Industrial Motherboard IMBA-880 Rev.B IMBA-880 Rev.B Intel® Core 2 Duo/ Pentium® 4/ Celeron® D LGA775 Processor Integrated VGA on Intel® 945G With PCI-Express［x16］ Slot 4 x DDRII 533/667 Dual Channel Memory 8 USB 2.0 / 2 COMs IMBA-880 Manual Rev.B 1st Ed.
Industrial Motherboard IMBA-880 Rev.B Copyright Notice This document is copyrighted, 2008. All rights are reserved. The original manufacturer reserves the right to make improvements to the products described in this manual at any time without notice. No part of this manual may be reproduced, copied, translated, or transmitted in any form or by any means without the prior written permission of the original manufacturer. Information provided in this manual is intended to be accurate and reliable.
Industrial Motherboard IMBA-880 Rev.B Acknowledgments All other products’ name or trademarks are properties of their respective owners. Award is a trademark of Award Software International, Inc. Intel®, Core 2 Duo, Pentium® 4, and Celeron® D are trademarks of Intel® Corporation. ® Microsoft Windows is a registered trademark of Microsoft Corp. PC/AT, PS/2, and VGA are trademarks of International Business Machines Corporation.
Industrial Motherboard IMBA-880 Rev.B Packing List Before you begin installing your card, please make sure that the following materials have been shipped: • 1 Floppy Cable • 1 ATA-100 Cable • 1 Serial Cable • 1 USB Cable • 4 Serial ATA Cable • 1 CPU Cooler Fan for LGA 775 Pentium® 4 • 1 IMBA-880 Rev.
Industrial Motherboard IMBA-880 Rev.B Contents Chapter 1 General Information 1.1 Introduction................................................................ 1-2 1.2 Features .................................................................... 1-3 1.3 Specifications ............................................................ 1-4 Chapter 2 Quick Installation Guide 2.1 Safety Precautions .................................................... 2-2 2.2 Location of Connectors and Jumpers .......................
Industrial Motherboard IMBA-880 Rev.B 2.18 FAN Connector (FAN2~5)....................................... 2-10 2.19 4-Pin Power Connector (CN14) .............................. 2-10 Chapter 3 CPU, Heatsink and Fan Installation 3.1 CPU Installation and motherboard handling. ............ 3-2 Chapter 4 Award BIOS Setup 4.1 System Test and Initialization. .................................. 4-2 4.2 Award BIOS Setup .................................................... 4-3 Chapter 5 Driver Installation 5.
Industrial Motherboard IMBA-880 Rev.
Industrial Motherboard IMBA-880 Rev.B 1.1 Introduction The IMBA-880 Rev.B is AAEON’s Industrial Motherboard which adopts Intel® Core to Duo/ Pentium® 4/ Celeron® D LGA775 CPU (Supports 1066/880/533MHz FSB). The high-speed system ® chipset is one of Intel leader accounts. The IMBA-880 Rev.B is designed for Industrial Motherboard with ATX form factor. Integrating with GMA950 2D/3D Graphics Accelerator which makes the IMBA-880 Rev.
Industrial Motherboard IMBA-880 Rev.B 1.2 Features Supports Intel® Core 2 Duo/ Pentium® 4 / Celeron-D LGA775 CPU (1066/800/533MHz FSB) DDRII Memory Support up to 4GB Integrated GMA950 2D/3D Graphics Accelerator with PCI-Express［x16］Slot, VGA Support 8 USB 2.0/ 2 RS-232/422/485/ 1 Parallel/ 1 IrDA port 10/100Base-TX Ethernet Ultra ATA100 & SATAII & CompactFalsh Type II Storage (Optional) Watchdog Function 1~255 Sec.
Industrial Motherboard IMBA-880 Rev.B 1.3 Specifications System CPU Intel® Core 2 Duo Pentium® 4/ Celeron® D LGA 775 CPU (Supports 1066/ 800/ 533MHz FSB) System Memory 4 x 240-pin 1.8V DDR II DIMM Socket, support Dual Channel DDR memory up to 4GB (DDRII 533/667) Note: Due to chipset resource allocation, the system may detect less than 4G system memory when installing four 1G DDR II memory modules.
Industrial Motherboard IMBA-880 Rev.B Expansion Interface PCI, PCI-Express RTC Internal RTC Battery Lithium battery Power Requirement ATX 12V Power Consumption 95W, with Pentium D 3.2GHz/FSB (Typical) 800MHz/ 1MB x 2 L2 Cache EMC CE/ FCC Class A Operating Temp. 0oC~40oC (32oF~104oF) Board Size 12”(L) x9.6” (W) (304.8mm x 243.8mm) Gross Weight 0.71lb (0.
Industrial Motherboard IMBA-880 Rev.B I/O: ICH7/R + Winbond 83627EHF Floppy Drive Interface One Standard FDD port, supports up to two floppy devices IR Interface One IrDA Tx/Rx header Audio (Daughter board) AC-97 pin-header (optional Audio Daughter board) Serial Port Two COM ports: (Internal Pin Header x 1, External D-sub x 1); COM 1,2: RS-232/422/485 Parallel Port Supports SPP/ EPP/ ECP Mode USB Eight USB 2.
Industrial Motherboard IMBA-880 Rev.B Chapter 2 Quick Installation Guide Notice: The Quick Installation Guide is derived from Chapter 2 of the user manual. For other chapters and further installation instructions, please refer to the user manual CD-ROM that came with the product. Part No.
Industrial Motherboard IMBA-880 Rev.B 2.1 Safety Precautions Always completely disconnect the power cord from your board whenever you are working on it. Do not make connections while the power is on, because a sudden rush of power can damage sensitive electronic components. Always ground yourself to remove any static charge before touching the board. Modern electronic devices are very sensitive to static electric charges. Use a grounding wrist strap at all times.
Industrial Motherboard IMBA-880 Rev.B 2.
Industrial Motherboard 2.3 Mechanical Drawing Chapter 2 Quick Installation Guide 2-4 IMBA-880 Rev.
Industrial Motherboard IMBA-880 Rev.B 2.4 List of Jumpers The board has a number of jumpers that allow you to configure your system to suit your application. The table below shows the function of each of the board's jumpers: Label Function JP1 Clear CMOS JP3 CFD Master/ Slave Selection JP5 CFD Power Selection 2.5 List of Connectors The board has a number of connectors that allow you to configure your system to suit your application.
Industrial Motherboard IMBA-880 Rev.
Industrial Motherboard IMBA-880 Rev.B 2.6 Setting Jumpers You configure your card to match the needs of your application by setting jumpers. A jumper is the simplest kind of electric switch. It consists of two metal pins and a small metal clip (often protected by a plastic cover) that slides over the pins to connect them. To “close” a jumper you connect the pins with the clip. To “open” a jumper you remove the clip. Sometimes a jumper will have three pins, labeled 1, 2 and 3.
Industrial Motherboard IMBA-880 Rev.B 2.7 CMOS Selection (JP1) JP1 Function Open Normal (Default) Close Clear CMOS 2.8 CF Master/ Slave Selection (JP3) JP3 Function Open Master (Default) Close Slave 2.9 CF Power Selection (JP5) JP5 Function 1-2 +5V (Default) 2-3 +3.3V 2.10 Front Panel Connector (FP1) Pin Signal Pin Signal 1 Power On Button (+) 2 Reset Switch (+) 3 Power On Button (-) 4 Reset Switch (-) 5 IDE LED (+) 6 Power LED (+) 7 IDE LED (-) 8 Power LED (-) 2.
Industrial Motherboard IMBA-880 Rev.B 2.12 LAN LED Connector (CN1) Pin Signal Pin Signal 1 Link_LED(-) 2 Active_LED(+) 2.13 USB Connector (CN7, CN8) Pin Signal Pin Signal 1 +5V 2 GND 3 USBD1- 4 GND 5 USBD1+ 6 USBD2+ 7 GND 8 USBD2- 9 GND 10 +5V 2.14 AC97 Connector (CN9) Pin Signal Pin Signal 1 AC_RST- 2 AC_SYNC 3 AC_DAIN2 4 AC_DAOUT 5 GND 6 AC_BCLK 7 GND 8 +5V 9 Lock 10 +3.3V 2.
Industrial Motherboard 2.16 IrDA Connector (IR1) Pin Signal 1 +5V 2 N.C 3 IRRX 4 GND 5 IRTX 6 N.C 2.17 Fan Connector (FAN1) Pin Signal 1 GND 2 +12V 3 Speed Sense 4 Speed CTRL 2.18 FAN Connector (FAN2~5) Pin Signal 1 GND 2 +12V 3 Speed Sense 2.19 4-Pin Power Connector (CN14) Pin Signal 1 +5V 2 GND 3 GND 4 +12V Chapter 2 Quick Installation Guide 2-10 IMBA-880 Rev.
Industrial Motherboard IMBA-880 Rev.
Industrial Motherboard IMBA-880 Rev.
Industrial Motherboard IMBA-880 Rev.B 3.1 CPU installation and motherboard handling Note: When integrating a Pentium 4 processor-based system, be sure to take the proper electrostatic discharge (ESD) precautions. Caution: Please follow the steps below to ensure proper installation of your processor. Failure to follow these instructions may result in damage to your CPU and/or your motherboard.
Industrial Motherboard IMBA-880 Rev.B b. Rotate Load Plate to fully open position. c. Remove the Protective Cover Caution: Do not touch the Socket Contacts. This may result in damage to the contacts. Note: Visually inspect the contact area for bent contacts and foreign material.
Industrial Motherboard IMBA-880 Rev.B Step 2: (Processor Handling) Note: Handle Processor by substrate edges only. Caution: Do not touch processor contacts at any time a. Remove processor from shipping media by grasping substrate edges only b. Visually inspect the processor gold pad array for presence of foreign material. If foreign material is present the pads may be wiped clean with a lint-free cloth and isopropyl alcohol. c. Locate the connector 1 indicator and the two orientation notches.
Industrial Motherboard IMBA-880 Rev.B Step 3: (Positioning the CPU into socket) a. Grasp the processor with your thumb and forefinger on the edges with the orientation notches. The socket has cut-outs for your fingers when handled in this orientation. b. Carefully place the CPU into the socket with a purely vertical motion. c. Verify that the CPU is in the socket body and properly mated to the orientation keys. The Alignment Key is for you to check if the CPU is aligned with the CPU notch properly.
Industrial Motherboard IMBA-880 Rev.B d. Close the upper plate (A), place the load lever back to the original position and tightly wedge the lever into the fastening tab. (B) A B Step 4: (Heatsink/ Fan Installation). a. Place bottom bracket underneath the socket making sure that threaded socket is aligned with the holes in the motherboard.
Industrial Motherboard IMBA-880 Rev.B b. Viewing the board again from the topside make sure the bracket on the solder side has not shifted from its position. Daub thermal compound on the CPU. c. Place the Heatsink on the top of CPU. Please make sure that the four screws are aligned with the holes on the board.
Industrial Motherboard IMBA-880 Rev.B d. Fasten the four screws. First fasten the two screws (yellow) and then fasten the two screws (red) in sequence to secure the heatsink in place. e. Connect the CPU fan cable to the power connector labeled FAN1 on the board.
Industrial Motherboard IMBA-880 Rev.
Industrial Motherboard 4.1 IMBA-880 Rev.B System Test and Initialization These routines test and initialize board hardware. If the routines encounter an error during the tests, you will either hear a few short beeps or see an error message on the screen. There are two kinds of errors: fatal and non-fatal. The system can usually continue the boot up sequence with non-fatal errors.
Industrial Motherboard 4.2 IMBA-880 Rev.B Award BIOS Setup Awards BIOS ROM has a built-in Setup program that allows users to modify the basic system configuration. This type of information is stored in battery-backed CMOS RAM so that it retains the Setup information when the power is turned off. Entering Setup Power on the computer and press immediately. This will allow you to enter Setup. Standard CMOS Features Use this menu for basic system configuration. (Date, time, IDE, etc.
Industrial Motherboard IMBA-880 Rev.B Advanced Chipset Features Use this menu to change the values in the chipset registers and optimize your system performance. Integrated Peripherals Use this menu to specify your settings for integrated peripherals. (Primary slave, secondary slave, keyboard, mouse etc.) Power Management Setup Use this menu to specify your settings for power management. (HDD power down, power on by ring, KB wake up, etc.
Industrial Motherboard IMBA-880 Rev.B has designated the custom BIOS to maximize performance, the factory has the right to change these defaults to meet their needs. Set Supervisor/User Password Use this menu to set Supervisor/User Passwords. Save and Exit Setup Save CMOS value changes to CMOS and exit setup. Exit Without Saving Abandon all CMOS value changes and exit setup. You can refer to the "AAEON BIOS Item Description.pdf" file in the CD for the meaning of each setting in this chapter.
Industrial Motherboard IMBA-880 Rev.
Industrial Motherboard IMBA-880 Rev.B The IMBA-880 Rev.B comes with an AutoRun CD-ROM that contains all drivers and utilities that can help you to install the driver automatically. Insert the driver CD, the driver CD-title will auto start and show the installation guide. If not, please follow the sequence below to install the drivers. Follow the sequence below to install the drivers: Step 1 – Install INF Driver Step 2 – Install VGA Driver Step 3 – Install LAN Driver Step 4 – Install Audio Driver USB 2.
Industrial Motherboard 5.1 IMBA-880 Rev.B Installation: Insert the IMBA-880 Rev.B CD-ROM into the CD-ROM drive. And install the drivers from Step 1 to Step 4 in order. Step 1 – Install INF Driver 1. Click on the Step 1-INF folder and select the OS your system is 2. Double click on the .exe file 3. Follow the instructions that the window shows 4. The system will help you install the driver automatically Step 2 – Install VGA Driver 1. Click on the Step 2-VGA folder and select the OS your system is 2.
Industrial Motherboard IMBA-880 Rev.B Step 4 – Install Audio Driver 1. Click on the Step 4-AUDIO folder and double click on the wdm_a371 file 2. Follow the instructions that the window shows 3.
Industrial Motherboard IMBA-880 Rev.
Industrial Motherboard IMBA-880 Rev.B A.1 Programming IMBA-880 Rev.B utilizes W83627EHG chipset as its watchdog timer controller. Below are the procedures to complete its configuration and the AAEON intial watchdog timer program is also attached based on which you can develop customized program to fit your application.
Industrial Motherboard IMBA-880 Rev.B (3) Exit the W83627EHG config Mode. Undesired result may occur if the config Mode is not exited normally. (1) Enter the W83627EHG config Mode To enter the W83627EHG config Mode, two special I/O write operations are to be performed during Wait for Key state. To ensure the initial state of the key-check logic, it is necessary to perform two write operations to the Special Address port (2EH).
Industrial Motherboard IMBA-880 Rev.B = 10 Power LED pin is a 1Hz toggle pulse with 50 duty cycle. = 11 Power LED pin is a 1/4Hz toggle pulse with 50 duty cycle. Bit 5-4 : Reserved Bit 3 : select WDTO count mode. Bit 2 =0 second =1 minute : Enable the rising edge of keyboard Reset (P20) to force Time-out event.
Industrial Motherboard IMBA-880 Rev.B WatchDog Timer Register III (Index=F7h, Default=00h) Bit 7 Bit 6 : Mouse interrupt reset Enable or Disable =1 Watchdog Timer is reset upon a Mouse interrupt =0 Watchdog Timer is not affected by Mouse interrupt : Keyboard interrupt reset Enable or Disable =1 Watchdog Timer is reset upon a Keyboard interrupt =0 Watchdog Timer is not affected by Keyboard interrupt Bit 5 : Force Watchdog Timer Time-out.
Industrial Motherboard IMBA-880 Rev.B A.2 W83627EHG Watchdog Timer Initial Program Example: Setting 10 sec.
Industrial Motherboard IMBA-880 Rev.B ;/////////////////////////////////////////////////////////////////////////////////////////////// Dec dx Mov al,0f5h ;CRF5 (PLED mode register) Out dx,al Inc dx In al,dx And al,not 08h ;Set second as counting unit Out dx,al ;/////////////////////////////////////////////////////////////////////////////////////////////// Dec dx Mov al,0f6h ; CRF6 Out dx,al Inc dx Mov al,10 ;Set timeout interval as 10 sec.
Industrial Motherboard IMBA-880 Rev.
Industrial Motherboard B.1 I/O Address Map Appendix B I/O Information B - 2 IMBA-880 Rev.
Industrial Motherboard IMBA-880 Rev.B B.2 1st MB Memory Address Map B.
Industrial Motherboard B.4 DMA Channel Assignments Appendix B I/O Information B - 4 IMBA-880 Rev.
Industrial Motherboard IMBA-880 Rev.
Industrial Motherboard IMBA-880 Rev.B C.1 List of Mating Connectors and Cables The table notes mating connectors and available cables.
Industrial Motherboard FAN1 FAN2~ FAN5 LAN1 IR1 KM1 COM1 COM2 VGA1 FAN Connector FAN Connector Ethernet Connector IrDA Connector IMBA-880 Rev.B Catch Electronics Catch Electronics BOTHHAN D JIH VEI Electronics 1190-700-04 2 1190-700-03 S LU1T516-43 LF 21B12050-X XS10B-01G -4/2.
