PC/104 CPU Module PFM-540I Rev.B PFM-540I Rev.B ® AMD GeodeTM LX 800 Processor AMD® LX 800 + CS5536 Intel® 82551ER/IT for 10/100Mbps 18/24-bit TFT LCD Panel 4 COM, 4USB PFM-540I Manual Rev.B 1st Ed.
PC/104 CPU Module PFM-540I Rev.B Copyright Notice This document is copyrighted, 2009. All rights are reserved. The original manufacturer reserves the right to make improvements to the products described in this manual at any time without notice. No part of this manual may be reproduced, copied, translated, or transmitted in any form or by any means without the prior written permission of the original manufacturer. Information provided in this manual is intended to be accurate and reliable.
PC/104 CPU Module PFM-540I Rev.B Acknowledgments All other products’ name or trademarks are properties of their respective owners. Award is a trademark of Award Software International, Inc. CompactFlash™ is a trademark of the Compact Flash Association. Intel®, Pentium® M, and Celeron® M are trademarks of Intel® Corporation. ® Microsoft Windows is a registered trademark of Microsoft Corp. ® AMD Geode is a registered trademark of Advanced Micro Devices, Inc.
PC/104 CPU Module PFM-540I Rev.B Packing List Before you begin installing your card, please make sure that the following materials have been shipped: 9681540I02 Cable Kit for PFM-540I-B10 (for standard model) 1701160201 VGA cable x 1 1709100201 USB Cable x 1 1700060152 Keyboard & Mouse Cable x 1 1701440350 44-pin IDE Cable x 1 Quick Installation Guide Utility CD PFM-540I Rev.B Note: The PFM-540I Rev.
PC/104 CPU Module PFM-540I Rev.B Contents Chapter 1 General Information 1.1 Introduction................................................................ 1-2 1.2 Features .................................................................... 1-3 1.3 Specifications ............................................................ 1-4 Chapter 2 Quick Installation Guide 2.1 Safety Precautions .................................................... 2-2 2.2 Location of Connectors and Jumpers .......................
PC/104 CPU Module PFM-540I Rev.B 2.18 IDE Connector (CN9) .............................................. 2-14 2.19 COM1 Connector (CN10)........................................ 2-15 2.20 COM3 Connector (CN11)........................................ 2-16 2.21 Power Connector (CN12)........................................ 2-16 2.22 COM 2 Connector (CN13)....................................... 2-16 2.23 Ethernet Connector (CN14) .................................... 2-17 2.24 LCD Connector (CN15) ............
PC/104 CPU Module PFM-540I Rev.B Appendix B I/O Information B.1 I/O Address Map ....................................................B-2 B.2 Memory Address Map............................................B-2 B.3 IRQ Mapping Chart ................................................B-3 B.4 DMA Channel Assignments...................................B-3 Appendix C Mating Connector C.1 List of Mating Connectors and Cables..................
PC/104 CPU Module PFM-540I Rev.
PC/104 CPU Module PFM-540I Rev.B 1.1 Introduction AAEON Technology, a leading company in embedded boards manufacturing with a full range of PC/104 CPU Modules, launches an economic version PC/104 CPU Module-PFM-540I Rev.B. Its compact size and rich functionality ensures the most cost effective and compatible module to coincide with your existing system planning devices. PFM-540I Rev.B adopts an AMD Geode LX 800 processor that is more cost effective compared to other PC/104 CPU modules on the market.
PC/104 CPU Module PFM-540I Rev.B 1.2 Features AMD Geode LX 800 (500MHz) Processor Onboard DDR SDRAM, Max. 1GB for DDR333 and 512MB for DDR400 18/24-bit TFT LCD panel CFD Type I, ATA-33 4 USB 2.
PC/104 CPU Module PFM-540I Rev.B 1.3 Specifications System Processor AMD Geode LX 800 (500MHz) Processor System Memory 200-pin Onboard DDR SDRAM SODIMM x 1, Max. 1GB for DDR333 and 512MB for DDR 400 (Please refer to the Quick Installation Guide 2.
PC/104 CPU Module PFM-540I Rev.
PC/104 CPU Module PFM-540I Rev.B Chapter 2 Quick Installation Guide Notice: The Quick Installation Guide is derived from Chapter 2 of user manual. For other chapters and further installation instructions, please refer to the user manual CD-ROM that came with the product. Part No.
PC/104 CPU Module PFM-540I Rev.B 2.1 Safety Precautions Always completely disconnect the power cord from your board whenever you are working on it. Do not make connections while the power is on, because a sudden rush of power can damage sensitive electronic components. Always ground yourself to remove any static charge before touching the board. Modern electronic devices are very sensitive to static electric charges. Use a grounding wrist strap at all times.
PC/104 CPU Module PFM-540I Rev.B 2.
PC/104 CPU Module Solder Side Chapter 2 Quick Installation Guide 2 - 4 PFM-540I Rev.
PC/104 CPU Module PFM-540I Rev.B 2.
PC/104 CPU Module Solder Side Chapter 2 Quick Installation Guide 2 - 6 PFM-540I Rev.
PC/104 CPU Module PFM-540I Rev.B 2.4 List of Jumpers The board has a number of jumpers that allow you to configure your system to suit your application.
PC/104 CPU Module PFM-540I Rev.B 2.5 List of Connectors The board has a number of connectors that allow you to configure your system to suit your application. The table below shows the function of each board's connectors: Note: For further information about mating connectors, please refer to the appendix of manual.
PC/104 CPU Module PFM-540I Rev.B BAT1 Battery Connector CFD1 Type1 Compact Flash Slot SODIMM1 DDR1 SODIMM Slot 2.6 Setting Jumpers You configure your card to match the needs of your application by setting jumpers. A jumper is the simplest kind of electric switch. It consists of two metal pins and a small metal clip (often protected by a plastic cover) that slides over the pins to connect them. To “close” a jumper you connect the pins with the clip. To “open” a jumper you remove the clip.
PC/104 CPU Module PFM-540I Rev.B 2.7 CFD Master/Slave Selection (JP1) JP1 Function 1-2 Slave 2-3 Master (Default) 2.8 RS-232 Ring/5V Selection (JP2) JP2 Function COM1 1-3 +5V 3-5 Ring (Default) COM2 2-4 +5V 4-6 Ring (Default) 2.
PC/104 CPU Module PFM-540I Rev.B 2.10 Front Panel Connector (CN1) Pin Signal 1 Power LED(+) 2 Power LED(-) 3 N.C 4 Speaker(+) 5 Speaker(-) 6 N.C 7 IDE LED(+) 8 IDE LED(-) 9 N.C 10 Reset(+) 11 Reset(-) 12 N.C 13 Lan Speed LED(+) 14 Lan Speed LED(-) 15 Lan Active LED(+) 16 Lan Active LED(-) 17 N.C 18 N.C 19 N.C 20 N.C 21 N.
PC/104 CPU Module 22 PFM-540I Rev.B N.C 2.11 PS2 Keyboard/Mouse Connector (CN2) Pin Signal Pin Signal 1 KB_DATA 2 KB_CLK 3 GND 4 +5V 5 MS_DATA 6 MS_CLK 2.12 Optional Power Connector (CN3) Pin Signal 1 -12V 2 -5V 3 GND 2.
PC/104 CPU Module PFM-540I Rev.B 2.14 VGA Display Connector (CN5) Pin Signal Pin Signal 1 RED 2 +5V 3 GREEN 4 GND 5 BLUE 6 N.C 7 N.C 8 DDCDAT 9 GND 10 HSYNC 11 GND 12 VSYNC 13 GND 14 DDCCLK 15 GND 16 GND 2.15 USB (1-2) Connector (CN6) Pin Signal Pin Signal 1 +5V 2 GND 3 USBD1- 4 GND 5 USBD1+ 6 USBD2+ 7 GND 8 USBD2- 9 GND 10 +5V 2.16 PC/104 Connector (CN7) As standard.
PC/104 CPU Module PFM-540I Rev.B 2.17 LPT Port Connector (CN8) Pin Signal Pin Signal 1 #STROBE 2 #AFD 3 DATA0 4 #ERROR 5 DATA1 6 #INIT 7 DATA2 8 #SLIN 9 DATA3 10 GND 11 DATA4 12 GND 13 DATA5 14 GND 15 DATA6 16 GND 17 DATA7 18 GND 19 #ACK 20 GND 21 BUSY 22 GND 23 PE 24 GND 25 SELECT 26 N.C 2.
PC/104 CPU Module PFM-540I Rev.B 13 DATA2 14 DATA13 15 DATA1 16 DATA14 17 DATA0 18 DATA15 19 GND 20 N.C 21 REQ 22 GND 23 #IOW 24 GND 25 #IOR 26 GND 27 IOREADY 28 GND 29 #DACK 30 GND 31 IRQ 32 N.C 33 ADDR1 34 DETECT 35 ADDR0 36 ADDR2 37 #CS0 38 #CS1 39 HDDLED 40 GND 41 +5V 42 +5V 43 GND 44 N.C Note: The IDE interface on PFM-540I only supports two IDE devices. If you use a CF card, there is only one IDE device usable. 2.
PC/104 CPU Module PFM-540I Rev.B 7 RTS 8 CTS 9 RI/5V 10 N.C 2.20 COM3 Connector (CN11) Pin Signal Pin Signal 1 DCD 2 RXD 3 TXD 4 DTR 5 GND 6 DSR 7 RTS 8 CTS 9 RI 10 N.C 2.21 Power Connector (CN12) Pin Signal 1 +5V 2 GND 3 GND 4 +12V 2.
PC/104 CPU Module 9 RI/5V PFM-540I Rev.B 10 N.C 2.23 Ethernet Connector (CN14) Pin Signal Pin Signal 1 RX- 2 RX+ 3 N.C 4 N.C 5 CHASSIS_GND 6 CHASSIS_GND 7 N.C 8 N.C 9 TX+ 10 TX- 2.24 LCD Connector (CN15) 24-bit TTL Pin Signal Pin Signal 1 +5V 2 +5V 3 GND 4 GND 5 +3.3V 6 +3.
PC/104 CPU Module PFM-540I Rev.B 23 GREEN6 24 GREEN7 25 RED0 26 RED1 27 RED2 28 RED3 29 RED4 30 RED5 31 RED6 32 RED7 33 GND 34 GND 35 CLOCK 36 VSYNC 37 DE 38 HSYNC 39 N.C 40 ENAVEE 18-bit TTL Pin Signal Pin Signal 1 +5V 2 +5V 3 GND 4 GND 5 +3.3V 6 +3.3V 7 ENBKL 8 GND 9 N.C 10 N.C 11 BLUE0 12 BLUE1 13 BLUE2 14 BLUE3 15 BLUE4 16 BLUE5 17 N.C 18 N.
PC/104 CPU Module PFM-540I Rev.B 25 N.C 26 N.C 27 RED0 28 RED1 29 RED2 30 RED3 31 RED4 32 RED5 33 GND 34 GND 35 CLOCK 36 VSYNC 37 DE 38 HSYNC 39 N.C 40 ENAVEE 2.25 COM4 Connector (CN16) Pin Signal Pin Signal 1 DCD 2 RXD 3 TXD 4 DTR 5 GND 6 DSR 7 RTS 8 CTS 9 RI 10 N.C 2.26 Battery Connector (BAT1) Pin Signal Pin Signal 1 +3V 2 GND 2.27 DDR1 SODIMM Slot (SODIMM1 ) Standard SODIMM Slot Note from AMD: Memory configurations supported.
PC/104 CPU Module PFM-540I Rev.B supported as long as the configuration requirements are met. Devices Max Memory1 Max GLIU GLCP 4C00000Fh Frequency Upper Bits/Lower Bits GLMC 2000001 Ah Bits【26:24】 4 512M 400MHz F2F100FFh/ 56960004h 4 8 1G 400MHz F2F100FFh/ 56960004h 4 4 512M 333MHz F2F100FFh/ 56960004h 3 8 1G 333MHz F2F100FFh/ 56960004h 3 16 2G 333MHz F2F100FFh/ 56960004h 3 1: Maximum memory is assuming 1Gbit devices.
PC/104 CPU Module PFM-540I Rev.
PC/104 CPU Module PFM-540I Rev.
PC/104 CPU Module 3.1 PFM-540I Rev.B System Test and Initialization These routines test and initialize board hardware. If the routines encounter an error during the tests, you will either hear a few short beeps or see an error message on the screen. There are two kinds of errors: fatal and non-fatal. The system can usually continue the boot up sequence with non-fatal errors.
PC/104 CPU Module 3.2 PFM-540I Rev.B Award BIOS Setup Awards BIOS ROM has a built-in Setup program that allows users to modify the basic system configuration. This type of information is stored in battery-backed CMOS RAM so that it retains the Setup information when the power is turned off. Entering Setup Power on the computer and press immediately. This will allow you to enter Setup. Standard CMOS Features Use this menu for basic system configuration. (Date, time, IDE, etc.
PC/104 CPU Module PFM-540I Rev.B PC Health Status This menu allows you to set the shutdown temperature for your system. Frequency/Voltage Control Use this menu to specify your settings for auto detect DIMM/PCI clock and spread spectrum. Load Fail-Safe Defaults Use this menu to load the BIOS default values for the minimal/stable performance for your system to operate.
PC/104 CPU Module PFM-540I Rev.
PC/104 CPU Module PFM-540I Rev.B 4.1 Software Drivers This chapter describes the operation and installation of the display drivers supplied on the Supporting CD-ROM that are shipped with your product. The onboard VGA adapter is based on the AMD LX VGA Flat Panel/CRT controller. This controller offers a large set of extended functions and higher resolutions. The purpose of the enclosed software drivers is to take advantage of the extended features of the AMD LX VGA Flat Panel/CRT controller.
PC/104 CPU Module PFM-540I Rev.B 4.2 Necessary to Know The instructions in this manual assume that you understand elementary concepts of MS-DOS and the IBM Personal Computer.
PC/104 CPU Module PFM-540I Rev.B 4.3 Installing VGA Driver Win XP / Win XPe VGA Place the Driver CD-ROM into your CD-ROM drive and follow the steps below to install. 1. Click on Start button. 2. Click on Settings button. 3. Click on Control Panel button. 4. Click on System button. 5. Select Hardware and click on Device Manager…. 6. Double click on Video Controller (VGA Compatible). 7. Click on Update Driver…. 8. Click on Next. 9. Select Search for a suitable driver…, then click on Next. 10.
PC/104 CPU Module PFM-540I Rev.B 4.4 Installing AES Driver Win XP / Win XPe Geode LX AES Crypto Place the Driver CD-ROM into your CD-ROM drive and follow the steps below to install. 1. Click on Start button. 2. Click on Settings button. 3. Click on Control Panel button. 4. Click on System button. 5. Select Hardware and click on Device Manager…. 6. Double click on Entertainment Encryption/Decryption Controller. 7. Click on Update Driver…. 8. Click on Next. 9.
PC/104 CPU Module PFM-540I Rev.B 4.5 Installing PCI to ISA Bridge Driver Win XP / Win XPe System Place the Driver CD-ROM into your CD-ROM drive and follow the steps below to install. 1. Click on Start button. 2. Click on Settings button. 3. Click on Control Panel button. 4. Click on System button. 5. Select Hardware and click on Device Manager…. 6. Double click on Other PCI Bridge Device 7. Click on Update Driver…. 8. Click on Next. 9. Select Search for a suitable driver…, then click on Next. 10.
PC/104 CPU Module PFM-540I Rev.B 4.6 Installing Ethernet Driver Place the Driver CD-ROM into your CD-ROM drive and follow the steps below to install. 1. Click on Start button. 2. Click on Settings button. 3. Click on Control Panel button. 4. Click on System button. 5. Select Hardware and click on Device Manager…. 6. Double click on Ethernet Controller. 7. Click on Update Driver…. 8. Click on Next. 9. Select Search for a suitable driver…, then click on Next. 10.
PC/104 CPU Module PFM-540I Rev.
PC/104 CPU Module PFM-540I Rev.B A.1 Programming PFM-540I Rev.B utilizes SCH3114-NU chipset as its watchdog timer controller. The SCH311X WDT ( Watch Dog Timer ) has a programmable time-out ranging from 1 to 255 minutes with one minute resolution, or 1 to 255 second resolution. The unit of the WDT timeout value are selected via bit[7] of the WDT_TIMEOUT register. The WDT time-out value is set through the WDT_VAL Runtime register.
PC/104 CPU Module PFM-540I Rev.
PC/104 CPU Module PFM-540I Rev.B The following is a sample code to set WDT for 3 seconds. ;Runtime register I/O base address SUPERIO_GPIO_PORT .MODEL EQU 800h SMALL .
PC/104 CPU Module PFM-540I Rev.
PC/104 CPU Module B.1 I/O Address Map B.2 1st MB Memory Address Map Appendix B I/O Information B-2 PFM-540I Rev.
PC/104 CPU Module PFM-540I Rev.B B.3 IRQ Mapping Chart B.
PC/104 CPU Module PFM-540I Rev.
PC/104 CPU Module PFM-540I Rev.B C.1 List of Mating Connectors and Cables The table notes mating connectors and available cables.
PC/104 CPU Module CN16 BAT1 PFM-540I Rev.B COM4 Keentop 1014 Serial Port Cable Connector Series Battery HRS DF14-MS-1 Connector .
