Half-size SBC HSB-800I HSB-800I AMD LX800 Processor ISA Half-size CPU Card With DDR, Ethernet, CompactFlash™ & PC/104 HSB-800I Manual Rev. A 3rd Ed.
Half-size CPU Card HSB-800I Copyright Notice This document is copyrighted, 2008. All rights are reserved. The original manufacturer reserves the right to make improvements to the products described in this manual at any time without notice. No part of this manual may be reproduced, copied, translated, or transmitted in any form or by any means without the prior written permission of the original manufacturer. Information provided in this manual is intended to be accurate and reliable.
Half-size CPU Card HSB-800I Acknowledgments All other products’ name or trademarks are properties of their respective owners. Award is a trademark of Award Software International, Inc. CompactFlash™ is a trademark of the Compact Flash Association. AMD, the AMD Arrow logo and combinations thereof are trademarks of Advanced Micro Devices, Inc. ® Microsoft Windows is a registered trademark of Microsoft Corp. ITE is a trademark of Integrated Technology Express, Inc.
Half-size CPU Card HSB-800I Packing List Before you begin installing HSB-800I, please make sure that the following items have been shipped: • 1701340704 Flat Cable • 1701400453 ATA-100 Cable • 1700060192 PS/2 Keyboard & Mouse Cable • 1709140302 Cable • 1701200301 Flat Cable • 170910020A USB Cable • 1703030501 Wire • 1701010302 Flat Cable • HSB-800I CPU Card • Quick Installation Guide • CD-ROM for manual (in PDF format) and drivers If any of these items are missing or damaged,
Half-size CPU Card HSB-800I Contents Chapter 1 General Information 1.1 Introduction................................................................ 1-2 1.2 Feature ...................................................................... 1-3 1.3 Specification .............................................................. 1-4 Chapter 2 Quick Installation Guide 2.1 Safety Precaution ...................................................... 2-2 2.2 Location of Connectors and Jumpers ....................... 2-3 2.
Half-size CPU Card HSB-800I 2.17 Digital I/O (CN1) ...................................................... 2-11 2.18 LPT Port Connector (LPT1) .................................... 2-12 2.19 USB Connector (USB1~3) ...................................... 2-12 2.20 FAN Connector (CN2) ............................................. 2-13 2.21 Audio Input/ Output/ CD-in/ MIC (CN3)................... 2-13 2.22 LCD Inverter (CN4) ................................................. 2-13 2.23 TFT LCD (CN5) .............
Half-size CPU Card HSB-800I B.3 IRQ Mapping Chart ................................................B-3 B.4 DMA Channel Assignments...................................
Half-size SBC HSB-800I Chapter 1 General Information Chapter 1 General Information 1-1
Half-size SBC HSB-800I 1.1 Introduction AAEON releases the economic half-size Single Board Computer (SBC) – HSB-800I, which is designed to target the industrial control and automation market. HSB-800I is based on AMD LX800 processor, which features the low power consumption and faster heat spreading to ensure the performance of the product. HSB-800I supports onboard DDR400 system memory up to 128MB and the chipset of HSB-800I is AMDLX800 +CS5536.
Half-size SBC HSB-800I 1.2 Features AMD LX 800 Processor Onboard 128MB DDR 400 Memory Integrated 2D/3D Graphics Accelerator, VGA Support CRT/TFT 10/100/1000Base-TX Ethernet x 1 (10/100 & GbE Optional) USB2.0 x 4/ RS-232 x 3, RS-232/422/485 x 1/ Parallel x 1/ IrDA Port x 1 Ultra ATA 33 x 1 Digital I/O AC97 PC/104 CompactFlash Type II Socket Watchdog Function 1~255 Sec.
Half-size SBC HSB-800I 1.
Half-size SBC HSB-800I Display: Supports CRT and LCD Simultaneous Display VGA Controller AMD LX800 Memory Shared memory up to 16M Resolutions 1600x1200 @ 32bpp at 100MHz for CRT; 1600x1200 @ 24bpp for LCD LCD Interface Up to 24-bit, LVDS/TTL LCD support I/O: CS5536 Serial Port COM x 4 (Internal Pin Header x 4) COM1, COM3, COM4: RS-232 COM2: RS-232/422/485 Parallel Port Supports SPP/EPP/ECP mode Universal Serial Bus USB2.
Half-size SBC HSB-800I Chapter 2 Quick Installation Guide Chapter 2 Quick Installation Guide 2-1
Half-size SBC HSB-800I 2.1 Safety Precautions Always completely disconnect the power cord from your board whenever you are working on it. Do not make connections while the power is on, because a sudden rush of power can damage sensitive electronic components. Always ground yourself to remove any static charge before touching the board. Modern electronic devices are very sensitive to static electric charges. Use a grounding wrist strap at all times.
Half-size SBC HSB-800I 2.
Half-size SBC 2.
Half-size SBC HSB-800I Solder Side 86.5 72.37 157.38 106.91 19.94 21.
Half-size SBC HSB-800I 2.4 List of Jumpers The board has a number of jumpers that allow you to configure your system to suit your application. The table below shows the function of each of the board's jumpers: Label Function JP1 CFD Voltage 3.3V/ 5V Selection JP2 Clear CMOS JP3 AT/ATX Power Type Selection JP4 LCD Clock and Power Selection JP5 Inverter Voltage Selection 2.5 List of Connectors The board has a number of connectors that allow you to configure your system to suit your application.
Half-size SBC HSB-800I IR1 IrDA Connector LPT1 LPT Port Connector USB1~3 USB Connector USB4 DIMM1 USB Connector 10/100 or 100/1000 Base-TX Ethernet Connector DDRII SODIMM Slot (Optional) CN1 Digital I/O CN2 Fan Connector CN3 Audio Input/Output/CDin/MIC CN4 LCD Inverter Power Connector CN5 TFT LCD Connector CN6 +5VSB Power Connector CN7 AT Power_5V,12V Connector CN8 PC/104 ISA Interface CN9 LVDS1 Connector CN10 LVDS2 Connector CN11 PS2 Keyboard/Mouse Connector CN12 Internal
Half-size SBC HSB-800I 2.6 Setting Jumpers You configure your card to match the needs of your application by setting jumpers. A jumper is the simplest kind of electric switch. It consists of two metal pins and a small metal clip (often protected by a plastic cover) that slides over the pins to connect them. To “close” a jumper you connect the pins with the clip. To “open” a jumper you remove the clip. Sometimes a jumper will have three pins, labeled 1, 2 and 3.
Half-size SBC HSB-800I 2.7 CFD Voltage 3.3V/5V Selection (JP1) JP1 Function 1-2 3.3V (default) 2-3 5V 2.8 Clear CMOS (JP2) JP2 Function 1-2 Normal (default) 2-3 Clear CMOS 2.9 AT/ATX Power Type Selection (JP3) JP3 Function 1-2 ATX Power Supply (default) Open AT Power Supply Note: Only AT Function w/o Backplanes. 2.10 LCD Clock and Power Selection (JP4) JP4 Function 1-3 Normal (default) 3-5 Inverse 2-4 +5Vlcd 4-6 +3Vlcd (default) 2.
Half-size SBC HSB-800I 2.12 Front Panel Connector (FP1) Pin Signal Pin Signal 1 Power On Button (+) 2 Reset Switch (+) 3 Power On Button (-) 4 Reset Switch (-) 5 IDE LED (+) 6 Power LED (+) 7 IDE LED (-) 8 Power LED (-) 2.13 Front Panel Connector (FP2) Note: Internal Buzzer enable: Close Pin 5,7 Pin Signal Pin Signal 1 External Speaker (+) 2 Key Board Lock (+) 3 NC 4 GND 5 Internal Buzzer (-) 6 I2C Bus SMB Clock 7 External Speaker (-) 8 I2C Bus SMB Data 2.
Half-size SBC HSB-800I 2.15 RS-232/422/485 Serial Port Connector (COM2) Pin Signal Pin Signal 1 DCD (422TXD-/485DATA-) 2 RXD (422RXD+) 3 TXD (422TXD+/485DATA+) 4 DTR (422RXD-) 5 GND 6 DSR 7 RTS 8 CTS 9 RI 10 NC 2.16 IrDA Connector (IR1) Pin Signal 1 +5V 2 NC 3 IRRX 4 GND 5 IRTX 6 NC 2.
Half-size SBC HSB-800I 2.18 LPT Port Connector (LPT1) Pin Signal Pin Signal 1 #STROBE 2 #AFD 3 DATA0 4 #ERROR 5 DATA1 6 #INIT 7 DATA2 8 #SLIN 9 DATA3 10 GND 11 DATA4 12 GND 13 DATA5 14 GND 15 DATA6 16 GND 17 DATA7 18 GND 19 #ACK 20 GND 21 BUSY 22 GND 23 PE 24 GND 25 SELECT 26 GND 2.
Half-size SBC HSB-800I 2.20 FAN Connector (CN2) Pin Signal 1 GND 2 +5V 3 Speed Sense 2.21 Audio Input/ Output/ CD-in/ MIC (CN3) Pin Signal Pin Signal 1 MIC 2 MIC_Vcc 3 Audio Ground 4 CD_GND 5 LINE_IN L 6 CD_L 7 LINE_IN R 8 CD_GND 9 Audio Ground 10 CD_R 11 LINE_OUT L 12 LINE_OUT R 13 Audio Ground 14 Audio Ground 2.
Half-size SBC HSB-800I 2.23 TFT LCD (CN5) For 24-bit TFT LCD Pin Signal Pin Signal 1 +5VLCD 2 +5VLCD 3 GND 4 GND 5 +3.3VLCD 6 +3.
Half-size SBC HSB-800I For 18-bit TFT LCD Pin Signal Pin Signal 1 +5VLCD 2 +5VLCD 3 GND 4 GND 5 +3.3VLCD 6 +3.
Half-size SBC HSB-800I 2.24 +5VSB Power Connector (CN6) Pin Signal 1 PS_ON# 2 +5V 3 +5VSB 2.25 AT Power_5V, 12V Connector (CN7) Pin Signal 1 +5V 2 GND 3 GND 4 +12V 2.
Half-size SBC HSB-800I 23 NC 24 NC 25 NC 26 NC 27 VLCD 28 GND 29 NC 30 NC 2.27 PS2 Keyboard/ Mouse Connector (CN11) Pin Signal 1 KB_DATA 2 MS-DATA 3 GND 4 +5V 5 KB_CLK 6 MS_CLK 2.
Half-size SBC HSB-800I Below Table for China RoHS Requirements 产品中有毒有害物质或元素名称及含量 AAEON Main Board/ Daughter Board/ Backplane 有毒有害物质或元素 部件名称 铅 汞 镉 六价铬 多溴联苯 多溴二苯醚 (Pb) (Hg) (Cd) (Cr(VI)) (PBB) (PBDE) × ○ ○ ○ ○ ○ × ○ ○ ○ ○ ○ 印刷电路板 及其电子组件 外部信号 连接器及线材 O：表示该有毒有害物质在该部件所有均质材料中的含量均在 SJ/T 11363-2006 标准规定的限量要求以下。 X：表示该有毒有害物质至少在该部件的某一均质材料中的含量超出 SJ/T 11363-2006 标准规定的限量要求。 备注：此产品所标示之环保使用期限，系指在一般正常使用状况下。 Chapter 2 Quick Installation Guide 2-18
Half-size SBC HSB-800I Chapter 3 Award BIOS Setup Chapter 3 Award BIOS Setup 3-1
Half-size SBC HSB-800I 3.1 System Test and Initialization These routines test and initialize board hardware. If the routines encounter an error during the tests, you will either hear a few short beeps or see an error message on the screen. There are two kinds of errors: fatal and non-fatal. The system can usually continue the boot up sequence with non-fatal errors.
Half-size SBC HSB-800I 3.2 Award BIOS Setup Awards BIOS ROM has a built-in Setup program that allows users to modify the basic system configuration. This type of information is stored in battery-backed CMOS RAM so that it retains the Setup information when the power is turned off. Entering setup Power on the computer and press immediately. This will allow you to enter Setup. Standard CMOS Features Use this menu for basic system configuration. (Date, time, IDE, etc.
Half-size SBC HSB-800I PC Health Status This menu shows you the status of PC. Frequency/Voltage Control This menu shows you the display of frequency/Voltage Control. Load Fail-Safe Defaults Use this menu to load the BIOS default values for the minimal/ stable performance for your system to operate. Load Optimized Defaults Use this menu to load the BIOS default values that are factory settings for optimal performance system operations.
Half-size SBC HSB-800I Chapter 4 Driver Installation Chapter 4 Driver Installation 4-1
Half-size SBC HSB-800I The HSB-800I comes with a CD-ROM that contains all drivers your need. Follow the sequence below to install the drivers: Step 1 – Install LX-Graphics Driver Step 2 – Install AES Driver Step 3 – Install PCI to ISA Bridge Driver Step 4 – Install LAN Driver Step 5 – Install Audio Driver Please read following instructions for detailed installations.
Half-size SBC HSB-800I 4.1 Installation: Insert the HSB-800I CD-ROM into the CD-ROM Drive. And install the drivers from Step 1 to Step 5 in order. Step 1 –Install LX-Graphic Driver Place the Driver CD-ROM into your CD-ROM drive and follow the steps below to install. 1. Click on Start button 2. Click on Settings button 3. Click on Control Panel button 4. Click on System button 5. Select Hardware and click on Device Manager… 6. Double click on Video Controller (VGA Compatible) 7. Click on Update Driver… 8.
Half-size SBC HSB-800I Step 2 –Install AES Driver Place the Driver CD-ROM into your CD-ROM drive and follow the steps below to install. 1. Click on Start button 2. Click on Settings button 3. Click on Control Panel button 4. Click on System button 5. Select Hardware and click on Device Manager… 6. Double click on Entertainment Encryption/Decryption Controller 7. Click on Update Driver… 8. Click on Next 9. Select Search for a suitable driver…, then click on Next 10.
Half-size SBC HSB-800I 3. Click on Control Panel button 4. Click on System button 5. Select Hardware and click on Device Manager… 6. Double click on Other PCI Bridge Device 7. Click on Update Driver… 8. Click on Next 9. Select Search for a suitable driver…, then click on Next 10. Select Specify a location, then click on Next 11. Click on Browse 12. Select “Ite” file from CD-ROM (Drivers/Step 3- PCI to ISA Bridge ) then click on open 13. Click on OK 14. Click on Next 15. Click on Yes 16.
Half-size SBC HSB-800I Step 5– Install Audio Driver Place the Driver CD-ROM into your CD-ROM drive and follow the steps below to install. 1. Click on Start button 2. Click on Settings button 3. Click on Control Panel button 4. Click on System button 5. Select Hardware and click on Device Manager… 6. Double click on Multimedia Audio Controller 7. Click on Update Driver… 8. Click on Next 9. Select Search for a suitable driver…, then click on Next 10. Select Specify a location, then click on Next 11.
Half-size SBC HSB-800I Appendix A Programming the Watchdog Timer Appendix A Programming the Watchdog Timer A - 1
Half-size SBC HSB-800I A.1 Programming HSB-800I utilizes ITE 8712 chipset as its watchdog timer controller. ( K version ) Below are the procedures to complete its configuration and the AAEON intial watchdog timer program is also attached based on which you can develop customized program to fit your application. Configuring Sequence Description After the hardware reset or power-on reset, the ITE 8712 enters the normal mode with all logical devices disabled except KBC.
Half-size SBC HSB-800I There are three steps to complete the configuration setup: (1) Enter the MB PnP Mode; (2) Modify the data of configuration registers; (3) Exit the MB PnP Mode. Undesired result may occur if the MB PnP Mode is not exited normally. (1) Enter the MB PnP Mode To enter the MB PnP Mode, four special I/O write operations are to be performed during Wait for Key state.
Half-size SBC HSB-800I Configure Control (Index=02h) This register is write only. Its values are not sticky; that is to say, a hardware reset will automatically clear the bits, and does not require the software to clear them. Bit 7-2 1 0 Description Reserved Returns to the Wait for Key state. This bit is used when the configuration sequence is completed. Resets all logical devices and restores configuration registers to their power-on states.
Half-size SBC 4 3 HSB-800I WDT output through PWROK1/PWROK2 (pulse) enable Select the interrupt levelnote for WDT WatchDog Timer Time-out Value (LSB) Register (Index=73h, Default=00h) Bit 7-0 Description WDT Time-out value 7-0 WatchDog Timer Time-out Value (MSB) Register (Index=74h, Default=00h) Bit 7-0 Description WDT Time-out value 15-8 A.2 ITE8712 Watchdog Timer Initial Program .MODEL SMALL .
Half-size SBC HSB-800I Watch_Dog_Setting: ;Timer setting mov al, cl mov cl, 73h call Superio_Set_Reg ;Clear by keyboard or mouse interrupt mov al, 0f0h mov cl, 71h call Superio_Set_Reg ;unit is second.
Half-size SBC HSB-800I MOV DX,02Eh MOV CX,04h Init_1: MOV AL,BYTE PTR CS:[SI] OUT DX,AL INC SI LOOP Init_1 RET Enter_Configuration_Mode ENDP Exit_Configuration_Mode PROC NEAR MOV AX,0202h CALL Write_Configuration_Data RET Exit_Configuration_Mode ENDP Check_Chip PROC NEAR MOV AL,20h CALL Read_Configuration_Data CMP AL,87h JNE Not_Initial MOV AL,21h CALL Read_Configuration_Data Appendix A Programming the Watchdog Timer A - 7
Half-size SBC HSB-800I CMP AL,12h JNE Not_Initial Need_Initial: STC RET Not_Initial: CLC RET Check_Chip ENDP Read_Configuration_Data PROC NEAR MOV DX,WORD PTR CS:[Cfg_Port+04h] OUT DX,AL MOV DX,WORD PTR CS:[Cfg_Port+06h] IN AL,DX RET Read_Configuration_Data ENDP Write_Configuration_Data PROC NEAR MOV DX,WORD PTR CS:[Cfg_Port+04h] OUT DX,AL XCHG AL,AH MOV DX,WORD PTR CS:[Cfg_Port+06h] OUT DX,AL RET Appendix A Programming the Watchdog Timer A - 8
Half-size SBC HSB-800I Write_Configuration_Data ENDP Superio_Set_Reg proc near push ax MOV DX,WORD PTR CS:[Cfg_Port+04h] mov al,cl out dx,al pop ax inc dx out dx,al ret Superio_Set_Reg endp.
Half-size SBC HSB-800I Cfg_Port DB 087h,001h,055h,055h DW 02Eh,02Fh END Main Note: Interrupt level mapping 0Fh-Dh: not valid 0Ch: IRQ12 . .
Half-size SBC HSB-800I Appendix B I/O Information Appendix B I/O Information B-1
Half-size SBC B.
Half-size SBC HSB-800I B.2 Memory Address Map B.3 IRQ Mapping Chart B.
