 RTCBAT PWR 2 GND GND Signal Level +3.3V 2.
EPIC Board Pin Pin Name EPIC-QM77 Signal Type 1 KBDATA OUT 2 KBCLK OUT 3 GND GND 4 +V5A_KBMS PWR 5 MSDATA OUT 6 MSCLK OUT Signal Level +5V 2.52 LAN Ethernet RJ-45 Connector (LAN1) ACT/LINK LED 8 Pin SPEED LED 1 Pin Name Signal Type 1 LAN1_MDIP0 I/O 2 LAN1_MDIN0 I/O 3 LAN1_MDIP1 I/O 4 LAN1_MDIN1 I/O 5 LAN1_MDIP2 I/O 6 LAN1_MDIN2 I/O 7 LAN1_MDIP3 I/O 8 LAN1_MDIN3 I/O 2.
EPIC Board Pin Pin Name EPIC-QM77 Signal Type 1 LAN2_MDIP0 I/O 2 LAN2_MDIN0 I/O 3 LAN2_MDIP1 I/O 4 LAN2_MDIN1 I/O 5 LAN2_MDIP2 I/O 6 LAN2_MDIN2 I/O 7 LAN2_MDIP3 I/O 8 LAN2_MDIN3 DIFF. 8 LAN1_MDIN3 I/O Signal Level 2.
EPIC Board EPIC-QM77 2.
EPIC Board EPIC-QM77 Below Table for China RoHS Requirements 产品中有毒有害物质或元素名称及含量 AAEON Main Board/ Daughter Board/ Backplane 有毒有害物质或元素 部件名称 铅 汞 镉 六价铬 多溴联苯 多溴二苯醚 (Pb) (Hg) (Cd) (Cr(VI)) (PBB) (PBDE) × ○ ○ ○ ○ ○ × ○ ○ ○ ○ ○ 印刷电路板 及其电子组件 外部信号 连接器及线材 O：表示该有毒有害物质在该部件所有均质材料中的含量均在 SJ/T 11363-2006 标准规定的限量要求以下。 X：表示该有毒有害物质至少在该部件的某一均质材料中的含量超出 SJ/T 11363-2006 标准规定的限量要求。 备注：此产品所标示之环保使用期限，系指在一般正常使用状况下。 Chapter 2 Quick Installation Guide 2-47
Industrial Motherboard EPIC-QM77 Chapter 3 AMI BIOS Setup Chapter 3 AMI BIOS Setup 3-1
Industrial Motherboard EPIC-QM77 3.1 System Test and Iinitialization These routines test and initialize board hardware. If the routines encounter an error during the tests, you will either hear a few short beeps or see an error message on the screen. There are two kinds of errors: fatal and non-fatal. The system can usually continue the boot up sequence with non-fatal errors. System configuration verification These routines check the current system configuration stored in the CMOS memory and BIOS NVRAM.
Industrial Motherboard EPIC-QM77 3.2 AMI BIOS Setup AMI BIOS ROM has a built-in Setup program that allows users to modify the basic system configuration. This type of information is stored in battery-backed CMOS RAM and BIOS NVRAM so that it retains the Setup information when the power is turned off. Entering Setup Power on the computer and press or immediately. This will allow you to enter Setup. Main Set the date, use tab to switch between date elements.
Industrial Motherboard Setup Menu Setup submenu: Main Chapter 3 AMI BIOS Setup 3-4 EPIC-QM77
Industrial Motherboard EPIC-QM77 Setup submenu: Advanced Options summary: ICC Spread Disabled Optimal Default, Failsafe Default Spectrum Enabled Enable Spread Spectrum function for BCLK, DMI, PEG, PCIe, PCI33, SATA, USB3.
Industrial Motherboard EPIC-QM77 ACPI Settings Options summary: Suspend mode S1 only (CPU Stop Clock) S3 only (Suspend to RAM) Select the ACPI state used for System Suspend Chapter 3 AMI BIOS Setup 3-6 Optimal Default, Failsafe Default
Industrial Motherboard EPIC-QM77 Trusted Computing Options summary: Security Device Support Disable Optimal Default, Failsafe Default Enable Enable or Disables BIOS support for security device. O.S. will not show Security Device. TCG EFI protocol and INT1A interface will not be available.
Industrial Motherboard EPIC-QM77 CPU Configuration Options summary: Hyper-Threading Disabled Enabled Optimal Default, Failsafe Default En/Disable CPU Hyper-Threading function Intel Virtualization Disabled Optimal Default, Failsafe Default Technology Enabled When enabled, a VMM can utilize the additional hardware capabilities provided by Vanderpool Technology Chapter 3 AMI BIOS Setup 3-8
Industrial Motherboard EPIC-QM77 Digital IO Options summary: DIO_P#1~4 Input Default Output Allows BIOS to select input/output function to corresponding DIO ping. DIO_P#5~8 Input Output Default Allows BIOS to select input/output function to corresponding DIO ping. DIO_P#5~8 Direction Low Hi Default Allows BIOS to select high/low voltage level to output to corresponding DIO ping. DIO_P#11~14 Input Default Output Allows BIOS to select input/output function to corresponding DIO ping.
Industrial Motherboard IDE Configuration (IDE) Chapter 3 AMI BIOS Setup 3-10 EPIC-QM77
Industrial Motherboard EPIC-QM77 IDE Configuration (AHCI) Chapter 3 AMI BIOS Setup 3-11
Industrial Motherboard EPIC-QM77 IDE Configuration (RAID) Options summary: SATA Controllers Disabled Enabled Default En/Disable SATA Controller. SATA Mode IDE Default AHCI RAID IDE: Configure SATA controllers as legacy IDEAHCI: Configure SATA controllers to operate in AHCI mode SATA Controller Speed Gen1 Gen2 Gen3 Default Indicates the maximum speed the SATA controller can support. Port x Disabled Enabled Optimal Default, Failsafe Default En/Disable SATA Port.
Industrial Motherboard EPIC-QM77 AMT Configuration Options summary: Intel AMT Disabled Enabled Optimal Default, Failsafe Default En/Disable Intel Active Management Technology BIOS Extension. Note: iAMT H/W is always enabled. This option just controls the BIOS extension execution. If enabled, this requires additional firmware in the SPI device. Un-configure ME Disabled Optimal Default, Failsafe Default Enabled OEMFlag Bit 15: Un-Configure ME without password.
Industrial Motherboard EPIC-QM77 USB Configuration Options summary: Legacy USB Support Enabled Optimal Default, Failsafe Default Disabled Auto Enables BIOS Support for Legacy USB Support. When enabled, USB can be functional in legacy environment like DOS. AUTO option disables legacy support if no USB devices are connected Device Name (Emulation Auto Optimal Default, Failsafe Default Type) Floppy Forced FDD Hard Disk CDROM If Auto.
Industrial Motherboard EPIC-QM77 F81866 Super IO Configuration Chapter 3 AMI BIOS Setup 3-15
Industrial Motherboard EPIC-QM77 Serial Port 1 Configuration Options summary: Serial Port Disabled Enabled Allows BIOS to En/Disable correspond serial port. Change Settings Auto IO=3F8h; IRQ=4; IO=3F8h; IRQ=3,4; IO=2F8h; IRQ=3,4; IO=3E8h; IRQ=3.4 IO=2E8h; IRQ=3,4; Allows BIOS to Select Serial Port resource.
Industrial Motherboard EPIC-QM77 Serial Port 2 Configuration Options summary: Serial Port Disabled Enabled Allows BIOS to En/Disable correspond serial port. Device Mode RS232 RS422 RS485 Select working model. Change Settings Auto IO=2F8h; IRQ=3; IO=3F8h; IRQ=3,4; IO=2F8h; IRQ=3,4; IO=3E8h; IRQ=3,4; IO=2E8h; IRQ=3,4; Allows BIOS to Select Serial Port resource.
Industrial Motherboard EPIC-QM77 Serial Port 3 Configuration Options summary: Serial Port Disabled Enabled Allows BIOS to En/Disable correspond serial port. Change Settings Auto IO=3E8h; IRQ=10; IO=3E8h; IRQ=10,11;; IO=2E8h; IRQ=10,11; IO=2D0h; IRQ=10,11; IO=2D8h; IRQ=10,11; Allows BIOS to Select Serial Port resource.
Industrial Motherboard EPIC-QM77 Serial Port 4 Configuration Options summary: Serial Port Disabled Enabled Allows BIOS to En/Disable correspond serial port. Change Settings Auto IO=2E8h; IRQ=10; IO=3E8h; IRQ=10,11;; IO=2E8h; IRQ=10,11; IO=2D0h; IRQ=10,11; IO=2D8h; IRQ=10,11; Allows BIOS to Select Serial Port resource.
Industrial Motherboard EPIC-QM77 Serial Port 5 Configuration Options summary: Serial Port Disabled Enabled Allows BIOS to En/Disable correspond serial port. Device Mode RS232 RS422 RS485 Select working model. Change Settings Auto IO=2D0h; IRQ=10; IO=3E8h; IRQ=10,11;; IO=2E8h; IRQ=10,11; IO=2D0h; IRQ=10,11; IO=2D8h; IRQ=10,11; Allows BIOS to Select Serial Port resource.
Industrial Motherboard EPIC-QM77 Serial Port 6 Configuration Options summary: Serial Port Disabled Enabled Allows BIOS to En/Disable correspond serial port. Device Mode RS232 RS422 RS485 Select working model. Change Settings Auto IO=2D8h; IRQ=10; IO=3E8h; IRQ=10,11;; IO=2E8h; IRQ=10,11; IO=2D0h; IRQ=10,11; IO=2D8h; IRQ=10,11; Allows BIOS to Select Serial Port resource.
Industrial Motherboard EPIC-QM77 Parallel Port Configuration Options summary: Parallel Port Disabled Enabled Allows BIOS to En/Disable Parallel port. Change Settings Auto (Parallel Port) IO=378h; IRQ=5; IO=378h; IRQ=5,7; IO=278h; IRQ=5,7; IO=3BCh; IRQ=5,7; Allows BIOS to Select Serial Port resource. Device Mode STD Printer Mode SPP Mode EPP-1.9 and SPP Mode EPP-1.9 and SPP Mode ECP Mode ECP and EPP 1.9 Mode ECP and EPP 1.7 Mode Change the Printer Port mode.
Industrial Motherboard EPIC-QM77 F81866 H/W Monitor Options summary: Smart Fan Function Disabled Enabled Enable or Disable Smart Fan.
Industrial Motherboard EPIC-QM77 Smart Fan Mode Configuration (Auto Duty-Cycle Mode) Chapter 3 AMI BIOS Setup 3-24
Industrial Motherboard EPIC-QM77 Smart Fan Mode Configuration (Manual Duty Mode) Chapter 3 AMI BIOS Setup 3-25
Industrial Motherboard EPIC-QM77 Smart Fan Mode Configuration (Manual RPM Mode) Options summary: Manual Duty Mode Auto RPM Mode Auto Duty-Cycle Mode Default Fan 1 Smart Fan Control Smart Fan Mode Select Temperature 1 60 Default Temperature 2 50 Default Temperature 3 40 Default Temperature 4 30 Default Duty Cycle 1 85 Default Duty Cycle 2 70 Default Duty Cycle 3 60 Default Duty Cycle 4 50 Default Auto fan speed control. Fan speed will follow different temperature by different duty cycle 1-100.
Industrial Motherboard EPIC-QM77 Setup submenu: Chipset Chapter 3 AMI BIOS Setup 3-27
Industrial Motherboard EPIC-QM77 PCH-IO Configuration Options summary: Mini Card2 Controller Disabled Enabled Control the PCI Express Root Port. PCIe Speed Auto Gen1 Gen2 Select PCI Express port speed. Mini Card1 Controller Disabled Enabled Control the PCI Express Root Port. PCIe Speed Auto Gen1 Gen2 Select PCI Express port speed. PCH LAN Controller Disabled Enabled Control the PCI Express Root Port.
Industrial Motherboard EPIC-QM77 Enabled Default Control the PCI Express Root Port Azalia Disabled Enabled Auto Default Control Detection of the Azalia device. Disabled = Azalia will be unconditionally disabled; Enabled = Azalia will be unconditionally enabled; Auto = Azalia will be enabled if present, disabled otherwise. Azalia Internal HDMI Disabled Codec Enabled Default Enable or disable internal HDMI codec for Azalia. Power Mode ATX Type Default AT Type Select power supply mode.
Industrial Motherboard EPIC-QM77 System Agent (SA) Configuration Options summary: VT-d Disabled Enabled Check to enable VT-d function on MCH Chapter 3 AMI BIOS Setup 3-30 Default
Industrial Motherboard EPIC-QM77 Graphics Configuration Options summary: Primary Display Auto Default IGFX PEG PCI Select which of IGFX/PEG/PCI Graphics device should be Primary Display or select SG for Switchable Gfx. Internal Graphics Auto Default Disabled Enabled Keep IGD enabled based on setup options.
Industrial Motherboard DVMT Pre-Allocated EPIC-QM77 32MB 64MB Default 96MB 128MB 160MB 192MB 224MB 256MB 288MB 320MB 352MB 384MB 416MB 448MB 480MB 512MB 1024MB Select DVMT 5.0 Pre-Allocated (Fixed) Graphics Memory size used by the Internal Graphics Device. DVMT Total Gfx Mem 128MB 256MB Default MAX Select DVMT5.0 Total Graphic Memory size used by the Internal Graphics Device.
Industrial Motherboard EPIC-QM77 LCD Control Options summary: Primary Display VBIOS Default Default CRT DVI LVDS HDMI Select the Video Device which will be activated during POST. This has no effect if external graphics present. Secondary boot display selection will appear base on your selection. VGA modes will be supported only on primary display. Active LFP No LVDS Internal –LVDS Default External -LVDS Select the active LFP Configuration. No LVDS: VBIOS does not enable LVDS.
Industrial Motherboard Internal-LVDS LCD Panel Type EPIC-QM77 640x 480 18Bit 800x 480 18Bit 800x 600 18Bit 1024x 768 18Bit Default 1024x 768 24Bit 1280x 768 24Bit 1280x102414Bit Select LCD panel used by Internal Graphics Device by selecting the appropriate setup item. External-LVDS LCD Panel Type 1600x1200 48Bit (Ext. Only) Default 1920x1080 48Bit (Ext. Only) 1920x1200 48Bit (Ext. Only) Select LCD panel used by Internal Graphics Device by selecting the appropriate setup item.
Industrial Motherboard EPIC-QM77 Memory Information Chapter 3 AMI BIOS Setup 3-35
Industrial Motherboard EPIC-QM77 Setup submenu: Boot Options summary: Quiet Boot Disabled Enabled Default En/Disable showing boot logo. Launch I82579LM PXE Disabled Default OpROM Enabled En/Disable Legacy Boot Option for I82579LM. Launch I82583V PXE Disabled Default OpROM Enabled En/Disable Legacy Boot Option for I82583V.
Industrial Motherboard EPIC-QM77 BBS Priorities Chapter 3 AMI BIOS Setup 3-37
Industrial Motherboard EPIC-QM77 Security Change User/Supervisor Password You can install a Supervisor password, and if you install a supervisor password, you can then install a user password. A user password does not provide access to many of the features in the Setup utility. If you highlight these items and press Enter, a dialog box appears which lets you enter a password. You can enter no more than six letters or numbers. Press Enter after you have typed in the password.
Industrial Motherboard EPIC-QM77 Setup submenu: Exit Chapter 3 AMI BIOS Setup 3-39
EPIC Board EPIC-QM77 Chapter 4 Driver Installation Chapter 4 Driver Installation 4 - 1
EPIC Board EPIC-QM77 The EPIC-QM77 comes with a DVD-ROM that contains all drivers and utilities that meet your needs. Follow the sequence below to install the drivers: Step 1 – Install Chipset Driver Step 2 – Install VGA Driver Step 3 – Install LAN (Intel_82579) Driver Step 4 – Install Audio Driver Step 5 – Install ME Driver Step 6 – Install RAID & AHCI Driver Step 7 – Install TPM Driver Step 8 – Install Touch Driver Step 9 – Install USB3.
EPIC Board EPIC-QM77 4.1 Installation: Insert the EPIC-QM77 DVD-ROM into the DVD-ROM Drive. And install the drivers from Step 1 to Step 9 in order. Step 1 – Install Chipset Driver 1. Click on the Step1 - CHIPSET folder and then double click on the infinst_autol.exe 2. Follow the instructions that the window shows 3. The system will help you install the driver automatically Step 2 – Install VGA Driver 1. Click on the STEP2-VGA folder and select the OS folder your system is 2. Double click on the Setup.
EPIC Board EPIC-QM77 Step 3 – Install LAN (Intel_82579) Driver 1. Click on the STEP3-LAN (Intel_82579) folder and select the OS folder your system is 2. Double click on the .exe file located in each OS folder 3. Follow the instructions that the window shows 4. The system will help you install the driver automatically Step 4 – Install Audio Driver 1. Click on the STEP4-AUDIO folder and select the OS folder your system is 2. Double click on the Setup.exe file located in each OS folder 3.
EPIC Board EPIC-QM77 Step 7 – Install TPM Driver 1. Click on the STEP7-TPM folder and select the OS folder your system is 2. Double click on the Setup.exe file located in each OS folder 3. Follow the instructions that the window shows 4. The system will help you install the driver automatically Step 8 –Install Touch Driver 1. Click on the STEP8-TOUCH folder and select the appropriate version folder 2. Double click on the Setup.exe file located in each version folder 3.
EPIC Board EPIC-QM77 Appendix A Programming the Watchdog Timer Appendix A Programming the Watchdog Timer A-1
EPIC Board EPIC-QM77 A.1 Watchdog Timer Initial Program Table 1 : SuperIO relative register table Default Value Index 0x2E(Note1) Data 0x2F(Note2) Note SIO MB PnP Mode Index Register 0x2E or 0x4E SIO MB PnP Mode Data Register 0x2F or 0x4F Table 2 : Watchdog relative register table LDN Register BitNum Value Note Time of watchdog timer Timer Counter 0x07(Note3) 0xF6(Note4) (Note24) (0~255) This register is byte access Select time unit.
EPIC Board EPIC-QM77 ************************************************************************************ // SuperIO relative definition (Please reference to Table 1) #define byte SIOIndex #define byte SIOData //This parameter is represented from Note1 //This parameter is represented from Note2 #define void IOWriteByte(byte IOPort, byte Value); #define byte IOReadByte(byte IOPort); // Watch Dog relative definition (Please reference to Table 2) #define byte TimerLDN //This parameter is represe
EPIC Board EPIC-QM77 ************************************************************************************ VOID Main(){ // Procedure : AaeonWDTConfig // (byte)Timer : Time of WDT timer.(0x00~0xFF) // (boolean)Unit : Select time unit(0: second, 1: minute). AaeonWDTConfig(); // Procedure : AaeonWDTEnable // This procudure will enable the WDT counting.
EPIC Board EPIC-QM77 ************************************************************************************ // Procedure : AaeonWDTEnable VOID AaeonWDTEnable (){ WDTEnableDisable(EnableLDN, EnableReg, EnableBit, 1); } // Procedure : AaeonWDTConfig VOID AaeonWDTConfig (){ // Disable WDT counting WDTEnableDisable(EnableLDN, EnableReg, EnableBit, 0); // Clear Watchdog Timeout Status WDTClearTimeoutStatus(); // WDT relative parameter setting WDTParameterSetting(); } VOID WDTEnableDisable(byte LDN, byte Reg
EPIC Board EPIC-QM77 ************************************************************************************ VOID SIOEnterMBPnPMode(){ IOWriteByte(SIOIndex, 0x87); IOWriteByte(SIOIndex, 0x87); } VOID SIOExitMBPnPMode(){ IOWriteByte(SIOIndex, 0xAA); } VOID SIOSelectLDN(byte LDN){ IOWriteByte(SIOIndex, 0x07); // SIO LDN Register Offset = 0x07 IOWriteByte(SIOData, LDN); } VOID SIOBitSet(byte LDN, byte Register, byte BitNum, byte Value){ Byte TmpValue; SIOEnterMBPnPMode(); SIOSelectLDN(byte LDN); IOWriteB
EPIC Board EPIC-QM77 Appendix B I/O Information Appendix B I/O Information B-1
EPIC Board B.
EPIC Board EPIC-QM77 Appendix B I/O Information B-3
EPIC Board Appendix B I/O Information B-4 EPIC-QM77
EPIC Board EPIC-QM77 B.
EPIC Board B.
EPIC Board EPIC-QM77 .
EPIC Board Appendix B I/O Information B-8 EPIC-QM77
EPIC Board EPIC-QM77 Appendix B I/O Information B-9
EPIC Board Appendix B I/O Information B-10 EPIC-QM77
EPIC Board EPIC-QM77 B.
EPIC Board EPIC-QM77 Appendix C Mating Connector Appendix C Mating Connector C - 1
EPIC Board EPIC-QM77 C.1 List of Mating Connectors and Cables The table notes mating connectors and available cables. Connector Function Label CN2 CN3 CN5 CN6 CN9 CN10 CN13 CN14 CN16 CN17 CN18 USB3 Touch Screen Connector SATA Power Connector 1st Backlight Connector 2nd Backlight Connector LPT_DIO Connector Audio Connector Front Panel Connector Amp R-channel Connector LPC Connector Amp L-channel Connector 3G SIM Connector USB2.
EPIC Board USB4 USB5 USB6 COM3 COM4 COM5 COM6 KB1 FAN1 BAT1 LVDS1 LVDS2 USB2.0 Connector USB2.0 Connector USB2.
EPIC Board EPIC-QM77 Appendix D Electrical Specifications for I/O Ports Appendix D Electrical Specifications for I/O Ports D-1
EPIC Board EPIC-QM77 D.1 Electrical Specifications for I/O Ports I/O Reference Signal Name LVDS Port 1 LVDS1 VCC LVDS Port 2 LVDS2 VCC LPC Port LVDS Port 1 Inverter / Backlight Connector LVDS Port 2 Inverter / Backlight Connector +5V Output for SATA HDD CN16 +3.3V CN5 VDD +5V/2A or +12V/2A CN6 VDD +5V/2A or +12V/2A CN3 +5V +5V/1A Audio I/O Port CN10 +5V +5V/0.5A CN15 +12V +12V/3A CN12 +12V +12V/6A FAN FAN1 +5V +5V/0.5A Mini Card Slot CN8 mSATA Slot CN7 +3.3VSB +1.
EPIC Board EPIC-QM77 D.2 DIO Programming EPIC-QM77 utilizes FINTEK 81866 chipset as its Digital I/O controller. Below are the procedures to complete its configuration and the AAEON initial watchdog timer program is also attached based on which you can develop customized program to fit your application. There are three steps to complete the configuration setup: (1) Enter the MB PnP Mode; (2) Modify the data of configuration registers; (3) Exit the MB PnP Mode.
EPIC Board EPIC-QM77 D.
EPIC Board EPIC-QM77 Table 3 : Digital Output relative register table LDN Register BitNum Value Note DIO‐1 Output Data 0x06(Note27) 0x88(Note28) 0(Note29) (Note30) PE DIO‐2 Output Data 0x06(Note31) 0x88(Note32) 1(Note33) (Note34) BUSY DIO‐3 Output Data 0x06(Note35) 0x88(Note36) 2(Note37) (Note38) ACK# DIO‐4 Output Data 0x06(Note39) 0x88(Note40) 3(Note41) (Note42) SLIN# DIO‐5 Output Data 0x06(Note43) 0x88(Note44) 4(Note45) (Note46) PINIT# DIO‐6 Output Data 0x06(Note47)
EPIC Board EPIC-QM77 D.
EPIC Board EPIC-QM77 ************************************************************************************ // Digital Output control relative definition (Please reference to Table 3) #define byte DOutput1LDN // This parameter is represented from Note27 #define byte DOutput1Reg // This parameter is represented from Note28 #define byte DOutput1Bit // This parameter is represented from Note29 #define byte DOutput1Val // This parameter is represented from Note30 #define byte DOutput2LDN // This p
EPIC Board EPIC-QM77 ************************************************************************************ // Digital Input Status relative definition (Please reference to Table 2) #define byte DInput11LDN // This parameter is represented from Note3‐1 #define byte DInput11Reg // This parameter is represented from Note4‐1 #define byte DInput11Bit #define byte DInput12LDN // This parameter is represented from Note6‐1 #define byte DInput12Reg // This parameter is represented from Note7‐1 #define
EPIC Board EPIC-QM77 ************************************************************************************ // Digital Output control relative definition (Please reference to Table 3) #define byte DOutput11LDN // This parameter is represented from Note27‐1 #define byte DOutput11Reg // This parameter is represented from Note28‐1 #define byte DOutput11Bit // This parameter is represented from Note29‐1 #define byte DOutput11Val // This parameter is represented from Note30‐1 #define byte DOutput12L
EPIC Board EPIC-QM77 ************************************************************************************ VOID Main(){ Boolean PinStatus ; // Procedure : AaeonReadPinStatus // Input : // Example, Read Digital I/O Pin 3 status // Output : // InputStatus : // 0: Digital I/O Pin level is low // 1: Digital I/O Pin level is High PinStatus = AaeonReadPinStatus(DInput3LDN, DInput3Reg, DInput3Bit); // Procedure : AaeonSetOutputLevel // Input : // Example, Set Digital I/O Pin 6 level AaeonSetOutputLevel
EPIC Board EPIC-QM77 ************************************************************************************ Boolean AaeonReadPinStatus(byte LDN, byte Register, byte BitNum){ Boolean PinStatus ; PinStatus = SIOBitRead(LDN, Register, BitNum); Return PinStatus ; } VOID AaeonSetOutputLevel(byte LDN, byte Register, byte BitNum, byte Value){ ConfigToOutputMode(LDN, Register, BitNum); SIOBitSet(LDN, Register, BitNum, Value); } ************************************************************************************
EPIC Board EPIC-QM77 ************************************************************************************ VOID SIOEnterMBPnPMode(){ IOWriteByte(SIOIndex, 0x87); IOWriteByte(SIOIndex, 0x87); } VOID SIOExitMBPnPMode(){ IOWriteByte(SIOIndex, 0xAA); } VOID SIOSelectLDN(byte LDN){ IOWriteByte(SIOIndex, 0x07); // SIO LDN Register Offset = 0x07 IOWriteByte(SIOData, LDN); } VOID SIOBitSet(byte LDN, byte Register, byte BitNum, byte Value){ Byte TmpValue; SIOEnterMBPnPMode(); SIOSelectLDN(byte LDN); IOWriteB
EPIC Board EPIC-QM77 ************************************************************************************ Boolean SIOBitRead(byte LDN, byte Register, byte BitNum){ Byte TmpValue; SIOEnterMBPnPMode(); SIOSelectLDN(LDN); IOWriteByte(SIOIndex, Register); TmpValue = IOReadByte(SIOData); TmpValue &= (1 << BitNum); SIOExitMBPnPMode(); If(TmpValue == 0) Return 0; Return 1; } VOID ConfigToOutputMode(byte LDN, byte Register, byte BitNum){ Byte TmpValue, OutputEnableReg; OutputEnableReg = Register‐1; SIOEnterMBP
