Compact Board PCM-LN02 PCM-LN02 Intel® AtomTM N455/D525 Processors Onboard DDR3 667/800 18-bit or 24-bit LVDS 6 USB 2.0 / 6 COMs / 2 Mini Card/ Digital IO PC/104+ (ISA+PCI)/ CompactFlash/ PCMCIA PCM-LN02 Manual Rev.A 2nd Ed.
Compact Board PCM-LN02 Copyright Notice This document is copyrighted, 2011. All rights are reserved. The original manufacturer reserves the right to make improvements to the products described in this manual at any time without notice. No part of this manual may be reproduced, copied, translated, or transmitted in any form or by any means without the prior written permission of the original manufacturer. Information provided in this manual is intended to be accurate and reliable.
Compact Board PCM-LN02 Acknowledgments All other products’ name or trademarks are properties of their respective owners. AMI is a trademark of American Megatrends Inc. CompactFlash™ is a trademark of the Compact Flash Association. Intel®, and AtomTM are trademarks of Intel® Corporation. Microsoft Windows is a registered trademark of Microsoft Corp. ITE is a trademark of Integrated Technology Express, Inc.
Compact Board PCM-LN02 Packing List Before you begin installing your card, please make sure that the following materials have been shipped: 9657666600 Jumper Cap PCM-LN02 5.25” CPU Board CD-ROM for manual (in PDF format) and drivers If any of these items should be missing or damaged, please contact your distributor or sales representative immediately.
Compact Board PCM-LN02 Contents Chapter 1 General Information 1.1 Introduction................................................................ 1-2 1.2 Features .................................................................... 1-3 1.3 Specifications ............................................................ 1-4 Chapter 2 Quick Installation Guide 2.1 Safety Precautions .................................................... 2-2 2.2 Location of Connectors and Jumpers ....................... 2-3 2.
Compact Board PCM-LN02 2.19 Voltage Input Connector (CN7)............................... 2-14 2.20 ATX Power Connector (CN8).................................. 2-14 2.21 +5V/ +12V Output Connector for SATA HDD (CN9)2-15 2.22 IDE Connector (CN10) ............................................ 2-15 2.23 USB Port 1,2 Connector (CN11) ............................. 2-16 2.24 CPU Fan Connector (CN12) ................................... 2-16 2.25 USB Port 3,4 Connector (CN13) ............................. 2-17 2.
Compact Board PCM-LN02 2.44 Digital I/O Connector (CN33) .................................. 2-26 2.45 Front Panel (CN34) ................................................. 2-27 2.46 PCMCIA Slot (CN35)............................................... 2-27 2.47 Compact Flash Disk (CFD1) ................................... 2-27 2.48 Mini-Card Slot #1 (PCIE1)....................................... 2-29 2.49 Mini-Card Slot #2 (PCIE2)....................................... 2-30 Chapter 3 AMI BIOS Setup 3.
Compact Board PCM-LN02 Appendix D Ordering Information D.1 Ordering Information.............................................
Compact Board PCM-LN02 Chapter 1 General Information Chapter 1 General Information 1- 1
Compact Board PCM-LN02 1.1 Introduction The PCM-LN02 supports Intel® AtomTM N455/D525 processors offering a wide range of performance, price and power. The standard onboard DDR3 667/800 memory support up to 2 GB. Dual Ethernet connectivity is achieved by employing Intel® i82567V (PHY) + Intel® i82583V 10/100/1000Base-TX Ethernet controllers. To meet demanding expansion requirements the PCM-LN02 offers PCI, PCMCIA, PC/104+ (ISA+PCI), and two Mini Cards (1st: Full size+ SIM; 2nd: Half-size).
Compact Board PCM-LN02 1.2 Features Onboard Intel® Atom™ N455/D525 Processors Intel® ICH8M Onboard Memory 2GB Integrated Graphic Supports 18-bit or 24-bit LVDS Panel, Shared Memory Up To 384MB With DVMT 4.0 18-bit LVDS, 24-bit LVDS Intel® i82567V (PHY)+Intel® i82583V, 10/100/1000Base-TX PC/104+ (ISA+PCI), CompactFlash™, PCMCIA (x1 Slot), EIDE x 1 (Optional), SATA 3.
Compact Board PCM-LN02 1.
Compact Board Operating Humidity PCM-LN02 0%~90% relative humidity, non-condensing Display: Supports CRT/LCD simultaneous/ dual view display Chipset Intel® Atom™ processor integrated Memory Shared system memory up to 384 MB w/ DVMT4.0 Resolutions Up to 1366x768 @18bpp for LVDS; Up to 2048x1536 @ 60Hz for CRT LCD Interface LVDS (18-bit or 24-bit) Storage CompactFlash™ x 1, SATA 3.
Compact Board PCM-LN02 Chapter 2 Quick Installation Guide Chapter 2 Quick Installation Guide 2-1
Compact Board PCM-LN02 2.1 Safety Precautions Always completely disconnect the power cord from your board whenever you are working on it. Do not make connections while the power is on, because a sudden rush of power can damage sensitive electronic components. Always ground yourself to remove any static charge before touching the board. Modern electronic devices are very sensitive to static electric charges. Use a grounding wrist strap at all times.
Compact Board PCM-LN02 2.
Compact Board Chapter 2 Quick Installation Guide 2-4 PCM-LN02
Compact Board PCM-LN02 2.
Compact Board Chapter 2 Quick Installation Guide 2-6 PCM-LN02
Compact Board PCM-LN02 2.4 List of Jumpers The board has a number of jumpers that allow you to configure your system to suit your application.
Compact Board PCM-LN02 2.5 List of Connectors The board has a number of connectors that allow you to configure your system to suit your application.
Compact Board PCM-LN02 CN23 COM Port 2 Connector CN24 PC-104 Slot / ISA Interface CN25 TTL LCD Connector ( Optional ) CN26 COM Port 1 Connector CN27 LVDS Connector CN28 PS/2 Keyboard & Mouse Connector CN29 LCD Inverter Connector CN30 Parallel Port Connector CN31 CRT Display Connector CN32 System Fan Connector CN33 Digital I/O Connector CN34 Front Panel CN35 PCMCIA Slot CFD1 Compact Flash Disk PCIE1 Mini-Card Slot #1 PCIE2 Mini-Card Slot #2 Chapter 2 Quick Installation Guide
Compact Board PCM-LN02 2.6 Setting Jumpers You configure your card to match the needs of your application by setting jumpers. A jumper is the simplest kind of electric switch. It consists of two metal pins and a small metal clip (often protected by a plastic cover) that slides over the pins to connect them. To “close” a jumper you connect the pins with the clip. To “open” a jumper you remove the clip. Sometimes a jumper will have three pins, labeled 1, 2 and 3.
Compact Board PCM-LN02 2.7 AT/ATX Selection (JP1) JP1 Function 1-2 AT 2-3 ATX (default) 2.8 Clear CMOS (JP2) JP2 Function 1-2 Normal (default) 2-3 Clear CMOS 2.9 COM1 RI/+5V/+12V Selection (JP3) JP3 Function 1-2 +12V 3-4 +5V 5-6 RI (default) 2.10 LCD Operating Voltage Selection (JP4) JP4 Function 1-2 +5V 2-3 +3.3V (default) 2.
Compact Board PCM-LN02 2.12 LCD Inverter Voltage Selection (JP6) JP6 Function 1-2 +12V 2-3 +5V (default) 2.13 Audio Line-In/Out and MIC Selection (CN1) Pin Signal Pin Signal 1 MIC_R 2 MIC_L 3 Ground 4 N/C 5 LINE IN_L 6 N/C 7 LINE IN_R 8 N/C 9 Ground 10 N/C 11 LINE OUT_L 12 LINE OUT_R 13 Ground 14 Ground 2.
Compact Board PCM-LN02 2.15 SATA 2 Connector (CN3) Pin Signal 1 Ground 2 TX1+ 3 TX1 4 Ground 5 RX1- 6 RX1+ 7 Ground 2.16 Stereo Audio Output Connector (CN4) Pin Signal Pin Signal 1 SPK OUT_R+ 2 SPK OUT_R- 3 SPK OUT_L+ 4 SPK OUT_L- 2.17 RJ-45 Ethernet #1 (CN5) Pin Signal Pin Signal R1 MDIO0+ R2 MDIO0- R3 MDIO1+ R4 MDIO1- R5 TCD0 R6 TCD1 R7 MDIO2+ R8 MDIO2- R9 MDIO3+ R10 MDIO3- L1 ACT_LED L2 +3.3 Volt.
Compact Board PCM-LN02 2.18 RJ-45 Ethernet #2 (CN6) Pin Signal Pin Signal R1 GPHY_MDIO0+ R2 GPHY_MDIO0- R3 GPHY_MDIO1+ R4 GPHY_MDIO1- R5 TCD0 R6 TCD1 R7 GPHY_MDIO2+ R8 GPHY_MDIO2- R9 GPHY_MDIO3+ R10 GPHY_MDIO3- L1 ACT_LED L2 +3.3 Volt. L3 SPD100_LED L4 SPD1K_LED 2.19 Voltage Input Connector (CN7) Pin Signal 1 +12 Volt. 2 Ground 3 Ground 4 N/C 2.20 ATX Power Connector (CN8) Pin Signal Pin Signal 1 N/C 2 N/C 3 Ground 4 +5 Volt. 5 Ground 6 +5 Volt.
Compact Board PCM-LN02 13 Ground 14 PSON# 15 Ground 16 Ground 17 Ground 18 N/C 19 +5 Volt. 20 +5 Volt. 2.21 +5V/ +12V Output Connector for SATA HDD (CN9) Pin Signal 1 +12 Volt. 2 Ground 3 Ground 4 +5 Volt. 2.22 IDE Connector (CN10) Pin Signal Pin Signal 1 IDERST# 2 Ground 3 D7 4 D8 5 D6 6 D9 7 D5 8 D10 9 D4 10 D11 11 D3 12 D12 13 D2 14 D13 15 D1 16 D14 17 D0 18 D15 19 Ground 20 N/C / +5 Volt.
Compact Board PCM-LN02 23 IOW# 24 Ground 25 IOR# 26 Ground 27 IORDY 28 Ground 29 DACK# 30 Ground 31 IRQ14 32 N/C 33 A1 34 Cable Detect 35 A0 36 A2 37 CS#1 38 CS#3 39 ACT# 40 Ground 2.23 USB Port 1,2 Connector (CN11) Pin Signal Pin Signal 1 +5 Volt. Standby 2 Ground 3 Data0- 4 Ground 5 Data0+ 6 Data1+ 7 Ground 8 Data1- 9 Ground 10 +5 Volt. Standby 2.24 CPU Fan Connector (CN12) Pin Signal 1 Ground 2 +5 Volt. (Optional) / +12 Volt.
Compact Board PCM-LN02 2.25 USB Port 3,4 Connector (CN13) Pin Signal Pin Signal 1 +5 Volt. Standby 2 Ground 3 Data2- 4 Ground 5 Data2+ 6 Data3+ 7 Ground 8 Data3- 9 Ground 10 +5 Volt. Standby 2.26 USB Port 5,6 Connector (CN14) Pin Signal Pin Signal 1 +5 Volt. Standby 2 Ground 3 Data4- 4 Ground 5 Data4+ 6 Data5+ 7 Ground 8 Data5- 9 Ground 10 +5 Volt. Standby 2.27 PCI-104 Connector (CN15) Standard Specifications 2.
Compact Board PCM-LN02 2.29 COM Port 6 Connector (CN18) Pin Signal Pin Signal 1 DCDF 2 RXF 3 TXF 4 DTRF 5 Ground 6 DSRF 7 RTSF 8 CTSF 9 RIF 10 N/C 2.30 PCI Slot (CN19) Standard Specifications 2.31 COM Port 5 Connector (CN20) Pin Signal Pin Signal 1 DCDE 2 RXE 3 TXE 4 DTRE 5 Ground 6 DSRE 7 RTSE 8 CTSE 9 RIE 10 N/C 2.
Compact Board 9 RID PCM-LN02 10 N/C 2.33 COM Port 3 Connector (CN22) Pin Signal Pin Signal 1 DCDC 2 RXC 3 TXC 4 DTRC 5 Ground 6 DSRC 7 RTSC 8 CTSC 9 RIC 10 N/C 2.34 COM Port 2 Connector (CN23) Pin Signal Pin Signal 1 DCDB 2 RXB 3 TXB 4 DTRB 5 Ground 6 DSRB 7 RTSB 8 CTSB 9 RIB 10 N/C 2.
Compact Board PCM-LN02 6 D3 DRQ2 7 D2 -12V 8 D1 ENDXFR* 9 D0 +12V 10 IOCHRDY GND/KEY 11 AEN SMEMW* 12 A19 SMEMR* 13 A18 IOW* 14 A17 IOR* 15 A16 DACK3* 16 A15 DRQ3 17 A14 DACK1* 18 A13 DRQ1 19 A12 REFRESH* 20 A11 SYSCLK 21 A10 IRQ7 22 A9 IRQ6 23 A8 IRQ5 24 A7 IRQ4 25 A6 IRQ3 26 A5 DACK2* 27 A4 TC 28 A3 BALE 29 A2 +5V 30 A1 OSC Chapter 2 Quick Installation Guide 2-20
Compact Board PCM-LN02 31 A0 GND 32 GND GND Pin C D 1 GND GND 2 MEMCS16* SBHE* 3 IOCS16* LA23 4 IRQ10 LA22 5 IRQ11 LS21 6 IRQ12 LS20 7 IRQ13 LS19 8 IRQ14 LA18 9 DACK0* LA17 10 DRQ0 MEMR* 11 DACK5* MEMMW* 12 DRQ5 SD8 13 DACK6* SD9 14 DRQ6 SD10 15 DACK7* SD11 16 DRQ7 SD12 17 +5V SD13 18 MASTER* SD14 19 GND SD15 20 GND GND/KEY J2/P2 Chapter 2 Quick Installation Guide 2-21
Compact Board PCM-LN02 2.36 TTL LCD Connector (CN25) Pin Signal Pin Signal 1 LCD Volt. 2 LCD Volt. 3 Ground 4 Ground 5 LCD Volt. 6 LCD Volt.
Compact Board PCM-LN02 2.37 COM Port 1 Connector (CN26) COM 1/RS-232 Mode Pin Signal Pin Signal 1 DCDA 2 RXA 3 TXA 4 DTRA 5 Ground 6 DSRA 7 RTSA 8 CTSA 9 RIA / +5 Volt. / +12 Volt. 10 N/C COM1/RS-422 Pin Signal Pin Signal 1 TXA- 2 RXA+ 3 TXA+ 4 RXA- 5 Ground 6 N/C 7 N/C 8 N/C 9 N/C / +5 Volt. / +12 Volt. 10 N/C COM1/RS-485 Pin Signal Pin Signal 1 TXA- 2 N/C 3 TXA+ 4 N/C 5 Ground 6 N/C 7 N/C 8 N/C 9 N/C / +5 Volt. / +12 Volt.
Compact Board PCM-LN02 2.38 LVDS Connector (CN27) Pin Signal Pin Signal 1 Back-Light Enable 2 Back-Light Control 3 LCD Volt. 4 Ground 5 LA_CLK# 6 LA_CLK 7 LCD Volt. 8 Ground 9 LA_DATA#_0 10 LA_DATA_0 11 LA_DATA#_1 12 LA_DATA_1 13 LA_DATA#_2 14 LA_DATA_2 15 LA_DATA#_3 16 LA_DATA_3 17 LVDS_DATA / N/C 18 LVDS_CLK / N/C 19 N/C 20 N/C 21 N/C 22 N/C 23 N/C 24 N/C 25 N/C 26 N/C 27 LCD Volt. 28 Ground 29 N/C 30 N/C 2.
Compact Board PCM-LN02 2.40 LCD Inverter Connector (CN29) Pin Signal 1 +5 Volt./ +12 Volt. 2 Brightness Control 3 Ground 4 Ground 5 Backlight Enable 2.
Compact Board PCM-LN02 2.42 CRT Display Connector (CN31) Pin Signal Pin Signal 1 RED 2 +5 Volt. 3 GREEN 4 Ground 5 BLUE 6 N/C 7 N/C 8 DDCDATA 9 Ground 10 HSYNC 11 CRT_PLUG# 12 VSYNC 13 Ground 14 DDCCLK 15 Ground 16 Ground 2.43 System Fan Connector (CN32) Pin Signal 1 Ground 2 +5 Volt. (Optional) / +12 Volt. 3 Fan Sense 2.
Compact Board PCM-LN02 Digital I/O Address is A41H.
Compact Board PCM-LN02 3 PDD4 28 PDD12 4 PDD5 29 PDD13 5 PDD6 30 PDD14 6 PDD7 31 PDD15 7 PDCS#1 32 PDCS#3 8 Ground 33 Ground 9 Ground 34 PDIOR# 10 Ground 35 PDIOW# 11 Ground 36 +3.3 Volt. 12 Ground 37 INT_IRQ14 13 +3.3 Volt. 38 +3.3 Volt. 14 Ground 39 CSEL# 15 Ground 40 N/C 16 Ground 41 IDERST# 17 Ground 42 PIORDY 18 PDA2 43 N/C 19 PDA1 44 +3.3 Volt.
Compact Board PCM-LN02 2.48 Mini-Card Slot #1 (PCIE1) Pin Signal Pin Signal 1 PCIE_WAKE# 2 +3.3 Volt. Standby 3 N/C 4 Ground 5 N/C 6 +1.5 Volt. 7 CLKREQ# 8 UIM_PWR 9 Ground 10 UIM_DATA 11 MCARD_CLK1# 12 UIM_CLK 13 MCARD_CLK1 14 UIM_RESET 15 Ground 16 UIM_VPP 17 N/C 18 Ground 19 N/C 20 W_DISABLE#1 21 Ground 22 PCIE_RST# 23 PCIE_RXN1 24 +3.3 Volt. Standby 25 PCIE_RXP1 26 Ground 27 Ground 28 +1.5 Volt.
Compact Board PCM-LN02 45 N/C 46 N/C 47 N/C 48 +1.5 Volt. 49 N/C 50 Ground 51 N/C 52 +3.3 Volt. Standby 2.49 Mini-Card Slot #2 (PCIE2) Pin Signal Pin Signal 1 PCIE_WAKE# 2 +3.3 Volt. Standby 3 N/C 4 Ground 5 N/C 6 +1.5 Volt. 7 CLKREQ# 8 N/C 9 Ground 10 N/C 11 MCARD_CLK2# 12 N/C 13 MCARD_CLK2 14 N/C 15 Ground 16 N/C 17 N/C 18 Ground 19 N/C 20 W_DISABLE#2 21 Ground 22 PCIE_RST# 23 PCIE_RXN2 24 +3.3 Volt.
Compact Board PCM-LN02 37 Ground 38 USB_Data9+ 39 +3.3 Volt. Standby 40 Ground 41 +3.3 Volt. Standby 42 N/C 43 Ground 44 N/C 45 N/C 46 N/C 47 N/C 48 +1.5 Volt. 49 N/C 50 Ground 51 N/C 52 +3.3 Volt.
Compact Board PCM-LN02 Below Table for China RoHS Requirements 产品中有毒有害物质或元素名称及含量 AAEON Main Board/ Daughter Board/ Backplane 有毒有害物质或元素 部件名称 铅 汞 镉 六价铬 多溴联苯 多溴二苯醚 (Pb) (Hg) (Cd) (Cr(VI)) (PBB) (PBDE) × ○ ○ ○ ○ ○ × ○ ○ ○ ○ ○ 印刷电路板 及其电子组件 外部信号 连接器及线材 O：表示该有毒有害物质在该部件所有均质材料中的含量均在 SJ/T 11363-2006 标准规定的限量要求以下。 X：表示该有毒有害物质至少在该部件的某一均质材料中的含量超出 SJ/T 11363-2006 标准规定的限量要求。 备注：此产品所标示之环保使用期限，系指在一般正常使用状况下。 Chapter 2 Quick Installation Guide 2-32
Compact Board PCM-LN02 Chapter 3 AMI BIOS Setup Chapter 3 AMI BIOS Setup 3-1
Compact Board 3.1 PCM-LN02 System Test and Initialization These routines test and initialize board hardware. If the routines encounter an error during the tests, you will either hear a few short beeps or see an error message on the screen. There are two kinds of errors: fatal and non-fatal. The system can usually continue the boot up sequence with non-fatal errors. System configuration verification These routines check the current system configuration against the values stored in the CMOS memory.
Compact Board 3.2 PCM-LN02 AMI BIOS Setup AMI BIOS ROM has a built-in Setup program that allows users to modify the basic system configuration. This type of information is stored in battery-backed CMOS RAM so that it retains the Setup information when the power is turned off. Entering Setup Power on the computer and press or immediately. This will allow you to enter Setup. Main Set the date, use tab to switch between date elements.
Compact Board PCM-LN02 Chapter 4 Driver Installation Chapter 4 Driver Installation 4-1
Compact Board PCM-LN02 The PCM-LN02 comes with an AutoRun CD-ROM that contains all drivers and utilities that can help you to install the driver automatically. Insert the driver CD, the driver CD-title will auto start and show the installation guide. If not, please follow the sequence below to install the drivers.
Compact Board PCM-LN02 4.1 Installation Insert the PCM-LN02 CD-ROM into the CD-ROM drive and install the drivers from Step 1 to Step 5 in order. Step 1 – Install Chipset Driver 1. Click on the Step 1 - Intel Chipset Software Installation Utility folder 2. Double click on infinst_autol file 3. Follow the instructions that the window shows 4. The system will help you install the driver automatically Step 2 – Install VGA Driver 1.
Compact Board PCM-LN02 4. The system will help you install the driver automatically Step 4 –Install Audio Driver 1. Click on the Step 4 – Realtek HD Audio Codec folder 2. Choose the OS your system is. 3. Double click on Setup.exe file located in each OS folder 4. Follow the instructions that the window shows 5. The system will help you install the driver automatically Step 5 – Install TPM Driver (Optional) 1. Click on the Step 5 – Infineon TPM (Option) folder 2. Double click on Setup.exe file 3.
Compact Board PCM-LN02 Appendix A Programming the Watchdog Timer Appendix A Programming the Watchdog Timer A - 1
Compact Board PCM-LN02 A.1 Programming PCM-LN02 utilizes ITE 8712 chipset as its watchdog timer controller. ( K version ) Below are the procedures to complete its configuration and the AAEON intial watchdog timer program is also attached based on which you can develop customized program to fit your application. Configuring Sequence Description After the hardware reset or power-on reset, the ITE 8712 enters the normal mode with all logical devices disabled except KBC.
Compact Board PCM-LN02 Exit the MB PnP Mode. Undesired result may occur if the MB PnP Mode is not exited normally. (1) Enter the MB PnP Mode To enter the MB PnP Mode, four special I/O write operations are to be performed during Wait for Key state. To ensure the initial state of the key-check logic, it is necessary to perform four write opera-tions to the Special Address port (2EH). Two different enter keys are provided to select configuration ports (2Eh/2Fh) of the next step.
Compact Board PCM-LN02 require the software to clear them. Bit 7-2 1 0 Description Reserved Returns to the Wait for Key state. This bit is used when the configuration sequence is completed. Resets all logical devices and restores configuration registers to their power-on states.
Compact Board PCM-LN02 WatchDog Timer Time-out Value (LSB) Register (Index=73h, Default=00h) Bit 7-0 Description WDT Time-out value 7-0 WatchDog Timer Time-out Value (MSB) Register (Index=74h, Default=00h) Bit 7-0 Description WDT Time-out value 15-8 Appendix A Programming the Watchdog Timer A - 5
Compact Board PCM-LN02 A.2 ITE8712 Watchdog Timer Initial Program .MODEL SMALL .CODE Main: CALL Enter_Configuration_mode CALL Check_Chip mov cl, 7 call Set_Logic_Device ;time setting mov cl, 10 ; 10 Sec dec al Watch_Dog_Setting: ;Timer setting mov al, cl mov cl, 73h call Superio_Set_Reg ;Clear by keyboard or mouse interrupt mov al, 0f0h mov cl, 71h call Superio_Set_Reg ;unit is second.
Compact Board PCM-LN02 ; game port enable mov cl, 9 call Set_Logic_Device Initial_OK: CALL Exit_Configuration_mode MOV AH,4Ch INT 21h Enter_Configuration_Mode PROC NEAR MOV SI,WORD PTR CS:[Offset Cfg_Port] MOV DX,02Eh MOV CX,04h Init_1: MOV AL,BYTE PTR CS:[SI] OUT DX,AL INC SI LOOP Init_1 RET Enter_Configuration_Mode ENDP Exit_Configuration_Mode PROC NEAR MOV AX,0202h CALL Write_Configuration_Data Appendix A Programming the Watchdog Timer A - 7
Compact Board PCM-LN02 RET Exit_Configuration_Mode ENDP Check_Chip PROC NEAR MOV AL,20h CALL Read_Configuration_Data CMP AL,87h JNE Not_Initial MOV AL,21h CALL Read_Configuration_Data CMP AL,12h JNE Not_Initial Need_Initial: STC RET Not_Initial: CLC RET Check_Chip ENDP Read_Configuration_Data PROC NEAR MOV DX,WORD PTR CS:[Cfg_Port+04h] OUT DX,AL Appendix A Programming the Watchdog Timer A - 8
Compact Board PCM-LN02 MOV DX,WORD PTR CS:[Cfg_Port+06h] IN AL,DX RET Read_Configuration_Data ENDP Write_Configuration_Data PROC NEAR MOV DX,WORD PTR CS:[Cfg_Port+04h] OUT DX,AL XCHG AL,AH MOV DX,WORD PTR CS:[Cfg_Port+06h] OUT DX,AL RET Write_Configuration_Data ENDP Superio_Set_Reg proc near push ax MOV DX,WORD PTR CS:[Cfg_Port+04h] mov al,cl out dx,al pop ax inc dx out dx,al ret Superio_Set_Reg endp.
Compact Board PCM-LN02 Set_Logic_Device proc near push ax push cx xchg al,cl mov cl,07h call Superio_Set_Reg pop cx pop ax ret Set_Logic_Device endp ;Select 02Eh->Index Port, 02Fh->Data Port Cfg_Port DB 087h,001h,055h,055h DW 02Eh,02Fh END Main Note: Interrupt level mapping 0Fh-Dh: not valid 0Ch: IRQ12 . .
Compact Board PCM-LN02 Appendix B I/O Information Appendix B I/O Information B - 1
Compact Board PCM-LN02 B.
Compact Board PCM-LN02 B.3 IRQ Mapping Chart IRQ0 System Timer IRQ1 IRQ2 IRQ3 IRQ4 IRQ5 IRQ6 IRQ7 Keyboard Cascade to IRQ Controller COM2 COM1 COM3 Reserved COM4 IRQ8 System CMOS/ Real time clock IRQ9 ACPI IRQ10 COM5 IRQ11 COM6 IRQ12 PS/2 mouse IRQ13 FPU IRQ14 Primary IDE IRQ15 Secondary IDE B.
Compact Board PCM-LN02 Appendix C Mating Connecotor Appendix C Mating Connector C - 1
Compact Board PCM-LN02 C.1 List of Mating Connectors and Cables The table notes mating connectors and available cables.
Compact Board CN22 CN23 CN25 CN26 CN27 CN28 CN29 CN30 CN31 CN32 CN33 BAT1 Serial Port 3 Connector Serial Port 2 Connector TTL LCD Connector Serial Port 1 Connector LVDS Connector PS/2 Keyboard & Mouse Inverter Connector Parallel Port Connector CRT Connector CPU Fan Connector Digital I/O Connector External RTC Connector PCM-LN02 Molex 87831-10 Molex 87831-10 HIROSE Molex HIROSE Wafer Molex HR Serial Port 1701100206 Cable Serial Port 1701100206 Cable DF13-40DS-1.
Compact Board PCM-LN02 Appendix D Ordering Information Appendix D Ordering Information D - 1
Compact Board PCM-LN02 D.1 Ordering Information Model TF-PCM-LN02 TF-PCM-LN02 TF-PCM-LN02 TF-PCM-LN02 Number -A1.0 -A1.0-01 -A1.0-02 -A1.
