Industrial Motherboard IMBI-QM57 IMBI-QM57 Intel® CoreTM i5/i7 Mobile Processor Dual View VGA, DVI, HDMI, LVDS Two 204-pin DDR3 800/1066 SODIMM 3 SATA2/ 1 PCI-Express[x4]/ 1 PCI 1 Mini PCI-Express 8 USB 2.0/ 3 RS-232/ 1 RS-232/422/485 IMBI-QM57 Manual Rev.A 3rd Ed.
Industrial Motherboard IMBI-QM57 Copyright Notice This document is copyrighted, 2012. All rights are reserved. The original manufacturer reserves the right to make improvements to the products described in this manual at any time without notice. No part of this manual may be reproduced, copied, translated, or transmitted in any form or by any means without the prior written permission of the original manufacturer. Information provided in this manual is intended to be accurate and reliable.
Industrial Motherboard IMBI-QM57 Acknowledgments All other products’ name or trademarks are properties of their respective owners. Award is a trademark of Award Software International, Inc. CompactFlash™ is a trademark of the Compact Flash Association. Intel®, Core™ i5/i7 are trademarks of Intel® Corporation. Microsoft Windows is a registered trademark of Microsoft Corp. ITE is a trademark of Integrated Technology Express, Inc.
Industrial Motherboard IMBI-QM57 Packing List Before you begin installing your card, please make sure that the following materials have been shipped: 1 IMBI-QM57 Mini-ITX Main Board 1 SATA Signal Cable 1 COM Port Cable with DB-9 1 USB Cable 1 I/O Shield 1 CD-ROM for Manual (in PDF Format) and Drivers If any of these items should be missing or damaged, please contact your distributor or sales representative immediately.
Industrial Motherboard IMBI-QM57 Contents Chapter 1 General Information 1.1 Introduction................................................................ 1-2 1.2 Features .................................................................... 1-3 1.3 Specifications ............................................................ 1-4 Chapter 2 Quick Installation Guide 2.1 Safety Precautions .................................................... 2-2 2.2 Location of Connectors and Jumpers .......................
Industrial Motherboard IMBI-QM57 2.19 COM1~2 Port LED Connector (CN8).................... 2-13 2.20 COM3~4 Port LED Connector (CN9).................... 2-13 2.21 LAN Port LED Connector (CN10) ......................... 2-14 2.22 RS-232/422/485 Pin Header (COM2) ................... 2-14 2.23 RS-232 Pin Header (COM3~4) ............................. 2-14 2.24 Pin Header (USB3, USB4) .................................... 2-14 2.25 FAN Connector (FAN1, FAN2).............................. 2-15 2.
Industrial Motherboard IMBI-QM57 B.3 IRQ Mapping Chart ................................................B-5 B.4 DMA Channel Assignments .................................B-5 Appendix C Mating Connector C.1 List of Mating Connectors and Cables.................. C-2 Appendix D RAID & AHCI Settings D.1 Setting RAID ......................................................... D-2 D.2 Setting AHCI .......................................................
Industrial Motherboard IMBI-QM57 Chapter 1 General Information Chapter 1 General Information 1- 1
Industrial Motherboard IMBI-QM57 1.1 Introduction The IMBI-QM57 supports Intel® CoreTM i5/i7 Mobile processor. Moreover it supports DDR3 800/1066 memory up to 8GB. This model accommodates two Intel® PCI-Express Gigabit Ethernet controllers that those are controlled by Intel® 82577LM and Intel® 82574L/82583V. This configuration provides outstanding computing ability, fast network connections and multi-task data transmission. The graphic controller is integrated on Intel® Gen 6.
Industrial Motherboard IMBI-QM57 1.2 Features Intel® 32/45nm Core™ i7/i5 rPGA988 CPU Integrated Graphics & Memory Controller Intel® QM57 Dual-Channel DDR3 800/1066 Memory up to 8 GB Intel® Gigabit Ethernet x 2 Support Intel® AMT 6.0 Intel® Gen 6.0 Integrated Graphics Engine Supports Dual View With VGA, DVI, HDMI, LVDS HD Audio SATA2 x 3, RAID 0, 1, 5, 10 USB 2.
Industrial Motherboard IMBI-QM57 1.3 Specifications System Form Factor Mini-ITX Processor Intel® 32/45nm Core™ i5/i7 rPGA988 CPU, TDP: 35W Max. System Memory Supports Dual Channel with 2 x 204-pin DDR3 800/1066 SODIMM, up to 8GB Chipset Intel® QM57 Ethernet Intel® PCI-Express 10/100/ 1000Base-TX, RJ-45 x 2 LAN1: Intel® 82577LM (supports Intel® AMT 6.
Industrial Motherboard IMBI-QM57 or 1 min./step H/W Status Monitor Monitoring system temperature, voltage, and cooling fan status Expansion Interface PCI-Express[x4] x 1, PCI x 1, Mini PCI-Express x 1 Power Requirement Standard ATX 24-pin connector Board Size (L x W) 6.7" x 6.7" (170 x 170 mm) Gross Weight 0.88 lb (0.
Industrial Motherboard IMBI-QM57 header x 3 support 5V/12V on the 9th pin Keyboard & Mouse Keyboard x 1 & Mouse x 1 Universal Serial Bus USB 2.
Industrial Motherboard IMBI-QM57 Chapter 2 Quick Installation Guide Chapter 2 Quick Installation Guide 2 - 1
Industrial Motherboard IMBI-QM57 2.1 Safety Precautions Always completely disconnect the power cord from your board whenever you are working on it. Do not make connections while the power is on, because a sudden rush of power can damage sensitive electronic components. Always ground yourself to remove any static charge before touching the board. Modern electronic devices are very sensitive to static electric charges. Use a grounding wrist strap at all times.
Industrial Motherboard IMBI-QM57 2.
Industrial Motherboard Solder Side Chapter 2 Quick Installation Guide 2 - 4 IMBI-QM57
Industrial Motherboard IMBI-QM57 2.
Industrial Motherboard Solder Side Chapter 2 Quick Installation Guide 2 - 6 IMBI-QM57
Industrial Motherboard IMBI-QM57 2.4 List of Jumpers The board has a number of jumpers that allow you to configure your system to suit your application. The table below shows the function of each of the board's jumpers: Label Function CMOS1 CMOS Setting Selection JP1 Auto PWRBTN Selection JP2 CFD Voltage 3.3V/5V Selection JP3 TPM Setting Selection JP4 LCD Power and Inverter Power Selection JP5 COM1 +12V/+5V/RING Selection JP6 COM2 +12V/+5V/RING Selection 2.
Industrial Motherboard IMBI-QM57 COM3~4 RS-232 Pin header KM1 PS2 Keyboard/Mouse Connector USB_LAN1 100/1000Base-TX Ethernet & Dual USB Connector USB_LAN2 100/1000Base-TX Ethernet & Dual USB Connector AUDIO1 Audio Lin-in/Lin-out/MIC DIMM1,DIMM2 DDR3 DIMM Slot USB3,USB4 USB Pin header FAN1, FAN2 4-pin System Fan Connector ATX1 4-pin ATX Power +12V Connector ATX2 24-pin ATX Power SATA1~SATA3 SATA Connector DIO1 Digital I/O PIC1 PCI Slot PCIE1 PCIE Slot CN11 Mini-PCIE Slot PWR1
Industrial Motherboard IMBI-QM57 2.6 Setting Jumpers You configure your card to match the needs of your application by setting jumpers. A jumper is the simplest kind of electric switch. It consists of two metal pins and a small metal clip (often protected by a plastic cover) that slides over the pins to connect them. To “close” a jumper you connect the pins with the clip. To “open” a jumper you remove the clip. Sometimes a jumper will have three pins, labeled 1, 2 and 3.
Industrial Motherboard IMBI-QM57 2.7 CMOS Setting (CMOS1) JP1 Function 1-2 Normal (Default) 2-3 Clear CMOS 2.8 Auto PWRBTN Selection (JP1) JP1 Function 1-2 Don’t use Auto PWRBTN (Default) 2-3 Use Auto PWRBTN 2.9 CFD Voltage 3.3V/5V Selection (JP2) JP2 Function 1-2 +3.3V 2-3 +5V (Default) 2.10 TPM Setting (JP3) JP3 Function 1-2 Save ME RTC Register (Default) 2-3 Clear ME RTC Register 2.
Industrial Motherboard IMBI-QM57 2.12 COM1 +12V/+5V/RING Selection (JP5) JP5 Function 1-2 +12V 3-4 Ring (Default) 5-6 +5V 2.13 COM2 +12V/+5V/RING Selection (JP6) JP6 Function 1-2 +12V 3-4 Ring (Default) 5-6 +5V 2.14 Front Panel Connector (CN2) Pin Signal Pin Signal 1 Power On Button (-) 2 Power On Button (+) 3 HDD LED(-) 4 HDD LED(+) 5 External Speaker (-) 6 External Speaker (+) 7 Power LED (-) 8 Power LED (+) 9 Reset Switch (-) 10 Reset Switch (+) 2.
Industrial Motherboard IMBI-QM57 2.16 LVDS Inverter (CN4) Pin Signal 1 12V / 5V 2 VCON 3 GND 4 GND 5 INV_EN 2.17 LVDS Connector (CN5) Pin Signal Pin Signal 1 BKL_EN 2 N.C.
Industrial Motherboard IMBI-QM57 2.18 CD-IN Pin Header (CN6) Pin Signal 1 CD-R 2 CD-GND 3 CD-GND 4 CD-L 2.19 COM1~2 Port LED Connector (CN8) Pin Signal Pin Signal 1 COM1_RS232_PWR 2 GND 3 TX_LED_COM1 4 GND 5 RX_LED_COM1 6 GND 7 COM2_RS232_PWR 8 GND 9 TX_LED_COM2 10 GND 11 RX_LED_COM2 12 GND 13 COM2_RS485_PWR 14 COM2_RS422_PWR 2.
Industrial Motherboard IMBI-QM57 2.21 LAN Port LED Connector (CN10) Pin Signal Pin Signal 1 LAN1_LED_D2 2 LAN1_LED_LNK#_ACT 3 LAN1_LED_1000# 4 LAN1_LED_100# 5 LAN2_LED_D2 6 ACT_2_LED 7 SPD1K_2_LED 8 SPD100_2_LED 2.22 RS-232/422/485 Pin Header (COM2) Pin Signal Pin Signal 1 DCD 2 RXD 3 TXD 4 DTR 5 GND 6 DSR 7 RTS 8 CTS 9 RI 2.23 RS-232 Pin Header (COM3~4) Pin Signal Pin Signal 1 DCD 2 RXD 3 TXD 4 DTR 5 GND 6 DSR 7 RTS 8 CTS 9 RI 2.
Industrial Motherboard 9 GND IMBI-QM57 10 +5V 2.25 FAN Connector (FAN1, FAN2) Pin Signal Pin Signal 1 GND 2 +12V 3 FAN_TAC 4 FAN_CTL 2.26 4-pin ATX Power Connector (ATX1) Pin Signal Pin Signal 1 GND 2 GND 3 +12V 4 +12V 2.27 24-pin ATX Power Connector (ATX2) Pin Signal Pin Signal 1 +3.3V 2 +3.3V 3 GND 4 +5V 5 GND 6 +5V 7 GND 8 PWROK 9 +5VSB 10 +12V 11 +12V 12 +3.3V 13 +3.
Industrial Motherboard IMBI-QM57 3 TXN 4 GND 5 RXN 6 RXP 7 GND 2.
Industrial Motherboard IMBI-QM57 Below Table for China RoHS Requirements 产品中有毒有害物质或元素名称及含量 AAEON Main Board/ Daughter Board/ Backplane 有毒有害物质或元素 部件名称 铅 汞 镉 六价铬 多溴联苯 多溴二苯醚 (Pb) (Hg) (Cd) (Cr(VI)) (PBB) (PBDE) × ○ ○ ○ ○ ○ × ○ ○ ○ ○ ○ 印刷电路板 及其电子组件 外部信号 连接器及线材 O：表示该有毒有害物质在该部件所有均质材料中的含量均在 SJ/T 11363-2006 标准规定的限量要求以下。 X：表示该有毒有害物质至少在该部件的某一均质材料中的含量超出 SJ/T 11363-2006 标准规定的限量要求。 备注：此产品所标示之环保使用期限，系指在一般正常使用状况下。 Chapter 2 Quick Installation Guide 2 - 17
Industrial Motherboard IMBI-QM57 Chapter 3 AMI BIOS Setup Chapter 3 AMI BIOS Setup 3-1
Industrial Motherboard 3.1 IMBI-QM57 System Test and Initialization These routines test and initialize board hardware. If the routines encounter an error during the tests, you will either hear a few short beeps or see an error message on the screen. There are two kinds of errors: fatal and non-fatal. The system can usually continue the boot up sequence with non-fatal errors.
Industrial Motherboard 3.2 IMBI-QM57 AMI BIOS Setup AMI BIOS ROM has a built-in Setup program that allows users to modify the basic system configuration. This type of information is stored in battery-backed CMOS RAM so that it retains the Setup information when the power is turned off. Entering Setup Power on the computer and press or immediately. This will allow you to enter Setup. Main Set the date, use tab to switch between date elements.
Industrial Motherboard IMBI-QM57 Chapter 4 Driver Installation Chapter 4 Driver Installation 4-1
Industrial Motherboard IMBI-QM57 The IMBI-QM57 comes with a CD-ROM that contains all drivers your need. Follow the sequence below to install the drivers: Step 1 – Install INF Driver Step 2 – Install VGA Driver Step 3 – Install LAN Driver Step 4 – Install AUDIO Driver Step 5 – Install ME Driver Step 6 – Install RAID Driver Please read following instructions for detailed installations.
Industrial Motherboard IMBI-QM57 4.1 Installation: Insert the IMBI-QM57 CD-ROM into the CD-ROM Drive. And install the drivers from Step 1 to Step 6 in order. Step 1 – Install INF Driver 1. Click on the Step1 - INF folder and then double click on the Setup.exe 2. Follow the instructions that the window shows 3. The system will help you to install the driver automatically Step 2 – Install VGA Driver 1. Click on the Step2 - VGA folder and select the OS your system is 2. Double click on Setup.
Industrial Motherboard IMBI-QM57 3. Follow the instructions that the window shows 4. The system will help you to install the driver automatically Step 5 – Install ME Driver 1. Click on the Step5 - ME folder and double click on Setup.exe file 2. Follow the instructions that the window shows 3.
Industrial Motherboard IMBI-QM57 Appendix A Programming the Watchdog Timer Appendix A Programming the Watchdog Timer A-1
Industrial Motherboard IMBI-QM57 A.1 Programming IMBI-QM57 utilizes ITE 8781 chipset as its watchdog timer controller. Below are the procedures to complete its configuration and the AAEON initial watchdog timer program is also attached based on which you can develop customized program to fit your application. Configuring Sequence Description After the hardware reset or power-on reset, the ITE 8781 enters the normal mode with all logical devices disabled except KBC.
Industrial Motherboard IMBI-QM57 There are three steps to complete the configuration setup: (1) Enter the MB PnP Mode; (2) Modify the data of configuration registers; (3) Exit the MB PnP Mode. Undesired result may occur if the MB PnP Mode is not exited normally. (1) Enter the MB PnP Mode To enter the MB PnP Mode, four special I/O write operations are to be performed during Wait for Key state.
Industrial Motherboard IMBI-QM57 WatchDog Timer Configuration Registers Configure Control (Index=02h) This register is write only. Its values are not sticky; that is to say, a hardware reset will automatically clear the bits, and does not require the software to clear them.
Industrial Motherboard IMBI-QM57 Watch Dog Timer 1, 2, 3 Configuration Register (Index=72h, 82h, 92h Default=001s0000b) Watch Dog Timer 1,2,3 Time-Out Value (LSB) Register (Index=73h,83h,93h, Default=38h) Watch Dog Timer 1,2,3 Time-Out Value (MSB) Register (Index=74h,84h,94h Default=00h) Appendix A Programming the Watchdog Timer A-5
Industrial Motherboard IMBI-QM57 A.2 ITE8781 Watchdog Timer Initial Program .MODEL SMALL .CODE Main: CALL Enter_Configuration_mode CALL Check_Chip mov cl, 7 call Set_Logic_Device ;time setting mov cl, 10 ; 10 Sec dec al Watch_Dog_Setting: ;Timer setting mov al, cl mov cl, 73h call Superio_Set_Reg ;Clear by keyboard or mouse interrupt mov al, 0f0h mov cl, 71h call Superio_Set_Reg ;unit is second.
Industrial Motherboard IMBI-QM57 call Superio_Set_Reg ; game port enable mov cl, 9 call Set_Logic_Device Initial_OK: CALL Exit_Configuration_mode MOV AH,4Ch INT 21h Enter_Configuration_Mode PROC NEAR MOV SI,WORD PTR CS:[Offset Cfg_Port] MOV DX,02Eh MOV CX,04h Init_1: MOV AL,BYTE PTR CS:[SI] OUT DX,AL INC SI LOOP Init_1 RET Enter_Configuration_Mode ENDP Exit_Configuration_Mode PROC NEAR MOV AX,0202h Appendix A Programming the Watchdog Timer A-7
Industrial Motherboard CALL Write_Configuration_Data RET Exit_Configuration_Mode ENDP Check_Chip PROC NEAR MOV AL,20h CALL Read_Configuration_Data CMP AL,87h JNE Not_Initial MOV AL,21h CALL Read_Configuration_Data CMP AL,81h JNE Not_Initial Need_Initial: STC RET Not_Initial: CLC RET Check_Chip ENDP Read_Configuration_Data PROC NEAR MOV DX,WORD PTR CS:[Cfg_Port+04h] Appendix A Programming the Watchdog Timer A-8 IMBI-QM57
Industrial Motherboard IMBI-QM57 OUT DX,AL MOV DX,WORD PTR CS:[Cfg_Port+06h] IN AL,DX RET Read_Configuration_Data ENDP Write_Configuration_Data PROC NEAR MOV DX,WORD PTR CS:[Cfg_Port+04h] OUT DX,AL XCHG AL,AH MOV DX,WORD PTR CS:[Cfg_Port+06h] OUT DX,AL RET Write_Configuration_Data ENDP Superio_Set_Reg proc near push ax MOV DX,WORD PTR CS:[Cfg_Port+04h] mov al,cl out dx,al pop ax inc dx out dx,al ret Superio_Set_Reg endp.
Industrial Motherboard Set_Logic_Device proc IMBI-QM57 near push ax push cx xchg al,cl mov cl,07h call Superio_Set_Reg pop cx pop ax ret Set_Logic_Device endp ;Select 02Eh->Index Port, 02Fh->Data Port Cfg_Port DB 087h,001h,055h,055h DW 02Eh,02Fh END Main Note: Interrupt level mapping 0Fh-Dh: not valid 0Ch: IRQ12 . .
Industrial Motherboard IMBI-QM57 Appendix B I/O Information Appendix B I/O Information B-1
Industrial Motherboard B.
Industrial Motherboard IMBI-QM57 Appendix B I/O Information B-3
Industrial Motherboard B.
Industrial Motherboard IMBI-QM57 B.3 IRQ Mapping Chart B.
Industrial Motherboard IMBI-QM57 Appendix C Mating Connector Appendix C Mating Connector C - 1
Industrial Motherboard IMBI-QM57 C.1 List of Mating Connectors and Cables The table notes mating connectors and available cables.
Industrial Motherboard KM1 PWR1 CN1 CN2 CN4 CN5 CN6 CN7 IMBI-QM57 Mini-Din PS/2 KB/MS Pin Header WAFER.4P Connector COM1+DVI Connector Front Panel Connector Foxconn MH11061- N/A P36-4F N/A HO-BASE P201-04 N/A N/A TechBast Electronics Astron Electronics N/A N/A N/A N/A LVDS Inverter Connector LVDS Connector CD-I 2.
Industrial Motherboard IMBI-QM57 Appendix D RAID & AHCI Settings Appendix D RAID & AHCI Settings D-1
Industrial Motherboard IMBI-QM57 D.
Industrial Motherboard IMBI-QM57 Step 3: The setting procedures “ In BIOS Setup Menu” A: Advanced -> SATA Configuration -> SATA Mode -> RAID Mode Step 4: The setting procedures “In BIOS Setup Menu” B: Advanced -> Launch Storage OpROM -> Enabled Appendix D RAID & AHCI Settings D-3
Industrial Motherboard IMBI-QM57 Step 5: The setting procedures “In BIOS Setup Menu” C: Boot -> Boot Option #1 -> DVD-ROM Type Step 6: The setting procedures “In BIOS Setup Menu” D: Save & Exit -> Save Changes and Exit Appendix D RAID & AHCI Settings D-4
Industrial Motherboard IMBI-QM57 Step 7: Press Ctrl-I to enter MAIN MENU Step 8: Choose “1.
Industrial Motherboard Step 9: RAID Level -> RAID0(Stripe) Step 10: Choose “Create Volume” Appendix D RAID & AHCI Settings D-6 IMBI-QM57
Industrial Motherboard IMBI-QM57 Step 11: Choose “Y” Step 12: Choose “5.
Industrial Motherboard Step 13: Choose “Y” Step 14: Setup OS Appendix D RAID & AHCI Settings D-8 IMBI-QM57
Industrial Motherboard IMBI-QM57 Step 15: Press “F6” Step 16: Choose “S” Appendix D RAID & AHCI Settings D-9
Industrial Motherboard IMBI-QM57 Step 17: Choose “Intel(R) ICH8M-E/ICH9M-E/5 Series SATA RAID Controller” Step 18: It will show the model number you select and then press “ENTER” Appendix D RAID & AHCI Settings D-10
Industrial Motherboard IMBI-QM57 Step 19: Setup is starting Windows Appendix D RAID & AHCI Settings D-11
Industrial Motherboard IMBI-QM57 D.
Industrial Motherboard IMBI-QM57 Step 3: The setting procedures “ In BIOS Setup Menu” A: Advanced -> SATA Configuration -> SATA Configuration -> SATA Mode -> AHCI Mode Step 4: The setting procedures “In BIOS Setup Menu” B: Boot -> Boot Option #1 -> DVD-ROM Type Appendix D RAID & AHCI Settings D-13
Industrial Motherboard IMBI-QM57 Step 5: The setting procedures “In BIOS Setup Menu” C: Save & Exit -> Save Changes and Exit Step 6: Setup OS Appendix D RAID & AHCI Settings D-14
Industrial Motherboard IMBI-QM57 Step 7: Press “F6” Step 8: Choose “S” Appendix D RAID & AHCI Settings D-15
Industrial Motherboard IMBI-QM57 Step 9: Choose “Intel(R) 5 Series 6 Port SATA AHCI Controller” Step 10: It will show the model number you select and then press “ENTER” Appendix D RAID & AHCI Settings D-16
Industrial Motherboard IMBI-QM57 Step 11: Setup is loading files Appendix D RAID & AHCI Settings D-17
