PC 104 CPU Module PFM-540I PFM-540I AMD® Geode LX 800 Processor AMD LX 800 +CS 5536 RTL8139DL for 10/100Mbps 18/24-bit TFT LCD Panel 2 COM, 4 USB, 1 IrDA PFM-540I Manual Rev.A 1st Ed. NOV.
PC 104 CPU Module PFM-540I Copyright Notice This document is copyrighted, 2006. All rights are reserved. The original manufacturer reserves the right to make improvements to the products described in this manual at any time without notice. No part of this manual may be reproduced, copied, translated, or transmitted in any form or by any means without the prior written permission of the original manufacturer. Information provided in this manual is intended to be accurate and reliable.
PC 104 CPU Module PFM-540I Acknowledgments All other products’ name or trademarks are properties of their respective owners. Award is a trademark of Award Software International, Inc. CompactFlash™ is a trademark of the Compact Flash Association. Intel®, Pentium® M, and Celeron® M are trademarks of Intel® Corporation. ® Microsoft Windows is a registered trademark of Microsoft Corp. ® AMD Geode is a registered trademark of Advanced Micro Devices, Inc.
PC 104 CPU Module PFM-540I Packing List Before you begin installing your card, please make sure that the following materials have been shipped: 9681540I00 Cable Kit for PFM-540I 1701160201 VGA cable x 1 1701260201 Printer Port Cable x 1 1709100201 USB Cable x 1 1700100200 LAN Cable x 1 1700060152 Keyboard & Mouse Cable x 1 1701440350 44-pin IDE Cable x 1 1701100207 RS-232 Cable x 2 1701340703 Floppy Disk Cable x 1 9657666600 Jumper Cap Quick Installation Guide Utility CD PFM-540I If any of
PC 104 CPU Module PFM-540I Contents Chapter 1 General Information 1.1 Introduction................................................................ 1-2 1.2 Features .................................................................... 1-3 1.3 Specifications ............................................................ 1-4 Chapter 2 Quick Installation Guide 2.1 Safety Precautions .................................................... 2-2 2.2 Location of Connectors and Jumpers ....................... 2-3 2.
PC 104 CPU Module PFM-540I 2.18 IDE Connector (CN9) .............................................. 2-14 2.19 COM1 Connector (CN10)........................................ 2-15 2.20 Floppy Connector (CN11) ....................................... 2-16 2.21 Power Connector (CN12)........................................ 2-17 2.22 COM 2 Connector (CN13)....................................... 2-17 2.23 Ethernet Connector (CN14) .................................... 2-17 2.24 LCD Connector (CN15) ................
PC 104 CPU Module PFM-540I Appendix B I/O Information B.1 I/O Address Map ....................................................B-2 B.2 Memory Address Map............................................B-3 B.3 IRQ Mapping Chart ................................................B-4 B.4 DMA Channel Assignments...................................B-4 Appendix C Mating Connector C.1 List of Mating Connectors and Cables..................
PC 104 CPU Module PFM-540I Chapter 1 General Information Chapter 1 General Information 1- 1
PC 104 CPU Module PFM-540I 1.1 Introduction AAEON Technology, a leading company in embedded boards manufacturing with a full range of PC/104 CPU Modules, launches an economic version PC/104 CPU Module-PFM-540I. Its compact size and rich functionality ensures the most cost effective and compatible module to coincide with your existing system planning devices. PFM-540I adopts an AMD Geode LX800 processor that is more cost effective compared to other PC/104 CPU modules on the market.
PC 104 CPU Module PFM-540I 1.2 Features AMD Geode LX800 (500MHz) Processor Supports Onboard DDR SDRAM, Max. 1GB for DDR333 and 512MB for DDR400 Supports 18/24-bit TFT LCD panel Supports CFD Type I, ATA-33 Supports 4 USB 2.
PC 104 CPU Module PFM-540I 1.3 Specifications System Processor AMD Geode LX 800 (500MHz) Processor System Memory 200-pin Onboard DDR SDRAM SODIMM x 1, Max. 1GB for DDR333 and 512MB for DDR 400 (Please refer to the Quick Installation Guide 2.
PC 104 CPU Module PFM-540I Display Chipset AMD LX 800 Memory Shared system memory up to 254 MB Resolution Up to 1920 x 1440 @ 32bpp for CRT Up to 1024 x 768 @ 24bpp for LCD LCD Interface Up to 18/24-bit TTL TFT LCD MIO EIDE x 1 (UDMA-33 x 1); Floppy Disk I/O Drive x 1; Keyboard & Mouse x 1; RS-232 x 1; RS-232/422/485 x 1; Parallel x 1 IDE Interface ATA-33 x 1 channel, 44-pin header USB Four USB 2.
PC 104 CPU Module PFM-540I Chapter 2 Quick Installation Guide Notice: The Quick Installation Guide is derived from Chapter 2 of user manual. For other chapters and further installation instructions, please refer to the user manual CD-ROM that came with the product. Part No. 2007540I10 Printed in Taiwan, Nov.
PC 104 CPU Module PFM-540I 2.1 Safety Precautions Always completely disconnect the power cord from your board whenever you are working on it. Do not make connections while the power is on, because a sudden rush of power can damage sensitive electronic components. Always ground yourself to remove any static charge before touching the board. Modern electronic devices are very sensitive to static electric charges. Use a grounding wrist strap at all times.
PC 104 CPU Module PFM-540I 2.
PC 104 CPU Module Solder Side Chapter 2 Quick Installation Guide 2 - 4 PFM-540I
PC 104 CPU Module PFM-540I 2.
PC 104 CPU Module Solder Side Chapter 2 Quick Installation Guide 2 - 6 PFM-540I
PC 104 CPU Module PFM-540I 2.4 List of Jumpers The board has a number of jumpers that allow you to configure your system to suit your application.
PC 104 CPU Module PFM-540I 2.5 List of Connectors The board has a number of connectors that allow you to configure your system to suit your application. The table below shows the function of each board's connectors: Note: For further information about mating connectors, please refer to the appendix of manual.
PC 104 CPU Module PFM-540I CFD1 Type1 Compact Flash Slot SODIMM1 DDR1 SODIMM Slot 2.6 Setting Jumpers You configure your card to match the needs of your application by setting jumpers. A jumper is the simplest kind of electric switch. It consists of two metal pins and a small metal clip (often protected by a plastic cover) that slides over the pins to connect them. To “close” a jumper you connect the pins with the clip. To “open” a jumper you remove the clip.
PC 104 CPU Module PFM-540I 2.7 CFD Master/Slave Selection (JP1) JP1 Function 1-2 Slave 2-3 Master (Default) 2.8 RS-232 Ring/5V Selection (JP2) JP2 Function COM1 1-3 +5V 3-5 Ring (Default) COM2 2-4 +5V 4-6 Ring (Default) 2.
PC 104 CPU Module 4-6 PFM-540I Clear 2.10 Front Panel Connector (CN1) Pin Signal Pin Signal 1 Power LED (+) 2 Power LED (-) 3 N.C. 4 Speaker (+) 5 Speaker(-) 6 N.C. 7 IDE LED(+) 8 IDE LED(-) 9 N.C. 10 Reset(+) 11 Reset(-) 12 N.C. 13 Lan Speed LED(+) 14 Lan Speed LED(-) 15 Lan Active LED(+) 16 Lan Active LED(-) 17 N.C. 18 IrDA(+5V) 19 IrDA(N.C.) 20 IrDA(RX) 21 IrDA(GND) 22 IrDA(TX) 2.
PC 104 CPU Module PFM-540I 2.12 Option Power Connector (CN3) Pin Signal 1 -12V 2 -5V 3 GND 2.13 USB 3-4 Connector (CN4) Pin Signal Pin Signal 1 +5V 2 GND 3 USBD3- 4 GND 5 USBD3+ 6 USBD4+ 7 GND 8 USBD4- 9 GND 10 +5V 2.14 VGA Display Connector (CN5) Pin Signal Pin Signal 1 RED 2 +5V 3 GREEN 4 GND 5 BLUE 6 N.C. 7 N.C.
PC 104 CPU Module PFM-540I 11 GND 12 VSYNC 13 GND 14 DDCCLK 15 GND 16 GND 2.15 USB 1-2 Connector (CN6) Pin Signal Pin Signal 1 +5V 2 GND 3 USBD1- 4 GND 5 USBD1+ 6 USBD2+ 7 GND 8 USBD2- 9 GND 10 +5V 2.16 PC 104 Connector (CN7) As standard. Note: PFM-540I does not support ISA card with DMA or Master mode in PC/104 interface. 2.
PC 104 CPU Module PFM-540I 5 DATA1 6 #INIT 7 DATA2 8 #SLIN 9 DATA3 10 GND 11 DATA4 12 GND 13 DATA5 14 GND 15 DATA6 16 GND 17 DATA7 18 GND 19 #ACK 20 GND 21 BUSY 22 GND 23 PE 24 GND 25 SELECT 26 N.C. 2.
PC 104 CPU Module PFM-540I 19 GND 20 N.C. 21 REQ 22 GND 23 #IOW 24 GND 25 #IOR 26 GND 27 IOREADY 28 GND 29 #DACK 30 GND 31 IRQ 32 N.C. 33 ADDR1 34 DETECT 35 ADDR0 36 ADDR2 37 #CS0 38 #CS1 39 HDDLED 40 GND 41 +5V 42 +5V 43 GND 44 N.C. Note: The IDE interface on PFM-540I only supports two IDE devices. If you use a CF card, there is only one IDE device usable. 2.
PC 104 CPU Module PFM-540I 2.20 Floppy Connector (CN11) Pin Signal Pin Signal 1 GND 2 #DENSEL 3 GND 4 N.C. 5 GND 6 N.C. 7 GND 8 #INDEX 9 GND 10 #MOTOR A 11 GND 12 #DRIVE SELECT B 13 GND 14 #DRIVE SELECT A 15 GND 16 #MOTOR B 17 GND 18 #DIR 19 GND 20 #STEP 21 GND 22 #WRITE DATA 23 GND 24 #WRITE GATE 25 GND 26 #TRACK0 27 GND 28 #WRITE PROTECT 29 N.C. 30 #READ DATA 31 GND 32 #HDSEL 33 N.C.
PC 104 CPU Module PFM-540I 2.21 Power Connector (CN12) Pin Signal Pin Signal 1 +5V 2 GND 3 GND 4 +12V 2.22 COM 2 Connector (CN13) Pin Signal Pin Signal 1 DCD(485/422_TX-) 2 RXD(422_RX+) 3 TXD(485/422_TX+) 4 DTR(422_RX-) 5 GND 6 DSR 7 RTS 8 CTS 9 RI/5V 10 N.C. 2.23 Ethernet Connector (CN14) Pin Signal Pin Signal 1 RX- 2 RX+ 3 N.C. 4 N.C. 5 CHASSIS_GND 6 CHASSIS_GND 7 N.C. 8 N.C.
PC 104 CPU Module PFM-540I 2.24 LCD Connector (CN15) 24-bit TTL Pin Signal Pin Signal 1 +5V 2 +5V 3 GND 4 GND 5 +3.3V 6 +3.3V 7 ENBKL 8 GND 9 BLUE0 10 BLUE1 11 BLUE2 12 BLUE3 13 BLUE4 14 BLUE5 15 BLUE6 16 BLUE7 17 GREEN0 18 GREEN1 19 GREEN2 20 GREEN3 21 GREEN4 22 GREEN5 23 GREEN6 24 GREEN7 25 RED0 26 RED1 27 RED2 28 RED3 29 RED4 30 RED5 31 RED6 32 RED7 33 GND 34 GND 35 CLOCK 36 VSYNC 37 DE 38 HSYNC 39 N.C.
PC 104 CPU Module PFM-540I 18-bit TTL Pin Signal Pin Signal 1 +5V 2 +5V 3 GND 4 GND 5 +3.3V 6 +3.3V 7 ENBKL 8 GND 9 N.C 10 N.C 11 BLUE0 12 BLUE1 13 BLUE2 14 BLUE3 15 BLUE4 16 BLUE5 17 N.C 18 N.C 19 GREEN0 20 GREEN1 21 GREEN2 22 GREEN3 23 GREEN4 24 GREEN5 25 N.C 26 N.C 27 RED0 28 RED1 29 RED2 30 RED3 31 RED4 32 RED5 33 GND 34 GND 35 CLOCK 36 VSYNC 37 DE 38 HSYNC 39 N.
PC 104 CPU Module PFM-540I 2.25 Battery Connector (BAT1) Pin Signal Pin Signal 1 +3V 2 GND 2.26 DDR1 SODIMM Slot (SODIMM1 ) Standard SODIMM Slot Note from AMD: Memory configurations supported. Only one DIMM or SODIMM is supported as long as the configuration requirements are met.
PC 104 CPU Module PFM-540I Chapter 3 Award BIOS Setup Chapter 3 Award BIOS Setup 3-1
PC 104 CPU Module 3.1 PFM-540I System Test and Initialization These routines test and initialize board hardware. If the routines encounter an error during the tests, you will either hear a few short beeps or see an error message on the screen. There are two kinds of errors: fatal and non-fatal. The system can usually continue the boot up sequence with non-fatal errors.
PC 104 CPU Module 3.2 PFM-540I Award BIOS Setup Awards BIOS ROM has a built-in Setup program that allows users to modify the basic system configuration. This type of information is stored in battery-backed CMOS RAM so that it retains the Setup information when the power is turned off. Entering Setup Power on the computer and press immediately. This will allow you to enter Setup. Standard CMOS Features Use this menu for basic system configuration. (Date, time, IDE, etc.
PC 104 CPU Module PFM-540I Advanced Chipset Features Use this menu to change the values in the chipset registers and optimize your system performance. Integrated Peripherals Use this menu to specify your settings for integrated peripherals. (Primary slave, secondary slave, keyboard, mouse etc.) Power Management Setup Use this menu to specify your settings for power management. (HDD power down, power on by ring, KB wake up, etc.) PnP/PCI Configurations This entry appears if your system supports PnP/PCI.
PC 104 CPU Module PFM-540I Load Optimized Defaults Use this menu to load the BIOS default values that are factory settings for optimal performance system operations. While AWARD has designated the custom BIOS to maximize performance, the factory has the right to change these defaults to meet their needs. Set Supervisor/User Password Use this menu to set Supervisor/User Passwords. Save and Exit Setup Save CMOS value changes to CMOS and exit setup.
PC 104 CPU Module PFM-540I Chapter 4 Driver Installation Chapter 4 Driver Installation 4 - 1
PC 104 CPU Module PFM-540I 4.1 Software Drivers This chapter describes the operation and installation of the display drivers supplied on the Supporting CD-ROM that are shipped with your product. The onboard VGA adapter is based on the AMD LX VGA Flat Panel/CRT controller. This controller offers a large set of extended functions and higher resolutions. The purpose of the enclosed software drivers is to take advantage of the extended features of the AMD LX VGA Flat Panel/CRT controller.
PC 104 CPU Module PFM-540I 4.2 Necessary to Know The instructions in this manual assume that you understand elementary concepts of MS-DOS and the IBM Personal Computer.
PC 104 CPU Module PFM-540I 4.3 Installing VGA Driver Win XP / Win XPe VGA Place the Driver CD-ROM into your CD-ROM drive and follow the steps below to install. 1. Click on Start button. 2. Click on Settings button. 3. Click on Control Panel button. 4. Click on System button. 5. Select Hardware and click on Device Manager…. 6. Double click on Video Controller (VGA Compatible). 7. Click on Update Driver…. 8. Click on Next. 9. Select Search for a suitable driver…, then click on Next. 10.
PC 104 CPU Module PFM-540I 4.4 Installing AES Driver Win XP / Win XPe Geode LX AES Crypto Place the Driver CD-ROM into your CD-ROM drive and follow the steps below to install. 1. Click on Start button. 2. Click on Settings button. 3. Click on Control Panel button. 4. Click on System button. 5. Select Hardware and click on Device Manager…. 6. Double click on Entertainment Encryption/Decryption Controller. 7. Click on Update Driver…. 8. Click on Next. 9.
PC 104 CPU Module PFM-540I 4.5 Installing PCI to ISA Bridge Driver Win XP / Win XPe System Place the Driver CD-ROM into your CD-ROM drive and follow the steps below to install. 1. Click on Start button. 2. Click on Settings button. 3. Click on Control Panel button. 4. Click on System button. 5. Select Hardware and click on Device Manager…. 6. Double click on Other PCI Bridge Device 7. Click on Update Driver…. 8. Click on Next. 9. Select Search for a suitable driver…, then click on Next. 10.
PC 104 CPU Module PFM-540I 4.6 Installing Ethernet Driver 1. Click on the Step 4 –Install Lan folder. 2. Double click on the Setup file located in the folder. 3. Follow the instructions that the window shows. 4. The system will help you install the driver automatically. 4.7 Ethernet Software Configuration The onboard Ethernet interface supports all major network operating systems. I/O addresses and interrupts are easily configured via the Insyde BIOS Setup.
PC 104 CPU Module PFM-540I guide displayed at the bottom of the screen for additional information. 4. After you have made your selections and the configuration is what you want, press . A prompt will appear asking if you want to save the configuration. Press "Y" if you want to save. There are three very useful diagnostic functions offered in the Ethernet Setup Menu as follows: 1. Run EEPROM test 2. Run Diagnostics on Board 3.
PC 104 CPU Module PFM-540I Appendix A Programming the Watchdog Timer Appendix A Programming the Watchdog Timer A-1
PC 104 CPU Module PFM-540I A.1 Programming PFM-540I utilizes IT8712F-A chipset as its watchdog timer controller. Below are the procedures to complete its configuration and the AAEON intial watchdog timer program is also attached based on which you can develop customized program to fit your application. Configuring Sequence Description After the hardware reset or power-on reset, the IT8712F-A enters the normal mode with all logical devices disabled except KBC.
PC 104 CPU Module PFM-540I There are three steps to complete the configuration setup: (1) Enter the MB PnP Mode; (2) Modify the data of configuration registers; (3) Exit the MB PnP Mode. Undesired result may occur if the MB PnP Mode is not exited normally. (1) Enter the MB PnP Mode To enter the MB PnP Mode, four special I/O write operations are to be performed during Wait for Key state.
PC 104 CPU Module PFM-540I WatchDog Timer Configuration Registers Configure Control (Index=02h) This register is write only. Its values are not sticky; that is to say, a hardware reset will automatically clear the bits, and does not require the software to clear them.
PC 104 CPU Module PFM-540I WatchDog Timer Configuration Register (Index=72h, Default=00h) WatchDog Timer Time-out Value Register (Index=73h, Default=00h) Appendix A Programming the Watchdog Timer A-5
PC 104 CPU Module PFM-540I A.2 IT8712F-A Watchdog Timer Initial Program .MODEL SMALL .CODE Main: CALL Enter_Configuration_mode CALL Check_Chip mov cl, 7 call Set_Logic_Device ;time setting mov cl, 10 ; 10 Sec dec al Watch_Dog_Setting: ;Timer setting mov al, cl mov cl, 73h call Superio_Set_Reg ;Clear by keyboard or mouse interrupt mov al, 0f0h mov cl, 71h call Superio_Set_Reg ;unit is second.
PC 104 CPU Module PFM-540I ; game port enable mov cl, 9 call Set_Logic_Device Initial_OK: CALL Exit_Configuration_mode MOV AH,4Ch INT 21h Enter_Configuration_Mode PROC NEAR MOV SI,WORD PTR CS:[Offset Cfg_Port] MOV DX,02Eh MOV CX,04h Init_1: MOV AL,BYTE PTR CS:[SI] OUT DX,AL INC SI LOOP Init_1 RET Enter_Configuration_Mode ENDP Exit_Configuration_Mode PROC NEAR MOV AX,0202h CALL Write_Configuration_Data Appendix A Programming the Watchdog Timer A-7
PC 104 CPU Module PFM-540I RET Exit_Configuration_Mode ENDP Check_Chip PROC NEAR MOV AL,20h CALL Read_Configuration_Data CMP AL,87h JNE Not_Initial MOV AL,21h CALL Read_Configuration_Data CMP AL,12h JNE Not_Initial Need_Initial: STC RET Not_Initial: CLC RET Check_Chip ENDP Read_Configuration_Data PROC NEAR MOV DX,WORD PTR CS:[Cfg_Port+04h] OUT DX,AL Appendix A Programming the Watchdog Timer A-8
PC 104 CPU Module PFM-540I MOV DX,WORD PTR CS:[Cfg_Port+06h] IN AL,DX RET Read_Configuration_Data ENDP Write_Configuration_Data PROC NEAR MOV DX,WORD PTR CS:[Cfg_Port+04h] OUT DX,AL XCHG AL,AH MOV DX,WORD PTR CS:[Cfg_Port+06h] OUT DX,AL RET Write_Configuration_Data ENDP Superio_Set_Reg proc near push ax MOV DX,WORD PTR CS:[Cfg_Port+04h] mov al,cl out dx,al pop ax inc dx out dx,al ret Superio_Set_Reg endp.
PC 104 CPU Module PFM-540I push ax push cx xchg al,cl mov cl,07h call Superio_Set_Reg pop cx pop ax ret Set_Logic_Device endp ;Select 02Eh->Index Port, 02Fh->Data Port Cfg_Port DB 087h,001h,055h,055h DW 02Eh,02Fh END Main Note: Interrupt level mapping 0Fh-Dh: not valid 0Ch: IRQ12 . .
PC 104 CPU Module PFM-540I Appendix B I/O Information Appendix B I/O Information B - 1
PC 104 CPU Module B.
PC 104 CPU Module PFM-540I B.
PC 104 CPU Module B.3 IRQ Mapping Chart B.
PC 104 CPU Module PFM-540I Appendix C Mating Connecotor Appendix C Mating Connector C - 1
PC 104 CPU Module PFM-540I C.1 List of Mating Connectors and Cables The table notes mating connectors and available cables.
PC 104 CPU Module CN9 IDE Keentop 1014 Connector CN10 COM1 CN11 Keentop 1014 Power 1701440350 Serial Port Cable 1701100207 Floppy Disk Drive 1701340703 Series Keentop 1014 Connector CN12 IDE Cable Series Connector Floppy PFM-540I Series Ever Cable 2542H-04 N/A Connector CN13 COM2 Keentop 1014 Connector CN14 Ethernet LCD 1701100207 Ethernet Cable 1700100200 Series Keentop 1014 Connector CN15 Serial Port Cable Series HO TIEN 1255H N/A HRS N/A Connector BAT1 Battery Con
