SubCompact Board GENE-5315 GENE-5315 AMD® Geode LX800/900 series Processors RTL8139DL for 10/100Mbps Type II CompactFlash 2 COM (Rev.A), 5 COM (Rev.B) 4 USB2.0, 1 IrDA Type III Mini PCI GENE-5315 Manual Rev.A + B 4th Ed.
SubCompact Board GENE-5315 Copyright Notice This document is copyrighted, 2009. All rights are reserved. The original manufacturer reserves the right to make improvements to the products described in this manual at any time without notice. No part of this manual may be reproduced, copied, translated, or transmitted in any form or by any means without the prior written permission of the original manufacturer. Information provided in this manual is intended to be accurate and reliable.
SubCompact Board GENE-5315 Acknowledgments All other products’ name or trademarks are properties of their respective owners. Award is a trademark of Award Software International, Inc. CompactFlash™ is a trademark of the Compact Flash Association. AMD, the AMD Arrow logo and combinations thereof are trademarks of Advanced Micro Devices, Inc. ® Microsoft Windows is a registered trademark of Microsoft Corp. ITE is a trademark of Integrated Technology Express, Inc.
SubCompact Board GENE-5315 Packing List Before you begin installing your card, please make sure that the following materials have been shipped: • 1 9681531501 Cable Kit for GENE-5315 1700060192 Keyboard & Mouse Cable 1709100201 USB Cable 1701440500 IDE Cable 3.
SubCompact Board GENE-5315 Contents Chapter 1 General Information 1.1 Introduction................................................................ 1-2 1.2 Features .................................................................... 1-3 1.3 Specifications ............................................................ 1-4 Chapter 2 Quick Installation Guide 2.1 Safety Precautions .................................................... 2-2 2.2 Connectors, Jumpers and Mechanical Drawings...... 2-3 2.
SubCompact Board GENE-5315 2.17 USB Port #1 and Port #2 (CN5) .............................. 2-17 2.18 Digital I/O Connector (CN6) .................................... 2-17 2.19 Audio Input/Output/Cdin/MIC (CN7)........................ 2-18 2.20 ATX External 5VSB (CN8) ...................................... 2-18 2.21 4P Power Socket (CN9) .......................................... 2-19 2.22 LVDS Connector (CN10)......................................... 2-19 2.23 PC/104 (CN11) (For Rev.A only) ............
SubCompact Board GENE-5315 2.40 Compact Flash Disk Slot (CFD1) .......................... 2-29 2.41 Mini-PCI Slot (MPCI1) ........................................... 2-30 2.42 DDR SODIMM Slot (DIMM1) ................................. 2-30 Chapter 3 Award BIOS Setup 3.1 System Test and Initialization. .................................. 3-2 3.2 Award BIOS Setup .................................................... 3-3 Chapter 4 Driver Installation 4.1 Software Drivers.....................................
SubCompact Board GENE-5315 B.5 DMA Channel Assignments...................................B-3 Appendix C Mating Connector C.1 List of Mating Connectors and Cables..................
SubCompact Board GENE-5315 Chapter 1 General Information Chapter 1 General Information 1- 1
SubCompact Board GENE-5315 1.1 Introduction AAEON, a leading embedded boards manufacturer, is pleased to announce the debut of their new generation 3.5” SubCompact Board—GENE-5315. The GENE-5315 not only completes AAEON’s product line of Subcompact boards, but also balances performance and cost in the embedded market. GENE-5315 adopts optional onboard AMD Geode LX800 and LX900. The system memory is deployed with SODIMM DDR 333/400 up to 1GB.
SubCompact Board GENE-5315 1.2 Features Onboard AMD Geode LX 800/LX900 processors SODIMM DDR 333 Max. 1GB, DDR 400 Max. 512MB Up to 24-bit Single Channel LVDS TFT LCD Dual 10/100Mbps Ethernet Type III Mini-PCI and PC/104 (For Rev.A Only) Expansions IDE, Floppy Disk Drive & Compactflash Slot AC97 Codec 2 CH Audio COM, Parallel x 1, USB2.
SubCompact Board GENE-5315 1.3 Specifications System Processor Onboard AMD Geode LX800/ LX900 Series Processor System Memory 200-pin DDR SODIMM x 1, Max.
SubCompact Board Display GENE-5315 Supports CRT/LCD simultaneous display Chipset AMD LX series + TI SN75LVDS83 Memory Shared system memory up to 254 MB LCD Interface Up to 24-bit TTL/LVDS TFT LCD Resolution Up to 1920 x 1440 @ 24bpp for CRT Up to 1600 x 1200 @ 24bpp for LCD I/O Storage EIDE x 1 (UDMA-33 x 1); Floppy Disk Drive x 1; Type II CompactFlash x 1 Serial Port RS-232 x 1 (Rev.A)/ RS-232 x 4 & TTL UART x 1 (Rev.B), RS-232/422/485 x 1 Parallel Port SPP/EPP/ECP mode USB Port USB2.
SubCompact Board GENE-5315 Chapter 2 Quick Installation Guide Notice: The Quick Installation Guide is derived from Chapter 2 of user manual. For other chapters and further installation instructions, please refer to the user manual CD-ROM that came with the product. Part No.
SubCompact Board GENE-5315 2.1 Safety Precautions Always completely disconnect the power cord from your board whenever you are working on it. Do not make connections while the power is on, because a sudden rush of power can damage sensitive electronic components. Always ground yourself to remove any static charge before touching the board. Modern electronic devices are very sensitive to static electric charges. Use a grounding wrist strap at all times.
SubCompact Board GENE-5315 2.2 Jumpers, Connectors, and Mechanical Drawings GENE-5315 Rev.
SubCompact Board GENE-5315 34.84 Solder Side 132.84 DIMM1 66.04 52.59 CFD1 12.43 Chapter 2 Quick Installation Guide 2 - 4 0.00 30.49 0.
SubCompact Board GENE-5315 Mechanical Drawings 91.93 95.20 98.38 53.28 26.62 18.67 0.00 0.63 5.13 9.42 82.66 85.76 HEATSINK HEIGHT (13.20) (12.55) 131.95 125.81 11.41 120.27 78.73 (103.50) (77.67) 85.33 29.17 0.60 86.12 86.17 (122.55) 91.07 91.73 92.07 87.14 88.21 97.98 106.68 27.87 14.55 108.27 119.27 (46.99) 123.73 87.67 133.93 132.56 125.56 (22.22) 137.16 133.93 132.27 (13.00) 61.13 53.95 50.09 12.39 38.11 18.84 8.42 13.34 37.73 47.18 38.31 68.34 50.46 19.
SubCompact Board GENE-5315 GENE-5315 Rev.
SubCompact Board GENE-5315 34.84 Solder Side 132.84 DIMM1 66.04 52.53 CFD1 12.43 0.00 0.00 30.49 98.38 8.
SubCompact Board GENE-5315 (12.55) (46.99) 11.47 87.67 131.95 123.73 120.27 (22.22) 137.16 133.93 132.22 125.75 133.93 125.56 HEATSINK HEIGHT (13.20) 95.20 98.37 82.66 85.76 53.28 3.23 0.00 0.60 5.13 9.41 18.67 26.62 Mechanical Drawings 114.94 (77.67) 106.60 91.07 91.73 86.12 85.33 27.37 11.81 (13.00) 61.13 59.49 8.59 50.46 (122.55) 85.92 84.27 (103.50) 96.71 92.07 47.18 37.85 13.34 68.34 33.66 14.61 10.77 1.02 1.52 0.00 4.06 6.86 7.41 5.84 5.01 4.56 0.00 6.10 8.
SubCompact Board GENE-5315 2.3 List of Jumpers The board has a number of jumpers that allow you to configure your system to suit your application. The table below shows the function of each of the board's jumpers: Label Function JP1 AT/ATX Power Type Selection JP2 CFD Master/Slave Selection JP3 Clear CMOS JP4 LCD Clock and LVDS Operating Voltage Selection JP5 COM Ports RI/+5V/+12V Selection JP6 Inverter Voltage Selection JP7 CFD Voltage Selection (For Rev.
SubCompact Board GENE-5315 2.4 List of Connectors The board has a number of connectors that allow you to configure your system to suit your application. The table below shows the function of each of the board’s connectors: Note: For further information about mating connectors, please refer to the appendix of the manual.
SubCompact Board GENE-5315 CN18 Mini-Din PS/2 CN19 Serial Port #1 CN20 CRT Display CN21 USB Port #3 and Port #4 CN22 LCD Inverter Voltage CN23 Serial Port #3 (For Rev. B only) CN24 Serial Port #5 (For Rev. B only) CN25 Serial Port #4 (For Rev. B only) CN26 Serial Port #6 (TTL/GPS) (For Rev.
SubCompact Board GENE-5315 2.5 Setting Jumpers You configure your card to match the needs of your application by setting jumpers. A jumper is the simplest kind of electric switch. It consists of two metal pins and a small metal clip (often protected by a plastic cover) that slides over the pins to connect them. To “close” a jumper you connect the pins with the clip. To “open” a jumper you remove the clip. Sometimes a jumper will have three pins, labeled 1, 2 and 3.
SubCompact Board GENE-5315 2.6 AT/ATX Power Type Selection (JP1) JP1 Function 1-2 ATX Power Supply AT Power Supply (Default) 2.7 CFD Master/Slave Selection (JP2) JP2 Function 1-2 Slave 2-3 Master (Default) 2.8 Clear CMOS (JP3) JP3 Function 1-2 Normal (Default) 2-3 Clear CMOS 2.9 LCD Clock and LVDS Operating Voltage Selection (JP4) Clock JP4 Function 1-3 Normal (Default) 3-5 Shift Clock LVDS Operating Voltage JP4 Function 2-4 +5V 4-6 +3.
SubCompact Board GENE-5315 2.10 COM Ports RI/+5V/+12V Selection (JP5) COM 1 JP5 Function 1-2 +12V 3-4 +5V 5-6 RI (Default) COM 2 JP5 Function 7-8 +12V 9-10 +5V 11-12 RI (Default) 2.11 Inverter Voltage Selection (JP6) JP6 Function 1-2 +5V (Default) 2-3 +12V 2.12 CFD Voltage Selection (JP7) (For Rev. B only) JP7 Function 1-2 +5V (Default) 2-3 +3.3V 2.
SubCompact Board GENE-5315 5 D6 6 D9 7 D5 8 D10 9 D4 10 D11 11 D3 12 D12 13 D2 14 D13 15 D1 16 D14 17 D0 18 D15 19 Ground 20 N.C. 21 DREQ 22 Ground 23 IOW# 24 Ground 25 IOR# 26 Ground 27 IORDY 28 Ground 29 DACK# 30 Ground 31 IRQ14 32 N.C. 33 DA1 34 PDIAG# 35 DA0 36 DA2 37 CS#1 38 CS#3 39 Active LED# 40 Ground 41 +5Volt. 42 +5Volt. 43 Ground 44 N.C.
SubCompact Board GENE-5315 7 Ground 8 INDEX# 9 Ground 10 MTRA# 11 Ground 12 DRVB# 13 Ground 14 DRVA# 15 Ground 16 MTRB# 17 Ground 18 DIR# 19 Ground 20 STEP# 21 Ground 22 WDATA# 23 Ground 24 WGATE# 25 Ground 26 TRK0# 27 Ground 28 WPT# 29 N.C. 30 RDATA# 31 Ground 32 HDSEL# 33 N.C. 34 DSKCHG# 2.
SubCompact Board 25 GENE-5315 SLCT 26 N.C. 2.16 Front Panel Connector (CN4) Pin Signal Pin Signal 1 Power On Button (-) 2 Power On Button (+) 3 IDE LED (-) 4 IDE LED (+) 5 External Buzzer (-) 6 External Buzzer (+) 7 Power LED (-) 8 Power LED (+) 9 Reset Switch (-) 10 Reset Switch (+) 2.17 USB Port #1 and Port #2 (CN5) Pin Signal Pin Signal 1 VDD 2 Ground 3 D0- 4 Ground 5 D0+ 6 D1+ 7 Ground 8 D1- 9 Ground 10 VDD 2.
SubCompact Board GENE-5315 DIO-2 CN6 Pin 2 Bit 6 U1 Pin 21 (GPIO 26) DIO-3 CN6 Pin 3 Bit 5 U1 Pin 22 (GPIO 25) DIO-4 CN6 Pin 4 Bit 4 U1 Pin 23 (GPIO 24) DIO-5 CN6 Pin 5 Bit 3 U1 Pin 24 (GPIO 23) DIO-6 CN6 Pin 6 Bit 2 U1 Pin 25 (GPIO 22) DIO-7 CN6 Pin 7 Bit 1 U1 Pin 26 (GPIO 21) DIO-8 CN6 Pin 8 Bit 0 U1 Pin 27 (GPIO 20) 2.
SubCompact Board 6 GENE-5315 +5 Volt. Standby 2.21 4P Power Socket (CN9) Pin Signal 1 +12 Volt. 2 Ground 3 Ground 4 +5 Volt. 2.22 LVDS LCD Connector (CN10) Pin Signal Pin Signal 1 N.C. 2 N.C. 3 VDD 4 Ground 5 CLK- 6 CLK+ 7 VDD 8 Ground 9 D0- 10 D0+ 11 D1- 12 D1+ 13 D2- 14 D2+ 15 D3- 16 D3+ 17 N.C. 18 N.C. 19 N.C. 20 N.C. 21 N.C. 22 N.C. 23 N.C. 24 N.C. 25 N.C. 26 N.C. 27 VDD 28 Ground 29 N.C. 30 N.C.
SubCompact Board GENE-5315 2.23 PC/104 (CN11) (For Rev.
SubCompact Board GENE-5315 29 A2 +5V 30 A1 OSC 31 A0 GND 32 GND GND Pin D C 1 GND GND 2 MEMCS16* SBHE* 3 IOCS16* LA23 4 IRQ10 LA22 5 IRQ11 LA21 6 IRQ12 LA20 7 IRQ15 LA19 8 IRQ14 LA18 9 DACK0* LA17 10 DRQ0 MEMR* 11 DACK5* MEMW* 12 DRQ5 SD8 J2/P2 13 DACK6* SD9 14 DRQ6 SD10 15 DACK7* SD11 16 DRQ7 SD12 17 +5V SD13 18 MASTER* SD14 19 GND SD15 20 GND GND/KEY Note 1: GENE-5315 does not support PC/104 way legacy ISA-DMA mode caused by AMD ar
SubCompact Board GENE-5315 Geode’s architecture limitation. The following steps for setup the resources manually for your reference. 1. Retrieve the resource of the PC/104 card. The information is typically contained in the manual of the PC/104 card. 2. Push a function key “Delete” to get into the BIOS. 3. Enable the resource of the device in BIOS setup. 4. Disable the resource of the device for which conflicts the resource of the device mentioned above in BIOS setup. 5.
SubCompact Board GENE-5315 25 R0 26 R1 27 R2 28 R3 29 R4 30 R5 31 R6 32 R7 33 Ground 34 Ground 35 Clock 36 VSYNC 37 DE 38 HSYNC 39 N.C. 40 N.C. For 18-bit TFT LCD Pin Signal Pin Signal 1 +5Volt. 2 +5Volt. 3 Ground 4 Ground 5 +3.3Volt. 6 +3.3Volt. 7 N.C. 8 Ground 9 N.C. 10 N.C. 11 B0 12 B1 13 B2 14 B3 15 B4 16 B5 17 N/C 18 N/C 19 G0 20 G1 21 G2 22 G3 23 G4 24 G5 25 N.C. 26 N.C.
SubCompact Board GENE-5315 37 DE 38 HSYNC 39 N.C. 40 N.C. COM2/ RS-232 Mode Pin Signal Pin Signal 1 DCDB 2 RXB 3 TXB 4 DTRB 5 Ground 6 DSRB 7 RTSB 8 CTSB 9 RIB (+5V/ +12V) 10 N.C. COM2/ RS-422 Mode Pin Signal Pin Signal 1 TXD- 2 RXD+ 3 TXD+ 4 RXD- 5 Ground 6 N.C. 7 N.C. 8 N.C. 9 N.C. 10 N.C. COM2/ RS-485 Mode Pin Signal Pin Signal 1 TXD- 2 N.C. 3 TXD+ 4 N.C. 5 Ground 6 N.C. 7 N.C. 8 N.C. 9 N.C. 10 N.C. 2.
SubCompact Board 2 +5 Volt. 3 Ground GENE-5315 2.27 Ethernet 10/100 Base-TX RJ-45 Phone Jack #1 (CN15) Pin Signal Pin Signal 1 RXD- 2 RXD+ 3 RCT 4 N.C. 5 N.C. 6 TCT 7 TXD- 8 TXD+ 9 ACT_LED 10 LINK_LED 11 +3.3 Volt. 12 SPD_LED 13 Ground 14 Ground 2.28 Ethernet 10/100 Base-TX RJ-45 Phone Jack #2 (CN16) Pin Signal Pin Signal 1 RXD- 2 RXD+ 3 RCT 4 N.C. 5 N.C. 6 TCT 7 TXD- 8 TXD+ 9 ACT_LED 10 LINK_LED 11 +3.3 Volt.
SubCompact Board 4 Ground 5 TX 6 CIR_RX (Option) GENE-5315 2.30 Mini-DIN PS/2 Keyboard/ Mouse Connector (CN18) Pin Signal Pin Signal 1 Keyboard Data 2 Keyboard Data 3 Ground 4 Ground 5 +5 Volt. 6 +5 Volt. 7 Shield 8 Shield 2.31 Serial Port #1 Connector (CN19) COM 1 Pin Signal Pin Signal 1 DCDA 2 RXA 3 TXA 4 DTRA 5 Ground 6 DSRA 7 RTSA 8 CTSA 9 RIA (+5V/ +12V) 10 N.C. 2.32 CRT Display Connector (CN20) Pin Signal Pin Signal 1 RED 9 +5 Volt.
SubCompact Board 8 GENE-5315 Ground 2.33 USB Port #3 and Port #4 (CN21) Pin Signal Pin Signal 1 VDD 2 Ground 3 D2- 4 Ground 5 D2+ 6 D3+ 7 Ground 8 D3- 9 Ground 10 VDD 2.34 LCD Inverter Voltage (CN22) Pin Signal 1 VCC 2 Backlight Control 3 Ground 4 Ground 5 Enable 2.35 Serial Port #3 (CN23) (For Rev.B only) COM 3 Pin Signal Pin Signal 1 DCD3 2 RX3 3 TX3 4 DTR3 5 Ground 6 DSR3 7 RTS3 8 CTS3 9 RI3 10 N.C.
SubCompact Board GENE-5315 2.36 Serial Port #5 (CN24) (For Rev.B only) COM 5 Pin Signal Pin Signal 1 DCD5 2 RX5 3 TX5 4 DTR5 5 Ground 6 DSR5 7 RTS5 8 CTS5 9 RI5 10 N.C. Note: An APM Mode limitation, OS (Operating System) recognizes serial port 5 & 6 of GENE-5315 Rev.B but is reverse. OS will reassign IRQ and give sequence of serial port 5 & 6 after uninstalling all of serial ports and second time boots in OS. 2.37 Serial Port #4 (CN25) (For Rev.
SubCompact Board GENE-5315 Note: An APM Mode limitation, OS (Operating System) recognizes serial port 5 & 6 of GENE-5315 Rev.B but is reverse. OS will reassign IRQ and give sequence of serial port 5 & 6 after uninstalling all of serial ports and second time boots in OS. 2.39 External Battery (BAT1) Pin Signal 1 VBAT (+3 Volt.) 2 Ground 2.
SubCompact Board GENE-5315 19 DA1 44 DACK# 20 DA0 45 DASP# 21 D0 46 PDIAG# 22 D1 47 D8 23 D2 48 D9 24 IO16# 49 D10 25 Ground 50 Ground 2.41 Mini-PCI Slot (MPCI1) Standard Specification 2.42 DDR SODIMM Slot (DIMM1) Standard SODIMM Slot Note from AMD: Memory configurations supported. Only one DIMM or SODIMM is supported as long as the configuration requirements are met.
SubCompact Board GENE-5315 Below Table for China RoHS Requirements 产品中有毒有害物质或元素名称及含量 AAEON Main Board/ Daughter Board/ Backplane 有毒有害物质或元素 部件名称 铅 汞 镉 六价铬 多溴联苯 多溴二苯醚 (Pb) (Hg) (Cd) (Cr(VI)) (PBB) (PBDE) × ○ ○ ○ ○ ○ × ○ ○ ○ ○ ○ 印刷电路板 及其电子组件 外部信号 连接器及线材 O：表示该有毒有害物质在该部件所有均质材料中的含量均在 SJ/T 11363-2006 标准规定的限量要求以下。 X：表示该有毒有害物质至少在该部件的某一均质材料中的含量超出 SJ/T 11363-2006 标准规定的限量要求。 备注：此产品所标示之环保使用期限，系指在一般正常使用状况下。 Chapter 2 Quick Installation Guide 2 - 31
SubCompact Board GENE-5315 Chapter 3 Award BIOS Setup Chapter 3 Award BIOS Setup 3-1
SubCompact Board 3.1 GENE-5315 System Test and Initialization These routines test and initialize board hardware. If the routines encounter an error during the tests, you will either hear a few short beeps or see an error message on the screen. There are two kinds of errors: fatal and non-fatal. The system can usually continue the boot up sequence with non-fatal errors.
SubCompact Board 3.2 GENE-5315 Award BIOS Setup Awards BIOS ROM has a built-in Setup program that allows users to modify the basic system configuration. This type of information is stored in battery-backed CMOS RAM so that it retains the Setup information when the power is turned off. Entering Setup Power on the computer and press immediately. This will allow you to enter Setup. Standard CMOS Features Use this menu for basic system configuration. (Date, time, IDE, etc.
SubCompact Board GENE-5315 Advanced Chipset Features Use this menu to change the values in the chipset registers and optimize your system performance. Integrated Peripherals Use this menu to specify your settings for integrated peripherals. (Primary slave, secondary slave, keyboard, mouse etc.) Power Management Setup Use this menu to specify your settings for power management. (HDD power down, power on by ring, KB wake up, etc.) PnP/PCI Configurations This entry appears if your system supports PnP/PCI.
SubCompact Board GENE-5315 Load Optimized Defaults Use this menu to load the BIOS default values that are factory settings for optimal performance system operations. While AWARD has designated the custom BIOS to maximize performance, the factory has the right to change these defaults to meet their needs. Set Supervisor/User Password Use this menu to set Supervisor/User Passwords. Save and Exit Setup Save CMOS value changes to CMOS and exit setup.
SubCompact Board GENE-5315 Chapter 4 Driver Installation Chapter 4 Driver Installation 4 - 1
SubCompact Board GENE-5315 4.1 Software Drivers This chapter describes the operation and installation of the display drivers supplied on the Supporting CD-ROM that are shipped with your product. The onboard VGA adapter is based on the AMD LX VGA Flat Panel/CRT controller. This controller offers a large set of extended functions and higher resolutions. The purpose of the enclosed software drivers is to take advantage of the extended features of the AMD LX VGA Flat Panel/CRT controller.
SubCompact Board GENE-5315 4.2 Necessary to Know The instructions in this manual assume that you understand elementary concepts of MS-DOS and the IBM Personal Computer.
SubCompact Board GENE-5315 4.3 Installing VGA Driver Win XP / Win XPe VGA Place the Driver CD-ROM into your CD-ROM drive and follow the steps below to install. 1. Click on Start button. 2. Click on Settings button. 3. Click on Control Panel button. 4. Click on System button. 5. Select Hardware and click on Device Manager…. 6. Double click on Video Controller (VGA Compatible). 7. Click on Update Driver…. 8. Click on Next. 9. Select Search for a suitable driver…, then click on Next. 10.
SubCompact Board GENE-5315 4.4 Installing AES Driver Win XP / Win XPe AES Place the Driver CD-ROM into your CD-ROM drive and follow the steps below to install. 1. Click on Start button. 2. Click on Settings button. 3. Click on Control Panel button. 4. Click on System button. 5. Select Hardware and click on Device Manager…. 6. Double click on Entertainment Encryption/Decryption Controller. 7. Click on Update Driver…. 8. Click on Next. 9. Select Search for a suitable driver…, then click on Next. 10.
SubCompact Board GENE-5315 4.5 Installing PCI to ISA Bridge Driver (For Rev.A only) Win XP / Win XPe System Place the Driver CD-ROM into your CD-ROM drive and follow the following steps to install. 1. Click on Start button. 2. Click on Settings button. 3. Click on Control Panel button. 4. Click on System button. 5. Select Hardware and click on Device Manager…. 6. Double click on Other PCI Bridge Device 7. Click on Update Driver…. 8. Click on Next. 9.
SubCompact Board GENE-5315 4.6 Installing Ethernet Driver 1. Click on the Step 4 – Lan folder. 2. Double click on the Setup file located in the folder. 3. Follow the instructions that the window shows. 4. The system will help you install the driver automatically. 4.7 Ethernet Software Configuration The onboard Ethernet interface supports all major network operating systems. I/O addresses and interrupts are easily configured via the Insyde BIOS Setup.
SubCompact Board GENE-5315 information. 4. After you have made your selections and the configuration is what you want, press . A prompt will appear asking if you want to save the configuration. Press "Y" if you want to save. There are three very useful diagnostic functions offered in the Ethernet Setup Menu as follows: 1. Run EEPROM test 2. Run Diagnostics on Board 3.
SubCompact Board GENE-5315 8. Click on Next. 9. Select Search for a suitable driver…, then click on Next. 10. Select Specify a location, then click on Next. 11. Click on Browse. 12. Select “LXWDMAu” file from CD-ROM (Drivers/Step 5 – Audio) then click on Open. 13. Double click on the “bin” folder 14. Click on OK. 15. Click on Next. 16. Click on Yes. 17. Click on Finish.
SubCompact Board GENE-5315 Appendix A Programming the Watchdog Timer Appendix A Programming the Watchdog Timer A - 1
SubCompact Board GENE-5315 A.1 Programming GENE-5315 utilizes ITE 8712 chipset as its watchdog timer controller. ( K version ) Below are the procedures to complete its configuration and the AAEON intial watchdog timer program is also attached based on which you can develop customized program to fit your application. Configuring Sequence Description After the hardware reset or power-on reset, the ITE 8712 enters the normal mode with all logical devices disabled except KBC.
SubCompact Board GENE-5315 There are three steps to complete the configuration setup: (1) Enter the MB PnP Mode; (2) Modify the data of configuration registers; (3) Exit the MB PnP Mode. Undesired result may occur if the MB PnP Mode is not exited normally. (1) Enter the MB PnP Mode To enter the MB PnP Mode, four special I/O write operations are to be performed during Wait for Key state.
SubCompact Board GENE-5315 Configure Control (Index=02h) This register is write only. Its values are not sticky; that is to say, a hardware reset will automatically clear the bits, and does not require the software to clear them. Bit 7-2 1 0 Description Reserved Returns to the Wait for Key state. This bit is used when the configuration sequence is completed. Resets all logical devices and restores configuration registers to their power-on states.
SubCompact Board 4 3 GENE-5315 WDT output through PWROK1/PWROK2 (pulse) enable Select the interrupt levelnote for WDT WatchDog Timer Time-out Value (LSB) Register (Index=73h, Default=00h) Bit 7-0 Description WDT Time-out value 7-0 WatchDog Timer Time-out Value (MSB) Register (Index=74h, Default=00h) Bit 7-0 Description WDT Time-out value 15-8 A.2 ITE8712 Watchdog Timer Initial Program .MODEL SMALL .
SubCompact Board GENE-5315 Watch_Dog_Setting: ;Timer setting mov al, cl mov cl, 73h call Superio_Set_Reg ;Clear by keyboard or mouse interrupt mov al, 0f0h mov cl, 71h call Superio_Set_Reg ;unit is second.
SubCompact Board GENE-5315 MOV DX,02Eh MOV CX,04h Init_1: MOV AL,BYTE PTR CS:[SI] OUT DX,AL INC SI LOOP Init_1 RET Enter_Configuration_Mode ENDP Exit_Configuration_Mode PROC NEAR MOV AX,0202h CALL Write_Configuration_Data RET Exit_Configuration_Mode ENDP Check_Chip PROC NEAR MOV AL,20h CALL Read_Configuration_Data CMP AL,87h JNE Not_Initial MOV AL,21h CALL Read_Configuration_Data Appendix A Programming the Watchdog Timer A - 7
SubCompact Board GENE-5315 CMP AL,12h JNE Not_Initial Need_Initial: STC RET Not_Initial: CLC RET Check_Chip ENDP Read_Configuration_Data PROC NEAR MOV DX,WORD PTR CS:[Cfg_Port+04h] OUT DX,AL MOV DX,WORD PTR CS:[Cfg_Port+06h] IN AL,DX RET Read_Configuration_Data ENDP Write_Configuration_Data PROC NEAR MOV DX,WORD PTR CS:[Cfg_Port+04h] OUT DX,AL XCHG AL,AH MOV DX,WORD PTR CS:[Cfg_Port+06h] OUT DX,AL RET Appendix A Programming the Watchdog Timer A - 8
SubCompact Board GENE-5315 Write_Configuration_Data ENDP Superio_Set_Reg proc near push ax MOV DX,WORD PTR CS:[Cfg_Port+04h] mov al,cl out dx,al pop ax inc dx out dx,al ret Superio_Set_Reg endp.
SubCompact Board GENE-5315 Cfg_Port DB 087h,001h,055h,055h DW 02Eh,02Fh END Main Note: Interrupt level mapping 0Fh-Dh: not valid 0Ch: IRQ12 . .
SubCompact Board GENE-5315 Appendix B I/O Information Appendix B I/O Information B - 1
SubCompact Board GENE-5315 B.
SubCompact Board GENE-5315 B.3 IRQ Mapping Chart for Rev.A IRQ0 System Timer IRQ1 Keyboard IRQ2 IRQ3 IRQ4 IRQ5 IRQ6 IRQ7 Cascade to IRQ Controller COM2 COM1 Unused Floppy Printer IRQ8 System CMOS / Real time clock IRQ9 Microsoft ACPI – Compliant system IRQ10 Unused IRQ11 Unused IRQ12 PS/2 mouse IRQ13 FPU IRQ14 Primary IDE IRQ15 Reserved B.4 IRQ Mapping Chart for Rev.
SubCompact Board GENE-5315 Appendix C Mating Connector Appendix C Mating Connector C - 1
SubCompact Board GENE-5315 C.1 List of Mating Connectors and Cables The table notes mating connectors and available cables.
SubCompact Board CN14 CN15 CN16 CN17 CN18 CN19 CN20 CN21 CN22 CN23 (Rev.B) CN24 (Rev.B) CN25 (Rev.B) CN26 (Rev.B) GENE-5315 System FAN Connector Ethernet Connector Ethernet Connector IrDA Connector Mini-Din PS/2 Connector Hobase 2503-H-3 Technology Neltron 7001-8P8C N/A Neltron 7001-8P8C N/A Neltron 2026A-06 N/A Serial Port 1 Connector CRT Display Connector USB Connector AMP Catch MD06F011 Electronics 121 707-09F Hobase 708HD-15M Technology Neltron 2026B-10 LCD Inverter Catch 2.
