SubCompact Board GENE-LN05 Rev.B GENE-LN05 Rev.B ® Intel Atom™N455/D525 Processors Intel ® 82567V & 82583V for 10/100/1000Mbps 2 SATA 3.0 Gb/s, 1 CompactFlash™ 6 COM, 7 USB2.0, Digital I/O 1 Mini Card/ SMBus/ LPC GENE-LN05 Manual Rev.B 3rd Ed.
SubCompact Board GENE-LN05 Rev.B Copyright Notice This document is copyrighted, 2011. All rights are reserved. The original manufacturer reserves the right to make improvements to the products described in this manual at any time without notice. No part of this manual may be reproduced, copied, translated, or transmitted in any form or by any means without the prior written permission of the original manufacturer. Information provided in this manual is intended to be accurate and reliable.
SubCompact Board GENE-LN05 Rev.B Acknowledgments All other products’ name or trademarks are properties of their respective owners. AMI is a trademark of American Megatrends Inc. CompactFlash™ is a trademark of the Compact Flash Association. Intel®, Atom are trademarks of Intel® Corporation. Microsoft Windows is a registered trademark of Microsoft Corp. ITE is a trademark of Integrated Technology Express, Inc.
SubCompact Board GENE-LN05 Rev.B Packing List Before you begin installing your card, please make sure that the following materials have been shipped: CD-ROM for manual (in PDF format) and drivers GENE-LN05 Rev.B with Active Cooler (D525 Version) or with Passive Cooler (N455 Version) If any of these items should be missing or damaged, please contact your distributor or sales representative immediately.
SubCompact Board GENE-LN05 Rev.B Contents Chapter 1 General Information 1.1 Introduction................................................................ 1-2 1.2 Features .................................................................... 1-3 1.3 Specifications ............................................................ 1-4 Chapter 2 Quick Installation Guide 2.1 Safety Precautions .................................................... 2-2 2.2 Location of Connectors & Jumpers ...........................
SubCompact Board GENE-LN05 Rev.B 2.18 SATA Port #2 (CN5)................................................ 2-13 2.19 SATA Port #1 (CN6)................................................ 2-13 2.20 LPC Expansion I/F (CN7)........................................ 2-14 2.21 External +5V Input –depends on the power input configuration (CN8) ......................................................... 2-14 2.22 External +12V Input-depends on the power input configuration (CN9) ..........................................
SubCompact Board GENE-LN05 Rev.B 2.41 LVDS Inverter Connector (CN28) ........................... 2-22 2.42 LVDS Output (CN29)............................................... 2-22 2.43 USB Port 1 & 2 (CN30) ........................................... 2-23 2.44 PS/2 Keyboard & Mouse (CN31) ............................ 2-23 2.45 COM Port #1 (CN32)............................................... 2-23 2.46 CRT Display Connector (CN33).............................. 2-23 2.47 SIM Card Socket (CN34) ...............
SubCompact Board GENE-LN05 Rev.B Appendix C Mating Connector C.1 List of Mating Connectors and Cables..................
SubCompact Board GENE-LN05 Rev.
SubCompact Board GENE-LN05 Rev.B 1.1 Introduction AAEON, a leading embedded boards manufacturer, is pleased to announce a new 3.5” SubCompact Board—GENE-LN05 Rev.B. The GENE-LN05 Rev.B is a cutting-edge product that provides high performance and low power consumption in the embedded market. GENE-LN05 Rev.B adopts the latest Intel® Atom processors and the system memory is deployed with SODIMM DDR3 up to 4 GB (D525 is up to 4 GB, N455 is up to 2 GB).
SubCompact Board GENE-LN05 Rev.B 1.2 Features Intel® Atom N455/D525 Processors Up To 1.8 GHz Intel® ICH8M DDR3 800 SODIMM, Max. 4 GB for D525; Max. 2 GB for N455 Gigabit Ethernet x 2 CRT, 18/24-bit Single Channel LVDS LCD 2CH HD Audio SATA 3.0Gb/s x 2 (Optional RAID 0 & 1), CompactFlash™ x1 USB 2.
SubCompact Board GENE-LN05 Rev.B 1.3 Specifications System Processor Intel® Atom™ N455/D525 1.8GHz Processors System Memory 204-pin DDR3 800 SODIMM x 1, Max. 4 GB for Intel® Atom™ D525; Max.
SubCompact Board GENE-LN05 Rev.B Board Size 5.75”(L) x 4”(W) (146mm x 101.6mm) Gross Weight 0.88 lb (0.
SubCompact Board GENE-LN05 Rev.B RS-232/422/485 (auto flow) x 1 (AAEON recommends for the Serial Port to be at the 9600 baud rate during high temperature operation.) Parallel Port SPP/EPP/ECP x 1 USB Port USB2.
SubCompact Board GENE-LN05 Rev.
SubCompact Board GENE-LN05 Rev.B 2.1 Safety Precautions Always completely disconnect the power cord from your board whenever you are working on it. Do not make connections while the power is on, because a sudden rush of power can damage sensitive electronic components. Always ground yourself to remove any static charge before touching the board. Modern electronic devices are very sensitive to static electric charges. Use a grounding wrist strap at all times.
SubCompact Board GENE-LN05 Rev.B 2.
SubCompact Board Solder Side Chapter 2 Quick Installation Guide 2-4 GENE-LN05 Rev.
SubCompact Board GENE-LN05 Rev.B 2.
SubCompact Board Solder Side Chapter 2 Quick Installation Guide 2-6 GENE-LN05 Rev.
SubCompact Board GENE-LN05 Rev.B 2.4 List of Jumpers The board has a number of jumpers that allow you to configure your system to suit your application.
SubCompact Board GENE-LN05 Rev.B 2.5 List of Connectors The board has a number of connectors that allow you to configure your system to suit your application.
SubCompact Board GENE-LN05 Rev.
SubCompact Board GENE-LN05 Rev.B 2.6 Setting Jumpers You configure your card to match the needs of your application by setting jumpers. A jumper is the simplest kind of electric switch. It consists of two metal pins and a small metal clip (often protected by a plastic cover) that slides over the pins to connect them. To “close” a jumper you connect the pins with the clip. To “open” a jumper you remove the clip. Sometimes a jumper will have three pins, labeled 1, 2 and 3.
SubCompact Board GENE-LN05 Rev.B 2.7 Touch Screen 4/5/8-wire Mode Selection (JP1) JP1 Function 1-2 Closed 4/8-wire (Default) 1-2 Open 5-wire 2.8 Auto Power Button Selection (JP2) JP2 Function 1-2 Enable (Default) 2-3 Disable 2.9 COM2 RI/+5V/+12V Selection (JP3) JP3 Function 1-2 +12V 3-4 +5V 5-6 RI (Default) 2.10 Clear CMOS (JP4) JP4 Function 1-2 Normal (Default) 2-3 Clear CMOS 2.
SubCompact Board GENE-LN05 Rev.B 2.12 LVDS Operating Voltage Selection (JP6) JP6 Function 1-2 +5V 2-3 +3.3V (Default) 2.13 LVDS Inverter Voltage Selection (JP7) JP7 Function 1-2 +12V 2-3 +5V (Default) 2.14 2-Pin ATX Power Connector (CN1) (Optional) Pin Signal 1 +12V 2 Ground 2.15 CPU FAN Connector (CN2) Pin Signal 1 Ground 2 +5V (Optional) / +12V 3 FAN Sense 2.
SubCompact Board 5 PSON# 6 +5 Volt. Standby GENE-LN05 Rev.B 2.17 External +5VSB Input (CN4) Pin Signal 1 PSON# 2 Ground 3 +5V Standby 2.18 SATA Port # 2 (CN5) Pin Signal 1 Ground 2 TX1+ 3 TX1- 4 Ground 5 RX1- 6 RX1+ 7 Ground 2.
SubCompact Board GENE-LN05 Rev.B 2.20 LPC Expansion I/F (CN7) Pin Signal 1 LAD0 2 LAD1 3 LAD2 4 LAD3 5 +3.3 Volt. 6 LFRAME# 7 LRESET# 8 Ground 9 LPC_CLK 10 LDRQ#0 11 LDRQ#1 12 SERIRQ 2.21 External +5V Input –depends on the power input configuration (CN8) DC Terminal Pin Signal 1 Ground 2 +5V 2.
SubCompact Board GENE-LN05 Rev.B 2.23 Touch Screen Connector (CN10) Pin 8-wire 5-wire 4-wire 1 Ground Ground Ground 2 Top Excite UL(Y) Top 3 Bottom Excite UR(H) Bottom 4 Left Excite LL(L) Left 5 Right Excite LR(X) Right 6 Top Sense SENSE N/C 7 Bottom Sense N/C N/C 8 Left Sense N/C N/C 9 Right Sense N/C N/C 2.24 +5V Output For SATA HDD (CN11) Pin Signal 1 +5V (800mA) 2 Ground 2.
SubCompact Board GENE-LN05 Rev.B 3 RXF 4 RTSF 5 TXF 6 CTSF 7 DTRF 8 RIF 9 Ground 10 N/C 2.27 USB Port #7 (CN14) Pin Signal 1 +5V Standby 2 Data6- 3 Data6+ 4 Ground 5 Ground 2.28 COM Port #5 (CN15) Pin Signal Pin Signal 1 DCDE 2 DSRE 3 RXE 4 RTSE 5 TXE 6 CTSE 7 DTRE 8 RIE 9 Ground 10 N/C 2.
SubCompact Board GENE-LN05 Rev.B 2.30 USB Port #5 (CN17) Pin Signal 1 +5V Standby 2 Data4- 3 Data4+ 4 Ground 5 Ground 2.31 COM Port #4 (CN18) Pin Signal Pin Signal 1 DCDD 2 DSRD 3 RXD 4 RTSD 5 TXD 6 CTSD 7 DTRD 8 RID 9 Ground 10 N/C 2.32 USB Port #4 (CN19) Pin Signal 1 +5V Standby 2 Data3- 3 Data3+ 4 Ground 5 Ground 2.
SubCompact Board 3 Data2+ 4 Ground 5 Ground GENE-LN05 Rev.B 2.34 COM Port #3 (CN21) Pin Signal Pin Signal 1 DCDC 2 DSRC 3 RXC 4 RTSC 5 TXC 6 CTSC 7 DTRC 8 RIC 9 Ground 10 N/C 2.
SubCompact Board GENE-LN05 Rev.B RS-485 Mode Pin Signal Pin Signal 1 TXD- 2 N/C 3 N/C 4 N/C 5 TXD+ 6 N/C 7 N/C 8 N/C / +5V/ (+12V) 9 Ground 10 N/C 2.36 Audio Line-In/Out and MIC Connector (CN23) Pin Signal 1 MIC_L 2 MIC_R 3 Ground 4 Line IN_L 5 Line IN_R 6 Ground 7 Line OUT_L 8 Ground 9 Line OUT_R 10 +5V 2.
SubCompact Board GENE-LN05 Rev.B L1 SPD100_LED L2 SPD1K_LED L3 ACT_LED L4 +3.3V 2.38 RJ-45 Ethernet #1 (CN25) Pin Signal Pin Signal R1 GPHY_MDIO0+ R2 GPHY_MDIO0- R3 GPHY_MDIO1+ R4 GPHY_MDIO1- R5 TCD0 R6 TCD1 R7 GPHY_MDIO2+ R8 GPHY_MDIO2- R9 GPHY_MDIO3+ R10 GPHY_MDIO3- L1 SPD100_LED L2 SPD1K_LED L3 ACT_LED L4 +3.3V 2.39 Digital I/O Connector (CN26) Note: The max. rating of Pin 1 ~ Pin 8 is 3.3V@8mA The max. rating of Pin 9 is 3.3V@0.
SubCompact Board BIOS Setting (I2C address) Connector Definition Port 1 @6Eh GENE-LN05 Rev.
SubCompact Board GENE-LN05 Rev.B 2.41 LVDS Inverter Connector (CN28) Pin Signal 1 +5V / +12V (1A) 2 Brightness Control 3 Ground 4 Ground 5 Backlight Enable 2.42 LVDS Output (CN29) Pin Signal Pin Signal 1 Back-Light Enable 2 Back-Light Control 3 LCD Volt. 4 Ground 5 LA_CLK# 6 LA_CLK 7 LCD Volt.
SubCompact Board GENE-LN05 Rev.B 2.43 USB Port 1 & 2 (CN30) Pin Signal Pin Signal 1 +5V Standby 5 +5V Standby 2 Data0- 6 Data1- 3 Data0+ 7 Data1+ 4 Ground 8 Ground 2.44 PS/2 Keyboard & Mouse (CN31) Pin Signal Pin Signal 1 Keyboard Data 2 Keyboard Clock 3 Ground 4 +5V 5 Mouse Data 6 Mouse Clock 2.45 COM Port #1 (CN32) Pin Signal Pin Signal 1 DCDA 2 RXA 3 TXA 4 DTRA 5 Ground 6 DSRA 7 RTSA 8 CTSA 9 RIA 2.
SubCompact Board GENE-LN05 Rev.B 9 +5 Volt. 10 CRT_PLUG# 11 N/C 12 DDCDATA 13 HSYNC 14 VSYNC 15 DDCCLK 2.47 SIM Card Socket (CN34) Pin Signal Pin Signal 1 UIM_PWR 2 UIM_RST 3 UIM_CLK 4 Ground 5 UIM_VPP 6 UIM_DATA Signal Pin Signal 1 Ground 26 Ground 2 PDD3 27 PDD11 3 PDD4 28 PDD12 4 PDD5 29 PDD13 5 PDD6 30 PDD14 6 PDD7 31 PDD15 7 PDCS#1 32 PDCS#3 8 Ground 33 Ground 9 Ground 34 PDIOR# 2.
SubCompact Board GENE-LN05 Rev.B 16 Ground 41 IDERST# 17 Ground 42 PIORDY 18 PDA2 43 N/C 19 PDA1 44 +3.3V 20 PDA0 45 DASP# 21 PDD0 46 PDIAG# 22 PDD1 47 PDD8 23 PDD2 48 PDD9 24 N/C 49 PDD10 25 Ground 50 Ground Signal Pin Signal 1 PCIE_WAKE# 2 +3.3V Standby 3 N/C 4 Ground 5 N/C 6 +1.5V 7 CLKREQ# 8 UIM_PWR 9 Ground 10 UIM_DATA 11 MCARD_CLK# 12 UIM_CLK 13 MCARD_CLK 14 UIM_RESET 15 Ground 16 UIM_VPP 17 N/C 18 Ground 2.
SubCompact Board GENE-LN05 Rev.B 31 PCIE_TXN1 32 SMBDATA 33 PCIE_TXP1 34 Ground 35 Ground 36 USB_Data8- 37 Ground 38 USB_Data8+ 39 +3.3V Standby 40 Ground 41 +3.3V Standby 42 N/C 43 Ground 44 N/C 45 N/C 46 N/C 47 N/C 48 +1.5V 49 N/C 50 Ground 51 N/C 52 +3.3V Standby 2.
SubCompact Board GENE-LN05 Rev.
SubCompact Board GENE-LN05 Rev.
SubCompact Board 3.1 GENE-LN05 Rev.B System Test and Initialization These routines test and initialize board hardware. If the routines encounter an error during the tests, you will either hear a few short beeps or see an error message on the screen. There are two kinds of errors: fatal and non-fatal. The system can usually continue the boot up sequence with non-fatal errors.
SubCompact Board 3.2 GENE-LN05 Rev.B AMI BIOS Setup AMI BIOS ROM has a built-in Setup program that allows users to modify the basic system configuration. This type of information is stored in battery-backed CMOS RAM so that it retains the Setup information when the power is turned off. Entering Setup Power on the computer and press or immediately. This will allow you to enter Setup. Main Set the date, use tab to switch between date elements.
SubCompact Board GENE-LN05 Rev.B Chapter 4 Driver Installation .
SubCompact Board GENE-LN05 Rev.B The GENE-LN05 Rev.B comes with an AutoRun CD-ROM that contains all drivers and utilities that can help you to install the driver automatically. Insert the driver CD, the driver CD-title will auto start and show the installation guide. If not, please follow the sequence below to install the drivers.
SubCompact Board 4.1 GENE-LN05 Rev.B Installation: Insert the GENE-LN05 Rev.B CD-ROM into the CD-ROM drive. And install the drivers from Step 1 to Step 7 in order. Step 1 – Install Chipset Driver 1. Click on the STEP1-CHIPSET folder and double click on the infinst_autol.exe 2. Follow the instructions that the window shows 3. The system will help you install the driver automatically Step 2 – Install VGA Driver 1. Click on the STEP2-VGA folder and select the OS folder your system is 2.
SubCompact Board GENE-LN05 Rev.B Step 4 –Install Audio Driver 1. Click on the STEP4-AUDIO folder and select the OS folder your system is 2. Double click on Setup.exe file located in each OS folder 3. Follow the instructions that the window shows 4. The system will help you install the driver automatically Step 5 –Install TPM Driver (Optional) 1. Click on the STEP5-TPM (Option) folder and double click on the Setup.exe 2. Follow the instructions that the window shows 3.
SubCompact Board GENE-LN05 Rev.
SubCompact Board GENE-LN05 Rev.B A.1 Programming GENE-LN05 Rev.B utilizes W83627DHG-P chipset as its watchdog timer controller. Below are the procedures to complete its configuration and the AAEON intial watchdog timer program is also attached based on which you can develop customized program to fit your application.
SubCompact Board GENE-LN05 Rev.B (3) Exit the W83627DHG config Mode. Undesired result may occur if the config Mode is not exited normally. (1) Enter the W83627DHG config Mode To enter the W83627DHG config Mode, two special I/O write operations are to be performed during Wait for Key state. To ensure the initial state of the key-check logic, it is necessary to perform two write operations to the Special Address port (2EH).
SubCompact Board = 010 GENE-LN05 Rev.B Power LED pin is driven low. = 011 Power LED pin outputs 2Hz pulse with 50% duty cycle. = 100 Power LED pin outputs 1Hz pulse with 50% duty cycle. = 101 Power LED pin outputs 4Hz pulse with 50% duty cycle. = 110 Power LED pin outputs 0.25Hz pulse with 50% duty cycle. =111 Power LED pin outputs 0.25Hz pulse with 50% duty cycle.. Bit 4 Bit 3 Bit 2 : WDTO# count mode is 1000 times faster. =0 Disable. =1 Enable. : select WDTO# count mode.
SubCompact Board GENE-LN05 Rev.B WatchDog Timer Register II (Index=F6h, Default=00h) Bit 7-0 = 0 x 00 Time-out Disable = 0 x 01 Time-out occurs after 1 second/minute = 0 x 02 Time-out occurs after 2 second/minutes = 0 x 03 Time-out occurs after 3 second/minutes ………………………………..
SubCompact Board =1 GENE-LN05 Rev.B Force Watchdog Timer time-out event: this bit is self-clearing Bit 4 Bit 3-0 : Watchdog Timer Status. R/W =1 Watchdog Timer time-out occurred =0 Watchdog Timer counting : These bits select IRQ resource for Watchdog. Setting of 2 selects SMI.
SubCompact Board GENE-LN05 Rev.B A.2 W83627DHG Watchdog Timer Initial Program Example: Setting 10 sec.
SubCompact Board GENE-LN05 Rev.B ;/////////////////////////////////////////////////////////////////////////////////////////////// Dec dx Mov al,0f5h ;CRF5 (PLED mode register) Out dx,al Inc dx In al,dx And al,not 08h ;Set second as counting unit Out dx,al ;/////////////////////////////////////////////////////////////////////////////////////////////// Dec dx Mov al,0f6h ; CRF6 Out dx,al Inc dx Mov al,10 ;Set timeout interval as 10 sec.
SubCompact Board GENE-LN05 Rev.
SubCompact Board B.1 I/O Address Map Appendix B I/O Information B - 2 GENE-LN05 Rev.
SubCompact Board GENE-LN05 Rev.
SubCompact Board B.2 1st MB Memory Address Map Appendix B I/O Information B - 4 GENE-LN05 Rev.
SubCompact Board GENE-LN05 Rev.B B.3 IRQ Mapping Chart B.
SubCompact Board GENE-LN05 Rev.
SubCompact Board GENE-LN05 Rev.B C.1 List of Mating Connectors and Cables The table notes mating connectors and available cables. Connector Function Label CN2 CN3 CN4 Mating Connector Vendor CPU Fan Connector +5VSB Output w/ SMBus External +5VSB Power Input and PS_ON# Model no.
SubCompact Board GENE-LN05 Rev.
