User Manual

ManualsBrandsAAEON ManualsHardwarePCM-3660 Rev.B

PC/104 Peripheral Module PCM-3660 Rev.B

PCM-3660 Rev.B Quick Installation Guide

1-1

Notice

This guide is designe d for experienced use rs to setu p the syste m in

the shortest time.

Safety Precautions

Always completely disconnect the po wer cord

from your board whenever you are working

on it. Do not make connections while the

power is on, because a sudden rush of power

can damage sensitive elec tronic

components.

Always ground yourself to remove any static

charge before touching the board. Modern

electronic devices are very sensitive to static

electric charges. Use a grounding wrist strap

at all times. Place all electronic com ponents

on a static-dissipative surface o r in a

static-shielded bag when they are not in the

chassis.

Summary of content (14 pages)

PAGE 1
PC/104 Peripheral Module PCM-3660 Rev.B Notice This guide is designed for experienced users to setup the system in the shortest time. Safety Precautions Always completely disconnect the power cord from your board whenever you are working on it. Do not make connections while the power is on, because a sudden rush of power can damage sensitive electronic components. Always ground yourself to remove any static charge before touching the board.
PAGE 2
PC/104 Peripheral Module PCM-3660 Rev.B Introduction The PCM-3660 Rev.B is a high-performance 16-bit jumperless Ethernet interface module that attaches to the PC/104 connector on your CPU card or PC/104 CPU module. The module automatically senses whether it is connected to an 8-bit or 16-bit PC/104 system. The PCM-3660 Rev.B fully complies with IEEE 802.3 10 Mbps CSMA/CD standards and is 100% Novell NE2000 compatible. The module includes a built-in 10BASE-T transceiver and RJ-45 connector.
PAGE 3
PC/104 Peripheral Module PCM-3660 Rev.B Features  Conforms to IEEE 802.
PAGE 4
PC/104 Peripheral Module PCM-3660 Rev.B Specification Hardware  Form Factor PC/104  I/O address 200, 220, 240, 260, 280, 2A0, 2C0, 300, 320, 340, 380 or 3A0  Interrupt levels IRQ3, 4, 5, 9, 10, 11, or 15  Boot ROM address C0000, C8000, D0C00 or D8000H  Data bus 8-bit or 16-bit, auto-sensing  Connectors 16-bit PC/104 stack through connector RJ-45 connector for 10BASE-T, 16-pin insulation displacement connector for AUI  Dimension 3.5” x 3.
PAGE 5
PC/104 Peripheral Module PCM-3660 Rev.B -Netware serverdriver Standard  PC/104 8-bit and 16-bit compatible  Built in IEEE 802.3 10 Mbps CSMA/CD 10BASE-T transceiver  10BASE-2, 10BASE-5 and 10BASE-FOIRL by external transceiver General  Power +5 V 400 mA max.  Operating 32°F~140°F (0°C ~ 60°C) Temperature  Storage 5°F~176°F (-15°C ~ 80°C) Temperature  Humidity 10% ~ 90% PCM-3660 Rev.
PAGE 6
PC/104 Peripheral Module PCM-3660 Rev.B Installation Your package should contain the following items. If they are missing, damaged or fail to meet specifications, contact your dealer/sales representative immediately.  PCM-3660 Rev.B  Drivers PCM-3660 Rev.
PAGE 7
PC/104 Peripheral Module PCM-3660 Rev.B Software Configuration The PCM-3660 Rev. B module is supplied with a software utility disk. This disk contains the files necessary for setting up the Ethernet controller. Directories and files on the disk are as follows: 1. RSET8019.EXE This program enables you to view the current Ethernet configuration, reconfigure the Ethernet interface (medium type, etc.), and execute useful diagnostic functions. 2. PG8019.
PAGE 8
PC/104 Peripheral Module PCM-3660 Rev.B Ethernet Interface Configuration The PCM-3660 Rev.B onboard Ethernet interface supports all major network operating systems. I/O address and interrupts are easily configured via the RSET801 9.EXE program included on the utility disk. The RSET8019.EXE program provides two ways to configure the Ethernet interface. Configuration can be done automatically when you choose PNP (plug and play).
PAGE 9
PC/104 Peripheral Module PCM-3660 Rev.B 2. At the prompt type RSET8019.exe and press . Then the Ethernet configuration program will be displayed. 3. A simple screen displays the available options for the Ethernet interface. Highlight the option you are going to change and using the Up and Down keys. To change a selected item press , and a window will show the available options. Highlight your selection and press .
PAGE 10
PC/104 Peripheral Module PCM-3660 Rev.B A boot ROM allows you to boot the workstation directly from the server, avoiding the need for local hard or floppy disks. Install the boot ROM as shown below. Make sure that you align the notch on the ROM chip with the notch on the socket. PCM-3660 Rev.
PAGE 11
PC/104 Peripheral Module PCM-3660 Rev.B Hardware Installation The following instructions show how to install the PCM-3660 Rev.B module on a CPU card. The process is similar to PC/104 CPU modules’ and see the figures. Make sure that you have properly configured the module’s jumpers and attached a boot ROM if necessary. Warning! TURN OFF your PC power supply whenever you install or remove the PCM-3660 Rev.B or connect and disconnect cables. 1. Turn off the power of the PC.
PAGE 12
PC/104 Peripheral Module PCM-3660 Rev.B way into the connector; Do not push too hard or the module may be damaged. If the CPU card has only an 8-bit bus, make sure that the pins on connector PC104CD1 do not touch anything. 7. Secure the module to the CPU card to the threaded hole in the CPU card using the included screw. 8. Reinstall the CPU card and system unit cover. Reconnect the cables you removed in step 2. Turn on the power. This completes the hardware installation.
PAGE 13
PC/104 Peripheral Module PCM-3660 Rev.B Ethernet Connection Specifications The following table shows the network specifications for each Ethernet. Ethernet Data Type transfer Topology Cable Type Segment Length rate 10 Base-2 10 Base-5 10 Base-T 10 Mbps 10 Mbps 10 Mbps Bus Bus Star 50 Ohm Ethernet 185m (607 ft.) thin (RG-58) max. 50 Ohm Ethernet 500m (1640 ft.) thin (RG-11) max. 100 Ohm 100m (328 ft.) unshielded twisty max. pair Pin Assignment (CN2) PCM-3660 Rev.
PAGE 14
PC/104 Peripheral Module PCM-3660 Rev.B RJ-45 Connector (RJ1) Pin Signal Description 1 TD+ Data transmission positive 2 TD- Data transmission negative 3 RD+ Data reception positive 6 RD- Data reception negative LCD Indicators The module’s two LED indicators show the status of the communication link and traffic. LED On Flashing Off LED2 - Traffic No traffic LED3 Link OK - Link failure RJ-45 Pin assignments PCM-3660 Rev.