Compact Board PCM-5895 Rev.B PCM-5895 Rev.B Onboard AMD Geode LX 800/900 Processor Up to 24-bit LVDS LCD 184-pin DDR 333/400 Memory Up to 1GB 4 USB 2.0 / 8-bit Digital I/O / 4 COM PCM-5895 Manual Rev.B 1st Ed. Aug.
Compact Board PCM-5895 Rev.B Copyright Notice This document is copyrighted, 2008. All rights are reserved. The original manufacturer reserves the right to make improvements to the products described in this manual at any time without notice. No part of this manual may be reproduced, copied, translated, or transmitted in any form or by any means without the prior written permission of the original manufacturer. Information provided in this manual is intended to be accurate and reliable.
Compact Board PCM-5895 Rev.B Acknowledgments All other products’ name or trademarks are properties of their respective owners. Award is a trademark of Award Software International, Inc. CompactFlash™ is a trademark of the Compact Flash Association. AMD, the AMD Arrow logo and combinations thereof are trademarks of Advanced Micro Devices, Inc. ® Microsoft Windows is a registered trademark of Microsoft Corp. ITE is a trademark of Integrated Technology Express, Inc.
Compact Board PCM-5895 Rev.B Packing List Before you begin installing your card, please make sure that the following materials have been shipped: • 1 PCM-5895 Rev.B CPU Card • 1 Quick Installation Guide • 1 CD-ROM for manual (in PDF format) and drivers • 1 9657666600 Jumper Cap If any of these items should be missing or damaged, please contact your distributor or sales representative immediately.
Compact Board PCM-5895 Rev.B Contents Chapter 1 General Information 1.1 Introduction................................................................ 1-2 1.2 Features .................................................................... 1-3 1.3 Specifications ............................................................ 1-4 Chapter 2 Quick Installation Guide 2.1 Safety Precautions .................................................... 2-2 2.2 Location of Connectors and Jumpers ....................... 2-3 2.
Compact Board PCM-5895 Rev.B 2.17 Front Panel (CN7) ................................................... 2-13 2.18 USB Port #3 & Port #4 (CN8).................................. 2-14 2.19 PC/104 ISA Interface (CN9).................................... 2-14 2.20 ATX Power Socket (CN10) ..................................... 2-17 2.21 AT Power Socket (CN11)........................................ 2-18 2.22 IDE Hard Drive (CN12)............................................ 2-18 2.23 CRT Display (CN 14)...........
Compact Board Chapter 3 PCM-5895 Rev.B Award BIOS Setup 3.1 System Test and Initialization. .................................. 3-2 3.2 Award BIOS Setup .................................................... 3-3 Chapter 4 Driver Installation 4.1 Software Drivers........................................................ 4-2 4.2 Necessary to Know ................................................... 4-3 4.3 Installing VGA Driver ................................................. 4-4 4.4 Installing AES Driver ...
Compact Board PCM-5895 Rev.
Compact Board PCM-5895 Rev.B 1.1 Introduction PCM-5895 Rev.B adopts an onboard AMD Geode LX 800/900 processor. The AMD LX series processors are ideal for applications that require low power consumption and stable performance. The system memory features 184-pin DDR DIMM up to 1GB. Moreover, the PCM-5895 Rev.B supports PCI, PCI-104 and PC/104 for flexible expansion. Customers are always eager to find a low-priced, multi-functional product. The PCM-5895 Rev.B is definitely your best choice.
Compact Board PCM-5895 Rev.B 1.2 Features Onboard AMD Geode LX 800/900 Processor One DIMM DDR 333/400 up to 1GB Up to 24-bit LVDS TFT Panel, TTL/LVDS LCD, CRT Dual 10/100Base-TX Ethernet Supports PC/104+ Expansion Slot AC97 2CH Audio USB2.
Compact Board PCM-5895 Rev.B 1.3 Specifications System CPU Onboard AMD Geode LX800 (900 optional) Processors System Memory 184-pin DDR DIMM x 1, Max.
Compact Board Board Size PCM-5895 Rev.B 8”(L) x 5.72” (W) (203mm x 146mm) Gross Weight 1.2 lb (0.
Compact Board PCM-5895 Rev.
Compact Board PCM-5895 Rev.B Chapter 2 Quick Installation Guide Notice: The Quick Installation Guide is derived from Chapter 2 of user manual. For other chapters and further installation instructions, please refer to the user manual CD-ROM that came with the product. Part No. 2007589520 Printed in Taiwan Aug.
Compact Board PCM-5895 Rev.B 2.1 Safety Precautions Always completely disconnect the power cord from your board whenever you are working on it. Do not make connections while the power is on, because a sudden rush of power can damage sensitive electronic components. Always ground yourself to remove any static charge before touching the board. Modern electronic devices are very sensitive to static electric charges. Use a grounding wrist strap at all times.
Compact Board PCM-5895 Rev.B 2.
Compact Board Solder Side Chapter 2 Quick Installation Guide 2- 4 PCM-5895 Rev.
Compact Board PCM-5895 Rev.B 2.
Compact Board Solder Side Chapter 2 Quick Installation Guide 2- 6 PCM-5895 Rev.
Compact Board PCM-5895 Rev.B 2.4 List of Jumpers The board has a number of jumpers that allow you to configure your system to suit your application.
Compact Board PCM-5895 Rev.B 2.5 List of Connectors The board has a number of connectors that allow you to configure your system to suit your application.
Compact Board PCM-5895 Rev.
Compact Board PCM-5895 Rev.B 2.6 Setting Jumpers You configure your card to match the needs of your application by setting jumpers. A jumper is the simplest kind of electric switch. It consists of two metal pins and a small metal clip (often protected by a plastic cover) that slides over the pins to connect them. To “close” a jumper you connect the pins with the clip. To “open” a jumper you remove the clip. Sometimes a jumper will have three pins, labeled 1, 2 and 3.
Compact Board PCM-5895 Rev.B 2.7 AT/ATX Power Type Selection (JP2) JP2 Function 2-3 ATX Power Supply (Default) 1-2 AT Power Supply 2.8 CFD Master/Slave Selection (JP6) JP6 Function 1-2 Slave (Default) 2-3 Master 2.9 Clear CMOS (JP7) JP7 Function 1-2 Normal (Default) 2-3 Clear CMOS 2.
Compact Board 3-4 +5V 5-6 RI (Default) PCM-5895 Rev.B COM3, COM4 JP11 1-3 2-4 3-5 4-6 Function +12V +5V (Default) 2.11 LCD Power & Clock Selection (JP12) JP12 Function 1-3 Normal (Default) 3-5 Inverse 2-4 +5Vlcd 4-6 +3Vlcd (Default) 2.12 Inverter Voltage Selection (JP13) JP13 Function 1-2 +12V 2-3 +5V (Default) 2.13 Contrast IC Power Selection (JP17) JP17 Function 1-2 +5V (Default) 2-3 +3.
Compact Board PCM-5895 Rev.B 2.14 Fan Control Circuit Power Selection (JP18) JP18 Function 1-2 +12V (Default) 2-3 +5V 2.15 FAN Connector (CN1) Pin Signal 1 GND 2 +12V 3 FAN Sense 2.16 USB Port #1 and Port #2 (CN6) Pin Signal Pin Signal 1 VDD0 2 GND 3 D0- 4 GND 5 D0+ 6 D1+ 7 GND 8 D1- 9 GND 10 VDD1 2.
Compact Board PCM-5895 Rev.B 7-8 Power LED 9-10 System Reset Button 2.18 USB Port #3 & Port #4 (CN8) Pin Signal Pin Signal 1 VDD3 2 GND 3 D3- 4 GND 5 D3+ 6 D4+ 7 GND 8 D4- 9 GND 10 VDD4 2.
Compact Board PCM-5895 Rev.
Compact Board PCM-5895 Rev.B J2/P2 Pin D C 1 GND GND 2 MEMCS16* SBHE* 3 IOCS16* LA23 4 IRQ10 LA22 5 IRQ11 LA21 6 IRQ12 LA20 7 IRQ15 LA19 8 IRQ14 LA18 9 DACK0* LA17 10 DRQ0 MEMR* 11 DACK5* MEMW* 12 DRQ5 SD8 13 DACK6* SD9 14 DRQ6 SD10 15 DACK7* SD11 16 DRQ7 SD12 17 +5V SD13 18 MASTER* SD14 19 GND SD15 20 GND GND/KEY PCM-5895 Rev.B does not support PC/104 way legacy ISA-DMA mode cause by AMD architecture.
Compact Board PCM-5895 Rev.B I/O Resource Allocation Method of PC/104 card is for the PCM-5895 Rev.B. PC/104 connector at the PCM-5895 Rev.B cannot automatically get related I/O resource when a new PC/104 card is added because of AMD Geode’s architecture limitation. The following steps are for setting up the I/O resources manually for your reference. 1. Retrieve the resource of the PC/104 card. The information is typically contained in the manual of the PC/104 card.
Compact Board PCM-5895 Rev.B 9 5VSB 19 +5V 10 +12V 20 +5V 2.21 AT Power Socket (CN11) Pin Signal 1 NC 2 +5V 3 +12V 4 -12V 5 GND 6 GND 7 GND 8 GND 9 -5V 10 +5V 11 +5V 12 +5V 2.
Compact Board PCM-5895 Rev.B 9 D4 10 D11 11 D3 12 D12 13 D2 14 D13 15 D1 16 D14 17 D0 18 D15 19 GND 20 N/C 21 DREQ 22 GND 23 IOW# 24 GND 25 IOR# 26 GND 27 IORDY 28 GND 29 DACK# 30 GND 31 IRQ14 32 NC 33 DA1 34 PDIAG# 35 DA0 36 DA2 37 CS#1 38 CS#3 39 Active LED# 40 GND 2.
Compact Board PCM-5895 Rev.B 11 GND 12 VSYNC 13 GND 14 DDCSCL 15 GND 16 GND 2.24 Audio Input/ Output/ CD-in/ MIC (CN15) Pin Signal Pin Signal 1 MIC 2 MIC_VCC 3 Audio Ground 4 CD_GND 5 LINE_IN L 6 CD_L 7 LINE_IN R 8 CD_GND 9 Audio Ground 10 CD_R 11 LINE_OUT L 12 LINE_OUT R 13 Audio Ground 14 Audio Ground 2.
Compact Board PCM-5895 Rev.B 17 PTD7 18 GND 19 ACK# 20 GND 21 BUSY 22 GND 23 PE 24 GND 25 SLCT 26 NC 2.26 Keyboard/Mouse Connector (CN17) Pin Signal Pin Signal 1 Keyboard Data 2 Keyboard Clock 3 GND 4 +5V 5 Mouse Data 6 Mouse Clock 2.
Compact Board PCM-5895 Rev.B Port 4 CN18. pin 4 Bit 4 U40. pin 23 (GPIO24) Port 5 CN18. pin 5 Bit 3 U40. pin 24 (GPIO23) Port 6 CN18. pin 6 Bit 2 U40. pin 25 (GPIO22) Port 7 CN18. pin 7 Bit 1 U40. pin 26 (GPIO21) Port 8 CN18. pin 8 Bit 0 U40. pin 27 (GPIO20) 2.28 Serial Port (CN19) Note: COM 1 & COM 2 support full modem control signals and COM 3 & COM 4 support TX & RX only.
Compact Board PCM-5895 Rev.B 29 GND 30 NC 31 NC 32 NC 33 RXD4 34 NC 35 TXD4 36 NC 37 NC 38 +5V/+12V 39 GND 40 NC COM/ RS-422 mode Pin Signal Pin Signal 11 TXD- 12 NC 13 RXD+ 14 NC 15 TXD+ 16 NC 17 RXD- 18 NC 19 GND 20 NC COM/ RS-485 mode Pin Signal Pin Signal 11 TXD- 12 NC 13 NC 14 NC 15 TXD+ 16 NC 17 NC 18 NC 19 GND 20 NC 2.
Compact Board PCM-5895 Rev.B 3 RXD+ 4 NC (N GND) 5 NC (N GND) 6 RXD- 7 NC (C GND) 8 NC (C GND) 9 GND 10 GND 2.30 LAN LED (CN13, CN25) Pin Signal Pin Signal 1 RX 2 +3.3V 3 LINK10/100 4 +3.3V 5 TX 6 +3.3V 2.31 TFT LCD (CN23) For 24-bit TFT LCD Pin Signal Pin Signal 1 +5VLCD 2 +5VLCD 3 GND 4 GND 5 +3.3VLCD 6 +3.
Compact Board PCM-5895 Rev.B 23 G6 24 G7 25 R0 26 R1 27 R2 28 R3 29 R4 30 R5 31 R6 32 R7 33 GND 34 GND 35 LCD_CLK 36 LCD_VS 37 LCD_DE 38 LCD_HS 39 NC 40 TP For 18-bit TFT LCD Pin Signal Pin Signal 1 +5VLCD 2 +5VLCD 3 GND 4 GND 5 +3.3VLCD 6 +3.
Compact Board PCM-5895 Rev.B 27 R0 28 R1 29 R2 30 R3 31 R4 32 R5 33 GND 34 GND 35 LCD_CLK 36 LCD_VS 37 LCD_DE 38 LCD_HS 39 NC 40 TP 2.
Compact Board 29 NC PCM-5895 Rev.B 30 NC 2.33 Ethernet 10/100Base-TX Connector (CN26) Pin Signal Pin Signal 1 RXD- 2 RXD+ 3 NC (N GND) 4 NC (N GND) 5 GND 6 GND 7 NC (C GND) 8 NC (C GND) 9 TXD+ 10 TXD- 2.34 LCD Inverter (CN27) Pin Signal Pin Signal 1 12V/5V 4 GND 2 VCON 5 BKL_EN 3 GND 2.
Compact Board PCM-5895 Rev.B 2.36 CAN Bus Connector (CN30, CN31) Pin Signal Pin Signal 1 NC 2 CAN_L 3 ISO_GND 4 NC 5 NC 6 NC 7 CAN_H 8 NC 9 NC 10 NC 2.37 CompactFlash Disk Slot (CFD1) Pin Signal Pin Signal 1 GND 26 GND 2 D3 27 D11 3 D4 28 D12 4 D5 29 D13 5 D6 30 D14 6 D7 31 D15 7 CS#0 32 CS#1 8 GND 33 GND 9 GND 34 IOR# 10 GND 35 IOW# 11 GND 36 +5V/+3.3V 12 GND 37 IRQ14 13 +5V/+3.3V 38 +5V/+3.
Compact Board PCM-5895 Rev.B 14 GND 39 CSEL# 15 GND 40 NC 16 GND 41 RESET# 17 GND 42 IORDY 18 DA2 43 DREQ 19 DA1 44 DACK# 20 DA0 45 DASP# 21 D0 46 PDIAG# 22 D1 47 D8 23 D2 48 D9 24 IO16# 49 D10 25 GND 50 GND Note: There is a limitation when supports Compact Flash and a hard disk drive on the same IDE channel. Below information is from AMD. Frequently Asked Question - FAQ.
Compact Board PCM-5895 Rev.B The problem is related to the fact that one device is on the cable and the other is populated on the motherboard. A 40-pin cable has PDIAG- available on all its connectors. Therefore, PDIAG- may be signaled from the cable-based HDD, through the motherboard, and to the CF (or vice versa). Unfortunately, the higher UDMA modes cannot be supported on a 40-pin cable. An 80-pin cable is typically marked with the specific connectors intended for motherboard and drives.
Compact Board PCM-5895 Rev.
Compact Board PCM-5895 Rev.
Compact Board 3.1 PCM-5895 Rev.B System Test and Initialization These routines test and initialize board hardware. If the routines encounter an error during the tests, you will either hear a few short beeps or see an error message on the screen. There are two kinds of errors: fatal and non-fatal. The system can usually continue the boot up sequence with non-fatal errors.
Compact Board 3.2 PCM-5895 Rev.B Award BIOS Setup Awards BIOS ROM has a built-in Setup program that allows users to modify the basic system configuration. This type of information is stored in battery-backed CMOS RAM so that it retains the Setup information when the power is turned off. Entering Setup Power on the computer and press immediately. This will allow you to enter Setup. Standard CMOS Features Use this menu for basic system configuration. (Date, time, IDE, etc.
Compact Board PCM-5895 Rev.B PC Health Status This menu allows you to set the shutdown temperature for your system. Load Fail-Safe Defaults Use this menu to load the BIOS default values for the minimal/stable performance for your system to operate. Load Optimized Defaults Use this menu to load the BIOS default values that are factory settings for optimal performance system operations.
Compact Board PCM-5895 Rev.
Compact Board PCM-5895 Rev.B 4.1 Software Drivers This chapter describes the operation and installation of the display drivers supplied on the Supporting CD-ROM that are shipped with your product. The onboard VGA adapter is based on the AMD LX VGA Flat Panel/CRT controller. This controller offers a large set of extended functions and higher resolutions. The purpose of the enclosed software drivers is to take advantage of the extended features of the AMD LX VGA Flat Panel/CRT controller.
Compact Board PCM-5895 Rev.B 4.2 Necessary to Know The instructions in this manual assume that you understand elementary concepts of MS-DOS and the IBM Personal Computer.
Compact Board PCM-5895 Rev.B 4.3 Installing VGA Driver Win XP / Win XPe VGA Place the Driver CD-ROM into your CD-ROM drive and follow the steps below to install. 1. Click on Start button 2. Click on Settings button 3. Click on Control Panel button 4. Click on System button 5. Select Hardware and click on Device Manager… 6. Double click on Video Controller (VGA Compatible) 7. Click on Update Driver… 8. Click on Next 9. Select Search for a suitable driver…, then click on Next 10.
Compact Board PCM-5895 Rev.B 4.4 Installing AES Driver Win XP / Win XPe AES Place the Driver CD-ROM into your CD-ROM drive and follow the steps below to install. 1. Click on Start button 2. Click on Settings button 3. Click on Control Panel button 4. Click on System button 5. Select Hardware and click on Device Manager… 6. Double click on Entertainment Encryption/Decryption Controller 7. Click on Update Driver… 8. Click on Next 9. Select Search for a suitable driver…, then click on Next 10.
Compact Board PCM-5895 Rev.B 4.5 Installing PCI to ISA Bridge Driver Win XP / Win XPe System Place the Driver CD-ROM into your CD-ROM drive and follow the following steps to install. 1. Click on Start button 2. Click on Settings button 3. Click on Control Panel button 4. Click on System button 5. Select Hardware and click on Device Manager… 6. Double click on Other PCI Bridge Device 7. Click on Update Driver… 8. Click on Next 9. Select Search for a suitable driver…, then click on Next. 10.
Compact Board PCM-5895 Rev.B 4.6 Installing LAN Driver 1. Click on the Step 4 –lan folder and double click on the Setup.exe 2. Follow the instructions that the window shows 3. The system will help you install the driver automatically 4.7 Ethernet Software Configuration The onboard Ethernet interface supports all major network operating systems. I/O addresses and interrupts are easily configured via the Insyde BIOS Setup.
Compact Board PCM-5895 Rev.B information. 4. After you have made your selections and the configuration is what you want, press . A prompt will appear asking if you want to save the configuration. Press "Y" if you want to save. There are three very useful diagnostic functions offered in the Ethernet Setup Menu as follows: 1. Run EEPROM test 2. Run Diagnostics on Board 3.
Compact Board PCM-5895 Rev.B 8. Click on Next 9. Select Search for a suitable driver…, then click on Next 10. Select Specify a location, then click on Next 11. Click on Browse 12. Select “LXWDMAU” file from CD-ROM (Driver/Step 5 – Audio) then click on Open 13. Click on OK 14. Click on Next 15. Click on Yes 16. Click on Finish 4.9 Installing CAN Bus Driver 1. Click on the Step 6 –CAN bus folder and select the XP folder 2. Double click on the canbus.exe 3. Follow the instructions that the window shows 4.
Compact Board PCM-5895 Rev.
Compact Board PCM-5895 Rev.B A.1 Programming PCM-5895 Rev.B utilizes ITE 8712 chipset as its watchdog timer controller. ( K version ) Below are the procedures to complete its configuration and the AAEON intial watchdog timer program is also attached based on which you can develop customized program to fit your application. Configuring Sequence Description After the hardware reset or power-on reset, the ITE 8712 enters the normal mode with all logical devices disabled except KBC.
Compact Board PCM-5895 Rev.B (1) Enter the MB PnP Mode To enter the MB PnP Mode, four special I/O write operations are to be performed during Wait for Key state. To ensure the initial state of the key-check logic, it is necessary to perform four write opera-tions to the Special Address port (2EH). Two different enter keys are provided to select configuration ports (2Eh/2Fh) of the next step.
Compact Board 1 0 PCM-5895 Rev.B Returns to the Wait for Key state. This bit is used when the configuration sequence is completed. Resets all logical devices and restores configuration registers to their power-on states.
Compact Board PCM-5895 Rev.B A.2 ITE8712 Watchdog Timer Initial Program .MODEL SMALL .CODE Main: CALL Enter_Configuration_mode CALL Check_Chip mov cl, 7 call Set_Logic_Device ;time setting mov cl, 10 ; 10 Sec dec al Watch_Dog_Setting: ;Timer setting mov al, cl mov cl, 73h call Superio_Set_Reg ;Clear by keyboard or mouse interrupt mov al, 0f0h mov cl, 71h call Superio_Set_Reg ;unit is second.
Compact Board PCM-5895 Rev.
Compact Board PCM-5895 Rev.
Compact Board PCM-5895 Rev.B MOV DX,WORD PTR CS:[Cfg_Port+06h] IN AL,DX RET Read_Configuration_Data ENDP Write_Configuration_Data PROC NEAR MOV DX,WORD PTR CS:[Cfg_Port+04h] OUT DX,AL XCHG AL,AH MOV DX,WORD PTR CS:[Cfg_Port+06h] OUT DX,AL RET Write_Configuration_Data ENDP Superio_Set_Reg proc near push ax MOV DX,WORD PTR CS:[Cfg_Port+04h] mov al,cl out dx,al pop ax inc dx out dx,al ret Superio_Set_Reg endp.
Compact Board PCM-5895 Rev.B Set_Logic_Device proc near push ax push cx xchg al,cl mov cl,07h call Superio_Set_Reg pop cx pop ax ret Set_Logic_Device endp ;Select 02Eh->Index Port, 02Fh->Data Port Cfg_Port DB 087h,001h,055h,055h DW 02Eh,02Fh END Main Note: Interrupt level mapping 0Fh-Dh: not valid 0Ch: IRQ12 . .
Compact Board PCM-5895 Rev.
Compact Board PCM-5895 Rev.B B.
Compact Board PCM-5895 Rev.B B.3 IRQ Mapping Chart IRQ0 System Timer IRQ1 Keyboard IRQ2 IRQ3 IRQ4 IRQ5 IRQ6 IRQ7 Cascade to IRQ Controller COM2 COM1 Unused Floppy Printer IRQ8 System CMOS / Real time clock IRQ9 Microsoft ACPI – Compliant system IRQ10 COM3 IRQ11 COM4 IRQ12 PS/2 mouse IRQ13 FPU IRQ14 Primary IDE IRQ15 Reserved B.
Compact Board PCM-5895 Rev.
Compact Board PCM-5895 Rev.B C.1 List of Mating Connectors and Cables The table notes mating connectors and available cables.
Compact Board CN16 Parallel Port CN17 KB/MS HoConnector Base CN18 Digital I/O Catch CN19 Serial Port Astron CN23 TFT LCD E-Call Connector LVDS E-Call Connector LAN2 LED Catch CN24 CN25 CN27 CN29 CN30 CN31 Astron PCM-5895 Rev.B Parallel 1701260200 【2.0mm】 26-4101-213-1G-R Port Cable Keyboard 1700060152 【2.0mm】 & 2005-2WS-6 Mouse Cable 【2.0mm】 1147-000-10-SS Serial 1701401800 【2.0mm】 26-4101-220-1G-R Port Cable 【1.25mm】 0110-01-553-400 【1.25mm】 0110-01-553-300 【2.0mm】 1140-010-06S 【2.