Industrial Motherboard IMBI-Q45 IMBI-Q45 Intel® CoreTM 2 Duo/Quad LGA775 Processor Dual-channel LVDS Two 240-pin DDR3 800/1066 SDRAM 3 SATA 3.0Gb/s / Multiple PCIe PCI interface with Golden Finger 6 USB 2.0/ 2 RS-232/ 2 RJ-45 IMBI-Q45 Manual Rev.A 3rd Ed.
Industrial Motherboard IMBI-Q45 Copyright Notice This document is copyrighted, 2011. All rights are reserved. The original manufacturer reserves the right to make improvements to the products described in this manual at any time without notice. No part of this manual may be reproduced, copied, translated, or transmitted in any form or by any means without the prior written permission of the original manufacturer. Information provided in this manual is intended to be accurate and reliable.
Industrial Motherboard IMBI-Q45 Acknowledgments All other products’ name or trademarks are properties of their respective owners. z Award is a trademark of Award Software International, Inc. z CompactFlash™ is a trademark of the Compact Flash Association. z Intel®, Core™2 Duo are trademarks of Intel® Corporation. z Microsoft Windows is a registered trademark of Microsoft Corp. z ITE is a trademark of Integrated Technology Express, Inc.
Industrial Motherboard IMBI-Q45 Packing List Before you begin installing your card, please make sure that the following materials have been shipped: • 1 IMBI-Q45 Mini-ITX Main Board • 2 SATA Signal Cable • 1 COM Port Cable with DB-9 • 1 USB Cable • 1 I/O Shield • 1 CD-ROM for Manual (in PDF Format) and Drivers If any of these items should be missing or damaged, please contact your distributor or sales representative immediately.
Industrial Motherboard IMBI-Q45 Contents Chapter 1 General Information 1.1 Introduction................................................................ 1-2 1.2 Features .................................................................... 1-3 1.3 Specifications ............................................................ 1-4 Chapter 2 Quick Installation Guide 2.1 Safety Precautions .................................................... 2-2 2.2 Location of Connectors and Jumpers .......................
Industrial Motherboard IMBI-Q45 Chapter 4 Driver Installation 4.1 Installation ................................................................. 4-3 Appendix A Programming The Watchdog Timer A.1 Programming .........................................................A-2 A.2 ITE8718 Watchdog Timer Initial Program..............A-5 Appendix B I/O Information B.1 I/O Address Map ....................................................B-2 B.2 Memory Address Map............................................B-3 B.
Industrial Motherboard IMBI-Q45 Chapter 1 General Information Chapter 1 General Information 1- 1
Industrial Motherboard IMBI-Q45 1.1 Introduction The IMBI-Q45 supports Intel® CoreTM 2 Duo/Quad LGA775 processors. Moreover it supports DDR3 800/1066 memory up to 4GB. This model accommodates two Intel® Gigabit Ethernet controllers that those are controlled by Intel® Q45 and ICH10DO. This configuration provides outstanding computing ability, fast network connections and multi-task data transmission.
Industrial Motherboard IMBI-Q45 1.2 Features z Intel® CoreTM 2 Duo/Quad LGA775 Processor z Dual-Channel DDR3 800/1066 Memory (Up to 4GB), 2GB Double Side DIMM x 2 z Intel® Gigabit Ethernet x 2 z SATA 3.0Gb/s x 3, RAID 0,1,5,10 z USB 2.
Industrial Motherboard IMBI-Q45 1.3 Specifications System z Form Factor Mini-ITX z Processor Intel Core ® TM 2 Duo/Quad LGA775 CPU, FSB 800/1066/ 1333 MHz (Q9000, E8000, E7000, E5000, E6000, E4000, E2000, Conroe L series), TDP 95W Max.
Industrial Motherboard IMBI-Q45 Digital I/O interface (4 input/4 output) z Watchdog Timer 1~255 steps, can be set with software on Super I/O z H/W Status Monitor Monitoring system temperature, voltage, and cooling fan status z Expansion Interface Multiple PCIe and PCI interface with Golden Finger z Power Requirement Standard ATX with 24-pin connector x 1 z Board Size (L x W) 6.7" x 6.7" (170 x 170 mm) z Gross Weight 0.66 lb (0.
Industrial Motherboard IMBI-Q45 I/O z Serial Port RS-232 x 2 (one with header, one with port) z KB & Mouse Keyboard x 1 & Mouse x 1 z Universal Serial Bus USB 2.
Industrial Motherboard IMBI-Q45 Chapter 2 Quick Installation Guide Notice: The Quick Installation Guide is derived from Chapter 2 of user manual. For other chapters and further installation instructions, please refer to the user manual CD-ROM that came with the product. Part No.
Industrial Motherboard IMBI-Q45 2.1 Safety Precautions Always completely disconnect the power cord from your board whenever you are working on it. Do not make connections while the power is on, because a sudden rush of power can damage sensitive electronic components. Always ground yourself to remove any static charge before touching the board. Modern electronic devices are very sensitive to static electric charges. Use a grounding wrist strap at all times.
Industrial Motherboard IMBI-Q45 2.
Industrial Motherboard 2.
Industrial Motherboard IMBI-Q45 2.4 List of Jumpers The board has a number of jumpers that allow you to configure your system to suit your application.
Industrial Motherboard IMBI-Q45 2.5 List of Connectors The board has a number of connectors that allow you to configure your system to suit your application.
Industrial Motherboard CN8 IMBI-Q45 Expansion Power Connector Chapter 2 Quick Installation Guide 2 - 7
Industrial Motherboard IMBI-Q45 2.6 Setting Jumpers You configure your card to match the needs of your application by setting jumpers. A jumper is the simplest kind of electric switch. It consists of two metal pins and a small metal clip (often protected by a plastic cover) that slides over the pins to connect them. To “close” a jumper you connect the pins with the clip. To “open” a jumper you remove the clip. Sometimes a jumper will have three pins, labeled 1, 2 and 3.
Industrial Motherboard IMBI-Q45 2.7 Clear CMOS (JP1) Normal Open Clear CMOS 1-2 Normal 2-3 (Default) 2.8 ME_TP1 Enable iAMT set up Open (Default) Disable iAMT 1-2 set up 2.9 Front Panel Connector (FP1) Pin Signal Pin Signal 1 Power On Button (+) 2 Reset Switch (+) 3 Power On Button (-) 4 Reset Switch (-) 5 IDE LED (+) 6 Power LED (+) 7 IDE LED (-) 8 Power LED (-) 2.
Industrial Motherboard IMBI-Q45 2.11 USB Connector (USB1) Pin Signal Pin Signal 1 +5V 2 GND 3 USBD1- 4 GND 5 USBD1+ 6 USBD2+ 7 GND 8 USBD2- 9 GND 10 +5V 2.12 CD-IN (J1) Pin Signal 1 CD-R 2 CD-GND 3 CD-GND 4 CD-L 2.13 RS232 Serial Port Connector (COM2) Pin Signal Pin Signal 1 DCD 2 RXD 3 TXD 4 DTR 5 GND 6 DSR 7 RTS 8 CTS 9 RI 10 N.C 2.
Industrial Motherboard IMBI-Q45 7 OUT2(Bit 1) 8 OUT3(Bit 0) 9 +5V 10 GND 2.15 Power Connector (CN8) Pin Signal 1 GND 2 3.3V 3 3.3V 4 3.
Industrial Motherboard IMBI-Q45 Below Table for China RoHS Requirements 产品中有毒有害物质或元素名称及含量 AAEON Main Board/ Daughter Board/ Backplane 有毒有害物质或元素 部件名称 铅 汞 镉 六价铬 多溴联苯 多溴二苯醚 (Pb) (Hg) (Cd) (Cr(VI)) (PBB) (PBDE) × ○ ○ ○ ○ ○ × ○ ○ ○ ○ ○ 印刷电路板 及其电子组件 外部信号 连接器及线材 O：表示该有毒有害物质在该部件所有均质材料中的含量均在 SJ/T 11363-2006 标准规定的限量要求以下。 X：表示该有毒有害物质至少在该部件的某一均质材料中的含量超出 SJ/T 11363-2006 标准规定的限量要求。 备注：此产品所标示之环保使用期限，系指在一般正常使用状况下。 Chapter 2 Quick Installation Guide 2 - 12
Industrial Motherboard IMBI-Q45 Chapter 3 Award BIOS Setup Chapter 3 Award BIOS Setup 3-1
Industrial Motherboard 3.1 IMBI-Q45 System Test and Initialization These routines test and initialize board hardware. If the routines encounter an error during the tests, you will either hear a few short beeps or see an error message on the screen. There are two kinds of errors: fatal and non-fatal. The system can usually continue the boot up sequence with non-fatal errors.
Industrial Motherboard 3.2 IMBI-Q45 Award BIOS Setup Awards BIOS ROM has a built-in Setup program that allows users to modify the basic system configuration. This type of information is stored in battery-backed CMOS RAM so that it retains the Setup information when the power is turned off. Entering Setup Power on the computer and press immediately. This will allow you to enter Setup. Standard CMOS Features Use this menu for basic system configuration. (Date, time, IDE, etc.
Industrial Motherboard IMBI-Q45 PC Health Status This menu allows you to set the shutdown temperature for your system. Load Fail-Safe Defaults Use this menu to load the BIOS default values for the minimal/stable performance for your system to operate. Load Optimized Defaults Use this menu to load the BIOS default values that are factory settings for optimal performance system operations.
Industrial Motherboard IMBI-Q45 Chapter 4 Driver Installation Chapter 4 Driver Installation 4-1
Industrial Motherboard IMBI-Q45 The IMBI-Q45 comes with a CD-ROM that contains all drivers your need. Follow the sequence below to install the drivers: Step 1 – Install INF Driver Step 2 – Install VGA Driver Step 3 – Install LAN Driver Step 4 – Install AUDIO Driver Step 5 – Install RAID Driver Please read following instructions for detailed installations.
Industrial Motherboard IMBI-Q45 4.1 Installation: Insert the IMBI-Q45 CD-ROM into the CD-ROM Drive. And install the drivers from Step 1 to Step 5 in order. Step 1 – Install INF Driver 1. Click on the Step 1-INF folder and then double click on the Setup.exe 2. Follow the instructions that the window shows 3. The system will help you to install the driver automatically Step 2 – Install VGA Driver 1. Click on the Step 2-VGA folder and select the OS your system is 2. Double click on .
Industrial Motherboard IMBI-Q45 2. Double click on .exe file located in each OS folder 3. Follow the instructions that the window shows 4. The system will help you to install the driver automatically Step 5 – Install RAID Driver 1. Click on the Step 5-RAID folder and select the OS your system is 2. Double click on .exe file located in each OS folder 3. Follow the instructions that the window shows 4.
Industrial Motherboard IMBI-Q45 Note: For Windows Vista you can use Floppy, CD/DVD or USB. ----------------------------------------------------------------------------------------Important Please follow the instruction below to make an “Intel® RAID Driver” for yourself. 1. Insert the AAEON CD into the CD-ROM drive 2. Click the “Browse CD” on the Setup screen 3. Copy all the contents in \\Step5 - RAID\F6 Install Floppy\32bit or 64bit to a formatted floppy diskette 4.
Industrial Motherboard 8. IMBI-Q45 The next screen should confirm that you have selected the Intel® RAID controller. Press ENTER again to continue. 9. You have successfully installed the Intel® Matrix Storage Manager driver, and Windows setup should continue. 10. Leave the disk in the floppy drive until the system reboots itself. Windows setup will need to copy the files from the floppy again after the RAID volume is formatted, and Windows setup starts copying files.
Industrial Motherboard IMBI-Q45 Appendix A Programming the Watchdog Timer Appendix A Programming the Watchdog Timer A-1
Industrial Motherboard IMBI-Q45 A.1 Programming IMBI-Q45 utilizes ITE 8718 chipset as its watchdog timer controller. ( K version ) Below are the procedures to complete its configuration and the AAEON intial watchdog timer program is also attached based on which you can develop customized program to fit your application. Configuring Sequence Description After the hardware reset or power-on reset, the ITE 8718 enters the normal mode with all logical devices disabled except KBC.
Industrial Motherboard IMBI-Q45 (1) Enter the MB PnP Mode To enter the MB PnP Mode, four special I/O write operations are to be performed during Wait for Key state. To ensure the initial state of the key-check logic, it is necessary to perform four write opera-tions to the Special Address port (2EH). Two different enter keys are provided to select configuration ports (2Eh/2Fh) of the next step.
Industrial Motherboard Bit 7-2 1 0 IMBI-Q45 Description Reserved Returns to the Wait for Key state. This bit is used when the configuration sequence is completed. Resets all logical devices and restores configuration registers to their power-on states. WatchDog Timer Control Register (Index=71h, Default=00h) Bit 7 6 5 4 3-2 1 0 Description WDT is reset upon a CIR interrupt WDT is reset upon a KBC (Mouse) interrupt WDT is reset upon a KBC (Keyboard) interrupt Reserved Reserved Force Time-out.
Industrial Motherboard IMBI-Q45 Default=00h) Bit Description 7-0 WDT Time-out value 7-0 WatchDog Timer Time-out Value (MSB) Register (Index=74h, Default=00h) Bit Description 7-0 WDT Time-out value 15-8 A.2 ITE8718 Watchdog Timer Initial Program .MODEL SMALL .
Industrial Motherboard IMBI-Q45 call Superio_Set_Reg ;Clear by keyboard or mouse interrupt mov al, 0f0h mov cl, 71h call Superio_Set_Reg ;unit is second.
Industrial Motherboard IMBI-Q45 OUT DX,AL INC SI LOOP Init_1 RET Enter_Configuration_Mode ENDP Exit_Configuration_Mode PROC NEAR MOV AX,0202h CALL Write_Configuration_Data RET Exit_Configuration_Mode ENDP Check_Chip PROC NEAR MOV AL,20h CALL Read_Configuration_Data CMP AL,87h JNE Not_Initial MOV AL,21h CALL Read_Configuration_Data CMP AL,12h JNE Not_Initial Need_Initial: Appendix A Programming the Watchdog Timer A-7
Industrial Motherboard IMBI-Q45 STC RET Not_Initial: CLC RET Check_Chip ENDP Read_Configuration_Data PROC NEAR MOV DX,WORD PTR CS:[Cfg_Port+04h] OUT DX,AL MOV DX,WORD PTR CS:[Cfg_Port+06h] IN AL,DX RET Read_Configuration_Data ENDP Write_Configuration_Data PROC NEAR MOV DX,WORD PTR CS:[Cfg_Port+04h] OUT DX,AL XCHG AL,AH MOV DX,WORD PTR CS:[Cfg_Port+06h] OUT DX,AL RET Write_Configuration_Data ENDP Superio_Set_Reg proc near push ax Appendix A Programming the Watchdog Timer A-8
Industrial Motherboard IMBI-Q45 MOV DX,WORD PTR CS:[Cfg_Port+04h] mov al,cl out dx,al pop ax inc dx out dx,al ret Superio_Set_Reg endp.
Industrial Motherboard Note: Interrupt level mapping 0Fh-Dh: not valid 0Ch: IRQ12 . .
Industrial Motherboard IMBI-Q45 Appendix B I/O Information Appendix B I/O Information B-1
Industrial Motherboard B.
Industrial Motherboard IMBI-Q45 B.
Industrial Motherboard B.3 IRQ Mapping Chart B.
Industrial Motherboard IMBI-Q45 Appendix C Mating Connector Appendix C Mating Connector C - 1
Industrial Motherboard IMBI-Q45 C.1 List of Mating Connectors and Cables The table notes mating connectors and available cables. Connector Label Function Mating Connector Vendor SATA0 SATA1 SATA2 FP1 FP2 SATA Connector SATA Connector SATA Connector Front Panel Connector Front Panel Connector ATX1 USB_LAN2 LAN1+2*USB FOXCONN Connector AUDIO1 USB1 AUDIO Connector USB PIN HEADER.
Industrial Motherboard COM1 COM2 VGA1 CN1 CN2 CN8 D-SUB Connector Serial Port Box Header CRT Display Connector CRT+DVI CONNECTOR Digital I/O Pin Header Catch Electronics Catch Electronics Catch Electronics TechBast POWER CONNECT JIH VEI Electronics CPU_FAN1 FAN Connector SYS_FAN1 FAN Connector SYS_FAN2 FAN Connector J1 IrDA Connector JIH VEI Electronics Catch Electronics Catch Electronics Catch Electronics JIH VEI Electronics IMBI-Q45 3117-00009P 1147-000- Serial Port 10S Cable 3125-00015SB D205D
