LCD Display FOX-12D FOX-12D 12.1" Heavy-Duty Touch Display IP67 and IEC 60945 ed.
LCD Display FOX-12D Copyright Notice This document is copyrighted, 2012. All rights are reserved. The original manufacturer reserves the right to make improvements to the products described in this manual at any time without notice. No part of this manual may be reproduced, copied, translated, or transmitted in any form or by any means without the prior written permission of the original manufacturer. Information provided in this manual is intended to be accurate and reliable.
LCD Display FOX-12D Acknowledgments Intel® is registered trademarks of Intel® Corporation. IBM, PC/AT, PS/2 are trademarks of International Business Machines Corporation. Microsoft® Windows is a registered trademark of Microsoft® Corporation. RTL is a trademark of Realtek Semi-Conductor Co., Ltd. C&T is a trademark of Chips and Technologies, Inc. UMC is a trademark of United Microelectronics Corporation. ITE is a trademark of Integrated Technology Express, Inc.
LCD Display FOX-12D Packing List The LCD monitor comes with the following standard parts shown as below. Check and make sure they are included and in good condition. If anything is missing or damaged, contact the dealer immediately.
LCD Display FOX-12D Safety & Warranty 1. Read these safety instructions carefully. 2. Keep this user's manual for later reference. 3. Disconnect this equipment from any DC outlet before cleaning. Do not use liquid or spray detergents for cleaning. Use a damp cloth. 4. For pluggable equipment, the power outlet must be installed near the equipment and must be easily accessible. 5. Put this equipment on a reliable surface during installation. Dropping it or letting it fall could cause damage. 6.
LCD Display FOX-12D 12. If any of the following situations arises, get the equipment checked by service personnel: a. The power cord or plug is damaged. b. Liquid has penetrated into the equipment. c. The equipment has been exposed to moisture. d. The equipment does not work well, or you cannot get it to work according to the users manual. e. The equipment has been dropped and damaged. f. The equipment has obvious signs of breakage. 13.
LCD Display FOX-12D Below Table for China RoHS Requirements 产品中有毒有害物质或元素名称及含量 AAEON Display 有毒有害物质或元素 部件名称 铅 汞 镉 六价铬 多溴联苯 多溴二苯醚 (Pb) (Hg) (Cd) (Cr(VI)) (PBB) (PBDE) × ○ ○ ○ ○ ○ × ○ ○ ○ ○ ○ 外壳 × ○ ○ ○ ○ ○ 液晶模块 × ○ ○ ○ ○ ○ 触控模块 × ○ ○ ○ ○ ○ 电源 × ○ ○ ○ ○ ○ 印刷电路板 及其电子组件 外部信号 连接器及线材 O：表示该有毒有害物质在该部件所有均质材料中的含量均在 SJ/T 11363-2006 标准规定的限量要求以下。 X：表示该有毒有害物质至少在该部件的某一均质材料中的含量超出 SJ/T 11363-2006 标准规定的限量要求。 备注： 一、此产品所标示之环保使用期限，系指在一般正常使用状况下。 二、上述部件物质触控模块为选购品。 vi
LCD Display FOX-12D Contents Chapter 1 General Information 1.1 Introduction................................................................ 1-2 1.2 Features .................................................................... 1-3 1.3 General Specification ................................................ 1-4 1.4 Dimension ................................................................. 1-6 Chapter 2 Hardware Installation 2.1 Before Unpacking...................................................... 2-2 2.
LCD Display FOX-12D 3.8 Language- Submenu................................................. 3-9 3.9 Auto Config- Submenu.............................................. 3-10 3.10 Mode Resolution- Submenu.................................... 3-11 3.11 Exit Menu- Submenu............................................... 3-12 Chapter 4 Touch Screen Driver Installation 4.1 Introduction................................................................ 4-2 4.2 Resistive Touchscreen Control Board.......................
LCD Display FOX-12D Chapter 1 General Information Chapter 1 General Information 1-1
LCD Display FOX-12D 1.1 Introduction Thank you for purchasing of the Industry Touch Display with IP67 and IEC 60945 ed.4 compliant - a marvelous contribution of cutting edge technology. The LCD monitor has been designed with serious thoughts to present the best performance for most applications. Symbol of elegance, its compact and slim profile is well suited in working locations where space is at a premium.
LCD Display FOX-12D 1.2 Features IP67 Waterproof & Marine IEC 60945 ed.4 Compliant 12.1” 500 Nits XGA LED Backlight (FOX-12DHTT) 12.
LCD Display FOX-12D 1.3 General Specification System Input Signal VGA Control 4 Quick Keys on the front bezel I/O Connector VGA x 1 OS Support Windows® XP, Windows® 7, Linux Fedora Mechanical Construction IP67 Sealed Aluminum Alloy Chassis Mounting VESA 75/100 Dimension 13.58’’ x 11.1’’ x 2.36’’ (345mm x 282mm x 60mm ) Carton 20.24’’ x 9.72’’ x 20.71’’ (514mm x 247mm x Dimension 526mm ) Gross Weight 12.1 lb (5.5 Kg) Net Weight 8.36 lb (3.
LCD Display FOX-12D Humidity Vibration 1 g rms/ 5~500Hz/ Random operation Shock 15 G peak acceleration (11 msec. Duration) EMC CE/FCC Class A, IEC 60945 ed.4 Power Supply DC Input DC 9-30V Display type 12.1" TFT-LCD Max Resolution 1024 x 768 Display Modes Full screen in 1024x768, 800x600, 640x480, LCD 640x400 modes Max. Colors 16.
LCD Display FOX-12D 60.7 1.4 Dimension 345.0 282.
LCD Display FOX-12D Chapter 2 Hardware Installation Chapter 2 Hardware Installation 2-1
LCD Display FOX-12D 2.1 Before Unpacking It is very important to place the LCD Display in a suitable environment. The surface for placing the LCD Display should be stable and level. Make sure the place has good ventilation, and out of direct sunlight; away form sources of excessive dust, dirt, heat, water, moisture and vibration.
LCD Display FOX-12D 2.2 Checking The Accessories Please open the accessory box. You will find one VGA cable, one RS-232 cable and one power connector. All of three cables comes with M12-type connectors.
LCD Display FOX-12D 2.3 Connecting Cables Connecting the Power cable, VGA cable and RS-232 cable onto the FOX-12D and computer, and screw the three cables tightly on the FOX-12D as below. Before connecting the FOX-12D to the computer, remember to turn off the computer first. After each connector on the computer is secured, turn on the computer. Note: 1. The "Surge Protection" is already implemented 2. If it doesn't screw tightly, the water-proof function may not work. 3.
LCD Display FOX-12D 2.4 DC-IN 9~30V Connecter Pin Signal Pin Signal 1 DC V+ 2 N/A 3 GND 4 NC 2.5 Serial Port Connector For Touch Screen This pin definition of the connector will be referred when a touch screen has been installed. It must be connected to the RS-232 port of the PC.
LCD Display 9 Not Used FOX-12D 10 Not Used 2.6 VESA Wall Mounting Mounting the LCD Display with UL Listed Wallmount Bracket only. The LCD Display can be mounted on a monitor arm or wallmount plate. Caution: When mounting the LCD Display, take care to tighten the retention screws or bolts until fully secured, but do not over tighten. Over tighting the retention screws or bolts may cause them to become stripped, rendering them useless.
LCD Display FOX-12D VESA Mounting Holes To mount the LCD Display onto a monitor arm or wallmount plate, please follow the steps below. Step 1: Line up the threaded holes on the rear panel of the monitor with the screw holes on the monitor arm or wallmount plate. Step 2: Secure the monitor to the arm or stand with the retention screws supplied with the monitor arm or stand. 2.
LCD Display FOX-12D Step 2: Cut off the present RJ-45 plug cable Step 3: Put all parts of RJ-45 plug cable set through cable in order Step 4: Install and crimp a new RJ-45 plug Chapter 2 Hardware Installation 2-8
LCD Display FOX-12D Step 5: Insert RJ-45 plug into the socket and mount to cable set’s body.
LCD Display FOX-12D Step 7: Screw on the plastic rear nut a little bit for locking later.
LCD Display FOX-12D Step 8: Before locking the plastic rear nut tightly, press the cable hardly and make sure all parts of the LAN connector has been connected tightly Press hardly Lock the plastic rear nut Step 9: Tighten the plastic rear nut again to make sure the cable is securely connected and would not fall off accidentally Chapter 2 Hardware Installation 2-11
LCD Display FOX-12D Chapter 3 On Screen Display Control Chapter 3 On Screen Display Control 3-1
LCD Display FOX-12D 3.1 On Screen Display (OSD) Board Description Buttons Description Activate the OSD menu. Enter/confirm the selected option. Move the selector to the next option. UP / Right / Increase / Increase the gauge value of the Input select selected option. Menu / Enter Down/ Left / Decrease Change input source. Move the selector to the previous option. Decrease the gauge value of the selected option.
LCD Display FOX-12D 3.
LCD Display FOX-12D 3.
LCD Display FOX-12D 3.
LCD Display FOX-12D 3.
LCD Display FOX-12D 3.
LCD Display FOX-12D 3.
LCD Display FOX-12D 3.
LCD Display FOX-12D 3.
LCD Display FOX-12D 3.
LCD Display FOX-12D 3.
LCD Display FOX-12D Chapter 4 Touch Screen Driver Installation Chapter 4 Touch Screen Driver Installation 4-1
LCD Display FOX-12D 4.1 Introduction The optional FOX-12D Series touch screen uses 5-wire resistive technology to provide more accurate sensing capacity than other technologies. The touch screen is specially designed for tough industrial environments, and has been approved by CE/FCC Class A standards.
LCD Display FOX-12D 4.2 Resistive Touchscreen Control Board Hardware Touch screen controllers must be configured for the driver prior to installation. EETI typically ships controllers in a default setup that is compatible with this driver.
LCD Display FOX-12D HID drivers that provide low-level support for EETI touch screen controller. An EETI touch monitor with a USB touch screen controller installed will provide the following limited operation with these native HID drivers.
LCD Display FOX-12D 4.3 Installing Driver for Windows® XP/ Windows® 7 / Linux The touch screen has drivers for Windows® XP、 Windows® 7 and Linux . You should read the instructions in this chapter carefully before installation. Note 1: The following windows illustrations are examples only. You must follow the flow chart instructions and pay attention to the instructions which then appear on your screen.
LCD Display FOX-12D 2. Click the “Next” button on the screen 3. Click on the “Finish” button and restart your system Single monitor, Serial Port controller The driver files will install automatically. When the "Setup Complete" screen appears, you may choose to run calibration immediately or later. If you choose not to run this program now, you can run it from the EETI Control Panel application.
LCD Display FOX-12D 1. Executing eGalax on Desktop 2.
LCD Display FOX-12D 3. Choose Tools to calibrate 4. Click on 4 Points Calibration to execute calibration Note: If the alignments do not match display by 4 Points Calibration, please use 9 Ports or more to calibrate.
LCD Display FOX-12D For Windows® 7 OS please execute: CD-ROM: \\TouchScreen-DRV\eGalax Touch \Win 7 \Setup.exe 1. Click on the “Next” button 2.
LCD Display FOX-12D 3. Tick “None” if the system did not start 4 points calibrating after reboot. Click on the “Next” button. 4.
LCD Display FOX-12D 5. Select Destination Folder, and click on the “Next” button 6. Click on the “Next” button Single monitor, Serial Port controller The driver files will install automatically. When the "Setup Complete" screen appears, you may choose to run calibration immediately or later. If you choose not to run this program now, you can run it from the EETI Control Panel application.
LCD Display FOX-12D 1. Executing eGalax on Desktop 2.
LCD Display FOX-12D 3. Choose Tools to run calibration 4. Click on 4 Points Calibration to execute calibration Note: If the alignments do not match display by 4 Points Calibration, please use 9 Ports or more to calibrate.
LCD Display FOX-12D For Linux Fedora 14 kernel 2.6.35.6-45.fc14 OS please execute: CD-ROM: \\TouchScreen-DRV\eGalax Touch \Linux\eGalaxTouch 32 1. Open System Input Command (su) and System Password 2.
LCD Display FOX-12D 3. Input command ( cp /root/xorg.conf.new /etc/X11/xorg.conf) 4.
LCD Display 5. Executive Touch Driver 6.
LCD Display FOX-12D 7. Select the “ 3 ” USB interface. (Select the USB interface and press “Enter” key of the keyboard to start the installation) 8.
LCD Display FOX-12D 9. Reboot the system to activate the changes 10.
LCD Display FOX-12D 11. Select “eGalax Touch32_Version1.1-2.6X” Folder 12.
LCD Display FOX-12D 13. Click on the “eGalax Touch” to calibrate immediately 14.
LCD Display FOX-12D 15. Execute 4 Points Calibration Note: If the alignments do not match display by 4 Points Calibration, please use 9 Ports or more to calibrate. 16.
LCD Display FOX-12D 17. If you are going to replace the Interface, please remove the old Touch Driver (Input command: sh setup.sh uninstall) 18.
