Compact Board PCM-QM77 PCM-QM77 Intel® 3rd Generation CoreTM i7/ i5/ i3/ Celeron® Processor Intel® QM77/HM76 Chipset 10/100/1000Base-TX LANs 4 USB 3.0, 4 USB2.0, 10 COM 16-bit Digital I/O 2 SATA 6.0Gb/s (Optional RAID) 1 CFast , 1 Mini Card, LPC PCM-QM77 Manual 1st Ed.
Compact Board PCM-QM77 Copyright Notice This document is copyrighted, 2013. All rights are reserved. The original manufacturer reserves the right to make improvements to the products described in this manual at any time without notice. No part of this manual may be reproduced, copied, translated, or transmitted in any form or by any means without the prior written permission of the original manufacturer. Information provided in this manual is intended to be accurate and reliable.
Compact Board PCM-QM77 Acknowledgments All other products’ name or trademarks are properties of their respective owners. AMI is a trademark of American Megatrends Inc. CFast™ is a trademark of the Compact Flash Association. Intel® and Core™ are trademarks of Intel® Corporation. Microsoft Windows® is a registered trademark of Microsoft Corp. ITE is a trademark of Integrated Technology Express, Inc.
Compact Board PCM-QM77 Packing List Before you begin installing your card, please make sure that the following materials have been shipped: 1 17592QM772 Cooler 1 DVD-ROM for Manual (in PDF Format) and Drivers 1 PCM-QM77 1 1702150155 SATA cable 1 1709070500 SATA Power cable 1 9657666600 Jumper Cap If any of these items should be missing or damaged, please contact your distributor or sales representative immediately.
Compact Board PCM-QM77 Contents Chapter 1 General Information 1.1 Introduction................................................................ 1-2 1.2 Features .................................................................... 1-3 1.3 Specifications ............................................................ 1-4 Chapter 2 Quick Installation Guide 2.1 Safety Precautions .................................................. 2-2 2.2 Location of Connectors and Jumpers ....................... 2-3 2.
Compact Board PCM-QM77 2.15 AT/ATX Power Supply Mode Selection (JP8)....... 2-15 2.16 Front Panel Connector (JP9) ................................ 2-16 2.17 Clear ME Jumper (JP10)....................................... 2-16 2.18 Clear CMOS Jumper (JP10) ................................. 2-17 2.19 Touch Screen 4/5-Wire Mode Selection (JP11).... 2-17 2.20 DVI Connector (CN1) ............................................ 2-17 2.21 Stereo Audio Output Connector (CN2) ................. 2-19 2.
Compact Board PCM-QM77 2.40 LVDS Port 1 (CN21).............................................. 2-39 2.41 LPC Port (CN22) ................................................... 2-41 2.42 COM Port 6 (CN23)............................................... 2-42 2.36 COM Port 5 (CN24)............................................... 2-44 2.37 PCI Slot (CN25)..................................................... 2-45 2.38 COM Port 8 (CN26)............................................... 2-45 2.39 COM Port 7 (CN27)........
Compact Board PCM-QM77 2.58 Touch Screen Connector (CN48).......................... 2-59 2.59 CPU FAN Connector (CN49) ................................ 2-61 2.60 UIM Card Connector (CN50)................................. 2-61 2.61 Mini-Card Slot (CN51) ........................................... 2-62 2.62 CFast Slot (CN52) ................................................. 2-65 Chapter 3 AMI BIOS Setup 3.1 System Test and Initialization. .................................. 3-2 3.2 AMI BIOS Setup ........
Compact Board PCM-QM77 D.2 Setting AHCI ......................................................... D-8 Appendix E Electrical Specifications for I/O Ports E.1 Electrical Specifications for I/O Ports.....................E-2 Appendix F Digital I/O F.1 Digital I/O ...............................................................
Compact Board PCM-QM77 Chapter 1 General Information Chapter 1 General Information 1- 1
Compact Board PCM-QM77 1.1 Introduction The PCM-QM77 supports Intel® 3rd Generation Intel® Core™ i7/i5/i3/Celeron® processor which when paired with the Intel® QM77/HM76 chipset offers a high performance computing platform with low power consumption. This new product supports two DDR3/L SODIMMs at speed of 1333/1600 MHz, up to 16 GB. One CFast™ and two SATA 6.0Gb/s (Optional RAID) interfaces provide ample storages. With dual Gigabit Ethernet, ten COM ports, four USB3.0 and four USB2.
Compact Board PCM-QM77 1.2 Features Intel® 3rd Generation Intel® Core™ i7/i5/i3/Celeron® processor Intel® QM77/HM76 204-pin DDR3 SODIMM x 2, DDR3/L 1333/1600, up to 16GB Gigabit Ethernet x 2 VGA, DVI, Dual LVDS LCD by CH7511 2CH Audio SATA 6.0Gb/s x 2 (Optional RAID), CFast™ x 1, mSATA x 1 USB3.0 x 4, USB2.
Compact Board PCM-QM77 1.3 Specifications System From Factor 5.
Compact Board PCM-QM77 32°F~140°F (0°C~60°C) Operating Temperature Storage Temperature -40°F~176°F (-40°C~80°C) Operating Humidity 0% ~ 90% relative humidity, non-condensing Display: Supports CRT/LCD, DVI/LCD simultaneous / dual view displays Intel® QM77/HM76 integrated Chipset Memory Shared system memory up to 512MB Resolution up to 2048 x 1536 for VGA Up to 1920 x 1200 for LVDS LCD, DVI DVI I/O: Fintek 81866 Storage Serial Port DVI-I x 1 SATA 6.
Compact Board PCM-QM77 Digital I/O 16-bit Programmable Audio Line-in, Line-out, Mic-in Chapter 1 General Information 1-6
Compact Board PCM-QM77 Chapter 2 Quick Installation Guide Chapter 2 Quick Installation Guide 2-1
Compact Board PCM-QM77 2.1 Safety Precautions Always completely disconnect the power cord from your board whenever you are working on it. Do not make connections while the power is on, because a sudden rush of power can damage sensitive electronic components. Always ground yourself to remove any static charge before touching the board. Modern electronic devices are very sensitive to static electric charges. Use a grounding wrist strap at all times.
Compact Board PCM-QM77 2.
Compact Board Solder Side Chapter 2 Quick Installation Guide 2-4 PCM-QM77
Compact Board PCM-QM77 2.
Compact Board Solder Side Chapter 2 Quick Installation Guide 2-6 PCM-QM77
Compact Board PCM-QM77 2.4 List of Jumpers The board has a number of jumpers that allow you to configure your system to suit your application.
Compact Board PCM-QM77 2.5 List of Connectors The board has a number of connectors that allow you to configure your system to suit your application.
Compact Board PCM-QM77 CN20 COM Port 3 CN21 LVDS Port 1 CN22 LPC Port CN23 COM Port 6 CN24 COM Port 5 CN25 PCI Slot CN26 COM Port 8 CN27 COM Port 7 CN28 PCI-Express［x16］Slot CN29 DDR3 SO-DIMM Channel B Slot CN30 DDR3 SO-DIMM Channel A Slot CN31 COM Port 10 CN32 COM Port 9 CN34 USB 3.0 Ports 1 and 2 CN35 USB 3.0 Ports 3 and 4 CN36 USB 2.0 Ports 5 and 6 CN37 USB 2.
Compact Board PCM-QM77 CN46 Digital IO Port 1 Connector CN47 Digital IO Port 2 Connector CN48 Touch Screen Connector (Optional) CN49 CPU Fan Connector CN50 UIM Card Connector CN51 Mini-Card Slot CN52 CFast Slot Chapter 2 Quick Installation Guide 2-10
Compact Board PCM-QM77 2.6 Setting Jumpers You configure your card to match the needs of your application by setting jumpers. A jumper is the simplest kind of electric switch. It consists of two metal pins and a small metal clip (often protected by a plastic cover) that slides over the pins to connect them. To “close” a jumper you connect the pins with the clip. To “open” a jumper you remove the clip. Sometimes a jumper will have three pins, labeled 1, 2 and 3.
Compact Board PCM-QM77 2.7 LVDS Port 2 Operating VDD Selection (JP1) 1 3 5 2 4 6 1 3 5 +3.3V (Default) JP1 Function 2-4 +3.3V (Default) 4-6 +5V 2 4 6 +5V 2.8 LVDS Port 2 Backlight Inverter VCC Selection (JP1) 1 3 5 2 4 6 +12V JP1 Function 1-3 +12V 3-5 +5V (Default) 1 3 5 2 4 6 +5V (Default) 2.
Compact Board PCM-QM77 JP2 Function 1-2 VR Mode 2-3 PWM Mode (Default) 2.10 LVDS Port 2 Backlight Lightness Control Mode Selection (JP3) 1 2 3 1 2 3 VR Mode PWM Mode (Default) JP3 Function 1-2 VR Mode 2-3 PWM Mode (Default) Note: 1. When we use LVDS Port2 normal backlight type in PWM mode, the backlight level only supports 30%~100%. 2. When we use LVDS Port2 inverted backlight type in PWM mode, the backlight level only supports 0%~70%. 2.
Compact Board PCM-QM77 2.12 LVDS Port 1 Backlight Inverter VCC Selection (JP4) 1 3 5 2 4 6 1 3 5 +12V 2 4 6 +5V (Default) JP4 Function 1-3 +12V 3-5 +5V (Default) 2.
Compact Board PCM-QM77 2.14 COM2 Pin9 Function Selection (JP6) 1 3 5 1 3 5 2 4 6 1 3 5 2 4 6 Ring(Default) +12V JP6 Function 1-2 +12V 3-4 Ring (Default) 5-6 +5V 2 4 6 +5V 2.
Compact Board PCM-QM77 2.16 Front Panel Connector (JP9) 1 3 5 7 9 Pin Signal 1 PWR_BTN- 2 PWR_BTN+ 3 HDD_LED- 4 HDD_LED+ 5 SPEAKER- 6 SPEAKER+ 7 PWR_LED- 8 PWR_LED+ 9 H/W RESET- 10 H/W RESET+ 2 4 6 8 10 2.
Compact Board 1-3 Normal (Default) 3-6 Clear ME PCM-QM77 Note: Clear ME need to use two jumper and be set after clear COMS. 2.18 Clear CMOS Jumper (JP10) 1 3 5 2 4 6 1 3 5 Normal (Default) JP10 Function 2-4 Normal (Default) 4-6 Clear CMOS 2 4 6 Clear CMOS 2.19 Touch Screen 4/5-Wire Mode Selection (JP11) (Optional) 1 2 3 1 2 3 4-wire mode (Default) 5-wire mode JP11 Function 1-2 4-wire mode (Default) 2-3 5-wire mode 2.
Compact Board PCM-QM77 Pin Pin Name Signal Type 1 TMDS_DAT2+ DIFF 2 TMDS_DAT2- DIFF 3 GND GND 4 NC I/O 5 NC I/O 6 DVI_DDC_CLK I/O +5V 7 DVI_DDC_DATA I/O +5V 8 VSYNC OUT 9 TMDS_DAT1- DIFF 10 TMDS_DAT1+ DIFF 11 GND GND 12 TMDS_DAT3- DIFF 13 TMDS_DAT3+ DIFF 14 +5V PWR 15 GND GND 16 HPLG_DETECT IN 17 TMDS_DAT0- DIFF 18 TMDS_DAT0+ DIFF 19 GND GND Chapter 2 Quick Installation Guide 2-18 Signal Level +5V
Compact Board PCM-QM77 20 NC 21 NC 22 GND GND 23 TMDS_CLK+ DIFF 24 TMDS_CLK- DIFF C1 RED OUT C2 GREEN OUT C3 BLUE OUT C4 HSYNC OUT C5 GND_ANALOG GND 2.
Compact Board PCM-QM77 2.22 Ethernet#2 Connector (CN3) (Optional) MDI0+ MDI1+ GND MDI2+ MDI3+ 1 2 9 10 MDI0MDI1GND MDI2MDI3- Pin Pin Name Signal Type 1 MDI0+ DIFF 2 MDI0- DIFF 3 MDI1+ DIFF 4 MDI1- DIFF 5 GND GND 6 GND GND 7 MDI2+ DIFF 8 MDI2- DIFF 9 MDI3+ DIFF 10 MDI3- DIFF 2.
Compact Board PCM-QM77 Pin Pin Name Signal Type 1 MDI0+ DIFF 2 MDI0- DIFF 3 MDI1+ DIFF 4 MDI1- DIFF 5 GND GND 6 GND GND 7 MDI2+ DIFF 8 MDI2- DIFF 9 MDI3+ DIFF 10 MDI3- DIFF Signal Level 2.
Compact Board PCM-QM77 4 MDI2+ DIFF 5 MDI2- DIFF 6 MDI1- DIFF 7 MDI3+ DIFF 8 MDI3- DIFF 2.
Compact Board PCM-QM77 2.26 ATX Power Connector (CN7) PIN1 PIN12 PIN13 PIN24 Pin Pin Name Signal Type Signal Level 1 +3.3V PWR +3.3V 2 +3.3V PWR +3.3V 3 GND GND 4 +5V PWR 5 GND GND 6 +5V PWR 7 GND GND 8 PWR_OK 9 +5VSB PWR +5V 10 +12V PWR +12V 11 +12V PWR +12V 12 +3.3V PWR +3.3V 13 +3.3V PWR +3.
Compact Board PCM-QM77 16 PS_ON# 17 GND GND 18 GND GND 19 GND GND 20 NC 21 +5V PWR +5V 22 +5V PWR +5V 23 +5V PWR +5V 24 GND GND 2.
Compact Board PCM-QM77 2.28 LVDS Port 1 Inverter / Backlight Connector (CN9) 1 BLK_PWR 2 BKL_CONTROL 3 GND 4 GND 5 BKL_ENABLE Pin Pin Name Signal Type Signal Level 1 BKL_PWR PWR +5V / +12V 2 BKL_CONTROL OUT 3 GND GND 4 GND GND 5 BKL_ENABLE OUT +5V Note: LVDS1 BKL_PWR can be set to +5V or +12V by JP4. LVDS1 BKL_CONTROL can be set by JP2. 2.
Compact Board PCM-QM77 2 MIC_L IN 3 GND_AUDIO GND 4 CD_GND GND 5 LINE_L_IN IN 6 CD_L IN 7 LINE_R_IN IN 8 CD_GND GND 9 GND_AUDIO GND 10 CD_R IN 11 LEFT_OUT OUT 12 RIGHT_OUT OUT 13 GND_AUDIO GND 14 GND_AUDIO GND 2.
Compact Board PCM-QM77 5 GND GND 6 RED_GND_RTN GND 7 GREEN_GND_RTN GND 8 BLUE_GND_RTN GND 9 +5V PWR 10 GND GND 11 NC 12 DDC_DATA I/O 13 HSYNC OUT 14 VSYNC OUT 15 DDC_CLK I/O +5V +5V +5V 2.
Compact Board PCM-QM77 3 GREEN OUT 4 GND GND 5 BLUE OUT 6 NC 7 NC 8 DDC_DATA I/O 9 GND GND 10 HSYNC OUT 11 GND GND 12 VSYNC OUT 13 GND GND 14 DDC_CLK I/O 15 GND GND 16 GND GND +5V +5V 2.32 mSATA Slot (CN13) Pin Pin Name 1 NC 2 +3.3V 3 NC 4 GND Chapter 2 Quick Installation Guide 2-28 Signal Type Signal Level PWR +3.
Compact Board PCM-QM77 5 NC 6 +1.5V 7 NC 8 NC 9 GND 10 NC 11 NC 12 NC 13 NC 14 NC 15 GND 16 NC 17 NC 18 GND 19 NC 20 NC 21 GND 22 NC 23 SATA_TX+ DIFF 24 +3.3V PWR PWR +1.5V GND GND GND GND +3.
Compact Board PCM-QM77 25 SATA_TX- DIFF 26 GND GND 27 GND GND 28 +1.5V PWR 29 GND GND 30 SMB_CLK I/O 31 SATA_RX- DIFF 32 SMB_DATA I/O 33 SATA_RX+ DIFF 34 GND GND 35 GND GND 36 NC 37 GND 38 NC 39 +3.3V PWR 40 GND GND 41 +3.3V PWR 42 NC 43 GND 44 NC Chapter 2 Quick Installation Guide 2-30 +1.5V +3.3V +3.3V GND GND +3.3V +3.
Compact Board 45 NC 46 NC 47 NC 48 +1.5V 49 NC 50 GND 51 NC 52 +3.3V PCM-QM77 +1.5V PWR GND PWR +3.3V 2.
Compact Board PCM-QM77 2.
Compact Board PCM-QM77 Pin Pin Name Signal Type Signal Level 1 RS485_D- I/O ±5V 2 RS485_D+ I/O ±5V 3 NC 4 NC 5 GND 6 NC 7 NC 8 NC 9 NC/+5V/+12V 10 NC RS422_TXRS422_RX+ GND NC NC/+5V/+12V GND PWR 1 2 9 10 +5V/+12V RS422_TX+ RS422_RXNC NC NC RS-422 Pin Pin Name Signal Type Signal Level 1 RS422_TX- OUT ±5V 2 RS422_TX+ OUT ±5V 3 RS422_RX+ IN 4 RS422_RX- IN 5 GND GND Chapter 2 Quick Installation Guide 2-33
Compact Board 6 NC 7 NC 8 NC 9 NC/+5V/+12V 10 NC PCM-QM77 PWR +5V/+12V Note: COM2 RS-232/422/485 can be set by BIOS setting. Default is RS-232. COM2 Pin 9 function can be set by JP6. 2.
Compact Board PCM-QM77 2.36 Ethernet#2 LED Indicator (CN17) PIN1 PIN2 PIN3 PIN4 PIN5 PIN6 Pin Pin Name Signal Type Signal Level 1 ACT_LED+ PWR +5V 2 ACT_LED- OUT 3 100_LED+ PWR 4 100_LED- OUT 5 1000_LED+ PWR 6 1000_LED- OUT +5V +5V 2.
Compact Board PCM-QM77 2 BKL_CONTROL OUT 3 LCD_PWR PWR 4 GND GND 5 LVDS_A_CLK- DIFF 6 LVDS_A_CLK+ DIFF 7 LCD_PWR PWR 8 GND GND 9 LVDS_DA0- DIFF 10 LVDS_DA0+ DIFF 11 LVDS_DA1- DIFF 12 LVDS_DA1+ DIFF 13 LVDS_DA2- DIFF 14 LVDS_DA2+ DIFF 15 LVDS_DA3- DIFF 16 LVDS_DA3+ DIFF 17 DDC_DATA I/O +3.3V 18 DDC_CLK I/O +3.3V 19 LVDS_DB0- DIFF 20 LVDS_DB0+ DIFF 21 LVDS_DB1- DIFF Chapter 2 Quick Installation Guide 2-36 +3.3V/+5V +3.
Compact Board PCM-QM77 22 LVDS_DB1+ DIFF 23 LVDS_DB2- DIFF 24 LVDS_DB2+ DIFF 25 LVDS_DB3- DIFF 26 LVDS_DB3+ DIFF 27 LCD_PWR PWR 28 GND GND 29 LVDS_B_CLK- DIFF 30 LVDS_B_CLK+ DIFF +3.3V/+5V 2.
Compact Board PCM-QM77 7 RTS OUT 8 CTS IN 9 RI IN 10 NC ±9V 2.
Compact Board PCM-QM77 2.40 LVDS Port 1 (CN21) PIN 29 PIN 30 PIN 1 PIN 2 Pin Pin Name Signal Type 1 BKL_ENABLE OUT 2 BKL_CONTROL OUT 3 LCD_PWR PWR 4 GND GND 5 LVDS_A_CLK- DIFF 6 LVDS_A_CLK+ DIFF 7 LCD_PWR PWR 8 GND GND 9 LVDS_DA0- DIFF 10 LVDS_DA0+ DIFF 11 LVDS_DA1- DIFF Signal Level +3.3V/+5V +3.
Compact Board PCM-QM77 12 LVDS_DA1+ DIFF 13 LVDS_DA2- DIFF 14 LVDS_DA2+ DIFF 15 LVDS_DA3- DIFF 16 LVDS_DA3+ DIFF 17 DDC_DATA I/O +3.3V 18 DDC_CLK I/O +3.3V 19 LVDS_DB0- DIFF 20 LVDS_DB0+ DIFF 21 LVDS_DB1- DIFF 22 LVDS_DB1+ DIFF 23 LVDS_DB2- DIFF 24 LVDS_DB2+ DIFF 25 LVDS_DB3- DIFF 26 LVDS_DB3+ DIFF 27 LCD_PWR PWR 28 GND GND 29 LVDS_B_CLK- DIFF 30 LVDS_B_CLK+ DIFF +3.3V/+5V Note: LVDS1 LCD_PWR can be set to +3.3V or +5V by JP4.
Compact Board PCM-QM77 2.41 LPC Port (CN22) LAD0 LAD1 LAD2 LAD3 +3.3V LFRAME# LRESET# GND LCLK LDRQ0 LDRQ1 SERIRQ 1 12 Pin Pin Name Signal Type Signal Level 1 LAD0 I/O +3.3V 2 LAD1 I/O +3.3V 3 LAD2 I/O +3.3V 4 LAD3 I/O +3.3V 5 +3.3V PWR +3.3V 6 LFRAME# IN 7 LRESET# OUT 8 GND GND 9 LCLK OUT 10 LDRQ0 IN 11 LDRQ1 IN 12 SERIRQ I/O +3.3V +3.
Compact Board PCM-QM77 2.
Compact Board PCM-QM77 Pin Pin Name Signal Type Signal Level 1 RS485_D- I/O ±5V 2 RS485_D+ I/O ±5V 3 NC 4 NC 5 GND 6 NC 7 NC 8 NC 9 NC/+5V/+12V 10 NC RS422_TXRS422_RX+ GND NC NC/+5V/+12V GND PWR 1 2 9 10 +5V/+12V RS422_TX+ RS422_RXNC NC NC RS-422 Pin Pin Name Signal Type Signal Level 1 RS422_TX- OUT ±5V 2 RS422_TX+ OUT ±5V 3 RS422_RX+ IN 4 RS422_RX- IN 5 GND GND Chapter 2 Quick Installation Guide 2-43
Compact Board 6 NC 7 NC 8 NC 9 NC/+5V/+12V 10 NC PCM-QM77 PWR +5V/+12V Note: 1. COM6 RS-232/422/485 can be set by BIOS setting. Default is RS-232. 2. COM6 Pin 9 function can be set by JP5. 3. COM6/ IrDA Function can be set by BIOS setting. Default is COM6 Function. 2.
Compact Board 10 PCM-QM77 NC 2.37 PCI Slot (CN25) Standard specification 2.
Compact Board PCM-QM77 2.39 COM Port 7 (CN27) DCD TX GND RTS RI 1 2 9 10 RX DTR DSR CTS NC Pin Pin Name Signal Type 1 DCD IN 2 RX IN 3 TX OUT ±9V 4 DTR OUT ±9V 5 GND GND 6 DSR IN 7 RTS OUT 8 CTS IN 9 RI IN 10 NC 2.40 PCI-Express［x16］Slot (CN28) Standard specification 2.41 DDR3 SO-DIMM Channel B Slot (CN29) Standard specification 2.
Compact Board PCM-QM77 2.43 COM Port 10 (CN31) DCD TX GND RTS RI 1 2 9 10 RX DTR DSR CTS NC Pin Pin Name Signal Type Signal Level 1 DCD IN 2 RX IN 3 TX OUT ±9V 4 DTR OUT ±9V 5 GND GND 6 DSR IN 7 RTS OUT 8 CTS IN 9 RI IN 10 NC ±9V 2.
Compact Board PCM-QM77 1 DCD IN 2 RX IN 3 TX OUT ±9V 4 DTR OUT ±9V 5 GND GND 6 DSR IN 7 RTS OUT 8 CTS IN 9 RI IN 10 NC ±9V 2.45 USB 3.
Compact Board PCM-QM77 5 USB1_SSTX− DIFF 6 USB1_SSTX+ DIFF 7 GND GND 8 USB1_D- DIFF 9 USB1_D+ DIFF 10 NC 11 USB2_D+ DIFF 12 USB2_D- DIFF 13 GND GND 14 USB2_SSTX+ DIFF 15 USB2_SSTX− DIFF 16 GND GND 17 USB2_SSRX+ DIFF 18 USB2_SSRX− DIFF 19 +5VSB PWR +5V Chapter 2 Quick Installation Guide 2-49
Compact Board PCM-QM77 2.46 USB 3.
Compact Board PCM-QM77 15 USB4_SSTX− DIFF 16 GND GND 17 USB4_SSRX+ DIFF 18 USB4_SSRX− DIFF 19 +5VSB PWR +5V 2.47 USB 2.
Compact Board PCM-QM77 2.48 USB 2.0 Ports 7 and 8 (CN37) +5VSB USB7_DUSB7_D+ GND GND 1 2 9 10 GND GND USB8_D+ USB8_D+5VSB Pin Pin Name Signal Type Signal Level 1 +5VSB PWR +5V 2 GND GND 3 USB7_D- DIFF 4 GND GND 5 USB7_D+ DIFF 6 USB8_D+ DIFF 7 GND GND 8 USB8_D- DIFF 9 GND GND 10 +5VSB PWR +5V 2.
Compact Board PCM-QM77 Pin Pin Name Signal Type Signal Level 1 KB_ DATA I/O +5V 2 KB_CLK I/O +5V 3 GND GND 4 +5VSB PWR +5V 5 MS_DATA I/O +5V 6 MS_CLK I/O +5V 2.50 IrDA Connector (CN39) (Optional) +5V NC IRRX GND IRTX Pin Pin Name Signal Type Signal Level 1 +5V PWR +5V 2 NC 3 IRRX IN 4 GND GND 5 IRTX OUT Note: COM6 / IrDA Function can be set by BIOS setting. Default is COM6 Function.
Compact Board PCM-QM77 2.51 SATA Port 2 Connector (CN40) Pin 1 Pin 7 Pin Pin Name Signal Type 1 GND GND 2 SATA_TX+ DIFF 3 SATA_TX- DIFF 4 GND GND 5 SATA_RX- DIFF 6 SATA_RX+ DIFF 7 GND GND Signal Level 2.
Compact Board PCM-QM77 3 SATA_TX- DIFF 4 GND GND 5 SATA_RX- DIFF 6 SATA_RX+ DIFF 7 GND GND 2.53 +5V Output for SATA HDD (CN43) +5V GND Pin Pin Name Signal Type Signal Level 1 +5V PWR +5V 2 GND GND 2.54 LPT Connector (CN44) 1 2 AFD# ERROR# PRINT# SLIN# GND GND GND GND GND GND GND GND N.
Compact Board PCM-QM77 1 STROBE# IN 2 AFD# I/O 3 PD0 I/O 4 ERROR# IN 5 PD1 I/O 6 PRINT# I/O 7 PD2 I/O 8 SLIN# I/O 9 PD3 I/O 10 GND GND 11 PD4 I/O 12 GND GND 13 PD5 I/O 14 GND GND 15 PD6 I/O 16 GND GND 17 PD7 I/O 18 GND GND 19 ACK# IN 20 GND GND Chapter 2 Quick Installation Guide 2-56
Compact Board PCM-QM77 21 BUSY IN 22 GND GND 23 PE IN 24 GND GND 25 SLCT IN 26 NC 2.55 System Fan Connector (CN45) 3 2 1 FAN_TAC GND FAN_POWER Pin Pin Name Signal Type 1 GND GND 2 FAN_POWER PWR 3 FAN_TAC IN Signal Level +12V 2.
Compact Board DIO0 DIO2 DIO4 DIO6 +5V PCM-QM77 1 2 9 10 DIO1 DIO3 DIO5 DIO7 GND Pin Pin Name Signal Type Signal Level 1 DIO0 I/O +5V 2 DIO1 I/O +5V 3 DIO2 I/O +5V 4 DIO3 I/O +5V 5 DIO4 I/O +5V 6 DIO5 I/O +5V 7 DIO6 I/O +5V 8 DIO7 I/O +5V 9 +5V PWR +5V 10 GND GND 2.
Compact Board PCM-QM77 Pin Pin Name Signal Type Signal Level 1 DIO0 I/O +5V 2 DIO1 I/O +5V 3 DIO2 I/O +5V 4 DIO3 I/O +5V 5 DIO4 I/O +5V 6 DIO5 I/O +5V 7 DIO6 I/O +5V 8 DIO7 I/O +5V 9 +5V PWR +5V 10 GND GND 2.
Compact Board PCM-QM77 2 TOP IN 3 BOTTOM IN 4 LEFT IN 5 RIGHT IN 6 NC 7 NC 8 NC 9 NC 5-wire 5 Wires GND UL(Y) UR(H) LL(L) LR(X) SENSE(S) NC NC NC 1 9 Pin Pin Name Signal Type 1 GND GND 2 UL(Y) IN 3 UR(H) IN 4 LL(L) IN Chapter 2 Quick Installation Guide 2-60 Signal Level
Compact Board PCM-QM77 5 LR(X) IN 6 SENSE(S) IN 7 NC 8 NC 9 NC Note: Touch mode can be set by JP11 2.59 CPU FAN Connector (CN49) 4 3 2 FAN_TAC 1 GND FAN_POWER FAN_CTL Pin Pin Name Signal Type 1 GND GND 2 FAN_POWER PWR 3 FAN_TAC IN 4 FAN_CTL OUT Signal Level +12V +3.3V 2.
Compact Board PCM-QM77 Pin Pin Name Signal Type 1 UIM_PWR PWR 2 UIM_RST IN 3 UIM_CLK IN 4 GND GND 5 UIM_VPP PWR 6 UIM_DATA I/O Signal Level 2.61 Mini-Card Slot (CN51) Pin Pin Name Signal Type 1 PCIE_WAKE# IN 2 +3.3VSB PWR 3 NC 4 GND 5 NC 6 +1.5V PWR 7 PCIE_CLK_REQ# IN 8 UIM_PWR PWR 9 GND GND 10 UIM_DATA I/O 11 PCIE_REF_CLK- DIFF Chapter 2 Quick Installation Guide 2-62 Signal Level +3.3V GND +1.
Compact Board PCM-QM77 12 UIM_CLK IN 13 PCIE_REF_CLK+ DIFF 14 UIM_RST IN 15 GND GND 16 UIM_VPP PWR 17 NC 18 GND 19 NC 20 W_DISABLE# OUT 21 GND GND 22 PCIE_RST# OUT 23 PCIE_RX- DIFF 24 +3.3VSB PWR 25 PCIE_RX+ DIFF 26 GND GND 27 GND GND 28 +1.5V PWR 29 GND GND 30 SMB_CLK I/O 31 PCIE_TX- DIFF GND +3.3V +3.3V +3.3V +1.5V +3.
Compact Board PCM-QM77 32 SMB_DATA I/O 33 PCIE_TX+ DIFF 34 GND GND 35 GND GND 36 USB_D- DIFF 37 GND GND 38 USB_D+ DIFF 39 +3.3VSB PWR 40 GND GND 41 +3.3VSB PWR 42 NC 43 GND 44 NC 45 NC 46 NC 47 NC 48 +1.5V 49 NC 50 GND 51 NC Chapter 2 Quick Installation Guide 2-64 +3.3V +3.3V +3.3V GND PWR GND +1.
Compact Board 52 +3.3VSB PCM-QM77 PWR +3.3V Signal Level 2.
Compact Board PCM-QM77 PC9 NC PC10 NC PC11 NC PC12 NC PC13 +3.3V PWR +3.3V PC14 +3.3V PWR +3.
Compact Board PCM-QM77 Below Table for China RoHS Requirements 产品中有毒有害物质或元素名称及含量 AAEON Main Board/ Daughter Board/ Backplane 有毒有害物质或元素 部件名称 铅 汞 镉 六价铬 多溴联苯 多溴二苯醚 (Pb) (Hg) (Cd) (Cr(VI)) (PBB) (PBDE) × ○ ○ ○ ○ ○ × ○ ○ ○ ○ ○ 印刷电路板 及其电子组件 外部信号 连接器及线材 O：表示该有毒有害物质在该部件所有均质材料中的含量均在 SJ/T 11363-2006 标准规定的限量要求以下。 X：表示该有毒有害物质至少在该部件的某一均质材料中的含量超出 SJ/T 11363-2006 标准规定的限量要求。 备注：此产品所标示之环保使用期限，系指在一般正常使用状况下。 Chapter 2 Quick Installation Guide 2-67
Compact Board PCM-QM77 Chapter 3 AMI BIOS Setup Chapter 3 AMI BIOS Setup 3-1
Compact Board 3.1 PCM-QM77 System Test and Initialization These routines test and initialize board hardware. If the routines encounter an error during the tests, you will either hear a few short beeps or see an error message on the screen. There are two kinds of errors: fatal and non-fatal. The system can usually continue the boot up sequence with non-fatal errors. System configuration verification These routines check the current system configuration against the values stored in the CMOS memory.
Compact Board 3.2 PCM-QM77 AMI BIOS Setup AMI BIOS ROM has a built-in Setup program that allows users to modify the basic system configuration. This type of information is stored in battery-backed CMOS RAM so that it retains the Setup information when the power is turned off. Entering Setup Power on the computer and press or immediately. This will allow you to enter Setup. Main Set the date, use tab to switch between date elements.
Compact Board PCM-QM77 Setup Menu Setup submenu: Main Options summary: (default setting) System Date Day MM:DD:YYYY Change the month, year and century. The ‘Day’ is changed automatically. System Time HH : MM : SS Change the clock of the system.
Compact Board PCM-QM77 Setup submenu: Advanced Options summary: (default setting) ICC Spread Spectrum Disabled Enabled Spread Spectrum Support AAEON ICC Spread Spectrum 45 AAEON ICC Spread Spectrum default value ACPI Settings System ACPI Parameters S5 RTC Wake Settings Enable system to wake from S5 using RTC alarm.
Compact Board Trusted Computing Trusted Computing Settings CPU Configuration CPU Configuration Parameters Dynamic Digital IO Configuration DIO setting SATA Configuration SATA Device Options Settings Intel TXT(LT) Configuration Intel Trusted Execution Technology AMT Configuration AMT Configuration Parameters USB Configuration USB Configuration Parameters F81216 Second Super IO Configuration Second IO Configuration Parameters F81866 Super IO Configuration Super IO Configuration Parameters F81866 H/W Monitor
Compact Board PCM-QM77 ACPI Settings Options summary: (default setting) Suspend Disabled S1 only(CPU Stop Clock) ACPI Sleep State S3 only(Suspend to RAM) Both S1 and S3 available for OS to choose from Select the ACPI state used for System Suspend Chapter 3 AMI BIOS Setup 3-7
Compact Board PCM-QM77 RTC Wake Settings Options summary: (default setting) Wake system with Fixed Disabled Time Enabled Enable or disable System wake on alarm event. Wake up time is setting by following settings.
Compact Board Wake up minute 0-59 Wake up second 0-59 Wake system with Disabled Dynamic Time Enabled PCM-QM77 Enable or disable System wake on alarm event. Wake up time is current time + Increase minutes.
Compact Board PCM-QM77 Trusted Computing Options summary: (default setting) Security Device Support Disabled Enabled En/Disable TPM support. TPM State Disabled Enabled En/Disable TPM functionality. Pending TPM Operation None Enable Take Ownership Disable Take Ownership TPM Clear Select one-time TPM operation. Item value returns to ‘None’ after next POST.
Compact Board PCM-QM77 CPU Configuration Options summary: (default setting) Hyper-Threading Disabled Enabled En/Disable CPU Hyper-Threading function Active Processor Cores ALL 1 to Max CPU cores Number of CPU cores to be active.
Compact Board Dynamic Digital IO Configration Options summary: (default setting) Digital Port X(GPXX) Input Direction Output Set GPIOx as Input or Output Digital Port X(GPXX) Levels Hi Low Set GPIO output level when used as output pin Chapter 3 AMI BIOS Setup 3-12 PCM-QM77
Compact Board PCM-QM77 SATA Configuration Options summary: (default setting) SATA Controller(s) Disabled Enabled En/Disable SATA controller Configure SATA as IDE AHCI RAID Configure SATA controller operating as IDE/AHCI/RAID mode. SATA Controller Speed Gen1 Gen2 Gen3 Indicates the maximum speed the SATA controller can support.
Compact Board Port X PCM-QM77 Disabled Enabled En/Disable the selected port. Hot Plug Disabled Enabled En/Disable Hot Plug feature for specified port. Intel TXT (LT) Configuration Options summary: (default setting) Intel TXT(LT) Support Disabled Enabled En/Disable Intel TXT function. This function only can be enabled/disabled if SMX, VT-x and VT-d support are enabled prior to it.
Compact Board PCM-QM77 AMT Configuration Options summary: (default setting) Intel AMT Enabled Disabled En/Disable Intel® Active Management Technology BIOS Extension. Note: iAMT H/W is always enabled. This option just controls the BIOS extension execution.
Compact Board PCM-QM77 USB Configuration Options summary: (default setting) Legacy USB Support Enabled Disabled Auto Enables BIOS Support for Legacy USB Support. When enabled, USB can be functional in legacy environment like DOS. AUTO option disables legacy support if no USB devices are connected. DISABLE option will keep USB devices available only for EFI application USB3.
Compact Board PCM-QM77 Enables BIOS Support for USB3.0 (XHCI). When disabled, PCH USB3.0 controller will also be disabled. Device Name Auto (Emulation Type) Floppy Forced FDD Hard Disk CD-ROM If Auto. USB devices less than 530MB will be emulated as Floppy and remaining as Floppy and remaining as hard drive. Forced FDD option can be used to force a HDD formatted drive to boot as FDD(Ex.
Compact Board F81216 Second Super IO Configuration Options summary: (default setting) Serial Port 7/8/9/10 Configuration Set Parameters of Serial Port 7/8/9/10 Chapter 3 AMI BIOS Setup 3-18 PCM-QM77
Compact Board PCM-QM77 F81866 Super IO Configutation Options summary: (default setting) Serial Port 1/2/3/4/5/6 Configuration Set Parameters of Serial Port 1/2/3/4/5/6 Parallel Port Configuration Set Parameters of Parallel Port. ERP MODE Disabled ERP Configure ERP Power Control.
Compact Board PCM-QM77 Serial Port X Configuration Options summary: (default setting) Serial Port Disabled Enabled En/Disable specified serial port.
Compact Board PCM-QM77 Select a resource setting for Super IO device. Device Type RS232 RS422 RS485 Configure COM2/6 operated as RS232, RS422 or RS485. Parallel Port Configuration Options summary: (default setting) Parallel Port Disabled Enabled En/Disable parallel port.
Compact Board Change Settings PCM-QM77 Auto IO=378h; IRQ=7; IO=378h; IRQ=5,7,10,11,12; IO=278h; IRQ=5,7,10,11,12; IO=3BCh; IRQ=5,7,10,11,12; Select a resource setting for Super IO device. Device Mode STD Printer Mode SPP Mode EPP-1.9 and SPP Mode EPP-1.7 and SPP Mode ECP Mode ECP and EPP 1.9 Mode ECP and EPP 1.
Compact Board PCM-QM77 F81866 H/W Monitor Options summary: (default setting) Smart Fan Function Disabled Enabled Enable or Disable Smart Fan Smart Fan Mode configuration Smart Fan Mode select Chapter 3 AMI BIOS Setup 3-23
Compact Board PCM-QM77 Smart Fan Mode configuration Options summary: (default setting) Fan 1/2 Smart Fan Control Manual Duty Mode Auto Duty-Cycle Mode Manual Duty Mode: Manually controlling the fan with a given control PWM. Auto Duty-Cycle Mode: Automatically controlling the fan with given parameters. Manual Duty Mode 1 to 100, default is 80/90 Fan Speed value between 1 to 100 Temperature 1/2/3/4 1 to 100, default is 60/50/40/30 Auto fan speed control.
Compact Board Duty Cycle 0/1/2/3/4 PCM-QM77 1 to 100, default is 100/85/70/60/50 Auto fan speed control.
Compact Board Setup submenu: Chipset Options summary: (default setting) PCH-IO Configuration South Bridge Parameters System Agent (SA) Configuration SA Parameters Chapter 3 AMI BIOS Setup 3-26 PCM-QM77
Compact Board PCM-QM77 PCH-IO Configuration Options summary: (default setting) Power Mode ATX Type AT Type Enable or disable ‘It is now safe to turn off your computer.
Compact Board 82583V LAN Controller PCM-QM77 Enabled Disabled En/Disabled Intel 82583V NIC PCH LAN Controller Enabled Disabled En/Disabled onboard NIC Wake on LAN Enabled Disabled En/Disabled integrated LAN to wake the system. (The Wake on LAN cannot be disabled if ME is on at Sx state.
Compact Board PCM-QM77 System Agent (SA) Configuration Options summary: (default setting) VT-d Disabled Enabled Check to enable VT-d function on MCH Graphics Configuration Config Graphics Settings Chapter 3 AMI BIOS Setup 3-29
Compact Board Graphics Configuration Options summary: (default setting) Primary Display Auto IGFX PEG PCI Select graphic adapters to boot Internal Graphics Auto Disabled Enabled En/Disabled internal graphics device Chapter 3 AMI BIOS Setup 3-30 PCM-QM77
Compact Board DVMT Pre-Allocated PCM-QM77 64MB 32MB~1024MB Select DVMT 5.0 Pre-Allocated (Fixed) Graphics Memory size used by the Internal Graphics Device. DVMT Total Gfx Mem 128MB 256MB Max Select DVMT 5.0 Total Graphic Memory size used by the Internal Graphics Device.
Compact Board LCD Control Options summary: (default setting) Primary IGFX Boot Display VBIOS CRT DVI LVDS LVDS2 CRT+LVDS1 Select Primary IGFX boot display device LVDS1 Control Disabled Enabled Chapter 3 AMI BIOS Setup 3-32 PCM-QM77
Compact Board PCM-QM77 Enable or Disable Internal LVDS LVDS2 Control Disabled Enabled Enable or Disable Onboard CH7511 LVDS1/LVDS2 Panel Type 640x480,18-Bit,60Hz 800x480,18-Bit,60Hz 800x600,18-Bit,60Hz 1024x600,18-Bit,60Hz 1024x768,18-Bit,60Hz 1024x768,24-Bit,60Hz 1280x768,24-Bit,60Hz 1280x1024,48-Bit,60Hz 1366x768,24-Bit,60Hz 1440x900,24Bit,60Hz 1600x1200,48-Bit,60Hz 1920x1080,48-Bit,60Hz 640x480,24-Bit,60Hz 800x600,24-Bit,60Hz 1280x768,18-Bit,60Hz Select panel native resolution.
Compact Board PCM-QM77 Select Backlight control type. Inverted: Brightest for low PWM duty cycle and low voltage. Normal: Brightest for high PWM duty cycle and high voltage.
Compact Board PCM-QM77 Setup submenu: Boot Options summary: (default setting) Quiet Boot Disabled Enabled En/Disable showing boot logo. Launch PXE OpROM Disabled policy Enabled En/Disable PXE boot for LAN Boot Option #X/ XXXX Drive BBS Priorities The order of boot priorities.
Compact Board PCM-QM77 BBS Priorities Options summary: (default setting) Boot Option #x Disabled Device name Sets the system boot order Chapter 3 AMI BIOS Setup 3-36
Compact Board PCM-QM77 Setup submenu: Security Options summary: (default setting) Administrator Password/ Not set User Password Chapter 3 AMI BIOS Setup 3-37
Compact Board PCM-QM77 You can install a Supervisor password, and if you install a supervisor password, you can then install a user password. A user password does not provide access to many of the features in the Setup utility. Install the Password: Press Enter on this item, a dialog box appears which lets you enter a password. You can enter no more than six letters or numbers. Press Enter after you have typed in the password. A second dialog box asks you to retype the password for confirmation.
Compact Board PCM-QM77 Setup submenu: Exit Options summary: (default setting) Save Changes and Exit Exit system setup after saving the changes Discard Changes and Exit Exit system setup without saving any changes Save Changes and Reset Reset the system after saving the changes Discard Changes and Reset Save Changes Save Changes done so far to any of the setup options.
Compact Board PCM-QM77 Discard Changes Discard Changes done so far to any of the setup options Reset system setup without saving any changes Restore Defaults Restore/Load Default values for all the setup options.
Compact Board PCM-QM77 Chapter 4 Driver Installation .
Compact Board PCM-QM77 The PCM-QM77 comes with an AutoRun DVD-ROM that contains all drivers and utilities that can help you to install the driver automatically. Insert the driver DVD, the driver DVD-title will auto start and show the installation guide. If not, please follow the sequence below to install the drivers.
Compact Board 4.1 PCM-QM77 Installation: Insert the PCM-QM77 DVD-ROM into the DVD-ROM drive. And install the drivers from Step 1 to Step 10 in order. Step 1 – Install Chipset Driver 1. Click on the STEP 1-CHIPSET folder and select the OS folder your system is 2. Double click on the infinst_autol.exe file located in each OS folder 3. Follow the instructions that the window shows 4. The system will help you install the driver automatically Step 2 – Install VGA Driver 1.
Compact Board PCM-QM77 Note 2: If the OS is Windows® XP, you have to install the driver of dotNet Framework first. Simply click on dotnetfx35.exe located in dotNet Framwork folder. Step 3 –Install LAN Driver 1. Click on the STEP3-LAN folder and select the OS folder your system is 2. Double click on the .exe file located in each OS folder 3. Follow the instructions that the window shows 4. The system will help you install the driver automatically Step 4 –Install Audio Driver 1.
Compact Board PCM-QM77 Step 6 –Install RAID & AHDI Driver Please refer to the Appendix D RAID & AHDI Settings Step 7 – Install TPM Driver 1. Click on the STEP7-TPM folder and select the OS folder your system is 2. Double click on the Setup.exe file located in each OS folder 3. Follow the instructions that the window shows 4. The system will help you install the driver automatically Step 8 –Install Touch Driver 1. Click on the STEP8-TOUCH folder and select the OS folder your system is 2.
Compact Board PCM-QM77 Step 10 – Install Serial Port Driver (Optional) For Windows® XP: 1. Click on the STEP10-Serial Port Driver (Optional) and select the Windows XP OS version folder (WINXP_32 or WWINXP_64) your system is 2. Double click on patch.bat file 3. Follow the instructions that the window shows 4. The system will help you install the driver automatically For Windows® 7: 1. Create a password for Administrator account.
Compact Board PCM-QM77 2. Change User Account Control Settings to [Never notify] 3. Reboot and Administrator login.
Compact Board PCM-QM77 4. To run patch.bat with [Run as administrator].
Compact Board PCM-QM77 Appendix A Programming the Watchdog Timer Appendix A Programming the Watchdog Timer A-1
Compact Board PCM-QM77 A.1 Programming PCM-QM77 utilizes FINTEK 81866 chipset as its watchdog timer controller. Below are the procedures to complete its configuration and the AAEON initial watchdog timer program is also attached based on which you can develop customized program to fit your application. Configuring Sequence Description After the hardware reset or power-on reset, the FINTEK 81866 enters the normal mode with all logical devices disabled except KBC.
Compact Board PCM-QM77 There are three steps to complete the configuration setup: (1) Enter the MB PnP Mode; (2) Modify the data of configuration registers; (3) Exit the MB PnP Mode. Undesired result may occur if the MB PnP Mode is not exited normally. (1) Enter the MB PnP Mode To enter the MB PnP Mode, four special I/O write operations are to be performed during Wait for Key state.
Compact Board PCM-QM77 Watch Dog Timer 1, 2, 3 Control Register (Index=F5h,F6h,FAh Default=00h) Appendix A Programming the Watchdog Timer A-4
Compact Board PCM-QM77 A.
Compact Board PCM-QM77 Void aaeonWdtSetTimeoutCount(BYTE tTimeout){ f81866SetLdn(0x07); f81866WriteByte(F81866_WDT_TIME_REG, tTimeout); } Void aaeonWdtSetEnable(BOOL bEnable){ f81866SetLdn(0x07); if(bEnable){ f81866WriteByte(0x30, 0x01); WDT_BASE_ADDR = (f81866ReadByte(F81866_WDT_BASEADDR_REG_MSB) << 8) | f81866ReadByte(F81866_WDT_BASEADDR_REG_LSB); WDT_STATUS = f81866ReadByte(F81866_WDT_CONTROL_REG); f81866WriteByte(F81866_WDT_CONTROL_REG, WDT_STATUS | 0x20); WDT_STATUS = f81866ReadByte(F81866_WDT_PME_R
Compact Board PCM-QM77 Void aaeonSuperIOClose(){ aaeonioWritePortByte(F81866_INDEX, 0xaa); } Appendix A Programming the Watchdog Timer A-7
Compact Board PCM-QM77 Appendix B I/O Information Appendix B I/O Information B-1
Compact Board B.
Compact Board PCM-QM77 B.
Compact Board B.
Compact Board PCM-QM77 B.
Compact Board PCM-QM77 Appendix C Mating Connector Appendix C Mating Connector C - 1
Compact Board PCM-QM77 C.1 List of Mating Connectors and Cables The table notes mating connectors and available cables.
Compact Board COM Port 2 CN15 PCM-QM77 52A-90-10GB0 Serial PINREX Connector COM Port 1 CN16 1701100206 0 Port 52A-90-10GB0 Serial PINREX Connector LVDS#2 CN18 1701100206 0 Port 0110-01-553-30 E-call Connector COM Port 4 CN19 N/A 52A-90-10GB0 Serial PINREX Connector 1701100206 0 COM Port 3 CN20 Port 52A-90-10GB0 Serial PINREX Connector 1701100206 0 LVDS#1 CN21 N/A 0 Port 0110-01-553-30 E-call Connector N/A N/A 0 AAEON 710-73-12TW0 CN22 LPC Port PINREX LPC 1703120130 1 Cable
Compact Board Connector 0 COM Port 9 CN32 PCM-QM77 Port 52A-90-10GB0 Serial PINREX Connector 1701100206 0 Port USB 3.0 Port 52X-40-20GV5 USB 3.0 CN34 #1, #2 PINREX 1700190450 2 Cable Connector USB 3.0 Port 52X-40-20GV5 USB 3.
Compact Board PCM-QM77 2 Pins For +5Vout CN43 721-81-02TW0 PINREX Connector HDD 1702150155 0 Power Parallel LPT CN44 52A-90-26GB0 PINREX Connector Port 1701260200 0 Cable System Fan CN45 CATCH 1190-700-03S N/A N/A N/A N/A N/A N/A N/A N/A N/A N/A Connector DIO #1 CN46 52A-90-10GB0 PINREX Connector 0 DIO #2 CN47 52A-90-10GB0 PINREX Connector 0 Touch Screen CN48 710-73-09TW0 PINREX Connector 1 CPU Fan CN49 CATCH 1190-700-042 Connector Appendix C Mating Connector C - 5
Compact Board PCM-QM77 Appendix D RAID & AHCI Settings Appendix D RAID & AHCI Settings D-1
Compact Board PCM-QM77 D.1 Setting RAID OS installation to SETUP RAID Mode Step 1: Extract the f6fly-x86.zip from “Driver CD -> Step7-RAID&AHCI\WinXP_32” and copy below files to diskette. Step 2: Connect the USB Floppy drive to the board and insert the diskette from previous step.
Compact Board PCM-QM77 Step 4: Configure DVD/CD-ROM drive as the first boot device.
Compact Board PCM-QM77 Step 6: Press CTRL-I to enter RAID Configuration Utility Step 7: Choose “1.
Compact Board PCM-QM77 Step 8 – Configure RAID parameters for the system Step 9 – Choose “Create Volume” and confirmed in next warning message.
Compact Board PCM-QM77 Step 10 – Exit RAID Configuration Utility and Reboot to DVD/CD-ROM device to install OS Step 11 – Press “F6” to install RAID driver Appendix D RAID & AHCI Settings D-6
Compact Board PCM-QM77 Step 12 – Press “S” to install RAID driver Step 13 – Choose “Intel(R) Mobile Express Chipset SATA RAID Controller” Appendix D RAID & AHCI Settings D-7
Compact Board PCM-QM77 Step 14 – It will show the model you selected and then press ”ENTER”. Windows Setup will continue to install OS. D.2 Setting AHCI OS installation to SETUP AHCI Mode Step 1: Extract the f6fly-x86.zip from “Driver CD -> Step7 RAID&AHCI\WinXP_32” and copy below files to diskette. Step 2: Connect the USB Floppy drive to the board and insert the diskette from previous step.
Compact Board PCM-QM77 Step 3: Configure SATA Controller to RAID mode in BIOS SETUP Menu: Advanced -> SATA Configuration -> SATA Mode -> AHCI Mode Step 4: Configure DVD/CD-ROM drive as the first boot device.
Compact Board PCM-QM77 Step 5: Save changes and exit BIOS SETUP Step 6 – Boot to DVD/CD-ROM device to install OS Step 7 – Press “F6” to install AHCI driver Appendix D RAID & AHCI Settings D-10
Compact Board PCM-QM77 Step 8 – Press “S” to install AHCI driver Step 9 – Choose “Intel(R) 7 Series Chipset Family SATA AHCI Controller” Appendix D RAID & AHCI Settings D-11
Compact Board PCM-QM77 Step 10 – It will show the model you selected and then press ”ENTER”. Windows Setup will continue to install OS.
Compact Board PCM-QM77 Appendix E Electrical Specifications for I/O Ports Appendix E Electrical Specifications for I/O Ports E-1
Compact Board PCM-QM77 E.1 Electrical Specifications for I/O Ports I/O Reference Signal Name Rate Output DVI Ports CN1 +5V +5V/0.5A CN8 BKL_PWR LVDS Port 2 Inverter / +5V/2A or Backlight +12V/2A Connector LVDS Port 1 Inverter / +5V/2A or CN9 BKL_PWR Backlight +12V/2A Connector +5V/1A VGA Ports CN11/CN12 +5V (reserved) mSATA CN13 +3.3V COM Port 2 CN15 +5V/+12V +3.3V/1A +5V/0.5A or +12V/0.5A +3.3V/1A or LVDS Port 2 CN18 LCD_PWR +5V/1A +3.
Compact Board PCI PCM-QM77 +3.3V +3.3V/7.6A +5V +5V/5A +12V +12V/0.5A -12V -12V/0.1A +3.3V +3.3V/3A +12V +12V/5.5A +3.3VSB +3.3V/0.375A CN25 PCI-Express［ CN28 x16］ USB Ports 1 and +5V/1A (per CN34 +5VSB 2 channel) USB Ports 3 and CN35 +5VSB CN36 +5VSB 4 USB 2.0 Ports 5 +5V/0.5A (per and 6 channel) USB 2.0 Ports 7 CN37 +5VSB CN38 +5VSB +5V/1A CN39 +5V +5V/0.5A CN43 +5V +5V/1A System FAN CN45 FAN_POWER +12V/0.
Compact Board PCM-QM77 +5V/1A +5V/(Open DIO0~DIO7 Digital IO Port2 CN47 drain) +5V +5V/1A CPU FAN CN49 Mini-Card Slot CN51 CFast Slot CN52 FAN_POWER +12V/0.5A +3.3VSB +3.3V/1.1A +1.5V +1.5V/0.375A +3.3V +3.3V/0.
Compact Board PCM-QM77 Appendix F Digital I/O Appendix E Digital I/O F-1
Compact Board PCM-QM77 F.1 Digital I/O The F75111 provides one serial access interface, I2C Bus, to read/write internal registers. The address of Serial Bus is 0x6E (0110_1110) The related register for configuring DIO is list as follows: Configuration and Control Register-Index 01h Power-on default [7:0]=0000_1000b Bit Name R/W PWR Description 7 INIT R/W VSB3V Software reset for all registers including Test Mode registers. Users use only.
Compact Board PCM-QM77 GPIO2x Output Control Register-Index 20h Power-on default [7:0]=0000_0000b Bit Name R/W PWR 7 GP27_OCT RL R/W VSB3V 6 GP26_OCT RL R/W VSB3V 5 GP25_OCT RL R/W VSB3V 4 GP24_OCT RL R/W VSB3V 3 GP23_OCT RL R/W VSB3V 2 GP22_OCT RL R/W VSB3V 1 GP21_OCT RL R/W VSB3V 0 GP20_OCT RL R/W VSB3V Description GPIO 27 output control. Set to 1 for output function. Set to 0 for input function (default). GPIO 26 output control. Set to 1 for output function.
Compact Board 4 3 2 1 0 GP24_ODA TA GP23_ODA TA GP22_ODA TA GP21_ODA TA GP20_ODA TA PCM-QM77 R/W VSB3V GPIO 24 output data. R/W VSB3V GPIO 23 output data. R/W VSB3V GPIO 22 output data. R/W VSB3V GPIO 21 output data. R/W VSB3V GPIO 20 output data.
Compact Board PCM-QM77 begin: mov cl,01h mov al,80h call CT_I2CWriteByte call Delay5ms mov al,00h mov cl,20h call CT_I2CWriteByte mov cl,22h call CT_I2CReadByte ;Input : CL - register index ; CH - device ID ;Output : AL - Value read Ct_I2CReadByte mov mov mov Proc Near ch,06eh dx, 0f040h + 00h ; Host Control Register al, 0ffh ; Clear previous commands out dx, al Appendix E Digital I/O F-5
Compact Board call PCM-QM77 Delay5ms mov dx, 0f040h + 04h ; Transmit Slave Address Register inc ch ; Set the slave address and mov al, ch ; prepare for a READ command out dx, al mov dx, 0f040h + 03h ; Host Command Register mov al, cl ; offset to read out mov dx, al dx, 0f040h + 05h xor al, al out dx, al ; Clear old data mov dx, 0f040h + 02h ; Host Control Reegister mov al, 48h out call mov in dx, al CT_Chk_SMBus_Ready dx, 0f040h + 05h al, dx ret Appendix E Digital I/O
Compact Board Ct_I2CReadByte PCM-QM77 Endp ;Input : CL - register index ; CH - device ID ; AL - Value to write ;Output: none Ct_I2CWriteByte mov Proc Near ch,06eh xchg ah, al mov mov dx, 0f040h + 00h ; Host Control Register al, 0ffh ; Clear previous commands out call mov dx, al Delay5ms dx, 0f040h + 04h ; Transmit Slave Address Register mov out al, ch dx, al ; Set the slave address and ; prepare for a WRITE command mov dx, 0f040h + 03h ; Host Command Register mov al, cl ; offse
Compact Board out PCM-QM77 dx, al mov dx, 0f040h + 05h mov al, ah out dx, al mov dx, 0f040h + 00h ; Host Control Register mov al, 48h out call ; Start a byte access dx, al CT_Chk_SMBus_Ready ret Ct_I2CWriteByte Endp ; Wait until the busy bit clears, indicating that the SMBUS ; activity has concluded.
Compact Board PCM-QM77 out dx,al ;clear status call Delay5ms test al, 02H jnz short Clear_final and al, NOT 40H ;mask INUSE bit or al,al jz short Clear_final test al,04h jnz short SMBus_Err loop short Chk_I2c_OK ;termination of command ? ;status OK ? ;device error ;SMbus error due to timeout SMBus_Err: stc ret Clear_final: clc ret CT_Chk_SMBus_Ready Endp END begin Appendix E Digital I/O F-9
