N e t w o r k Ap p l i a n c e FWS-7600 FWS-7600 1U Rackmount Network Appliance Platform 1 ATA-100, 2 SATA II 6 USB Ports, Mini PCI FWS-7600 Manual 3rd Ed.
N e t w o r k Ap p l i a n c e FWS-7600 Copyright Notice This document is copyrighted, 2014. All rights are reserved. The original manufacturer reserves the right to make improvements to the products described in this manual at any time without notice. No part of this manual may be reproduced, copied, translated, or transmitted in any form or by any means without the prior written permission of the original manufacturer. Information provided in this manual is intended to be accurate and reliable.
N e t w o r k Ap p l i a n c e FWS-7600 Acknowledgments All other products’ name or trademarks are properties of their respective owners. Award is a trademark of Award Software International, Inc. CompactFlash™ is a trademark of the Compact Flash Association. Intel , Xeon Quad Core, and Core 2 Duo are trademarks of ® Intel Corporation. Microsoft Windows is a registered trademark of Microsoft Corp. ISoundBlaster is a trademark of Creative Labs, Inc.
N e t w o r k Ap p l i a n c e FWS-7600 Caution There is a danger of explosion if the battery is incorrectly replaced. Replace only with the same or equivalent type recommended by the manufacturer. Dispose of used batteries according to the manufacturer’s instructions and your local government’s recycling or disposal directives. Attention: Il y a un risque d’explosion si la batterie est remplacée de façon incorrecte. Ne la remplacer qu’avec le même modèle ou équivalent recommandé par le constructeur.
N e t w o r k Ap p l i a n c e FWS-7600 Packing List Before you begin installing your card, please make sure that the following materials have been shipped: 1 FWS-7600 1 Quick Installation Guide 1 CD-ROM for manual (in PDF format) and drivers 1 Heatpipe Module 1 Serial ATA Cable 1 Hard Disk Drive Power Cable 2 Ear Brackets Screw Accessories If any of these items should be missing or damaged, please contact your distributor or sales representative immediately.
N e t w o r k Ap p l i a n c e FWS-7600 Contents Chapter 1 General Information 1.1 Introduction ................................................................ 1-2 1.2 Features .................................................................... 1-3 1.3 Specifications ............................................................ 1-4 1.4 General System Information ..................................... 1-7 Chapter 2 Quick Installation Guide 2.1 Safety Precautions ...........................................
N e t w o r k Ap p l i a n c e FWS-7600 2.17 FAN Connector (FAN1, FAN2, FAN3) .................... 2-13 2.18 PS/2 Keyboard/ Mouse Connector (CN2) ............... 2-13 2.19 SATA Power Connector (PWR1) ............................ 2-13 2.20 LCM & Key Pad Control Connector (LCMA1) ......... 2-13 2.21 PCIX Power Connector (CN1) ................................ 2-14 2.22 Installing the CPU and the Heatpipe ....................... 2-15 2.23 Hard Disk Drive Installation .....................................
N e t w o r k Ap p l i a n c e FWS-7600 C.2 Status LED Sample Code ..................................... C-3 C.3 LAN Bypass Mode Sample Code ......................... C-6 C.4 LCM Sample Code ............................................... C-8 C.5 Console Redirection ...........................................
N e t w o r k Ap p l i a n c e FWS-7600 Chapter 1 General Information Chapter 1 General Information 1- 1
N e t w o r k Ap p l i a n c e FWS-7600 1.1 Introduction FWS-7600 adopts Intel Xeon Quad Core 3200 series up to 2.66GHz or Core 2 Duo 3000 series Processor up to 2.4GHz. The chipset is equipped with Intel® 3010 and Intel® 82801FB (ICH7R). In addition, the system memory features four 240-pin ECC DDRII 667 SDRAM DIMM socket total up to 8GB and supports dual-channel.
N e t w o r k Ap p l i a n c e FWS-7600 1.2 Features 1U Network Appliance Platform Up To 10 LAN Ports Intel® Xeon Quad Core 3200 Series Up to 2.66GHz & Dual Core 3000 Series CPU Up To 2.4GHz 240-Pin Dual-Channel ECC DDRII 667 SDRAM DIMM x 4 Support Up To 8GB Fiber Ethernet x 4 & Gigabit Ethernet Module x 4 For Optional (4-port Bypass Function) Ultra ATA-100 Port x 1 & SATA II x 2 CompactFlash Type-II Connector & Mini PCI Type-III Connector 300W Power With Auto Range Input USB2.
N e t w o r k Ap p l i a n c e FWS-7600 1.3 Specifications System 1U firewall heavy-duty steel system up Construction: to 10 ports Intel® Xeon Quad Core 3200 series up CPU to 2.66GHz and Dual Core 3000 series CPU up to 2.
N e t w o r k Ap p l i a n c e FWS-7600 Mini PCI Type III Socket & PCI/ Expansion Interface PCI-X/ PCI-E［x1］slot Note: FWS-7600 supports three types of add-on cards: PCI, PCI-X and PCI-Express, and not intended to use for any TELECOMMUNICATION NETWORK device. (Such as modem card.) Watchdog Timer 1~255 steps, can be set with software on Super I/O RTC Internal RTC Storage Internal：One 3.
N e t w o r k Ap p l i a n c e Universal Serial Bus FWS-7600 Six USB 2.0 Ports Two Dual Type A Connector on front panel Four Pin Header (Internal) Front I/O Panel One Bypass LED One Power LED One Status LED One HDD Active LED LAN LEDs Two USB Ports LAN Ports One DB-9 connector One LCM Display One Reset Button Rear I/O panel One PCI-E［x1］/ PCI-X/ PCI expansion slot Environmental Operating Temp. 32°F ~ 104°F (0°C ~ 40°C) Storage Temp.
N e t w o r k Ap p l i a n c e Shock FWS-7600 10G peak acceleration (11 m sec. duration), operation 20G peak acceleration (11 m sec.
N e t w o r k Ap p l i a n c e FWS-7600 1.4 General System Information Front Panel LEDs for Bypass, HDD Active, Status, Power 4 SFP Console Port 4 LAN Ports 2 USB Ports Modules could be two fiber modules or one fiber and one copper combination modules.
N e t w o r k Ap p l i a n c e FWS-7600 Chapter 2 FWS-7600 Quick Installation Guide Notice: The Quick Installation Guide is derived from Chapter 2 of the user manual. For other chapters and further installation instructions, please refer to the user manual CD-ROM that came with the product. Part No.
N e t w o r k Ap p l i a n c e FWS-7600 2.1 Safety Precautions The installation is intended for technically qualified personnel who have experience installing and configuring system boards. The equipment can be installed in a restricted access location (RAL) only. A restricted access location is a site location for equipment where the following criteria apply: 01. Access can only be gained by service persons or by users who have been trained on the restrictions and the precautions for this specific site.
N e t w o r k Ap p l i a n c e FWS-7600 2.
N e t w o r k Ap p l i a n c e 2.
N e t w o r k Ap p l i a n c e FWS-7600 Solder Side Chapter 2 Quick Installation Guide 2-5
N e t w o r k Ap p l i a n c e Mechanical Drawing of FWS-7600 Chapter 2 Quick Installation Guide 2-6 FWS-7600
N e t w o r k Ap p l i a n c e FWS-7600 2.4 List of Jumpers The board has a number of jumpers that allow you to configure your system to suit your application.
N e t w o r k Ap p l i a n c e FWS-7600 2.5 List of Connectors The board has a number of connectors that allow you to configure your system to suit your application.
N e t w o r k Ap p l i a n c e FWS-7600 2.6 Setting Jumpers You configure your card to match the needs of your application by setting jumpers. A jumper is the simplest kind of electric switch. It consists of two metal pins and a small metal clip (often protected by a plastic cover) that slides over the pins to connect them. To “close” a jumper you connect the pins with the clip. To “open” a jumper you remove the clip. Sometimes a jumper will have three pins, labeled 1, 2 and 3.
N e t w o r k Ap p l i a n c e FWS-7600 2.7 CF Power Selection (JP3) JP3 Function Close 1-2 +5V (Default) Close 2-3 +3.3V 2.8 Clear CMOS (JP4) JP4 Function 1-2 Clear CMOS Open Protected (Default) 2.9 BUZZER (FP2) FP2 Function 5-7 Enable Internal SPK (Default) Open Disable Internal SPK 2.
N e t w o r k Ap p l i a n c e FWS-7600 5 Internal Buzzer (-) 6 7 External Speaker (-) 8 I2C Bus SMB Clock Note: Internal Buzzer enable: Close Pin 5,7 2.12 USB Connector (USB1) Pin Signal Pin Signal 1 +5V 2 GND 3 USBD- 4 GND 5 USBD+ 6 USBD+ 7 GND 8 USBD- 9 GND 10 +5V 2.13 USB Pin Header (CN4, CN6) Pin Signal Pin Signal 1 +5V 2 GND 3 USBD- 4 GND 5 USBD+ 6 USBD+ 7 GND 8 USBD- 9 GND 10 +5V 2.
N e t w o r k Ap p l i a n c e FWS-7600 7 RTS 8 CTS 9 RI 10 NC 2.15 RS-232 Serial Port Pin Header (COM2) Pin Signal Pin Signal 1 DCD 2 RXD 3 TXD 4 DTR 5 GND 6 DSR 7 RTS 8 CTS 9 RI 10 NC 2.16 Power Connector (ATX2) Pin Signal Pin Signal 1 +3.3V 2 +3.3V 3 GND 4 +5V 5 GND 6 +5V 7 GND 8 PWROK 9 +5VSB 10 +12V 11 +12V 12 +3.3V 13 +3.
N e t w o r k Ap p l i a n c e 23 +5V FWS-7600 24 GND 2.17 FAN Connector (FAN1, FAN2, FAN3) Pin Signal Pin Signal 1 GND 2 +12V 3 SENCE 2.18 PS/2 Keyboard/ Mouse Connector (CN2) CN2 Function 1 KB_DATA 2 KB_CLK 3 GND 4 +5V 5 MS_DATA 6 MS_CLK 7 NC 8 NC 2.19 SATA Power Connector (PWR1) Pin Signal Pin Signal 1 +12V 2 GND 3 GND 4 +5V 2.
N e t w o r k Ap p l i a n c e FWS-7600 3 LSLIN- 4 VEE 5 LAFD- 6 LINIT- 7 LPD1 8 LPD0 9 LPD3 10 LPD2 11 LPD5 12 LPD4 13 LPD7 14 LPD6 15 LCD- 16 VCC 17 UP 18 RIGHT 19 LEFT 20 DOWN 21 RESET 22 NC 23 NC 24 NC 2.21 PCIX Power Connector (CN1) Pin Signal Pin Signal 1 GND 2 +3.3V 3 +3.3V 4 +3.
N e t w o r k Ap p l i a n c e FWS-7600 2.
N e t w o r k Ap p l i a n c e Step 3: Lift up the socket Step 4: Put the CPU on the socket Chapter 2 Quick Installation Guide 2-16 FWS-7600
N e t w o r k Ap p l i a n c e FWS-7600 Step 5: Lock the CPU Socket Step 6: The heatpipe module is already with thermal paste Chapter 2 Quick Installation Guide 2-17
N e t w o r k Ap p l i a n c e FWS-7600 Step 7: Remove the transparent cap Step 8: Put the heatpipe on the motherboard where the socket has already been put on CPU in the chassis Chapter 2 Quick Installation Guide 2-18
N e t w o r k Ap p l i a n c e FWS-7600 Step 9: Be sure the heatpipe has been put in the right position against the vent properly Step 10: Fasten the four screws of the heatpipe Chapter 2 Quick Installation Guide 2-19
N e t w o r k Ap p l i a n c e FWS-7600 Step 11: Put the fan module back to the original place, and fasten these two screws of the fan module 2.
N e t w o r k Ap p l i a n c e FWS-7600 Step 2: Lift up the hard disk drive bracket aside Step 3: Fasten the hard disk in the driver bay by using the four screws Chapter 2 Quick Installation Guide 2-21
N e t w o r k Ap p l i a n c e FWS-7600 Step 4: Lift down the hard disk drive and push into the bracket Step 5: Fasten the hard disk driver bay by using the screws Chapter 2 Quick Installation Guide 2-22
N e t w o r k Ap p l i a n c e FWS-7600 Step 6: Connect the SATA cable and power cable into the Hard Disk 2.
N e t w o r k Ap p l i a n c e FWS-7600 Step 2: Remove the null Module cover or LAN module Chapter 2 Quick Installation Guide 2-24
N e t w o r k Ap p l i a n c e FWS-7600 Step 3: Insert the LAN Module and fasten the screws Chapter 2 Quick Installation Guide 2-25
N e t w o r k Ap p l i a n c e FWS-7600 Below Table for China RoHS Requirements 产品中有毒有害物质或元素名称及含量 AAEON Boxer/ Industrial System 有毒有害物质或元素 部件名称 铅 汞 镉 (Pb) (Hg) (Cd) (Cr(VI)) (PBB) (PBDE) × ○ ○ ○ ○ ○ × ○ ○ ○ ○ ○ × ○ ○ ○ ○ ○ × ○ ○ ○ ○ ○ 硬盘 × ○ ○ ○ ○ ○ 电源 × ○ ○ ○ ○ ○ 印刷电路板 及其电子组件 外部信号 连接器及线材 外壳 中央处理器 与内存 六价铬 多溴联苯 多溴二苯醚 O：表示该有毒有害物质在该部件所有均质材料中的含量均在 SJ/T 11363-2006 标准规定的限量要求以下。 X：表示该有毒有害物质至少在该部件的某一均质材料中的含量超出 SJ/T 11363-2006 标准规定的限量要求。 备注： 一、此产品所标示之环保使用期限，系指在一般正常
N e t w o r k Ap p l i a n c e FWS-7600 Chapter 3 Award BIOS Setup Chapter 3 Award BIOS Setup 3-1
N e t w o r k Ap p l i a n c e 3.1 FWS-7600 System Test and Initialization These routines test and initialize board hardware. If the routines encounter an error during the tests, you will either hear a few short beeps or see an error message on the screen. There are two kinds of errors: fatal and non-fatal. The system can usually continue the boot up sequence with non-fatal errors.
N e t w o r k Ap p l i a n c e 3.2 FWS-7600 Award BIOS Setup Awards BIOS ROM has a built-in Setup program that allows users to modify the basic system configuration. This type of information is stored in battery-backed CMOS RAM so that it retains the Setup information when the power is turned off. Entering Setup Power on the computer and press immediately. This will allow you to enter Setup. Standard CMOS Features Use this menu for basic system configuration. (Date, time, IDE, etc.
N e t w o r k Ap p l i a n c e FWS-7600 Advanced Chipset Features Use this menu to change the values in the chipset registers and optimize your system performance. Integrated Peripherals Use this menu to specify your settings for integrated peripherals. (Primary slave, secondary slave, keyboard, mouse etc.) Power Management Setup Use this menu to specify your settings for power management. (HDD power down, power on by ring, KB wake up, etc.
N e t w o r k Ap p l i a n c e FWS-7600 Load Optimized Defaults Use this menu to load the BIOS default values that are factory settings for optimal performance system operations. While AWARD has designated the custom BIOS to maximize performance, the factory has the right to change these defaults to meet their needs. Set Supervisor/User Password Use this menu to set Supervisor/User Passwords. Save and Exit Setup Save CMOS value changes to CMOS and exit setup.
N e t w o r k Ap p l i a n c e FWS-7600 Chapter 4 Driver Installation Chapter 4 Driver Installation 4-1
N e t w o r k Ap p l i a n c e FWS-7600 The FWS-7600 comes with an AutoRun CD-ROM that contains all drivers and utilities that can help you to install the driver automatically. Insert the driver CD, the driver CD-title will auto start and show the installation guide. If not, please follow the sequence below to install the drivers. Follow the sequence below to install the drivers: Step 1 – Install INF Driver Step 2 – Install LAN Driver USB 2.
N e t w o r k Ap p l i a n c e 4.1 FWS-7600 Installation: Insert the FWS-7600 CD-ROM into the CD-ROM drive and install the drivers from Step 1 to Step 2 in order. Step 1 – Install INF Driver 1. Click on the Step 1-INF folder and double click on the Setup file 2. Follow the instructions that the window shows 3. The system will help you install the driver automatically Step 2 – Install LAN Driver 1. Click on the Step 2 –LAN folder and double click on the Autorun file 2.
N e t w o r k Ap p l i a n c e FWS-7600 Appendix A Programming the Watchdog Timer Appendix A Programming the Watchdog Timer A-1
N e t w o r k Ap p l i a n c e FWS-7600 A.1 Programming FWS-7600 utilizes W83627EHG chipset as its watchdog timer controller. Below are the procedures to complete its configuration and the AAEON intial watchdog timer program is also attached based on which you can develop customized program to fit your application.
N e t w o r k Ap p l i a n c e FWS-7600 (2) Modify the data of configuration registers (3) Exit the W83627EHG config Mode. Undesired result may occur if the config Mode is not exited normally. (1) Enter the W83627EHG config Mode To enter the W83627EHG config Mode, two special I/O write operations are to be performed during Wait for Key state. To ensure the initial state of the key-check logic, it is necessary to perform two write operations to the Special Address port (2EH).
N e t w o r k Ap p l i a n c e FWS-7600 = 01 Power LED pin is drived low. = 10 Power LED pin is a 1Hz toggle pulse with 50 duty cycle. = 11 Power LED pin is a 1/4Hz toggle pulse with 50 duty cycle. Bit 5-4 : Reserved Bit 3 : select WDTO count mode. Bit 2 =0 second =1 minute : Enable the rising edge of keyboard Reset (P20) to force Time-out event.
N e t w o r k Ap p l i a n c e FWS-7600 second/minutes WatchDog Timer Register III (Index=F7h, Default=00h) Bit 7 Bit 6 : Mouse interrupt reset Enable or Disable =1 Watchdog Timer is reset upon a Mouse interrupt =0 Watchdog Timer is not affected by Mouse interrupt : Keyboard interrupt reset Enable or Disable =1 Watchdog Timer is reset upon a Keyboard interrupt =0 Watchdog Timer is not affected by Keyboard interrupt Bit 5 : Force Watchdog Timer Time-out.
N e t w o r k Ap p l i a n c e FWS-7600 A.2 W83627EHG Watchdog Timer Initial Program Example: Setting 10 sec.
N e t w o r k Ap p l i a n c e FWS-7600 ;/////////////////////////////////////////////////////////////////////////////////////////////// Dec dx Mov al,0f5h ;CRF5 (PLED mode register) Out dx,al Inc dx In al,dx And al,not 08h ;Set second as counting unit Out dx,al ;/////////////////////////////////////////////////////////////////////////////////////////////// Dec dx Mov al,0f6h ; CRF6 Out dx,al Inc dx Mov al,10 ;Set timeout interval as 10 sec.
N e t w o r k Ap p l i a n c e FWS-7600 Appendix B I/O Information Appendix B I/O Information B-1
N e t w o r k Ap p l i a n c e B.
N e t w o r k Ap p l i a n c e FWS-7600 B.
N e t w o r k Ap p l i a n c e B.3 IRQ Mapping Chart B.
N e t w o r k Ap p l i a n c e FWS-7600 Appendix C Standard Firewall Platform Setting Appendix C Standard Firewall Platform Setting C-1
N e t w o r k Ap p l i a n c e FWS-7600 C.
N e t w o r k Ap p l i a n c e FWS-7600 C.
N e t w o r k Ap p l i a n c e FWS-7600 out dx,al [RED LED BLINK] mov dx,48Fh ;( IO_PORT = 48Fh) in al,dx or al,00010000b ;set bit 4 -->high out dx,al mov dx,4B8h ;( IO_PORT = 4B8h) in al,dx and al,11110111b ;set bit 3 -->low out dx,al mov dx,49Bh ;( IO_PORT = 49Bh) in al,dx or al,00010000b ;set bit 4 -->high(control blink) out dx,al [GREEN LED ON] mov dx,48Fh ;( IO_PORT = 48Fh) in al,dx and al,11101111b ;set bit 4 -->low out dx,al mov dx,4B8h Appendix C Standard Firewall Platform Setting C-4
N e t w o r k Ap p l i a n c e FWS-7600 in al,dx or al,00001000b ;set bit 3 -->high out dx,al [GRN LED BLINK] mov dx,48Fh ;( IO_PORT = 48Fh) in al,dx and al,11101111b ;set bit 4 -->low out dx,al mov dx,4B8h ;( IO_PORT = 4B8h) in al,dx or al,00001000b ;set bit 3 -->high out dx,al mov dx,49Bh ;( IO_PORT = 49Bh) in al,dx or al,00010000b ;set bit 4 -->high(control blink) out dx,al Appendix C Standard Firewall Platform Setting C-5
N e t w o r k Ap p l i a n c e FWS-7600 C.
N e t w o r k Ap p l i a n c e FWS-7600 [Watch Dog Mode] mov dx,48dh ;( IO_PORT = 48dh) in al,dx or al,01000000b ;set bit 7-->high out dx,al mov dx,48Fh ;( IO_PORT = 48Fh) in al,dx or al,00000100b ;set bit 2-->high out dx,al Appendix C Standard Firewall Platform Setting C-7
N e t w o r k Ap p l i a n c e C.
N e t w o r k Ap p l i a n c e FWS-7600 } void Entry_mode_set() { outportb(0x378, 0x06); wait(); outportb(0x37A, 0xC8); wait(); outportb(0x37A, 0xCA); wait(); } void Display_Off() { outportb(0x378, 0x08); wait(); outportb(0x37A, 0xC8); wait(); outportb(0x37A, 0xCA); Appendix C Standard Firewall Platform Setting C-9
N e t w o r k Ap p l i a n c e wait(); } void Display_On_Cursor_Off() { outportb(0x378, 0x0C); wait(); outportb(0x37A, 0xC8); wait(); outportb(0x37A, 0xCA); wait(); } void Display_On_Cursor_On() { outportb(0x378, 0x0E); wait(); outportb(0x37A, 0xC8); wait(); Appendix C Standard Firewall Platform Setting C-10 FWS-7600
N e t w o r k Ap p l i a n c e FWS-7600 outportb(0x37A, 0xCA); wait(); } /******************************************************************** ****/ // Set the interface data length. // Number of display line and character font. // For 5x7 dots and 2 lines display now.
N e t w o r k Ap p l i a n c e wait(); } void Write_Char( char x ) { outportb(0x378, x); outportb(0x37A, 0xC0); wait(); outportb(0x37A, 0xC2); wait(); } void Change_Line() { outportb(0x378, 0xC0); wait(); outportb(0x37A, 0xC8); wait(); outportb(0x37A, 0xCA); Appendix C Standard Firewall Platform Setting C-12 FWS-7600
N e t w o r k Ap p l i a n c e FWS-7600 wait(); } void wait() { for (int i = 0 ; i < 0x10 ; i++) { for (int j = 0 ; j < 0x80 ; j++) { outportb(0x0EB, 0Xff); } } } Appendix C Standard Firewall Platform Setting C-13
N e t w o r k Ap p l i a n c e FWS-7600 C.5 Console Redirection Console redirection allows you to maintain a system from a remote location by re-directing keyboard input and text output through the serial port. This section will tell you how to use the console redirection. 1. Please insert console cable between on FWS-7600 and remote client system. 2. Setup BIOS in FWS-7600.
N e t w o r k Ap p l i a n c e FWS-7600 Step4 - From the connect to pull-down menu, select a COM port available on your client system and click OK Step5 - Select Baud Rate >> 19200, Flow control >> None, Data bit >>8, Parity cheek >> None, Stop bit>>1 4. Power on FWS-7600 and it will display the BIOS information on the client system.
