N e t w o r k Ap p l i a n c e FWS-816B FWS-816B 1U Rackmount Network Appliance Platform 1 3.5” Disk Drive bay 8 LAN Ports 2 Type A USB Ports FWS-816 Manual Rev. B 2nd Ed.
N e t w o r k Ap p l i a n c e FWS-816B Copyright Notice This document is copyrighted, 2014. All rights are reserved. The original manufacturer reserves the right to make improvements to the products described in this manual at any time without notice. No part of this manual may be reproduced, copied, translated, or transmitted in any form or by any means without the prior written permission of the original manufacturer. Information provided in this manual is intended to be accurate and reliable.
N e t w o r k Ap p l i a n c e FWS-816B Acknowledgments All other products’ name or trademarks are properties of their respective owners. Award is a trademark of Award Software International, Inc. CompactFlash™ is a trademark of the Compact Flash Association. Intel , Pentium M, and Core 2 Duo are trademarks of Intel Corporation. Microsoft Windows is a registered trademark of Microsoft Corp. ISoundBlaster is a trademark of Creative Labs, Inc.
N e t w o r k Ap p l i a n c e FWS-816B Caution There is a danger of explosion if the battery is incorrectly replaced. Replace only with the same or equivalent type recommended by the manufacturer. Dispose of used batteries according to the manufacturer’s instructions and your local government’s recycling or disposal directives. Attention: Il y a un risque d’explosion si la batterie est remplacée de façon incorrecte. Ne la remplacer qu’avec le même modèle ou équivalent recommandé par le constructeur.
N e t w o r k Ap p l i a n c e FWS-816B Packing List Before you begin installing your card, please make sure that the following materials have been shipped: 1 FWS-816B 1 Quick Installation Guide 1 CD-ROM for manual (in PDF format) and drivers 1 Heatpipe Module 1 Serial ATA Cable 1 Hard Disk Drive Power Cable 2 Ear Brackets Screw Accessories If any of these items should be missing or damaged, please contact your distributor or sales representative immediately.
N e t w o r k Ap p l i a n c e FWS-816B Contents Chapter 1 General Information 1.1 Introduction ................................................................ 1-2 1.2 Features .................................................................... 1-3 1.3 Specifications ............................................................ 1-4 1.4 General System Information ..................................... 1-7 Chapter 2 Quick Installation Guide 2.1 Safety Precautions ...........................................
N e t w o r k Ap p l i a n c e FWS-816B 2.17 RJ-45 Phone Jack Connector (LAN1-8).................. 2-11 2.18 PS2 Keyboard/ Mouse Connector (CN7) ................ 2-12 2.19 SATA Power Connector (PWR1) ............................ 2-12 2.20 LCM & Key Pad Control Connector (LCMA1) ......... 2-12 2.21 Power Connector for PCI-X Riser (CN8)................. 2-13 2.22 Removing the Cover................................................ 2-14 2.23 Installing the CPU and the Heatpipe ....................... 2-15 2.
N e t w o r k Ap p l i a n c e FWS-816B Appendix C Standard Firewall Platform Setting C.1 Standard Firewall Platform Setting ....................... C-2 C.2 Status LED Sample Code ..................................... C-3 C.3 LAN Bypass Mode Sample Code ......................... C-6 C.4 LCM Sample Code ............................................... C-8 C.5 Console Redirection ...........................................
N e t w o r k Ap p l i a n c e FWS-816B Chapter 1 General Information Chapter 1 General Information 1- 1
N e t w o r k Ap p l i a n c e FWS-816B 1.1 Introduction FWS-816 Rev.B adopts the Core 2 Duo LGA 775 Processor, up to 2.66GHz with 533/800/1066 Front Side Bus. Moreover, the chipset is equipped with Intel® 945G and Intel® 82801FB (ICH7R). The system memory features 2x240-pin DDRII 667 SDRAM DIMM socket total up to 4GB and supports dual channel. It deploys eight LAN ports that consist of six PCIe Gigabit Ethernet LAN ports with two ports bypass function and two 10/100Base-TX LAN ports.
N e t w o r k Ap p l i a n c e FWS-816B 1.2 Features 1U eight LAN ports network appliance platform Intel® Core 2 Duo CPU up to 2.66GHz (Dual Core up to 3.6GHz) (Tc =70.8o @ 115W) 2x240-pin dual channel DDRII 667 SDRAM DIMM support up to 4GB (DIMM Height under 31mm) Six 10/100/1000Base-TX ports (2 ports bypass function) & two 10/100 Ethernet ports One Ultra ATA-100 port & two SATA II ports CompactFlash Type-II connector & DOM up to 2GB (DOM Height under 29mm) 250W power with auto range input Six USB2.
N e t w o r k Ap p l i a n c e FWS-816B 1.3 Specifications System Construction: 1U 8-port firewall heavy-duty steel system CPU Intel® Core 2 Duo LGA775 up to 2.66GHz (FSB 400/533/800/1066, Dual Core up to 3.6GHz ) (Tc =70.
N e t w o r k Ap p l i a n c e FWS-816B System Fan Three 4cm Ball Bearing Fans Color Blue and Red LCM 2 x16 characters with 4 keypad control Power Supply ATX 250W, auto range Dimensions 16.93” (W) x 14.96” (D) x 1.73”(H) (430mm x 380mm x 44mm) —Chassis 9.84” (W) x 11.02” (D) (250mm x 280mm) —Board Net Weight 17.
N e t w o r k Ap p l i a n c e FWS-816B Two USB Ports Eight LAN Ports One DB-9 connector One LCM Display One Reset Button Rear I/O panel One PCI-E［x1］/ PCI-X/ PCI expansion slot (Optional) Environmental Operating Temp. 32°F ~ 104°F (0°C ~ 40°C) Storage Temp. -4°F ~ 140°F (-20°C ~ 60°C) Operating humidity: 10 ~ 80% Storage humidity: 10 ~ 80% @ 40°C, non-condensing Vibration 0.5G / 5 ~ 500Hz / operation (3.5” Hard Disk Drive) 1.5G / 5 ~ 500Hz / non operation Shock 10G peak acceleration (11 m sec.
N e t w o r k Ap p l i a n c e FWS-816B 1.4 General System Information Front Panel LEDs for Bypass, HDD Active, Status, Power Handle Reset 2 USB Ports LCM Display 8 LAN Ports Keypad Control Console Port Inside CPU Heatpipe 1U Power Supply Heatsink & Fan PCI Riser Mini PCI CompactFlash 8 LAN Chipsets 3.
Ne tw ork Ap p lia nce FWS-816B Chapter 2 FWS-816B Quick Installation Guide Notice: The Quick Installation Guide is derived from Chapter 2 of the user manual. For other chapters and further installation instructions, please refer to the user manual CD-ROM that came with the product. Part No. 2001816020 Printed in Taiwan Nov.
Ne tw ork Ap p lia nce FWS-816B 2.1 Safety Precautions The installation is intended for technically qualified personnel who have experience installing and configuring system boards. The equipment can be installed in a restricted access location (RAL) only. A restricted access location is a site location for equipment where the following criteria apply: 01. Access can only be gained by service persons or by users who have been trained on the restrictions and the precautions for this specific site. 02.
Ne tw ork Ap p lia nce FWS-816B 2.
Ne tw ork Ap p lia nce FWS-816B 2.
Ne tw ork Ap p lia nce FWS-816B 2.4 List of Jumpers The board has a number of jumpers that allow you to configure your system to suit your application.
Ne tw ork Ap p lia nce FWS-816B 2.5 List of Connectors The board has a number of connectors that allow you to configure your system to suit your application.
Ne tw ork Ap p lia nce FWS-816B 2.6 Setting Jumpers You configure your card to match the needs of your application by setting jumpers. A jumper is the simplest kind of electric switch. It consists of two metal pins and a small metal clip (often protected by a plastic cover) that slides over the pins to connect them. To “close” a jumper you connect the pins with the clip. To “open” a jumper you remove the clip. Sometimes a jumper will have three pins, labeled 1, 2 and 3.
Ne tw ork Ap p lia nce FWS-816B 2.7 Clear CMOS (JP1) JP1 Function 1-2 Clear Open Protected (Default) 2.8 Front Panel Connector (FP1) Pin Signal Pin Signal 1 Power On Button (+) 2 Reset Switch (+) 3 Power On Button (-) 4 Reset Switch (-) 5 IDE LED (+) 6 Power LED (+) 7 IDE LED (-) 8 Power LED (-) 2.
Ne tw ork Ap p lia nce FWS-816B 2.10 USB Connector (USB1) Pin Signal Pin Signal 1 GND 2 XUSBD4+ 3 XUSBD4- 4 +5V 5 GND 6 XUSBD5+ 7 XUSBD5- 8 +5V Note: When activating the COM port LL5 test, please “Disable” the USB keyboard and mouse in BIOS setting. 2.11 USB Pin Header (CN4, CN5) Pin Signal Pin Signal 1 +5V 2 GND 3 USBD- 4 GND 5 USBD+ 6 USBD+ 7 GND 8 USBD- 9 GND 10 +5V 2.
Ne tw ork Ap p lia nce 7 RTS 9 RI FWS-816B 8 CTS 2.13 Power Connector (ATX2) Pin Signal Pin Signal 1 +3.3V 2 +3.3V 3 GND 4 +5V 5 GND 6 +5V 7 GND 8 PWROK 9 +5VSB 10 +12V 11 +12V 12 +3.3V 13 +3.3V 14 -12V 15 GND 16 PS_ON 17 GND 18 GND 19 GND 20 NC 21 +5V 22 +5V 23 +5V 24 GND 2.
Ne tw ork Ap p lia nce FWS-816B 5 VGA B 6 NC 7 NC 8 VGA DATA 9 GND 10 VGA HS 11 GND 12 VGA VS 13 GND 14 VGA CLK 15 GND 16 NC 2.15 FAN Connector (CPUFAN1) Pin Signal Pin Signal 1 GND 2 +12V 3 SENCE 4 CTRL 2.16 FAN Connector (FAN1, FAN2, FAN3) Pin Signal Pin Signal 1 GND 2 +12V 3 SENCE 2.
Ne tw ork Ap p lia nce FWS-816B 7 T78 8 T78 9 BLINK100- 10 BLINK1G- 11 BACT 12 +3.3V 13 GND 14 GND 2.18 PS2 Keyboard/ Mouse Connector (CN7) Pin Signal 1 KB_DATA 2 KB_CLK 3 GND 4 +5V 5 MS_DATA 6 MS_CLK- 2.19 SATA Power Connector (PWR1) Pin Signal Pin Signal 1 +12V 2 GND 3 GND 4 +5V 2.
Ne tw ork Ap p lia nce FWS-816B 5 LAFD- 6 LINIT- 7 LPD1 8 LPD0 9 LPD3 10 LPD2 11 LPD5 12 LPD4 13 LPD7 14 LPD6 15 LCD- 16 VCC 17 UP 18 RIGHT 19 LEFT 20 DOWN 21 RESET 22 NC 23 NC 24 NC 2.21 Power Connector for PCI-X Riser (CN8) Pin Signal Pin Signal 1 GND 2 +3.3V 3 +3.3V 4 +3.
Ne tw ork Ap p lia nce FWS-816B 2.22 Removing the Cover Before you install drives or plug-in cards into the FWS-816B, please switch the unit off and remove the power cord first.
Ne tw ork Ap p lia nce FWS-816B 2.
Ne tw ork Ap p lia nce FWS-816B Step 3: Loosen these two screws and pull off the power cable of the three fans Step 4: Lift up the fan module aside Fan Module Chapter 2 Quick Installation Guide 2-16
Ne tw ork Ap p lia nce Step 5: Lift up the socket FWS-816B Step 6: Put the CPU on socket CPU Step 7: Lock the CPU Socket Step 8: The Heatpipe module is already with thermal paste Heatpipe Chapter 2 Quick Installation Guide 2-17
Ne tw ork Ap p lia nce FWS-816B Step 9: Remove the transparent cap Step 10: Put the heatpipe on the Motherboard where the socket has already been put on CPU in the Chassis Chapter 2 Quick Installation Guide 2-18
Ne tw ork Ap p lia nce FWS-816B Step 11: Be sure the heatpipe has been put in the right position against the vent properly Step 12: Fasten the four screws of the heatpipe Chapter 2 Quick Installation Guide 2-19
Ne tw ork Ap p lia nce FWS-816B Step 13: Put the fan module back to the original place Step 14: Fasten the two screws of the fan module and plug in the power cable Power cable Chapter 2 Quick Installation Guide 2-20
Ne tw ork Ap p lia nce FWS-816B Step 15: Insert the Power cable of Fan Module Step 16: Insert 12V Power Cable Power cables of FAN Module are under the 12V Power Cable Chapter 2 Quick Installation Guide 2-21
Ne tw ork Ap p lia nce FWS-816B Step 17: Collect the power cable of Fan Module under the bracket for storage Note: Please pull the power cable tightly and keep it off the FAN Step 18: Insert the white tape into the bracket to fix the power cable of Fan Module Chapter 2 Quick Installation Guide 2-22
Ne tw ork Ap p lia nce FWS-816B 2.
Ne tw ork Ap p lia nce FWS-816B Step 3: Fasten the Hard Disk Drive Bracket with the back side of Hard Disk Drive by using the four screws Step 4: Overturn the Hard Disk Drive and put it into the chassis Chapter 2 Quick Installation Guide 2-24
Ne tw ork Ap p lia nce FWS-816B Step 5: Fasten the four screws of the Hard Disk Drive Bracket Chapter 2 Quick Installation Guide 2-25
Ne tw ork Ap p lia nce FWS-816B 2.25 Installing the Add-on Card FWS-816B supports three types of add-on cards: PCI, PCI-X and PCI-Express, and not intended to use for any TELECOMMUNICATION NETWORK device. (Such as modem card.
Ne tw ork Ap p lia nce FWS-816B Step 3: Pull up the drawstring of the cover and hold Step 4: Connect the top of the Bracket to the cover and release the drawstring Note: There is an indentation on the bracket and you will see a hole on the cover when you pull up the drawstring. Please make sure the indentation has been placed to the hole on the cover and then release the drawstring to lock the card firmly.
Ne tw ork Ap p lia nce FWS-816B Step 5: Insert the Add-on card to the FWS-816B Round silver mark L Shape indentation Note: There is a round silver mark on the top of the front panel. Please make sure the L shape indentation on the cover has been aimed at the mark when you insert the card to the FWS-816B.
Ne tw ork Ap p lia nce FWS-816B Chapter 2 Quick Installation Guide 2-29
Ne tw ork Ap p lia nce FWS-816B Below Table for China RoHS Requirements 产品中有毒有害物质或元素名称及含量 AAEON Boxer/ Industrial System 有毒有害物质或元素 部件名称 铅 汞 镉 (Pb) (Hg) (Cd) (Cr(VI)) (PBB) (PBDE) × ○ ○ ○ ○ ○ × ○ ○ ○ ○ ○ × ○ ○ ○ ○ ○ × ○ ○ ○ ○ ○ 硬盘 × ○ ○ ○ ○ ○ 电源 × ○ ○ ○ ○ ○ 印刷电路板 及其电子组件 外部信号 连接器及线材 外壳 中央处理器 与内存 六价铬 多溴联苯 多溴二苯醚 O：表示该有毒有害物质在该部件所有均质材料中的含量均在 SJ/T 11363-2006 标准规定的限量要求以下。 X：表示该有毒有害物质至少在该部件的某一均质材料中的含量超出 SJ/T 11363-2006 标准规定的限量要求。 备注： 一、此产品所标示之环保使用期限，系指在一般正常使用状况下。 二
N e t w o r k Ap p l i a n c e FWS-816B Chapter 3 Award BIOS Setup Chapter 3 Award BIOS Setup 3-1
N e t w o r k Ap p l i a n c e 3.1 FWS-816B System Test and Initialization These routines test and initialize board hardware. If the routines encounter an error during the tests, you will either hear a few short beeps or see an error message on the screen. There are two kinds of errors: fatal and non-fatal. The system can usually continue the boot up sequence with non-fatal errors.
N e t w o r k Ap p l i a n c e 3.2 FWS-816B Award BIOS Setup Awards BIOS ROM has a built-in Setup program that allows users to modify the basic system configuration. This type of information is stored in battery-backed CMOS RAM so that it retains the Setup information when the power is turned off. Entering Setup Power on the computer and press immediately. This will allow you to enter Setup. Standard CMOS Features Use this menu for basic system configuration. (Date, time, IDE, etc.
N e t w o r k Ap p l i a n c e FWS-816B Advanced Chipset Features Use this menu to change the values in the chipset registers and optimize your system performance. Integrated Peripherals Use this menu to specify your settings for integrated peripherals. (Primary slave, secondary slave, keyboard, mouse etc.) Power Management Setup Use this menu to specify your settings for power management. (HDD power down, power on by ring, KB wake up, etc.
N e t w o r k Ap p l i a n c e FWS-816B Load Optimized Defaults Use this menu to load the BIOS default values that are factory settings for optimal performance system operations. While AWARD has designated the custom BIOS to maximize performance, the factory has the right to change these defaults to meet their needs. Set Supervisor/User Password Use this menu to set Supervisor/User Passwords. Save and Exit Setup Save CMOS value changes to CMOS and exit setup.
N e t w o r k Ap p l i a n c e FWS-816B Chapter 4 Driver Installation Chapter 4 Driver Installation 4-1
N e t w o r k Ap p l i a n c e FWS-816B The FWS-816 Rev.B comes with an AutoRun CD-ROM that contains all drivers and utilities that can help you to install the driver automatically. Insert the driver CD, the driver CD-title will auto start and show the installation guide. If not, please follow the sequence below to install the drivers. Follow the sequence below to install the drivers: Step 1 – Install INF Driver Step 2 – Install VGA Driver Step 3 – Install LAN Driver USB 2.
N e t w o r k Ap p l i a n c e 4.1 FWS-816B Installation: Insert the FWS-816 Rev.B CD-ROM into the CD-ROM drive and install the drivers from Step 1 to Step 3 in order. Step 1 – Install INF Driver 1. Click on the Step 1-INF folder and select the OS you system is 2. Double click on the *.exe file located in each OS folder 3. Follow the instructions that the window shows 4. The system will help you install the driver automatically Step 2 – Install VGA Driver 1. Click on the Step 2 –VGA folder 2.
N e t w o r k Ap p l i a n c e FWS-816B 1. Click on the Step 3 –LAN folder and click on the folder of Intel 82573 Driver 2. Double click on Autorun 3. Follow the instructions that the window shows 4. The system will help you install the driver automatically Install the Intel 82551ER Driver 1. Click on Start button 2. Click on Settings button 3. Click on Control Panel button 4. Click on System button 5. Select Hardware and click on Device Manager… 6. Double click on Ethennet Controller 7.
N e t w o r k Ap p l i a n c e FWS-816B Appendix A Programming the Watchdog Timer Appendix A Programming the Watchdog Timer A-1
N e t w o r k Ap p l i a n c e FWS-816B A.1 Programming FWS-816 Rev.B utilizes W83627EHG chipset as its watchdog timer controller. Below are the procedures to complete its configuration and the AAEON intial watchdog timer program is also attached based on which you can develop customized program to fit your application.
N e t w o r k Ap p l i a n c e FWS-816B (2) Modify the data of configuration registers (3) Exit the W83627EHG config Mode. Undesired result may occur if the config Mode is not exited normally. (1) Enter the W83627EHG config Mode To enter the W83627EHG config Mode, two special I/O write operations are to be performed during Wait for Key state. To ensure the initial state of the key-check logic, it is necessary to perform two write operations to the Special Address port (2EH).
N e t w o r k Ap p l i a n c e FWS-816B = 01 Power LED pin is drived low. = 10 Power LED pin is a 1Hz toggle pulse with 50 duty cycle. = 11 Power LED pin is a 1/4Hz toggle pulse with 50 duty cycle. Bit 5-4 : Reserved Bit 3 : select WDTO count mode. Bit 2 =0 second =1 minute : Enable the rising edge of keyboard Reset (P20) to force Time-out event.
N e t w o r k Ap p l i a n c e FWS-816B second/minutes WatchDog Timer Register III (Index=F7h, Default=00h) Bit 7 Bit 6 : Mouse interrupt reset Enable or Disable =1 Watchdog Timer is reset upon a Mouse interrupt =0 Watchdog Timer is not affected by Mouse interrupt : Keyboard interrupt reset Enable or Disable =1 Watchdog Timer is reset upon a Keyboard interrupt =0 Watchdog Timer is not affected by Keyboard interrupt Bit 5 : Force Watchdog Timer Time-out.
N e t w o r k Ap p l i a n c e FWS-816B A.2 W83627EHG Watchdog Timer Initial Program Example: Setting 10 sec.
N e t w o r k Ap p l i a n c e FWS-816B ;/////////////////////////////////////////////////////////////////////////////////////////////// Dec dx Mov al,0f5h ;CRF5 (PLED mode register) Out dx,al Inc dx In al,dx And al,not 08h ;Set second as counting unit Out dx,al ;/////////////////////////////////////////////////////////////////////////////////////////////// Dec dx Mov al,0f6h ; CRF6 Out dx,al Inc dx Mov al,10 ;Set timeout interval as 10 sec.
N e t w o r k Ap p l i a n c e FWS-816B Appendix B I/O Information Appendix B I/O Information B-1
N e t w o r k Ap p l i a n c e B.
N e t w o r k Ap p l i a n c e FWS-816B B.
N e t w o r k Ap p l i a n c e B.3 IRQ Mapping Chart B.
N e t w o r k Ap p l i a n c e FWS-816B Appendix C Standard Firewall Platform Setting Appendix C Standard Firewall Platform Setting C-1
N e t w o r k Ap p l i a n c e FWS-816B C.
N e t w o r k Ap p l i a n c e FWS-816B C.
N e t w o r k Ap p l i a n c e FWS-816B out dx,al [RED LED BLINK] mov dx,48Fh ;( IO_PORT = 48Fh) in al,dx or al,00010000b ;set bit 4 -->high out dx,al mov dx,4B8h ;( IO_PORT = 4B8h) in al,dx and al,11110111b ;set bit 3 -->low out dx,al mov dx,49Bh ;( IO_PORT = 49Bh) in al,dx or al,00010000b ;set bit 4 -->high(control blink) out dx,al [GREEN LED ON] mov dx,48Fh ;( IO_PORT = 48Fh) in al,dx and al,11101111b ;set bit 4 -->low out dx,al mov dx,4B8h Appendix C Standard Firewall Platform Setting C-4
N e t w o r k Ap p l i a n c e FWS-816B in al,dx or al,00001000b ;set bit 3 -->high out dx,al [GRN LED BLINK] mov dx,48Fh ;( IO_PORT = 48Fh) in al,dx and al,11101111b ;set bit 4 -->low out dx,al mov dx,4B8h ;( IO_PORT = 4B8h) in al,dx or al,00001000b ;set bit 3 -->high out dx,al mov dx,49Bh ;( IO_PORT = 49Bh) in al,dx or al,00010000b ;set bit 4 -->high(control blink) out dx,al Appendix C Standard Firewall Platform Setting C-5
N e t w o r k Ap p l i a n c e FWS-816B C.
N e t w o r k Ap p l i a n c e FWS-816B [Watch Dog Mode] mov dx,48dh ;( IO_PORT = 48dh) in al,dx or al,01000000b ;set bit 7-->high out dx,al mov dx,48Fh ;( IO_PORT = 48Fh) in al,dx or al,00000100b ;set bit 2-->high out dx,al Appendix C Standard Firewall Platform Setting C-7
N e t w o r k Ap p l i a n c e C.
N e t w o r k Ap p l i a n c e FWS-816B } void Entry_mode_set() { outportb(0x378, 0x06); wait(); outportb(0x37A, 0xC8); wait(); outportb(0x37A, 0xCA); wait(); } void Display_Off() { outportb(0x378, 0x08); wait(); outportb(0x37A, 0xC8); wait(); outportb(0x37A, 0xCA); Appendix C Standard Firewall Platform Setting C-9
N e t w o r k Ap p l i a n c e wait(); } void Display_On_Cursor_Off() { outportb(0x378, 0x0C); wait(); outportb(0x37A, 0xC8); wait(); outportb(0x37A, 0xCA); wait(); } void Display_On_Cursor_On() { outportb(0x378, 0x0E); wait(); outportb(0x37A, 0xC8); wait(); Appendix C Standard Firewall Platform Setting C-10 FWS-816B
N e t w o r k Ap p l i a n c e FWS-816B outportb(0x37A, 0xCA); wait(); } /******************************************************************** ****/ // Set the interface data length. // Number of display line and character font. // For 5x7 dots and 2 lines display now.
N e t w o r k Ap p l i a n c e wait(); } void Write_Char( char x ) { outportb(0x378, x); outportb(0x37A, 0xC0); wait(); outportb(0x37A, 0xC2); wait(); } void Change_Line() { outportb(0x378, 0xC0); wait(); outportb(0x37A, 0xC8); wait(); outportb(0x37A, 0xCA); Appendix C Standard Firewall Platform Setting C-12 FWS-816B
N e t w o r k Ap p l i a n c e FWS-816B wait(); } void wait() { for (int i = 0 ; i < 0x10 ; i++) { for (int j = 0 ; j < 0x80 ; j++) { outportb(0x0EB, 0Xff); } } } Appendix C Standard Firewall Platform Setting C-13
N e t w o r k Ap p l i a n c e FWS-816B C.5 Console Redirection Console redirection allows you to maintain a system from a remote location by re-directing keyboard input and text output through the serial port. This section will tell you how to use the console redirection. 1. Please insert console cable between on FWS-816 Rev.B and remote client system. 2. Setup BIOS in FWS-816 Rev.B.
N e t w o r k Ap p l i a n c e FWS-816B Step4 - From the connect to pull-down menu, select a COM port available on your client system and click OK Step5 - Select Baud Rate >> 19200, Flow control >> None, Data bit >>8, Parity cheek >> None, Stop bit>>1 4. Power on FWS-816 Rev.B and it will display the BIOS information on the client system.
