SubCompact Board GENE-U15B GENE-U15B ® Intel Atom™Z5x0P Processor Intel ® System Controller Hub US15WP 10/100/1000Base-TX 1 SATA 3.0Gb/s, Onboard SST SSD 4 COM, 6 USB2.0, Digital I/O 1 Mini Card GENE-U15B Manual Rev.A 2nd Ed.
SubCompact Board GENE-U15B Copyright Notice This document is copyrighted, 2011. All rights are reserved. The original manufacturer reserves the right to make improvements to the products described in this manual at any time without notice. No part of this manual may be reproduced, copied, translated, or transmitted in any form or by any means without the prior written permission of the original manufacturer. Information provided in this manual is intended to be accurate and reliable.
SubCompact Board GENE-U15B Acknowledgments All other products’ name or trademarks are properties of their respective owners. Award is a trademark of Award Software International, Inc. CompactFlash™ is a trademark of the Compact Flash Association. Intel®, Atom are trademarks of Intel® Corporation. Microsoft Windows is a registered trademark of Microsoft Corp. ITE is a trademark of Integrated Technology Express, Inc.
SubCompact Board GENE-U15B Packing List Before you begin installing your card, please make sure that the following materials have been shipped: 1700060157 CD-ROM for manual (in PDF format) and drivers GENE-U15B Keyboard & Mouse Cable If any of these items should be missing or damaged, please contact your distributor or sales representative immediately.
SubCompact Board GENE-U15B Contents Chapter 1 General Information 1.1 Introduction................................................................ 1-2 1.2 Features .................................................................... 1-3 1.3 Specifications ............................................................ 1-4 Chapter 2 Quick Installation Guide 2.1 Safety Precautions .................................................... 2-2 2.2 Location of Connectors & Jumpers ........................... 2-3 2.
SubCompact Board GENE-U15B 2.17 LVDS Inverter +5V/+12V Connector (CN6) ............ 2-12 2.18 Touch Panel Connector (CN8)................................ 2-12 2.19 RS-232 Serial Port Connector (CN11) .................... 2-13 2.20 RS-232/422/485 Serial Port Connector (CN12)...... 2-13 2.21 Fan Connector (CN17) ............................................ 2-14 2.22 RS-232 Serial Port Connector (CN18) .................... 2-14 2.23 PS2 Keyboard/Mouse Connector (CN19) ............... 2-14 2.
SubCompact Board GENE-U15B Chapter 4 Driver Installation 4.1 Installation ................................................................. 4-3 Appendix A Programming The Watchdog Timer A.1 Programming .........................................................A-2 Appendix B I/O Information B.1 I/O Address Map ....................................................B-2 B.2 Memory Address Map............................................B-3 B.3 IRQ Mapping Chart ................................................
SubCompact Board GENE-U15B Chapter 1 General Information Chapter 1 General Information 1- 1
SubCompact Board GENE-U15B 1.1 Introduction AAEON, a leading embedded boards manufacturer, is pleased to announce the debut of their new generation 3.5” SubCompact Board—GENE-U15B. The GENE-U15B is a cutting-edge product that provides high performance and low power consumption in the embedded market. GENE-U15B adopts the latest Intel® Atom Z530P/Z510P processor and the system memory deploys with SODIMM DDR2 400/533 up to 2GB.
SubCompact Board GENE-U15B 1.2 Features z Intel® Atom™ Z530P/Z510P Processor z Intel® System Controller Hub US15WP z DDR2 400/533 SODIMM, Max. 2 GB z Gigabit Ethernet x 1 z CRT, 24-Bit Single Channel LVDS LCD z 2CH HD Audio z SATA 3.0Gb/s x 1, Onboard SSD Up To 4GB z USB2.
SubCompact Board GENE-U15B 1.3 Specifications System z Form Factor 3.5” z Processor Intel® Atom™Z530P 1.6 GHz, Z510P 1.1 GHz z System Memory 200-pin DDR2 SODIMM x 1, Max.
SubCompact Board GENE-U15B Temperature z Storage -40˚F~ 176˚F (-40˚C ~ 80˚C) Temperature z Operating Humidity 0%~90% relative humidity, non-condensing z MTBF (Hours) 700,000 Display: Supports CRT/LCD simultaneous/dual view displays z Chipset Intel® Z5x0P integrated z Memory Shared system memory up to 256 MB z Resolution Up to 1280x1024 for VGA; Up to 1366x768 for LCD z LCD Interface Up to 24-bit single channel LVDS z Storage SATA 3.
SubCompact Board GENE-U15B Chapter 2 Quick Installation Guide Chapter 2 Quick Installation Guide 2-1
SubCompact Board GENE-U15B 2.1 Safety Precautions Always completely disconnect the power cord from your board whenever you are working on it. Do not make connections while the power is on, because a sudden rush of power can damage sensitive electronic components. Always ground yourself to remove any static charge before touching the board. Modern electronic devices are very sensitive to static electric charges. Use a grounding wrist strap at all times.
SubCompact Board GENE-U15B 2.
SubCompact Board GENE-U15B Solder Side CN38 CN13 Chapter 2 Quick Installation Guide 2-4
SubCompact Board GENE-U15B 2.3 Mechanical Drawing 14.60 20.39 30.42 41.41 37.18 61.93 57.88 74.97 91.64 88.98 86.32 82.06 101.60 98.37 Component Side (12.55) 146.05 142.82 140.78 137.01 144.34 133.56 144.19 144.05 142.53 146.05 143.62 142.75 138.16 142.45 123.40 120.96 109.78 (12.55) 84.24 (13.35) 98.12 21.26 59.26 41.13 27.89 24.01 20.70 1.76 57.44 37.18 41.03 37.26 19.94 13.34 8.89 4.51 1.25 1.21 13.70 8.89 9.19 3.17 23.22 (17.30) 1.54 0.00 11.55 6.44 3.17 0.00 29.
SubCompact Board GENE-U15B 101.60 Solder Side 146.05 142.82 33.93 8.13 Chapter 2 Quick Installation Guide 2-6 98.37 101.60 49.15 36.30 0.00 0.
SubCompact Board GENE-U15B 2.4 List of Jumpers The board has a number of jumpers that allow you to configure your system to suit your application. The table below shows the function of each of the board's jumpers: Label Function JP1 LVDS-Inverter Voltage Control Selection JP2 LVDS-LCD +5V/+3.
SubCompact Board GENE-U15B CN17 Fan Connector CN18(COM3) RS-232 Serial Port Connector CN19 Keyboard/Mouse Connector CN20(COM4) RS-232 Serial Port Connector CN21 CPLD Programming Connector CN22 USB Connector CN23 Serial-ATA Connector CN27 12V input Power Jack Connector CN28 Output +5V_DUAL / PSON# /SM Bus Connector CN29 Front Panel Connector CN30 USB Connector CN31 Digital I/O Connector CN32 5V input Power Jack Connector CN34 USB Connector CN35 USB Connector CN36 Output Power
SubCompact Board GENE-U15B 2.6 Setting Jumpers You configure your card to match the needs of your application by setting jumpers. A jumper is the simplest kind of electric switch. It consists of two metal pins and a small metal clip (often protected by a plastic cover) that slides over the pins to connect them. To “close” a jumper you connect the pins with the clip. To “open” a jumper you remove the clip. Sometimes a jumper will have three pins, labeled 1, 2 and 3.
SubCompact Board GENE-U15B 2.7 LVDS Inverter Voltage Control Selection (JP1) JP1 Function 1-2 Voltage Control (Default) 2-3 NC 2.8 LVDS Panel +5V/+3.3V Selection (JP2) JP2 Function 1-2 +5V 2-3 +3.3V (Default) 2.9 LVDS-Inverter +5V/+12V Selection (JP3) JP3 Function 1-2 +12V 2-3 +5V (Default) 2.10 COM2 Ring/+5V/+12V Selection (JP4) JP4 Function 1-2 +12V 3-4 +5V 5-6 Ring (Default) 2.
SubCompact Board GENE-U15B 2.12 CPLD Reset Selection (JP6) JP6 Function 1-2 CPLD Reset Open Normal (Default) 2.13 Auto Power Button / Front Panel Button Selection (JP7) JP7 Function 1-2 Auto power button (Default) 2-3 Front panel button 2.14 CMOS Selection (JP8) JP8 Function 1-2 Protected (Default) 2-3 Clear 2.15 CRT Always On Disable/ Enable (JP9) JP9 Function 1-2 Disable (Default) 2-3 Enable 2.
SubCompact Board GENE-U15B 11 LA_DATA#_1 12 LA_DATA_1 13 LA_DATA#_2 14 LA_DATA_2 15 LA_DATA#_3 16 LA_DATA_3 17 L_DDC_DATA 18 L_DDC_CLK 19 LB_DATA#_0 20 LB_DATA_0 21 LB_DATA#_1 22 LB_DATA_1 23 LB_DATA#_2 24 LB_DATA_2 25 LB_DATA#_3 26 LB_DATA_3 27 VLCD 28 GND 29 LB_CLK# 30 LB_CLK 2.17 LVDS Inverter +5V/+12V Connector (CN6) Pin Signal 1 VCC-Inverter 2 BKL_CON 3 GND 4 GND 5 INV_EN 2.
SubCompact Board 8 X- 9 X+ GENE-U15B 2.19 RS-232 Serial Port Connector (CN11) Pin Signal 1 DCDA 2 RXA 3 TXA 4 DTRA 5 GNDA 6 DSRA 7 RTSA 8 CTSA 9 RIA 2.
SubCompact Board GENE-U15B 2.21 Fan Connector (CN17) Pin Signal 1 GND 2 +12V 3 Speed Sense 2.22 RS-232 Serial Port Connector (CN18) Pin Signal 1 DCDC 2 DSRC 3 RXC 4 RTSC 5 TXC 6 CTSC 7 DTRC 8 RIC 9 GND 2.23 PS2 Keyboard/Mouse Connector (CN19) Pin Signal Pin Signal 1 KBDAT 2 KBCLK 3 KB_GND 4 +5V_DUAL 5 MSDAT 6 MSCLK 2.
SubCompact Board 2 DSRD 3 RXD 4 RTSD 5 TXD 6 CTSD 7 DTRD 8 RID 9 GND GENE-U15B 2.25 CPLD Programming Connector (CN21) Pin Signal Pin Signal 1 TCK 2 GND 3 TDO 4 +3.3V_CPLD 5 TMS 6 NC 7 NC 8 NC 9 TDI 10 GND 2.26 12V Power Jack Connector (CN27) Pin Signal 1 +12V_DUAL 2 GND 2.
SubCompact Board 5 PS_ON# 6 +5V_DUAL GENE-U15B 2.28 Front Panel Connector (CN29) Pin Signal Pin Signal 1 Power On Button(-) 2 Power On Button(+) 3 IDE LED(-) 4 IDE LED(+) 5 External Buzzer(-) 6 External Buzzer(+) 7 Power LED(-) 8 Power LED(+) 9 Reset Switch(-) 10 Reset Switch(+) 2.29 USB Connector (CN30) Pin Signal Pin Signal 1 +5V_DUAL 2 GND 3 USBD4- 4 GND 5 USBD4+ 6 USBD5+ 7 GND 8 USBD5- 9 GND 10 +5V_DUAL 2.
SubCompact Board GENE-U15B 7 DIO_P#7 8 DIO_P#8 9 +3.
SubCompact Board GENE-U15B 2.33 Output Power Connector (CN36) Pin Signal 1 +5V 2 GND 2.34 Audio 2.1 Channel Connector (CN37) Pin Signal 1 MIC_L 2 MIC_R 3 GNDAUD 4 LIN_L 5 LIN_R 6 GNDAUD 7 LOUT_L 8 GNDAUD 9 LOUT_R 10 VCCAUD 2.35 LPC Connector (CN39) Pin Signal 1 LPC_AD0 2 LPC_AD0 3 LPC_AD0 4 LPC_AD0 5 +3.
SubCompact Board 9 LPC_CON_CLK33 10 NC 11 NC 12 INT_SERIRQ GENE-U15B 2.36 VGA Display Connector (CN40) Pin Signal Pin Signal 1 RED 2 GREEN 3 BLUE 4 N.C 5 GND 6 GND 7 GND 8 GND 9 +5V 10 GND 11 N.C 12 DDCDAT 13 HSYNC 14 VSYNC 15 DDCCLK 2.
SubCompact Board GENE-U15B Below Table for China RoHS Requirements 产品中有毒有害物质或元素名称及含量 AAEON Main Board/ Daughter Board/ Backplane 有毒有害物质或元素 部件名称 铅 汞 镉 六价铬 多溴联苯 多溴二苯醚 (Pb) (Hg) (Cd) (Cr(VI)) (PBB) (PBDE) × ○ ○ ○ ○ ○ × ○ ○ ○ ○ ○ 印刷电路板 及其电子组件 外部信号 连接器及线材 O：表示该有毒有害物质在该部件所有均质材料中的含量均在 SJ/T 11363-2006 标准规定的限量要求以下。 X：表示该有毒有害物质至少在该部件的某一均质材料中的含量超出 SJ/T 11363-2006 标准规定的限量要求。 备注：此产品所标示之环保使用期限，系指在一般正常使用状况下。 Chapter 2 Quick Installation Guide 2-20
SubCompact Board GENE-U15B Chapter 3 Award BIOS Setup Chapter 3 Award BIOS Setup 3-1
SubCompact Board 3.1 GENE-U15B System Test and Initialization These routines test and initialize board hardware. If the routines encounter an error during the tests, you will either hear a few short beeps or see an error message on the screen. There are two kinds of errors: fatal and non-fatal. The system can usually continue the boot up sequence with non-fatal errors.
SubCompact Board 3.2 GENE-U15B Award BIOS Setup Awards BIOS ROM has a built-in Setup program that allows users to modify the basic system configuration. This type of information is stored in battery-backed CMOS RAM so that it retains the Setup information when the power is turned off. Entering Setup Power on the computer and press immediately. This will allow you to enter Setup. Standard CMOS Features Use this menu for basic system configuration. (Date, time, IDE, etc.
SubCompact Board GENE-U15B PC Health Status This menu allows you to set the shutdown temperature for your system. Frequency/Voltage Control Use this menu to specify your settings for auto detect DIMM/PCI clock and spread spectrum. Load Fail-Safe Defaults Use this menu to load the BIOS default values for the minimal/stable performance for your system to operate. Load Optimized Defaults Use this menu to load the BIOS default values that are factory settings for optimal performance system operations.
SubCompact Board GENE-U15B Chapter 4 Driver Installation .
SubCompact Board GENE-U15B The GENE-U15B comes with an AutoRun CD-ROM that contains all drivers and utilities that can help you to install the driver automatically. Insert the driver CD, the driver CD-title will auto start and show the installation guide. If not, please follow the sequence below to install the drivers.
SubCompact Board 4.1 GENE-U15B Installation: Insert the GENE-U15B CD-ROM into the CD-ROM Drive. And install the drivers from Step 1 to Step 5 in order. Step 1 – Install Chipset Driver 1. Click on the STEP1-CHIPSET folder and select the folder of OS your system is 2. Double click on the infinst_autol.exe located in each OS folder 3. Follow the instructions that the window shows 4. The system will help you install the driver automatically Step 2 – Install VGA Driver 1.
SubCompact Board GENE-U15B 3. Follow the instructions that the window shows 4. The system will help you install the driver automatically Step 4 – Install Audio Driver 1. Click on the STEP4-AUDIO folder and select the folder of OS your system is 2. Double click on the Setup.exe located in each OS folder 3. Follow the instructions that the window shows 4. The system will help you install the driver automatically Note: 1. The default output of GMA500 driver is LVDS.
SubCompact Board GENE-U15B Appendix A Programming the Watchdog Timer Appendix A Programming the Watchdog Timer A-1
SubCompact Board GENE-U15B A.1 Programming GENE-U15B utilizes SCH3114-NU chipset as its watchdog timer controller. The SCH311X WDT ( Watch Dog Timer ) has a programmable time-out ranging from 1 to 255 minutes with one minute resolution, or 1 to 255 second resolution. The unit of the WDT timeout value are selected via bit[7] of the WDT_TIMEOUT register. The WDT time-out value is set through the WDT_VAL Runtime register.
SubCompact Board GENE-U15B Appendix A Programming the Watchdog Timer A-3
SubCompact Board GENE-U15B The following is a sample code to set WDT for 3 seconds. ;Runtime register I/O base address SUPERIO_GPIO_PORT .MODEL EQU 800h SMALL .
SubCompact Board GENE-U15B Appendix B I/O Information Appendix B I/O Information B - 1
SubCompact Board B.
SubCompact Board GENE-U15B B.
SubCompact Board B.3 IRQ Mapping Chart B.
SubCompact Board GENE-U15B Appendix C Mating Connecotor Appendix C Mating Connector C - 1
SubCompact Board GENE-U15B C.1 List of Mating Connectors and Cables The table notes mating connectors and available cables. Connector Function Label Mating Connector Vendor External +5VSB Power Input and PS_ON# LVDS Connector LVDS Inverter Connector RJ-45 Ethernet#1 Connector HIROSE CN12 Model no. Available Cable P/N Cable ATX Cable 170220020B DF13-30DS-1.
SubCompact Board CN31 CN32 CN34 Digital I/O Connector +5V Vin Connector USB Port 1 &2 Connector Neltron CATCH GENE-U15B 2026B-10 2.00mm Pitch 10 pins ( CATCH H754-2x5 or compatible) N/A N/A Power Cable N/A USB Cable 1709100201 USB Cable 1709100201 2 Pins For SATA Power 1702150155 2.
SubCompact Board GENE-U15B Appendix D DIO Appendix D DIO D-1
SubCompact Board GENE-U15B D.1 DIO The F75111 provides one serial access interface, I2C Bus, to read/write internal registers. The address of Serial Bus is 0x6E (0110_1110) The related register for configuring DIO is list as follows: Configuration and Control Register – Index 01h Power-on default [7:0]=0000_1000b Bit Name R/W PWR Description 7 INIT R/W VSB3V Software reset for all registers including Test Mode registers. Users use only.
SubCompact Board GENE-U15B Bit Name R/W PWR Description 7 GP27_OCTRL R/W VSB3V 6 GP26_OCTRL R/W VSB3V 5 GP25_OCTRL R/W VSB3V 4 GP24_OCTRL R/W VSB3V 3 GP23_OCTRL R/W VSB3V 2 GP22_OCTRL R/W VSB3V 1 GP21_OCTRL R/W VSB3V 0 GP20_OCTRL R/W VSB3V GPIO 27 output control. Set to 1 for output function. Set to 0 for input function (default). GPIO 26 output control. Set to 1 for output function. Set to 0 for input function (default). GPIO 25 output control.
SubCompact Board GENE-U15B Bit Name R/W PWR Description 7 6 5 4 3 2 1 0 GP27_PSTS GP26_PSTS GP25_PSTS GP24_PSTS GP23_PSTS GP22_PSTS GP21_PSTS GP20_PSTS RO RO RO RO RO RO RO RO VSB3V VSB3V VSB3V VSB3V VSB3V VSB3V VSB3V VSB3V Read the GPIO27 data on the pin. Read the GPIO26 data on the pin. Read the GPIO25 data on the pin. Read the GPIO24 data on the pin. Read the GPIO23 data on the pin. Read the GPIO22 data on the pin. Read the GPIO21 data on the pin. Read the GPIO20 data on the pin.
SubCompact Board GENE-U15B ;Input : CL - register index ; CH - device ID ;Output : AL - Value read Ct_I2CReadByte Proc Near mov ch,06eh mov dx, 500h + 00h xor al, al out dx, al call ; Host Control Register ; Clear previous commands Delay5ms mov dx, 500h + 04h ; Transmit Slave Address Register inc ch ; Set the slave address and mov al, ch ; prepare for a READ command out dx, al mov dx, 500h + 05h ; Host Command mov al, cl ; offset to read Register out dx, al mov dx, 500h + 0
SubCompact Board xor al, al out dx, al GENE-U15B ; Clear old data mov dx, 500h + 01h ; Host Status Register mov al, 07h out ; Clear all status bits dx, al mov dx, 500h + 00h mov al, 12h ; Start a byte access out call dx, al CT_Chk_SMBus_Ready mov in dx, 500h + 06h al, dx ret Ct_I2CReadByte Endp ;Input : CL - register index ; CH - device ID ; AL - Value to write ;Output: none Ct_I2CWriteByte Proc Near mov ch,06eh Appendix D DIO D-6 ; Host Control Reegister
SubCompact Board GENE-U15B xchg ah, al mov dx, 500h + 00h xor al, al out dx, al call mov ; Host Control Register ; Clear previous commands Delay5ms dx, 500h + 04h ; Transmit Slave Address Register mov al, ch out ; Set the slave address and dx, al ; prepare for a WRITE command mov dx, 500h + 05h ; Host Command mov al, cl ; offset to write Register out dx, al mov dx, 500h + 06h mov al, ah out dx, al mov dx, 500h + 01h ; Host Status Register mov al, 07h out ; Clear all statu
SubCompact Board GENE-U15B mov dx, 500h + 00h mov al, 12h ; Start a byte access out call ; Host Control Register dx, al CT_Chk_SMBus_Ready ;R14 ret Ct_I2CWriteByte Endp ; Wait until the busy bit clears, indicating that the SMBUS ; activity has concluded.
SubCompact Board test GENE-U15B al, 07h ; HSTS[2:0]=All clearable status bits jz Check_I2C_ByteRead_ForStatus ret CT_Chk_SMBus_Ready Endp END begin Appendix D DIO D-9
