Half-size SBC HSB-800P HSB-800P AMD LX800 Processor PCI Half-size CPU Card With DDR, Ethernet, CompactFlash™ & 4 COM Ports & 4 USB HSB-800P Manual Rev. A 3rd Ed.
Half-size CPU Card HSB-800P Copyright Notice This document is copyrighted, 2010. All rights are reserved. The original manufacturer reserves the right to make improvements to the products described in this manual at any time without notice. No part of this manual may be reproduced, copied, translated, or transmitted in any form or by any means without the prior written permission of the original manufacturer. Information provided in this manual is intended to be accurate and reliable.
Half-size CPU Card HSB-800P Acknowledgments All other products’ name or trademarks are properties of their respective owners. Award is a trademark of Award Software International, Inc. CompactFlash™ is a trademark of the Compact Flash Association. AMD, the AMD Arrow logo and combinations thereof are trademarks of Advanced Micro Devices, Inc. ® Microsoft Windows is a registered trademark of Microsoft Corp. ITE is a trademark of Integrated Technology Express, Inc.
Half-size CPU Card HSB-800P Packing List Before you begin installing HSB-800P, please make sure that the following items have been shipped: 1701340704 Flat Cable.34P.70cm.GRAY for FDD 1701400453 Cable.40P 2.54mm IDC W/Nose W/Fold.40P 2.54mm IDC W/Nose W/Fold.45cm.Blue ATA-100 1700060192 Cable.6P-6P-6P.19cm.IVORY PS2/KB&Mouse 1703030501 Wire.3P 2.5mm Housing.3P 2.5mm Housing.50cm 1701260307 Flat Cable.9P/DB9P MALE&25P DB25P FEMALE.10P 2mm&26P 2mm/IDC NO FOLD.30cm.W/BKT.
Half-size CPU Card HSB-800P Contents Chapter 1 General Information 1.1 Introduction................................................................ 1-2 1.2 Feature ...................................................................... 1-3 1.3 Specification .............................................................. 1-4 Chapter 2 Quick Installation Guide 2.1 Safety Precaution ...................................................... 2-2 2.2 Location of Connectors and Jumpers ....................... 2-3 2.
Half-size CPU Card HSB-800P 2.17 Digital I/O (CN1) ...................................................... 2-11 2.18 LPT Port Connector (LPT1) .................................... 2-12 2.19 USB Connector (USB1~2) ...................................... 2-12 2.20 FAN Connector (CN2) ............................................. 2-13 2.21 Audio Input/ Output (CN3)....................................... 2-13 2.22 AT Power_5V, 12V Connector (CN5) ..................... 2-13 2.23 LCD Inverter (CN6) ..............
Half-size CPU Card HSB-800P B.4 DMA Channel Assignments...................................B-3 Appendix C Mating Connector C.1 List of Mating Connectors and Cables..................
Half-size SBC HSB-800P Chapter 1 General Information Chapter 1 General Information 1-1
Half-size SBC HSB-800P 1.1 Introduction AAEON releases the economic half-size Single Board Computer (SBC) – HSB-800P, which is designed to target the industrial control and automation market. HSB-800P is based on AMD LX800 processor, which features the low power consumption and faster heat spreading to ensure the performance of the product. HSB-800P supports onboard DDR400 system memory up to 256MB and the chipset of HSB-800P is AMDLX800 +CS5536.
Half-size SBC HSB-800P 1.2 Features Ultra Low Voltage CPU Power Consumption CPU Clock 500 MHz Onboard 256MB DDR400 Memory Integrated 2D Graphics Accelerator, VGA Support Supports CRT/LVDS 10/100 Base-TX Ethernet x 1 Ultra ATA100 x 1; SATA I x 2 USB2.
Half-size SBC HSB-800P 1.
Half-size SBC HSB-800P Display: Supports CRT and LCD Simultaneous Display Chipset LX800 LCD Interface Up to 24-bit, LVDS LCD Support Memory Shared memory up to 16M Resolution 1600 x 1200@32bpp at 100MHz for CRT 1024 x 768@24bpp for LVDS I/O: CS5536 Serial Port COM Port x 4 (Internal Pin Header x 3; Rear I/O x 1); COM 1(Rear I/O), COM 3, COM 4: RS-232; COM 2: RS-232/422/485 KB & Mouse Mini-Din PS/2, KB & Mouse Connector x 1 (Rear I/O); Internal keyboard Box header x 1 Universal Serial Bus USB x
Half-size SBC Digital I/O HSB-800P 8 bit digital I/O, 4 input/ 4 output by super I/O Parallel SPP/EPP/ECP mode Audio AC 97 codec daughter board (optional) LAN PCI 10/100Mb LAN x 1, RJ-45 x 1; Realtek 8100C controller (Rear I/O) Chapter 1 General Information 1-6
Half-size SBC HSB-800P Chapter 2 Quick Installation Guide Notice: The Quick Installation Guide is derived from Chapter 2 of the user manual. For other chapters and further installation instructions, please refer to the user manual CD-ROM that came with the product. Part No. 2007800P21 Printed in Taiwan Nov.
Half-size SBC HSB-800P 2.1 Safety Precautions Always completely disconnect the power cord from your board whenever you are working on it. Do not make connections while the power is on, because a sudden rush of power can damage sensitive electronic components. Always ground yourself to remove any static charge before touching the board. Modern electronic devices are very sensitive to static electric charges. Use a grounding wrist strap at all times.
Half-size SBC HSB-800P 2.
Half-size SBC Solder Side Chapter 2 Quick Installation Guide 2-4 HSB-800P
Half-size SBC HSB-800P 2.
Half-size SBC HSB-800P 2.4 List of Jumpers The board has a number of jumpers that allow you to configure your system to suit your application. The table below shows the function of each of the board's jumpers: Label Function JP1 CFD Voltage 3.
Half-size SBC HSB-800P 2.5 List of Connectors The board has a number of connectors that allow you to configure your system to suit your application.
Half-size SBC HSB-800P 2.6 Setting Jumpers You configure your card to match the needs of your application by setting jumpers. A jumper is the simplest kind of electric switch. It consists of two metal pins and a small metal clip (often protected by a plastic cover) that slides over the pins to connect them. To “close” a jumper you connect the pins with the clip. To “open” a jumper you remove the clip. Sometimes a jumper will have three pins, labeled 1, 2 and 3.
Half-size SBC HSB-800P 2.7 CFD Voltage 3.3V/5V Selection (JP1) JP1 Function 1-2 3.3V 2-3 5V (default) 2.8 LCD Clock and Power Selection (JP2) JP2 Function 1-3 Normal (default) 3-5 Inverse 2-4 +5Vlcd 4-6 +3Vlcd (default) 2.9 Inverter Voltage Selection (JP3) JP3 Function 1-2 +12V (default) 2-3 +5V 2.10 Clear CMOS (JP4) JP4 Function 1-2 Normal (default) 2-3 Clear CMOS 2.
Half-size SBC HSB-800P 2.12 Front Panel Connector (FP1) Pin Signal Pin Signal 1 Power On Button (+) 2 Reset Switch (+) 3 Power On Button (-) 4 Reset Switch (-) 5 IDE LED (+) 6 Power LED (+) 7 IDE LED (-) 8 Power LED (-) 2.13 Front Panel Connector (FP2) Pin Signal Pin Signal 1 External Speaker (+) 2 Key Board Lock (+) 3 N.
Half-size SBC HSB-800P 2.15 RS-232/422/485 Serial Port Connector (COM2) Pin Signal Pin Signal 1 DCD (422TXD-/485DATA-) 2 RXD (422RXD+) 3 TXD (422TXD+/485DATA+) 4 DTR (422RXD-) 5 GND 6 DSR 7 RTS 8 CTS 9 RI/+12V 10 N.C 2.16 IrDA Connector (IR1) Pin Signal 1 +5V 2 N.C 3 IRRX 4 GND 5 IRTX 6 N.C 2.
Half-size SBC HSB-800P DIO-2 CN1 Pin2 Bit6 U7 Pin21 DIO-3 CN1 Pin3 Bit5 U7 Pin22 DIO-4 CN1 Pin4 Bit4 U7 Pin23 DIO-5 CN1 Pin5 Bit3 U7 Pin24 DIO-6 CN1 Pin6 Bit2 U7 Pin25 DIO-7 CN1 Pin7 Bit1 U7 Pin26 DIO-8 CN1 Pin7 Bit0 U7 Pin27 2.
Half-size SBC HSB-800P 7 GND 8 USBD1- 9 GND 10 +5V 2.20 Fan Connector (CN2) Pin Signal 1 GND 2 +5V 3 Speed Sense 2.21 Audio Input/ Output (CN3) Pin Signal Pin Signal 1 AC_RST# 2 AC_SYNC 3 AC_SDIN0 4 AC_SDOUT 5 GND 6 AC_BITCLK 7 GND 8 +5V 9 N.C 10 +3.3V 2.22 AT Power_5V, 12V Connector (CN5) Pin Signal 1 +5V 2 GND 3 GND 4 +12V 2.
Half-size SBC 3 VCON 4 GND 5 BKL_EN HSB-800P 2.24 LVDS1 (CN7) Pin Signal Pin Signal 1 BKL_EN 2 N.C 3 VLCD 4 GND 5 LVDS_CLK# 6 LVDS_CLK 7 VLCD 8 GND 9 TX0# 10 TX0 11 TX1# 12 TX1 13 TX2# 14 TX2 15 TX3# 16 TX3 17 N.C 18 N.C 19 N.C 20 N.C 21 N.C 22 N.C 23 N.C 24 N.C 25 N.C 26 N.C 27 VLCD 28 GND 29 N.C 30 N.C 2.
Half-size SBC HSB-800P 2.26 Internal Keyboard Connector (CN9) Pin Signal 1 KB_CLK 2 KB_DATA 3 N.C 4 GND 5 +5V 2.
Half-size SBC HSB-800P Below Table for China RoHS Requirements 产品中有毒有害物质或元素名称及含量 AAEON Main Board/ Daughter Board/ Backplane 有毒有害物质或元素 部件名称 铅 汞 镉 六价铬 多溴联苯 多溴二苯醚 (Pb) (Hg) (Cd) (Cr(VI)) (PBB) (PBDE) × ○ ○ ○ ○ ○ × ○ ○ ○ ○ ○ 印刷电路板 及其电子组件 外部信号 连接器及线材 O：表示该有毒有害物质在该部件所有均质材料中的含量均在 SJ/T 11363-2006 标准规定的限量要求以下。 X：表示该有毒有害物质至少在该部件的某一均质材料中的含量超出 SJ/T 11363-2006 标准规定的限量要求。 备注：此产品所标示之环保使用期限，系指在一般正常使用状况下。 Chapter 2 Quick Installation Guide 2-16
Half-size SBC HSB-800P Chapter 3 Award BIOS Setup Chapter 3 Award BIOS Setup 3-1
Half-size SBC HSB-800P 3.1 System Test and Initialization These routines test and initialize board hardware. If the routines encounter an error during the tests, you will either hear a few short beeps or see an error message on the screen. There are two kinds of errors: fatal and non-fatal. The system can usually continue the boot up sequence with non-fatal errors.
Half-size SBC HSB-800P 3.2 Award BIOS Setup Awards BIOS ROM has a built-in Setup program that allows users to modify the basic system configuration. This type of information is stored in battery-backed CMOS RAM so that it retains the Setup information when the power is turned off. Entering setup Power on the computer and press immediately. This will allow you to enter Setup. Standard CMOS Features Use this menu for basic system configuration. (Date, time, IDE, etc.
Half-size SBC HSB-800P PC Health Status This menu shows you the status of PC. Load Fail-Safe Defaults Use this menu to load the BIOS default values for the minimal/ stable performance for your system to operate. Load Optimized Defaults Use this menu to load the BIOS default values that are factory settings for optimal performance system operations. While AWARD has designated the custom BIOS to maximize performance, the factory has the right to change these defaults to meet their needs.
Half-size SBC HSB-800P Chapter 4 Driver Installation Chapter 4 Driver Installation 4-1
Half-size SBC HSB-800P The HSB-800P comes with a CD-ROM that contains all drivers your need. Follow the sequence below to install the drivers: Step 1 – Install VGA Driver Step 2 – Install AES Driver Step 3 – Install LAN Driver Step 4 – Install Audio Driver Step 5 – Install SATA Driver Please read following instructions for detailed installations.
Half-size SBC HSB-800P 4.1 Installation: Insert the HSB-800P CD-ROM into the CD-ROM Drive. And install the drivers from Step 1 to Step 5 in order. Step 1 –Install VGA Driver Place the Driver CD-ROM into your CD-ROM drive and follow the steps below to install. 1. Click on Start button 2. Click on Settings button 3. Click on Control Panel button 4. Click on System button 5. Select Hardware and click on Device Manager… 6. Double click on Video Controller (VGA Compatible) 7. Click on Update Driver… 8.
Half-size SBC HSB-800P Step 2 –Install AES Driver Place the Driver CD-ROM into your CD-ROM drive and follow the steps below to install. 1. Click on Start button 2. Click on Settings button 3. Click on Control Panel button 4. Click on System button 5. Select Hardware and click on Device Manager… 6. Double click on Entertainment Encryption/Decryption Controller 7. Click on Update Driver… 8. Click on Next 9. Select Search for a suitable driver…, then click on Next 10.
Half-size SBC HSB-800P 2. Double click on Setup.exe 3. Follow the instructions that the window shows 4. The system will help you install the driver automatically Step 4– Install Audio Driver Place the Driver CD-ROM into your CD-ROM drive and follow the steps below to install. 1. Click on Start button 2. Click on Settings button 3. Click on Control Panel button 4. Click on System button 5. Select Hardware and click on Device Manager… 6. Double click on Multimedia Audio Controller 7.
Half-size SBC HSB-800P Step 5 – Install SATA Driver Place the Driver CD-ROM into your CD-ROM drive and pull up the CD-ROM file on your screen. 1. Click on Start button 2. Click on Settings button 3. Click on Control Panel button 4. Click on System button 5. Select Hardware and click on Device Manager… 6. Double click on SCSI and RAID Controller 7. Click on Update Driver… 8. Click on Next 9. Select Search for a suitable driver…, then click on Next 10. Select Specify a location, then click on Next 11.
Half-size SBC HSB-800P Appendix A Programming the Watchdog Timer Appendix A Programming the Watchdog Timer A - 1
Half-size SBC HSB-800P A.1 Programming HSB-800P utilizes ITE 8712 chipset as its watchdog timer controller. ( K version ) Below are the procedures to complete its configuration and the AAEON intial watchdog timer program is also attached based on which you can develop customized program to fit your application. Configuring Sequence Description After the hardware reset or power-on reset, the ITE 8712 enters the normal mode with all logical devices disabled except KBC.
Half-size SBC HSB-800P Exit the MB PnP Mode. Undesired result may occur if the MB PnP Mode is not exited normally. (1) Enter the MB PnP Mode To enter the MB PnP Mode, four special I/O write operations are to be performed during Wait for Key state. To ensure the initial state of the key-check logic, it is necessary to perform four write opera-tions to the Special Address port (2EH). Two different enter keys are provided to select configuration ports (2Eh/2Fh) of the next step.
Half-size SBC HSB-800P require the software to clear them. Bit 7-2 1 0 Description Reserved Returns to the Wait for Key state. This bit is used when the configuration sequence is completed. Resets all logical devices and restores configuration registers to their power-on states.
Half-size SBC HSB-800P WatchDog Timer Time-out Value (LSB) Register (Index=73h, Default=00h) Bit 7-0 Description WDT Time-out value 7-0 WatchDog Timer Time-out Value (MSB) Register (Index=74h, Default=00h) Bit 7-0 Description WDT Time-out value 15-8 Appendix A Programming the Watchdog Timer A - 5
Half-size SBC HSB-800P A.2 ITE8712 Watchdog Timer Initial Program .MODEL SMALL .CODE Main: CALL Enter_Configuration_mode CALL Check_Chip mov cl, 7 call Set_Logic_Device ;time setting mov cl, 10 ; 10 Sec dec al Watch_Dog_Setting: ;Timer setting mov al, cl mov cl, 73h call Superio_Set_Reg ;Clear by keyboard or mouse interrupt mov al, 0f0h mov cl, 71h call Superio_Set_Reg ;unit is second.
Half-size SBC HSB-800P ; game port enable mov cl, 9 call Set_Logic_Device Initial_OK: CALL Exit_Configuration_mode MOV AH,4Ch INT 21h Enter_Configuration_Mode PROC NEAR MOV SI,WORD PTR CS:[Offset Cfg_Port] MOV DX,02Eh MOV CX,04h Init_1: MOV AL,BYTE PTR CS:[SI] OUT DX,AL INC SI LOOP Init_1 RET Enter_Configuration_Mode ENDP Exit_Configuration_Mode PROC NEAR MOV AX,0202h CALL Write_Configuration_Data Appendix A Programming the Watchdog Timer A - 7
Half-size SBC HSB-800P RET Exit_Configuration_Mode ENDP Check_Chip PROC NEAR MOV AL,20h CALL Read_Configuration_Data CMP AL,87h JNE Not_Initial MOV AL,21h CALL Read_Configuration_Data CMP AL,12h JNE Not_Initial Need_Initial: STC RET Not_Initial: CLC RET Check_Chip ENDP Read_Configuration_Data PROC NEAR MOV DX,WORD PTR CS:[Cfg_Port+04h] OUT DX,AL Appendix A Programming the Watchdog Timer A - 8
Half-size SBC HSB-800P MOV DX,WORD PTR CS:[Cfg_Port+06h] IN AL,DX RET Read_Configuration_Data ENDP Write_Configuration_Data PROC NEAR MOV DX,WORD PTR CS:[Cfg_Port+04h] OUT DX,AL XCHG AL,AH MOV DX,WORD PTR CS:[Cfg_Port+06h] OUT DX,AL RET Write_Configuration_Data ENDP Superio_Set_Reg proc near push ax MOV DX,WORD PTR CS:[Cfg_Port+04h] mov al,cl out dx,al pop ax inc dx out dx,al ret Superio_Set_Reg endp.
Half-size SBC HSB-800P Set_Logic_Device proc near push ax push cx xchg al,cl mov cl,07h call Superio_Set_Reg pop cx pop ax ret Set_Logic_Device endp ;Select 02Eh->Index Port, 02Fh->Data Port Cfg_Port DB 087h,001h,055h,055h DW 02Eh,02Fh END Main Note: Interrupt level mapping 0Fh-Dh: not valid 0Ch: IRQ12 . .
Half-size SBC HSB-800P Appendix B I/O Information Appendix B I/O Information B-1
Half-size SBC B.
Half-size SBC HSB-800P B.2 Memory Address Map B.3 IRQ Mapping Chart B.
Half-Size Board HSB-800P Appendix C Mating Connector Appendix C Mating Connector C - 1
Half-Size Board HSB-800P C.1 List of Mating Connectors and Cables The table notes mating connectors and available cables.
Half-Size Board LAN1 IR1 CN10 CN9 COM1 COM2 COM3 COM4 VGA1 CN7 CN6 CN8 CN5 Ethernet UDE Connector IrDA JIH VEI Connector Electronics Mini-Din PS/2 Connector KB Pin Header COM Port Connector Serial Port Box Header Serial Port Box Header Serial Port Box Header CRT Display Connector LVDS Connector Inverter Connector ATX Power Connector with BP Big 4P Power Connector CONTEK HO-BASE HSB-800P RT1-165AB B1A 21B12050-X XS10B-01G -4/2.
