F u l l-s i z e S B C F S B- 9 4 5 G FSB-945G ® TM Intel Core 2 Duo/ P4 /Celeron D LGA 775 Processor Full-size CPU Card With DDRII, Ethernet, IDE FSB-945G Manual Rev. A 1st Ed.
F u l l-s i z e C P U C a r d F S B- 9 4 5 G Copyright Notice This document is copyrighted, 2008. All rights are reserved. The original manufacturer reserves the right to make improvements to the products described in this manual at any time without notice. No part of this manual may be reproduced, copied, translat ed, or transmitted in any form or by any means without the prior written permission of the original manufacturer. Information provided in this manual is intended to be accurate and reliable.
F u l l-s i z e C P U C a r d F S B- 9 4 5 G Acknowledgments All other products’name or trademarks are properties of their respective owners. l Award is a trademark of Award Software International, Inc. l CompactFlash is a trademark of the Compact Flash Association. l Intel , Core 2 Duo are trademarks of Intel Corporation. l Microsoft Windows is a registered trademark of Microsoft Corp. l ITE is a trademark of Integrated Technology Express, Inc.
F u l l-s i z e C P U C a r d F S B- 9 4 5 G Packing List Before you begin installing your card, please make sure that the following materials have been shipped: l 1709070800 SATA Cable l 1701340704 Flat Cable l 1701400453 ATA-100 Cable l 1700060192 Keyboard and Mouse Cable l 1701260307 Flat Cable l 1701100305 Flat Cable with bracket l 1709100201 USB Cable w/ Bracket l Quick Installation Guide l CD-ROM for manual (in PDF format) and drivers l FSB-945G CPU Card If any of these it
F u l l-s i z e C P U C a r d F S B- 9 4 5 G Contents Chapter 1 General Information 1.1 Introduction ...........................................................1-2 1.2 Feature .................................................................1-3 1.3 Specification..........................................................1-4 Chapter 2 Quick Installation Guide 2.1 Safety Precautions .................................................2-2 2.2 Location of Connectors and Jumpers ......................2-3 2.
F u l l-s i z e C P U C a r d F S B- 9 4 5 G 2.18 PS2 Keyboard/Mouse Connector (CN4) ................2-13 2.19 Internal Keyboard Connector (CN5) ......................2-13 Chapter 3 Award BIOS Setup 3.1 System Test and Initialization..................................3-2 3.2 Award BIOS Setup .................................................3-3 Chapter 4 Driver Installation 4.1 Installation .............................................................4-3 Appendix A Programming The Watchdog Timer A.
F u l l-s i z e S B C F S B- 9 4 5 G Chapter 1 General Information Chapter 1 General Information 1-1
F u l l-s i z e S B C F S B- 9 4 5 G 1.1 Introduction AAEON announces a new full-size form factor Single Board Computer (SBC) with PICMG 1.0 - FSB-945G, which is based on the use of Intel® Core TM 2 Duo / P4 /Celeron D processors. ® TM FSB-945G utilizes Intel LGA 775 Core ® 2 Duo/Pentium 4 CPU with high CPU core frequencies with the Front Side Bus (FSB) running at 533 to 800MHz. FSB-945G supports DDRII 400/533/667 system memory up to 4GB.
F u l l-s i z e S B C F S B- 9 4 5 G planning and devices combination. . 1.2 Features l Compliance with PICMG 1.0 l Supports Intel® Core TM 2 Duo / P4 /Celeron D LGA775 CPUs , FSB 533/800 MHz (E4000, E2000, 600, 500, 300 series) l Supports DDR2 400/533 Memory up to 4GB l Integrated Intel Enhance Graphics Core, VGA Support l Supports two 10/100/1000Base-T Ethernet l Supports 4*SATA -300 ports l 7 USB 2.
F u l l-s i z e S B C F S B- 9 4 5 G 1.
F u l l-s i z e S B C F S B- 9 4 5 G Audio pin header for audio board option l IDE Interface: IDE connector x 1 l Universal Serial Bus: USB 2.0 Port on CPU card x 7/ 5x2 pin header for internal x 3/ TYPE-A Connector onboard x 1 l Watchdog Timer: 1~255 Step, can be set with software on Super I/O l RTC: Internal RTC l Power Supply Voltage: ATX12V connector for CPU, Other from Backplane l Board Size: 13.3” (L) x 4.98” (W) (338.58x126.39 mm) l Operation Temp.
F u l l-s i z e S B C F S B- 9 4 5 G pin header x 2) COM 1: RS -232 COM 2: RS -232/422/485 l Parallel Port: Supports SPP/EPP/ECP mode l Keyboard & Mouse connector: Mini-DIN for PS/2 Keyboard and mouse connector x 1; Internal keyboard pin header x 1 Chapter 1 General Information 1-6
Full-size SBC FSB-945G Chapter 2 Quick Installation Guide Notice: The Quick Installation Guide is derived from Chapter 2 of user manual. For other chapters and further installation instructions, please refer to the user manual CD-ROM that came with the product. Part No.
Full-size SBC FSB-945G 2.1 Safety Precautions Always completely disconnect the power cord from your board whenever you are working on it. Do not make connections while the power is on, because a sudden rush of power can damage sensitive electronic components. Always ground yourself to remove any static charge before touching the board. Modern electronic devices are very sensitive to static electric charges. Use a grounding wrist strap at all times.
Full-size SBC FSB-945G 2.
Full-size SBC Chapter 2 Quick Installation Guide 2 - 4 FSB-945G
Full-size SBC FSB-945G 2.
Full-size SBC Chapter 2 Quick Installation Guide 2 - 6 FSB-945G
Full-size SBC FSB-945G 2.4 List of Jumpers The board has a number of jumpers that allow you to configure your system to suit your application.
Full-size SBC FSB-945G 2.
Full-size SBC FSB-945G 2.6 Setting Jumpers You configure your card to match the needs of your application by setting jumpers. A jumper is the simplest kind of electric switch. It consists of two metal pins and a small metal clip (often protected by a plastic cover) that slides over the pins to connect them. To “close” a jumper you connect the pins with the clip. To “open” a jumper you remove the clip. Sometimes a jumper will have three pins, labeled 1, 2 and 3.
Full-size SBC FSB-945G 2.7 Clear CMOS (CMOS1) CMOS1 Function 1-2 Clear 2-3 Normal (default) 2.8 Front Panel Connector (FP1) Pin Signal Pin Signal 1 Power On Button (+) 2 Reset Switch (+) 3 Power On Button (-) 4 Reset Switch (-) 5 IDE LED (+) 6 Power LED (+) 7 IDE LED (-) 8 Power LED (-) 2.9 Front Panel Connector (FP2) Pin Signal Pin Signal 1 External Speaker (+) 2 Keyboard Lock (+) 3 N.C.
Full-size SBC FSB-945G 2.11 RS-232/422/485 Serial Port Connector (COM2) Pin Signal Pin Signal 1 DCD(422TXD-/485DATA-) 2 RXD(422RXD+) 3 TXD(422TXD+/485DATA+) 4 DTR(422RXD-) 5 GND 6 DSR 7 RTS 8 CTS 9 RI 10 N.C. 2.12 IrDA Connector (IR1) Pin Signal 1 +5V 2 N.C. 3 IRRX 4 GND 5 IRTX 6 N.C. 2.
Full-size SBC FSB-945G 19 #ACK 20 GND 21 BUSY 22 GND 23 PE 24 GND 25 SELECT 26 N.C. 2.14 USB Connector (USB2~4) Pin Signal Pin Signal 1 +5V 2 GND 3 USBD1- 4 GND 5 USBD1+ 6 USBD2+ 7 GND 8 USBD2- 9 GND 10 +5V 2.15 Fan Connector (FAN1) Pin Signal 1 GND 2 +12V or +5V 3 Speed Sense 4 FAN Out Control 2.
Full-size SBC FSB-945G 2.17 AC97 Connector (CN2) Pin Signal Pin Signal 1 AC_RST- 2 AC_SYNC 3 AC_DAIN2 4 AC_DAOUT 5 GND 6 AC_BCLK 7 GND 8 +5V 9 Lock 10 +3.3V 2.18 PS2 Keyboard/Mouse Connector (CN4) Pin Signal 1 KB_DATA 2 MS-DATA 3 GND 4 +5V 5 KB_CLK 6 MS_CLK 2.19 Internal Keyboard Connector (CN5) Pin Signal 1 KB_CLK 2 KB_DATA 3 N.C.
Full-size SBC FSB-945G Below Table for China RoHS Requirements 产品中有毒有害物质或元素名称及含量 AAEON Main Board/ Daughter Board/ Backplane 有毒有害物质或元素 部件名称 铅 汞 镉 六价铬 多溴联苯 多溴二苯醚 (Pb) (Hg) (Cd) (Cr(VI)) (PBB) (PBDE) × ○ ○ ○ ○ ○ × ○ ○ ○ ○ ○ 印刷电路板 及其电子组件 外部信号 连接器及线材 O：表示该有毒有害物质在该部件所有均质材料中的含量均在 SJ/T 11363-2006 标准规定的限量要求以下。 X：表示该有毒有害物质至少在该部件的某一均质材料中的含量超出 SJ/T 11363-2006 标准规定的限量要求。 备注：此产品所标示之环保使用期限，系指在一般正常使用状况下。 Chapter 2 Quick Installation Guide 2 - 14
F u l l-s i z e S B C F S B- 9 4 5 G Chapter 3 Award BIOS Setup Chapter 3 Award BIOS Setup 3-1
F u l l-s i z e S B C 3.1 F S B- 9 4 5 G System Test and Initialization These routines test and initialize board hardware. If the routines encounter an error during the tests, you will either hear a few short beeps or see an error message on the screen. There are two kinds of errors: fatal and non-fatal. The system can usually continue the boot up sequence with non-fatal errors.
F u l l-s i z e S B C 3.2 F S B- 9 4 5 G Award BIOS Setup Awards BIOS ROM has a built-in Setup program that allows users to modify the basic system configuration. This type of information is stored in battery-backed CMOS RAM so that it retains the Setup information when the power is turned off. Entering Setup Power on the computer and press immediately. This will allow you to enter Setup. Standard CMOS Features Use this menu for basic system configuration. (Date, time, IDE, etc.
F u l l-s i z e S B C F S B- 9 4 5 G Advanced Chipset Features Use this menu to change the values in the chipset registers and optimize your system performance. Integrated Peripherals Use this menu to specify your settings for integrated peripherals. (Primary slave, secondary slave, keyboard, mouse etc.) Power Management Setup Use this menu to specify your settings for power management. (HDD power down, power on by ring, KB wake up, etc.
F u l l-s i z e S B C F S B- 9 4 5 G Load Optimized Defaults Use this menu to load the BIOS default values that are factory settings for optimal performance system operations. While AWARD has designated the custom BIOS to maximize performance, the factory has the right to change these defaults to meet their needs. Set Supervisor/User Password Use this menu to set Supervisor/User Passwords. Save and Exit Setup Save CMOS value changes to CMOS and exit setup.
F u l l-s i z e S B C F S B- 9 4 5 G Chapter 4 Driver Installation Chapter 4 Driver Installation 4-1
F u l l-s i z e S B C F S B- 9 4 5 G The FSB-945G comes with a CD-ROM that contains all drivers your need. In addition, you can activate the installation items through Autorun program which will install each driver directly. If your system do not support Autorun program or you cannot install drivers successfully, please read instructions below for further detailed installations.
F u l l-s i z e S B C F S B- 9 4 5 G 4.1 Installation: Insert the FSB-945G CD-ROM into the CD-ROM Drive. And install the drivers from Step 1 to Step 4 in order. ® Step 1 – Install Intel INF Driver ® 1. Click on the Step 1 –Intel INF folder 2. Double click on the Setup file 3. Follow the instructions that the window shows 4. The system will help you install the driver automatically Step 2 – Install VGA Driver 1. Click on the Step 2 –VGA folder 2. Choose the OS your system is 3.
F u l l-s i z e S B C F S B- 9 4 5 G Step 4 – Install Audio Driver 1. Click on the Step 4 –Audio folder 2. Choose the OS your system is 3. Double click on the Setup file located in each OS folder 4. Follow the instructions that the window shows 5.
Full-size SBC FSB-945G Appendix A Programming the Watchdog Timer Appendix A Programming the Watchdog Timer A-1
Full-size SBC FSB-945G A.1 Programming FSB-945G utilizes W83627EHG chipset as its watchdog timer controller. Below are the procedures to complete its configuration and the AAEON intial watchdog timer program is also attached based on which you can develop customized program to fit your application.
Full-size SBC FSB-945G (3) Exit the W83627EHG config Mode. Undesired result may occur if the config Mode is not exited normally. (1) Enter the W83627EHG config Mode To enter the W83627EHG config Mode, two special I/O write operations are to be performed during Wait for Key state. To ensure the initial state of the key-check logic, it is necessary to perform two write operations to the Special Address port (2EH).
Full-size SBC FSB-945G = 10 Power LED pin is a 1Hz toggle pulse with 50 duty cycle. = 11 Power LED pin is a 1/4Hz toggle pulse with 50 duty cycle. Bit 5-4 : Reserved Bit 3 : select WDTO count mode. Bit 2 =0 second =1 minute : Enable the rising edge of keyboard Reset (P20) to force Time-out event.
Full-size SBC FSB-945G WatchDog Timer Register III (Index=F7h, Default=00h) Bit 7 Bit 6 : Mouse interrupt reset Enable or Disable =1 Watchdog Timer is reset upon a Mouse interrupt =0 Watchdog Timer is not affected by Mouse interrupt : Keyboard interrupt reset Enable or Disable =1 Watchdog Timer is reset upon a Keyboard interrupt =0 Watchdog Timer is not affected by Keyboard interrupt Bit 5 : Force Watchdog Timer Time-out.
Full-size SBC FSB-945G A.2 W83627EHG Watchdog Timer Initial Program Example: Setting 10 sec.
Full-size SBC FSB-945G ;/////////////////////////////////////////////////////////////////////////////////////////////// Dec dx Mov al,0f5h ;CRF5 (PLED mode register) Out dx,al Inc dx In al,dx And al,not 08h ;Set second as counting unit Out dx,al ;/////////////////////////////////////////////////////////////////////////////////////////////// Dec dx Mov al,0f6h ; CRF6 Out dx,al Inc dx Mov al,10 ;Set timeout interval as 10 sec.
Full-size SBC FSB-945G Appendix B I/O Information Appendix B I/O Information B-1
Full-size SBC B.
Full-size SBC FSB-945G B.
Full-size SBC B.3 IRQ Mapping Chart B.
Half-size SBC FSB-945G Appendix C Mating Connector Appendix C Mating Connector C - 1
Half-size SBC FSB-945G C.1 List of Mating Connectors and Cables The table notes mating connectors and available cables.
Half-size SBC ATX1 4P Power Connnecto r FAN1 FAN Connector USB1 USB Connector LAN1(-VE) Ethernet Connector LAN1(-G2) Ethernet Connector LAN2(-G2) Ethernet Connector IR1 IrDA Connector CN4 Mini-Din PS/2 Connector CN5 KB Pin Header COM1 Serial Port Box Header COM2 Serial Port Box Header VGA1 CRT Display Connector CN1 ATX Power Connector with BP FSB-945G Catch Electronics 1121-700-04S N/A Catch Electronics HO-BASE 1190-700-042 N/A KS-001V-ANW N/A BOTHHAND LU1T516-43 LF N/A BOTHHAND LA1T109D-D43 L
