SubCompact Board GENE-QM77 GENE-QM77 Intel® 3rd Generation CoreTM i7/i5 Mobile Processor 10/100/1000Base-TX Ethernet 2 USB3.0, 6 USB 2.0, 4 COM, 8-bit Digital I/O 2 SATA 6.0Gb/s (Optional RAID) 1 CFast™, 1 Mini Card, LPC GENE-QM77 Manual Rev.A 2nd Ed. Feb.
SubCompact Board GENE-QM77 Copyright Notice This document is copyrighted, 2014. All rights are reserved. The original manufacturer reserves the right to make improvements to the products described in this manual at any time without notice. No part of this manual may be reproduced, copied, translated, or transmitted in any form or by any means without the prior written permission of the original manufacturer. Information provided in this manual is intended to be accurate and reliable.
SubCompact Board GENE-QM77 Acknowledgments All other products’ name or trademarks are properties of their respective owners. AMI is a trademark of American Megatrends Inc. CFast™ is a trademark of the Compact Flash Association. Intel® and Core™ are trademarks of Intel® Corporation. Microsoft Windows® is a registered trademark of Microsoft Corp. ITE is a trademark of Integrated Technology Express, Inc.
SubCompact Board GENE-QM77 Packing List Before you begin installing your card, please make sure that the following materials have been shipped: 1 Cooler 1 DVD-ROM for Manual (in PDF Format) and Drivers 1 GENE-QM77 If any of these items should be missing or damaged, please contact your distributor or sales representative immediately.
SubCompact Board GENE-QM77 Contents Chapter 1 General Information 1.1 Introduction ................................................................ 1-2 1.2 Features .................................................................... 1-3 1.3 Specifications ............................................................ 1-4 Chapter 2 Quick Installation Guide 2.1 Safety Precautions .................................................. 2-2 2.2 Location of Connectors and Jumpers ...................... 2-3 2.
SubCompact Board GENE-QM77 2.15 Touch Screen 4/5/8-wire Selection (JP10) ........... 2-14 2.16 Clear CMOS (JP11) .............................................. 2-14 2.17 AT/ATX Power Supply Mode Selection (JP12) ..... 2-14 2.18 LVDS Port 1 Inverter/Backlight Connector (CN1) . 2-15 2.19 External +12V Input (CN2) .................................... 2-15 2.20 USB2.0 Port 7 and Port 8 (CN3) ........................... 2-16 2.21 USB2.0 Port 5 and Port 6 (CN4) ........................... 2-16 2.22 USB2.
SubCompact Board GENE-QM77 2.39 Realtek LAN (RJ-45) Port (CN23) ......................... 2-35 2.40 Intel LAN (RJ-45) Port (CN24) .............................. 2-36 2.41 USB Port 1 and Port 2 (CN25) .............................. 2-37 2.42 VGA/ DVI Ports (depend on hardware configuration) (CN26) ........................................................................... 2-38 2.43 COM Port 1 (D-SUB 9) (CN27) ............................. 2-40 2.44 CFast™ Slot (CN28) .......................................
SubCompact Board GENE-QM77 B.4 DMA Channel Assignments.……………………… .B-5 Appendix C Mating Connector C.1 List of Mating Connectors and Cables.................. C-2 Appendix D RAID & AHCI Settings D.1 Setting RAID ......................................................... D-2 D.2 Setting AHCI ......................................................... D-9 Appendix E Electrical Specifications for I/O Ports E.1 Electrical Specifications for I/O Ports .....................
SubCompact Board GENE-QM77 Chapter 1 General Information Chapter 1 General Information 1- 1
SubCompact Board GENE-QM77 1.1 Introduction The GENE-QM77 supports Intel® 3rd Generation Intel® Core™ i7/i5 Mobile processor which when paired with the Intel® QM77/HM76 chipset offers a high performance computing platform with low power consumption. This new product supports 204-pin DDR3 SODIMM at speeds of 1066/1333/1600 MHz, up to 8 GB. One CFast™ and two SATA 6.0Gb/s (Optional RAID) interfaces provide ample storages. With dual Gigabit Ethernet, four COM ports, two USB3.0 and six USB2.
SubCompact Board GENE-QM77 1.2 Features Intel® 3rd Generation Core™ i7/i5 Mobile Processor Intel® QM77/HM76 204-pin DDR3 1066/1333/1600 MHz SODIMM x 1, Up to 8 GB Gigabit Ethernet x 2 CRT, 18/24-bit Dual-Channel LVDS LCD x 2, DVI x 1 2CH HD Audio SATA 6.0Gb/s x 2 (Optional RAID), CFast x 1 USB3.0 x 2, USB2.
SubCompact Board GENE-QM77 1.3 Specifications System From Factor 3.
SubCompact Board GENE-QM77 Display: Supports CRT/LCD, DVI/LCD simultaneous / dual view displays Intel® QM77/HM76 integrated Chipset Memory Shared system memory up to 512MB Resolution Up to 2048x1536 for CRT Up to 1920 x 1200 for LCD, DVI DVI DVI x 1 I/O: ITE IT8728F + Fintek F81216D SATA 6.0Gb/s x 2 , CFast™ x 1 Storage Serial Port RS-232 x 3 RS-232/422/485 (auto flow) x 1 USB USB3.0 x 2, USB2.
SubCompact Board GENE-QM77 Chapter 2 Quick Installation Guide Chapter 2 Quick Installation Guide 2-1
SubCompact Board GENE-QM77 2.1 Safety Precautions Always completely disconnect the power cord from your board whenever you are working on it. Do not make connections while the power is on, because a sudden rush of power can damage sensitive electronic components. Always ground yourself to remove any static charge before touching the board. Modern electronic devices are very sensitive to static electric charges. Use a grounding wrist strap at all times.
SubCompact Board GENE-QM77 2.
SubCompact Board Solder Side Solder Side Chapter 2 Quick Installation Guide 2-4 GENE-QM77
SubCompact Board GENE-QM77 2.
SubCompact Board Solder Side Solder Side Chapter 2 Quick Installation Guide 2-6 GENE-QM77
SubCompact Board GENE-QM77 2.4 List of Jumpers The board has a number of jumpers that allow you to configure your system to suit your application.
SubCompact Board GENE-QM77 2.5 List of Connectors The board has a number of connectors that allow you to configure your system to suit your application. The table below shows the function of each board's connectors: Label Function CN1 LVDS Port 1 Inverter / Backlight Connector CN2 External +12V Input CN3 USB 2.0 Ports 7 and 8 CN4 USB 2.0 Ports 5 and 6 CN5 USB 2.
SubCompact Board GENE-QM77 CN20 CPU FAN CN22 +5V Output for SATA HDD CN23 Realtek LAN (RJ-45) Port CN24 Intel LAN (RJ-45) Port CN25 USB Ports 1 and 2 CN26 VGA / DVI Ports (depend on hardware configuration) CN27 COM Port 1 (D-SUB 9) CN28 CFast Slot CN29 DDR3 SODIMM Slot CN30 Mini Card Slot SATA1 SATA Port1 Connector SATA2 SATA Port 2 Connector Chapter 2 Quick Installation Guide 2-9
SubCompact Board GENE-QM77 2.6 Setting Jumpers You configure your card to match the needs of your application by setting jumpers. A jumper is the simplest kind of electric switch. It consists of two metal pins and a small metal clip (often protected by a plastic cover) that slides over the pins to connect them. To “close” a jumper you connect the pins with the clip. To “open” a jumper you remove the clip. Sometimes a jumper will have three pins, labeled 1, 2 and 3.
SubCompact Board GENE-QM77 2.7 LVDS Port 2 Operating VDD Selection (JP2) 1 2 3 +5V 1 2 3 +3.3V JP2 Function 1-2 +5V 2-3 +3.3V (Default) 2.8 LVDS Port 1 Backlight Inverter VCC Selection (JP3) 1 2 3 +12V 1 2 3 +5V JP3 Function 1-2 +12V 2-3 +5V (Default) 2.
SubCompact Board GENE-QM77 2.10 LVDS Port 1 Operating VDD Selection (JP5) 1 2 3 +5V 1 2 3 +3.3V JP5 Function 1-2 +5V 2-3 +3.3V (Default) 2.11 LVDS Port 1 Backlight Lightness Control Mode Selection (JP6) 1 2 3 VR Mode 1 2 3 PWM Mode JP6 Function 1-2 VR Mode (Default) 2-3 PWM Mode 2.
SubCompact Board 2-3 GENE-QM77 PWM Mode 2.13 COM2 Pin8 Function Selection (JP8) +12V Ring JP8 Function 1-2 +12V 3-4 Ring (Default) 5-6 +5V +5V 2.
SubCompact Board 8 PWR_LED+ 9 H/W RESET- 10 H/W RESET+ GENE-QM77 2.15 Touch Screen 4/5/8-Wire Selection (JP10) 1 2 3 4/8-wire mode 1 2 3 5-wire mode JP10 Function 1-2 4/8-wire mode (Default) 2-3 5-wire mode 2.16 Clear CMOS (JP11) 1 2 3 Normal 1 2 3 Clear CMOS JP11 Function 1-2 Normal (Default) 2-3 Clear CMOS 2.
SubCompact Board GENE-QM77 2.18 LVDS Port 1 Inverter/ Backlight Connector (CN1) 1 BLK_PWR 2 BKL_CONTROL 3 GND 4 GND 5 BKL_ENABLE Pin Pin Name Signal Type Signal Level 1 BKL_PWR PWR +5V / +12V 2 BKL_CONTROL OUT 3 GND GND 4 GND GND 5 BKL_ENABLE OUT +5V Note: LVDS1 BKL_PWR can be set to +5V or +12V by JP3. LVDS1 BKL_CONTROL can be set by JP6. 2.
SubCompact Board GENE-QM77 2.20 USB2.0 Port 7 and Port 8 (CN3) +5VSB USB7_DUSB7_D+ GND GND 1 2 9 10 GND GND USB8_D+ USB8_D+5VSB Pin Pin Name Signal Type Signal Level 1 +5VSB PWR +5V 2 GND GND 3 USB7_D- DIFF 4 GND GND 5 USB7_D+ DIFF 6 USB8_D+ DIFF 7 GND GND 8 USB8_D- DIFF 9 GND GND 10 +5VSB PWR +5V 2.21 USB2.
SubCompact Board GENE-QM77 3 USB5_D- DIFF 4 GND GND 5 USB5_D+ DIFF 6 USB6_D+ DIFF 7 GND GND 8 USB6_D- DIFF 9 GND GND 10 +5VSB PWR +5V 2.22 USB2.
SubCompact Board 10 +5VSB GENE-QM77 PWR +5V 2.23 External +5VSB Input (CN6) 1 PS_ON# 2 GND 3 +5VSB Pin Pin Name Signal Type Signal Level 1 PS_ON# OUT +3.3V 2 GND GND 3 +5VSB PWR +5V 2.24 LVDS Port 2 Inverter/ Backlight Connector (CN7) 1 BLK_PWR 2 BKL_CONTROL 3 GND 4 GND 5 BKL_ENABLE Pin Pin Name Signal Type Signal Level 1 BKL_PWR PWR +5V / +12V 2 BKL_CONTROL OUT 3 GND GND 4 GND GND 5 BKL_ENABLE OUT Note: LVDS2 BKL_PWR can be set to +5V or +12V by JP4.
SubCompact Board GENE-QM77 2.25 Audio I/O Port Connector (CN8) 1 10 MIC_L MIC_R GND_AUDIO LINE_L_IN LINE_R_IN GND_AUDIO LEFT_OUT GND_AUDIO RIGHT_OUT +5V_AUDIO Pin Pin Name Signal Type 1 MIC_L IN 2 MIC_R IN 3 GND_AUDIO GND 4 LINE_L_IN IN 5 LINE_R_IN IN 6 GND_AUDIO GND 7 LEFT_OUT OUT 8 GND_AUDIO GND 9 RIGHT_OUT OUT 10 +5V_AUDIO PWR Signal Level +5V 2.
SubCompact Board GENE-QM77 Pin Pin Name Signal Type 1 BKL_ENABLE OUT 2 BKL_CONTROL OUT 3 LCD_PWR PWR 4 GND GND 5 LVDS_A_CLK- DIFF 6 LVDS_A_CLK+ DIFF 7 LCD_PWR PWR 8 GND GND 9 LVDS_DA0- DIFF 10 LVDS_DA0+ DIFF 11 LVDS_DA1- DIFF 12 LVDS_DA1+ DIFF 13 LVDS_DA2- DIFF 14 LVDS_DA2+ DIFF 15 LVDS_DA3- DIFF 16 LVDS_DA3+ DIFF 17 DDC_DATA I/O +3.3V 18 DDC_CLK I/O +3.
SubCompact Board GENE-QM77 24 LVDS_DB2+ DIFF 25 LVDS_DB3- DIFF 26 LVDS_DB3+ DIFF 27 LCD_PWR PWR 28 GND GND 29 LVDS_B_CLK- DIFF 30 LVDS_B_CLK+ DIFF +3.3V/+5V Note: LVDS1 LCD_PWR can be set to +3.3V or +5V by JP5. 2.27 LVDS Port 2 Connector (CN10) PIN 29 PIN 30 PIN 1 PIN 2 Pin Pin Name Signal Type 1 BKL_ENABLE OUT 2 BKL_CONTROL OUT 3 LCD_PWR PWR 4 GND GND 5 LVDS_A_CLK- DIFF 6 LVDS_A_CLK+ DIFF 7 LCD_PWR PWR Signal Level +3.3V/+5V +3.
SubCompact Board GENE-QM77 8 GND GND 9 LVDS_DA0- DIFF 10 LVDS_DA0+ DIFF 11 LVDS_DA1- DIFF 12 LVDS_DA1+ DIFF 13 LVDS_DA2- DIFF 14 LVDS_DA2+ DIFF 15 LVDS_DA3- DIFF 16 LVDS_DA3+ DIFF 17 DDC_DATA I/O +3.3V 18 DDC_CLK I/O +3.3V 19 LVDS_DB0- DIFF 20 LVDS_DB0+ DIFF 21 LVDS_DB1- DIFF 22 LVDS_DB1+ DIFF 23 LVDS_DB2- DIFF 24 LVDS_DB2+ DIFF 25 LVDS_DB3- DIFF 26 LVDS_DB3+ DIFF 27 LCD_PWR PWR 28 GND GND 29 LVDS_B_CLK- DIFF 30 LVDS_B_CLK+ DIFF +3.
SubCompact Board GENE-QM77 2.
SubCompact Board GENE-QM77 3 RS422_RX+ IN 4 NC 5 RS422_TX+ 6 NC 7 RS422_RX- IN 8 NC/+5V/+12V PWR 9 GND GND Pin Pin Name Signal Type Signal Level 1 RS485_D- I/O ±5V 2 NC 3 NC 4 NC 5 RS485_D+ I/O ±5V 6 NC 7 NC 8 NC/+5V/+12V PWR +5V/+12V 9 GND GND OUT ±5V +5V/+12V RS-485 Note: COM2 RS-232/422/485 can be set by BIOS setting. Default is RS-232. Pin 8 function can be set by JP8.
SubCompact Board GENE-QM77 2.29 LPT/ Digital I/O Port Connector (CN12) LPT Mode LPT Mode 1 DIO Mode 1 2 AFD# ERROR# PRINT# SLIN# GND GND GND GND GND GND GND GND N.C STROBE# PD0 PD1 PD2 PD3 PD4 PD5 PD6 PD7 ACK# BUSY PE SLCT 25 2 N.C N.C N.C N.C GND GND GND GND GND GND GND GND N.C N.C DIO0 DIO1 DIO2 DIO3 N.C N.C N.C N.
SubCompact Board GENE-QM77 14 GND GND 15 PD6 I/O 16 GND GND 17 PD7 I/O 18 GND GND 19 ACK# IN 20 GND GND 21 BUSY IN 22 GND GND 23 PE IN 24 GND GND 25 SLCT IN 26 NC Note: LPT / Digital IO can be set by BIOS setting. Default is LPT Function DIO Mode PT Mode 1 DIO Mode 1 2 AFD# ERROR# PRINT# SLIN# GND GND GND GND GND GND GND GND N.C 25 26 2 N.C N.C N.C N.C GND GND GND GND GND GND GND GND N.C N.C DIO0 DIO1 DIO2 DIO3 N.C N.C N.C N.
SubCompact Board Pin Pin Name 1 NC 2 NC 3 DIO0 4 NC 5 DIO1 6 NC 7 DIO2 8 NC 9 GENE-QM77 Signal Type Signal Level I/O +5V I/O +5V I/O +5V DIO3 I/O +5V 10 GND GND 11 NC 12 GND 13 NC 14 GND 15 NC 16 GND 17 NC 18 GND GND 19 DIO7 I/O 20 GND GND 21 DIO6 I/O 22 GND GND 23 DIO5 I/O GND GND GND +5V +5V +5V Chapter 2 Quick Installation Guide 2-27
SubCompact Board GENE-QM77 24 GND GND 25 DIO4 I/O 26 NC GPIO Port # / Pin Name Port 1/DIO0 Port 2/DIO1 Port 3/DIO2 Port 4/DIO3 Port 5/DIO4 Port 6/DIO5 Port 7/DIO6 Port 8/DIO7 Location (Pin #) 3 5 7 9 25 23 21 19 +5V I/O Port Access Address Bit 0 of 0xA06 Bit 1 of 0xA06 Bit 2 of 0xA06 Bit 3 of 0xA06 Bit 0 of 0xA07 Bit 1 of 0xA07 Bit 2 of 0xA07 Bit 3 of 0xA07 2.
SubCompact Board GENE-QM77 6 CTS IN 7 DTR OUT 8 RI IN 9 GND GND ±9V 2.31 LPC Port Connector (CN14) LAD0 LAD1 LAD2 LAD3 +3.3V LFRAME# LRESET# GND LCLK LDRQ0 LDRQ1 SERIRQ 1 12 Pin Pin Name Signal Type Signal Level 1 LAD0 I/O +3.3V 2 LAD1 I/O +3.3V 3 LAD2 I/O +3.3V 4 LAD3 I/O +3.3V 5 +3.3V PWR +3.3V 6 LFRAME# IN 7 LRESET# OUT 8 GND GND 9 LCLK OUT 10 LDRQ0 IN 11 LDRQ1 IN +3.
SubCompact Board 12 GENE-QM77 SERIRQ I/O +3.3V Signal Level 2.32 COM Port 4 Connector (CN15) DCD DSR RX RTS TX CTS DTR RI GND Pin Pin Name Signal Type 1 DCD IN 2 DSR IN 3 RX IN 4 RTS OUT ±9V 5 TX OUT ±9V 6 CTS IN 7 DTR OUT 8 RI IN 9 GND GND 2.
SubCompact Board GENE-QM77 Pin Pin Name Signal Type 1 UIM_PWR PWR 2 UIM_RST IN 3 UIM_CLK IN 4 GND GND 5 UIM_VPP PWR 6 UIM_DATA I/O Signal Level 2.
SubCompact Board GENE-QM77 2.35 +5VSB Output w/SMBus (CN18) 1 SMB_DATA GND SMB_CLK GND PS_ON# 6 +5VSB Pin Pin Name Signal Type Signal Level 1 SMB_DATA I/O +3.3V 2 GND GND 3 SMB_CLK I/O 4 GND GND 5 PS_ON# OUT +3.3V 6 +5VSB PWR +5V +3.3V 2.
SubCompact Board 8 Wires GENE-QM77 4 LEFT EXCITE IN 5 RIGHT EXCITE IN 6 TOP SENSE IN 7 BOTTOM SENSE IN 8 LEFT SENSE IN 9 RIGHT SENSE IN 4 Wires 5 Wires 4-wire 1 GND TOP BOTTOM LEFT RIGHT NC NC NC NC 9 1 9 1 GND UL(Y) UR(H) LL(L) LR(X) SENSE(S) NC NC NC 9 Pin Pin Name Signal Type 1 GND GND 2 TOP IN 3 BOTTOM IN 4 LEFT IN 5 RIGHT IN 6 NC 7 NC 8 NC 9 NC Signal Level Chapter 2 Quick Installation Guide 2-33
ND OP TTOM EFT GHT NC NC NC NC SubCompact Board 4 Wires GENE-QM77 5 Wires 5-wire 1 1 GND UL(Y) UR(H) LL(L) LR(X) SENSE(S) NC NC NC 9 9 Pin Pin Name Signal Type 1 GND GND 2 UL(Y) IN 3 UR(H) IN 4 LL(L) IN 5 LR(X) IN 6 SENSE(S) IN 7 NC 8 NC 9 NC Note: Touch mode can be set by JP10 2.
SubCompact Board GENE-QM77 Pin Pin Name Signal Type 1 GND GND 2 FAN_POWER PWR 3 FAN_TAC IN Signal Level +5V 2.38 +5V Output for SATA HDD (CN22) +5V GND Pin Pin Name Signal Type Signal Level 1 +5V PWR +5V 2 GND GND 2.
SubCompact Board GENE-QM77 5 MDI2- DIFF 6 MDI1- DIFF 7 MDI3+ DIFF 8 MDI3- DIFF 2.
SubCompact Board GENE-QM77 2.
SubCompact Board GENE-QM77 16 GND GND 17 USB2_SSTX− DIFF 18 USB2_SSTX+ DIFF 2.
SubCompact Board GENE-QM77 12 DDC_DATA I/O +5V 13 HSYNC OUT 14 VSYNC OUT 15 DDC_CLK I/O +5V Pin Pin Name Signal Type Signal Level 1 TMDS_DAT2+ DIFF 2 TMDS_DAT2- DIFF 3 GND GND 4 VGA_DDC_CLK I/O 5 VGA_DDC _DATA I/O 6 DVI_DDC_CLK I/O +5V 7 DVI_DDC_DATA I/O +5V 8 VSYNC OUT 9 TMDS_DAT1- DIFF 10 TMDS_DAT1+ DIFF 11 GND GND 12 TMDS_DAT3- DIFF 13 TMDS_DAT3+ DIFF 14 +5V PWR 15 GND GND 16 HPLG_DETECT IN 17 TMDS_DAT0- DIFF DVI +5V Chapter 2 Qui
SubCompact Board GENE-QM77 18 TMDS_DAT0+ DIFF 19 GND GND 20 NC 21 NC 22 GND GND 23 TMDS_CLK+ DIFF 24 TMDS_CLK- DIFF C1 RED OUT C2 GREEN OUT C3 BLUE OUT C4 HSYNC OUT C5 GND_ANALOG GND 2.
SubCompact Board GENE-QM77 7 RTS OUT 8 CTS IN 9 RI IN ±9V 2.
SubCompact Board GENE-QM77 PC12 NC PC13 +3.3V PWR +3.3V PC14 +3.3V PWR +3.3V PC15 GND GND PC16 GND GND PC17 NC 2.45 DDR3 SODIMM Slot (CN29) Standard specification 2.46 Mini Card Slot (CN30) Pin Pin Name Signal Type 1 PCIE_WAKE# IN 2 +3.3VSB PWR 3 NC 4 GND 5 NC 6 +1.5V PWR 7 PCIE_CLK_REQ# IN 8 UIM_PWR PWR 9 GND GND 10 UIM_DATA I/O 11 PCIE_REF_CLK- DIFF 12 UIM_CLK IN Chapter 2 Quick Installation Guide 2-42 Signal Level +3.3V GND +1.
SubCompact Board GENE-QM77 13 PCIE_REF_CLK+ DIFF 14 UIM_RST IN 15 GND GND 16 UIM_VPP PWR 17 NC 18 GND 19 NC 20 W_DISABLE# OUT 21 GND GND 22 PCIE_RST# OUT 23 PCIE_RX- DIFF 24 +3.3VSB PWR 25 PCIE_RX+ DIFF 26 GND GND 27 GND GND 28 +1.5V PWR 29 GND GND 30 SMB_CLK I/O 31 PCIE_TX- DIFF 32 SMB_DATA I/O 33 PCIE_TX+ DIFF 34 GND GND 35 GND GND 36 USB_D- DIFF GND +3.3V +3.3V +3.3V +1.5V +3.3V +3.
SubCompact Board GENE-QM77 37 GND GND 38 USB_D+ DIFF 39 +3.3VSB PWR 40 GND GND 41 +3.3VSB PWR 42 NC 43 GND 44 NC 45 NC 46 NC 47 NC 48 +1.5V 49 NC 50 GND 51 NC 52 +3.3VSB +3.3V +3.3V GND PWR +1.5V GND PWR +3.3V Signal Level 2.
SubCompact Board GENE-QM77 3 SATA_TX- DIFF 4 GND GND 5 SATA_RX- DIFF 6 SATA_RX+ DIFF 7 GND GND 2.
SubCompact Board GENE-QM77 Below Table for China RoHS Requirements 产品中有毒有害物质或元素名称及含量 AAEON Main Board/ Daughter Board/ Backplane 有毒有害物质或元素 部件名称 印刷电路板 及其电子组件 外部信号 连接器及线材 铅 汞 镉 六价铬 多溴联苯 多溴二苯醚 (Pb) (Hg) (Cd) (Cr(VI)) (PBB) (PBDE) × ○ ○ ○ ○ ○ × ○ ○ ○ ○ ○ O：表示该有毒有害物质在该部件所有均质材料中的含量均在 SJ/T 11363-2006 标准规定的限量要求以下。 X：表示该有毒有害物质至少在该部件的某一均质材料中的含量超出 SJ/T 11363-2006 标准规定的限量要求。 备注：此产品所标示之环保使用期限，系指在一般正常使用状况下。 Chapter 2 Quick Installation Guide 2-46
SubCompact Board GENE-QM77 Chapter 3 AMI BIOS Setup Chapter 3 AMI BIOS Setup 3-1
SubCompact Board 3.1 GENE-QM77 System Test and Initialization These routines test and initialize board hardware. If the routines encounter an error during the tests, you will either hear a few short beeps or see an error message on the screen. There are two kinds of errors: fatal and non-fatal. The system can usually continue the boot up sequence with non-fatal errors. System configuration verification These routines check the current system configuration against the values stored in the CMOS memory.
SubCompact Board 3.2 GENE-QM77 AMI BIOS Setup AMI BIOS ROM has a built-in Setup program that allows users to modify the basic system configuration. This type of information is stored in battery-backed CMOS RAM so that it retains the Setup information when the power is turned off. Entering Setup Power on the computer and press or immediately. This will allow you to enter Setup. Main Set the date, use tab to switch between date elements.
SubCompact Board GENE-QM77 Chapter 4 Driver Installation 0B .
SubCompact Board GENE-QM77 The GENE-QM77 comes with an AutoRun DVD-ROM that contains all drivers and utilities that can help you to install the driver automatically. Insert the driver DVD, the driver DVD-title will auto start and show the installation guide. If not, please follow the sequence below to install the drivers.
SubCompact Board 4.1 GENE-QM77 Installation: Insert the GENE-QM77 DVD-ROM into the DVD-ROM drive. And install the drivers from Step 1 to Step 10 in order. Step 1 – Install Chipset Driver 1. Click on the STEP1-CHIPSET folder and double click on the infinst_autol.exe file 2. Follow the instructions that the window shows 3. The system will help you install the driver automatically Step 2 – Install VGA Driver 1. Click on the STEP2-VGA folder and select the OS folder your system is 2.
SubCompact Board GENE-QM77 3. Follow the instructions that the window shows 4. The system will help you install the driver automatically ® Step 4 –Install LAN Driver (Intel LAN Chip) 1. Click on the STEP4-LAN(Intel) folder and select the OS folder your system is 2. Double click on the .exe file located in each OS folder 3. Follow the instructions that the window shows 4. The system will help you install the driver automatically Step 5 –Install Audio Driver 1.
SubCompact Board GENE-QM77 Step 7 – Install RAID & AHDI Driver Please refer to the Appendix D RAID & AHDI Settings Step 8 – Install TPM Driver 1. Click on the STEP8-TPM folder and select the OS folder your system is 2. Double click on the Setup.exe file located in each OS folder 3. Follow the instructions that the window shows 4. The system will help you install the driver automatically Step 9 –Install Touch Driver 1. Click on the STEP9-TOUCH folder and select the OS folder your system is 2.
SubCompact Board GENE-QM77 Appendix A Programming the Watchdog Timer Appendix A Programming the Watchdog Timer A-1
SubCompact Board GENE-QM77 A.1 Programming GENE-QM77 utilizes ITE IT8728F chipset as its watchdog timer controller. Below are the procedures to complete its configuration and the AAEON intial watchdog timer program is also attached based on which you can develop customized program to fit your application. Configuring Sequence Description After the hardware reset or power-on reset, the ITE 8728F enters the normal mode with all logical devices disabled except KBC.
SubCompact Board GENE-QM77 There are three steps to complete the configuration setup: (1) Enter the MB PnP Mode; (2) Modify the data of configuration registers; (3) Exit the MB PnP Mode. Undesired result may occur if the MB PnP Mode is not exited normally. (1) Enter the MB PnP Mode To enter the MB PnP Mode, four special I/O write operations are to be performed during Wait for Key state.
SubCompact Board GENE-QM77 WatchDog Timer Configuration Registers Configure Control (Index=02h) This register is write only. Its values are not sticky; that is to say, a hardware reset will automatically clear the bits, and does not require the software to clear them.
SubCompact Board GENE-QM77 WatchDog Timer Control Register (Index=71h, Default=00h) WatchDog Timer Configuration Register (Index=72h, Default=00h) WatchDog Timer Time-out Value Register (Index=73h, Default=00h) Appendix A Programming the Watchdog Timer A-5
SubCompact Board GENE-QM77 A.2 ITE8728F Watchdog Timer Initial Program .MODEL SMALL .CODE Main: CALL Enter_Configuration_mode CALL Check_Chip mov cl, 7 call Set_Logic_Device ;time setting mov cl, 10 ; 10 Sec dec al Watch_Dog_Setting: ;Timer setting mov al, cl mov cl, 73h call Superio_Set_Reg ;Clear by keyboard or mouse interrupt mov al, 0f0h mov cl, 71h call Superio_Set_Reg ;unit is second.
SubCompact Board GENE-QM77 ; game port enable mov cl, 9 call Set_Logic_Device Initial_OK: CALL Exit_Configuration_mode MOV AH,4Ch INT 21h Enter_Configuration_Mode PROC NEAR MOV SI,WORD PTR CS:[Offset Cfg_Port] MOV DX,02Eh MOV CX,04h Init_1: MOV AL,BYTE PTR CS:[SI] OUT DX,AL INC SI LOOP Init_1 RET Enter_Configuration_Mode ENDP Exit_Configuration_Mode PROC NEAR MOV AX,0202h CALL Write_Configuration_Data Appendix A Programming the Watchdog Timer A-7
SubCompact Board GENE-QM77 RET Exit_Configuration_Mode ENDP Check_Chip PROC NEAR MOV AL,20h CALL Read_Configuration_Data CMP AL,87h JNE Not_Initial MOV AL,21h CALL Read_Configuration_Data CMP AL,12h JNE Not_Initial Need_Initial: STC RET Not_Initial: CLC RET Check_Chip ENDP Read_Configuration_Data PROC NEAR MOV DX,WORD PTR CS:[Cfg_Port+04h] OUT DX,AL Appendix A Programming the Watchdog Timer A-8
SubCompact Board GENE-QM77 MOV DX,WORD PTR CS:[Cfg_Port+06h] IN AL,DX RET Read_Configuration_Data ENDP Write_Configuration_Data PROC NEAR MOV DX,WORD PTR CS:[Cfg_Port+04h] OUT DX,AL XCHG AL,AH MOV DX,WORD PTR CS:[Cfg_Port+06h] OUT DX,AL RET Write_Configuration_Data ENDP Superio_Set_Reg proc near push ax MOV DX,WORD PTR CS:[Cfg_Port+04h] mov al,cl out dx,al pop ax inc dx out dx,al ret Superio_Set_Reg endp.
SubCompact Board GENE-QM77 push ax push cx xchg al,cl mov cl,07h call Superio_Set_Reg pop cx pop ax ret Set_Logic_Device endp ;Select 02Eh->Index Port, 02Fh->Data Port Cfg_Port DB 087h,001h,055h,055h DW 02Eh,02Fh END Main Note: Interrupt level mapping 0Fh-Dh: not valid 0Ch: IRQ12 . .
SubCompact Board GENE-QM77 Appendix B I/O Information Appendix B I/O Information B-1
SubCompact Board B.
SubCompact Board GENE-QM77 Appendix B I/O Information B-3
SubCompact Board B.
SubCompact Board GENE-QM77 B.3 IRQ Mapping Chart B.
SubCompact Board GENE-QM77 Appendix C Mating Connector Appendix C Mating Connector C - 1
SubCompact Board GENE-QM77 C.1 List of Mating Connectors and Cables The table notes mating connectors and available cables.
SubCompact Board GENE-QM77 AAEON LPC Cable Serial Port Cable CN14 LPC Port JST SHR-12V-S-B CN15 COM Port 4 Connector Molex 51021-0900 CN16 UIM Connector Molex 51021-0600 N/A N/A CN17 P/S2 KB/MS Connector JST PHDR-06VS P/S2 KB/MS Cable 1700060152 PHR-6 N/A N/A SHR-9V-S-B N/A N/A 22-01-2035 N/A N/A CN18 CN19 CN20 External AUX Power and JST PS_ON# Touch Screen JST Connector CPU Fan Molex Connector CN22 +5Vout Connector BAT1 External RTC Molex Connector JST PHR-2 51021-020
SubCompact Board GENE-QM77 Appendix D RAID & AHCI Settings Appendix D RAID & AHCI Settings D-1
SubCompact Board GENE-QM77 D.1 Setting RAID OS installation to SETUP RAID Mode Step 1: Extract the f6fly-x86.zip from “Driver CD -> Step7-RAID&AHCI\WinXP_32” and copy below files to diskette. Step 2: Connect the USB Floppy drive to the board and insert the diskette from previous step.
SubCompact Board GENE-QM77 Step 3: Configure SATA Controller to RAID mode in BIOS SETUP Menu: Advanced -> SATA Configuration -> SATA Mode -> RAID Mode Step 4: Configure DVD/CD-ROM drive as the first boot device.
SubCompact Board GENE-QM77 Step 5: Save changes and exit BIOS SETUP Step 6: Press CTRL-I to enter RAID Configuration Utility Appendix D RAID & AHCI Settings D-4
SubCompact Board GENE-QM77 Step 7: Choose “1.
SubCompact Board GENE-QM77 Step 9 – Choose “Create Volume” and confirmed in next warning message.
SubCompact Board GENE-QM77 Step 10 – Exit RAID Configuration Utility and Reboot to DVD/CD-ROM device to install OS Step 11 – Press “F6” to install RAID driver Step 12 – Press “S” to install RAID driver Appendix D RAID & AHCI Settings D-7
SubCompact Board GENE-QM77 Step 13 – Choose “Intel(R) Mobile Express Chipset SATA RAID Controller” Step 14 – It will show the model you selected and then press ”ENTER”. Windows Setup will continue to install OS.
SubCompact Board GENE-QM77 D.2 Setting AHCI OS installation to SETUP AHCI Mode Step 1: Extract the f6fly-x86.zip from “Driver CD -> Step7 RAID&AHCI\WinXP_32” and copy below files to diskette. Step 2: Connect the USB Floppy drive to the board and insert the diskette from previous step.
SubCompact Board GENE-QM77 Step 3: Configure SATA Controller to RAID mode in BIOS SETUP Menu: Advanced -> SATA Configuration -> SATA Mode -> AHCI Mode Step 4: Configure DVD/CD-ROM drive as the first boot device.
SubCompact Board GENE-QM77 Step 5: Save changes and exit BIOS SETUP Step 6 – Boot to DVD/CD-ROM device to install OS Step 7 – Press “F6” to install AHCI driver Appendix D RAID & AHCI Settings D-11
SubCompact Board GENE-QM77 Step 8 – Press “S” to install AHCI driver Step 9 – Choose “Intel(R) 7 Series Chipset Family SATA AHCI Controller” Appendix D RAID & AHCI Settings D-12
SubCompact Board GENE-QM77 Step 10 – It will show the model you selected and then press ”ENTER”. Windows Setup will continue to install OS.
SubCompact Board GENE-QM77 Appendix E Electrical Specifications for I/O Ports Appendix E Electrical Specifications for I/O Ports E-1
SubCompact Board GENE-QM77 E.1 Electrical Specifications for I/O Ports I/O Reference Signal Name Rate Output CN1 VDD +5V/2A or +12V/2A CN7 VDD +5V/2A or +12V/2A CN3 +5V CN4 +5V CN5 +5V CN25 VCC +5V/1A (per channel) Audio I/O Port CN8 +5V +5V/1A LVDS Port 1 CN9 VCC LVDS Port 2 CN10 VCC COM Port 2 CN11 +5V/+12V Digital IO Port CN12 D0~D7 PS/2 Keyboard/Mouse Combo Port CN17 +5V +5V/1A CPU FAN CN20 VDD +12V/0.
SubCompact Board GENE-QM77 CFast Slot CN28 +3.3V +3.3V/0.5A Mini Card Slot CN30 +3.3VSB +1.5V +3.3V/1.1A +1.5V/0.375A LPC Port CN14 +3.3VCC +3.3V/0.
