PC/104 CPU Module PFM-541I PFM-541I ® AMD Geode LX800 Processor AMD LX800 + CS5536 Intel 82551ER/IT for 10/100Mbps 24-bit TFT LCD Panel 4 COM, 4USB PFM-541I Manual Rev.A 3rd Ed. Dec.
PC/104 CPU Module PFM-541I Copyright Notice This document is copyrighted, 2009. All rights are reserved. The original manufacturer reserves the right to make improvements to the products described in this manual at any time without notice. No part of this manual may be reproduced, copied, translated, or transmitted in any form or by any means without the prior written permission of the original manufacturer. Information provided in this manual is intended to be accurate and reliable.
PC/104 CPU Module PFM-541I Acknowledgments All other products’ name or trademarks are properties of their respective owners. Award is a trademark of Award Software International, Inc. CompactFlash™ is a trademark of the Compact Flash Association. ® Microsoft Windows is a registered trademark of Microsoft Corp. ® AMD Geode is a registered trademark of Advanced Micro Devices, Inc. ITE is a trademark of Integrated Technology Express, Inc.
PC/104 CPU Module PFM-541I Packing List Before you begin installing your card, please make sure that the following materials have been shipped: 9681540I02 (for standard) Cable Kit for PFM-541I 1701160201 VGA cable x 1 1709100201 USB Cable x 1 1700060152 Keyboard & Mouse Cable x 1 1701440350 44-pin IDE Cable x 1 Quick Installation Guide Utility CD PFM-541I Note: The PFM-541I WiTAS series include the full cable kit because the special cables can be used in rigid environment.
PC/104 CPU Module PFM-541I Contents Chapter 1 General Information 1.1 Introduction................................................................ 1-2 1.2 Features .................................................................... 1-3 1.3 Specifications ............................................................ 1-4 Chapter 2 Quick Installation Guide 2.1 Safety Precautions .................................................... 2-2 2.2 Location of Connectors and Jumpers ....................... 2-3 2.
PC/104 CPU Module PFM-541I 2.18 LPT Port Connector (CN8)...................................... 2-14 2.19 IDE Connector (CN9) .............................................. 2-15 2.20 Power Connector (CN12)........................................ 2-16 2.21 Ethernet Connector (CN14) .................................... 2-16 2.22 LCD Connector (CN15) ........................................... 2-17 2.23 COM1/2/3/4 Connectors (CN16)............................. 2-19 2.24 Ethernet Connector (CN17) .............
PC/104 CPU Module PFM-541I B.3 IRQ Mapping Chart ................................................B-3 B.4 DMA Channel Assignments...................................B-3 Appendix C Mating Connector C.1 List of Mating Connectors and Cables..................
PC/104 CPU Module PFM-541I Chapter 1 General Information Chapter 1 General Information 1- 1
PC/104 CPU Module PFM-541I 1.1 Introduction AAEON Technology, a leading company in embedded boards manufacturing with a full range of PC/104 CPU Modules, launches a brand new PC/104 CPU Module-PFM-541I. Its compact size and rich functionality ensures the most cost effective and compatible module to coincide with your existing system planning devices. PFM-541I adopts an AMD Geode LX800 processor that is more cost effective compared to other PC/104 CPU modules on the market.
PC/104 CPU Module PFM-541I 1.2 Features AMD Geode LX800 Processor Onboard DDR SDRAM, Max. 256MB for DDR333 18/24-bit TFT LCD panel Simultaneous CRT and TFT LCD Display 4 USB 2.
PC/104 CPU Module PFM-541I 1.
PC/104 CPU Module PFM-541I WiTAS series products) Display: Supports CRT/LCD Simultaneous and Dual View Display Chipset AMD LX 800 processor integrated graphics Resolution Up to 1600 x 1200 for CRT Up to 1600 x 1200 @ 24-bit for LCD I/O Storage PATA-33 x 1(supports two ATAPI Devices; CompactFlash Type I Serial Port Four COM ports: internal pin headers for 4 COM ports, RS-232 x 3 (COM1, COM3, COM4), RS-232/422/485 x 1 (COM2) Parallel Port Supports SPP/EPP/ECP mode USB Four USB2.
PC/104 CPU Module PFM-541I Chapter 2 Quick Installation Guide Notice: The Quick Installation Guide is derived from Chapter 2 of user manual. For other chapters and further installation instructions, please refer to the user manual CD-ROM that came with the product. Part No. 2007541I12 Printed in Taiwan, Dec.
PC/104 CPU Module PFM-541I 2.1 Safety Precautions Always completely disconnect the power cord from your board whenever you are working on it. Do not make connections while the power is on, because a sudden rush of power can damage sensitive electronic components. Always ground yourself to remove any static charge before touching the board. Modern electronic devices are very sensitive to static electric charges. Use a grounding wrist strap at all times.
PC/104 CPU Module PFM-541I 2.
PC/104 CPU Module Solder Side Chapter 2 Quick Installation Guide 2 - 4 PFM-541I
PC/104 CPU Module PFM-541I 2.3 Mechanical Drawing 85.09 87.72 90.17 63.50 66.29 15.30 5.08 10.20 0.00 Component Side 96.01 94.18 93.43 90.93 90.93 88.39 84.34 77.98 68.58 65.26 58.08 6.08 34.61 12.97 10.70 5.21 1.81 0.00 9.59 5.21 4.08 1.02 10.30 13.10 90.17 79.28 81.28 84.09 68.14 53.96 56.07 25.66 7.62 7.67 0.00 3.16 5.
PC/104 CPU Module Solder Side Chapter 2 Quick Installation Guide 2 - 6 PFM-541I
PC/104 CPU Module PFM-541I 2.
PC/104 CPU Module PFM-541I 2.5 List of Jumpers The board has a number of jumpers that allow you to configure your system to suit your application.
PC/104 CPU Module PFM-541I 2.6 List of Connectors The board has a number of connectors that allow you to configure your system to suit your application. The table below shows the function of each board's connectors: Note: For further information about mating connectors, please refer to the appendix of manual.
PC/104 CPU Module PFM-541I CN17 Ethernet Connector BAT1 Battery Connector CFD1 Type1 Compact Flash Slot 2.7 Setting Jumpers You configure your card to match the needs of your application by setting jumpers. A jumper is the simplest kind of electric switch. It consists of two metal pins and a small metal clip (often protected by a plastic cover) that slides over the pins to connect them. To “close” a jumper you connect the pins with the clip. To “open” a jumper you remove the clip.
PC/104 CPU Module PFM-541I 2.8 CFD Master/Slave Selection (JP1) JP1 Function 1-2 Slave 2-3 Master (Default) 2.9 RS-232 Ring/5V Selection (JP2) JP2 Function COM1 1-3 +5V 3-5 Ring (Default) COM2 2-4 +5V 4-6 Ring (Default) 2.
PC/104 CPU Module 2.11 Front Panel Connector (CN1) Pin Signal 1 Power LED(+) 2 Power LED(-) 3 N.C 4 Speaker(+) 5 Speaker(-) 6 N.C 7 IDE LED(+) 8 IDE LED(-) 9 N.C 10 Reset(+) 11 Reset(-) 12 N.C 13 Lan1 Speed LED(+) 14 Lan1 Speed LED(-) 15 Lan1 Active LED(+) 16 Lan1 Active LED(-) 17 N.C 18 N.
PC/104 CPU Module PFM-541I 2.12 PS2 Keyboard/Mouse Connector (CN2) Pin Signal Pin Signal 1 KB_DATA 2 KB_CLK 3 GND 4 +5V 5 MS_DATA 6 MS_CLK 2.13 Optional Power Connector (CN3) Pin Signal 1 -12V 2 -5V 3 GND 2.14 USB (3-4) Connector (CN4) Pin Signal Pin Signal 1 +5V 2 GND 3 USBD3- 4 GND 5 USBD3+ 6 USBD4+ 7 GND 8 USBD4- 9 GND 10 +5V 2.
PC/104 CPU Module PFM-541I 5 BLUE 6 N.C 7 N.C 8 DDCDAT 9 GND 10 HSYNC 11 GND 12 VSYNC 13 GND 14 DDCCLK 15 GND 16 GND 2.16 USB (1-2) Connector (CN6) Pin Signal Pin Signal 1 +5V 2 GND 3 USBD1- 4 GND 5 USBD1+ 6 USBD2+ 7 GND 8 USBD2- 9 GND 10 +5V 2.17 PC/104 Connector (CN7) As standard. Note: PFM-541I does not support ISA card with DMA or Master mode in PC/104 interface. 2.
PC/104 CPU Module PFM-541I 7 DATA2 8 #SLIN 9 DATA3 10 GND 11 DATA4 12 GND 13 DATA5 14 GND 15 DATA6 16 GND 17 DATA7 18 GND 19 #ACK 20 GND 21 BUSY 22 GND 23 PE 24 GND 25 SELECT 26 N.C 2.19 IDE Connector (CN9) Pin Signal Pin Signal 1 #RESET 2 GND 3 DATA7 4 DATA8 5 DATA6 6 DATA9 7 DATA5 8 DATA10 9 DATA4 10 DATA11 11 DATA3 12 DATA12 13 DATA2 14 DATA13 15 DATA1 16 DATA14 17 DATA0 18 DATA15 19 GND 20 N.
PC/104 CPU Module PFM-541I 23 #IOW 24 GND 25 #IOR 26 GND 27 IOREADY 28 GND 29 #DACK 30 GND 31 IRQ 32 N.C 33 ADDR1 34 DETECT 35 ADDR0 36 ADDR2 37 #CS0 38 #CS1 39 HDDLED 40 GND 41 +5V 42 +5V 43 GND 44 N.C Note: The IDE interface on PFM-541I only supports two IDE devices. If you use a CF card, there is only one IDE device usable. 2.20 Power Connector (CN12) Pin Signal 1 +5V 2 GND 3 GND 4 +12V 2.
PC/104 CPU Module PFM-541I 3 N.C 4 N.C 5 CHASSIS_GND 6 CHASSIS_GND 7 N.C 8 N.C 9 TX+ 10 TX- 2.22 LCD Connector (CN15) 24-bit TTL Pin Signal Pin Signal 1 +5V 2 +5V 3 GND 4 GND 5 +3.3V 6 +3.
PC/104 CPU Module PFM-541I 33 GND 34 GND 35 CLOCK 36 VSYNC 37 DE 38 HSYNC 39 N.C 40 ENAVEE 18-bit TTL Pin Signal Pin Signal 1 +5V 2 +5V 3 GND 4 GND 5 +3.3V 6 +3.3V 7 ENBKL 8 ENBKL 9 N.C 10 N.C 11 BLUE0 12 BLUE1 13 BLUE2 14 BLUE3 15 BLUE4 16 BLUE5 17 N.C 18 N.C 19 GREEN0 20 GREEN1 21 GREEN2 22 GREEN3 23 GREEN4 24 GREEN5 25 N.C 26 N.
PC/104 CPU Module PFM-541I 35 CLOCK 36 VSYNC 37 DE 38 HSYNC 39 N.C 40 ENAVEE 2.23 COM1/2/3/4 Connectors (CN16) Pin Signal Pin Signal 1 DCD 2 DSR 3 RX 4 RTS 5 TX 6 CTS 7 DTR 8 RI/5V 9 GND 10 N.C 11 DCD (485/422_TX-) 12 DSR 13 RX (422_RX+) 14 RTS 15 TX (485/422_TX+) 16 CTS 17 DTR (422_RX-) 18 RI/5V 19 GND 20 N.C 21 DCD 22 DSR 23 RX 24 RTS 25 TX 26 CTS 27 DTR 28 RI 29 GND 30 N.
PC/104 CPU Module PFM-541I 37 DTR 38 RI 39 GND 40 N.C 2.24 Ethernet Connector (CN17) Pin Signal Pin Signal 1 RX- 2 RX+ 3 N.C 4 N.C 5 CHASSIS_GND 6 CHASSIS_GND 7 N.C 8 N.C 9 TX+ 10 TX- 2.
PC/104 CPU Module PFM-541I Below Table for China RoHS Requirements 产品中有毒有害物质或元素名称及含量 AAEON Main Board/ Daughter Board/ Backplane 有毒有害物质或元素 部件名称 铅 汞 镉 六价铬 多溴联苯 多溴二苯醚 (Pb) (Hg) (Cd) (Cr(VI)) (PBB) (PBDE) × ○ ○ ○ ○ ○ × ○ ○ ○ ○ ○ 印刷电路板 及其电子组件 外部信号 连接器及线材 O：表示该有毒有害物质在该部件所有均质材料中的含量均在 SJ/T 11363-2006 标准规定的限量要求以下。 X：表示该有毒有害物质至少在该部件的某一均质材料中的含量超出 SJ/T 11363-2006 标准规定的限量要求。 备注：此产品所标示之环保使用期限，系指在一般正常使用状况下。 Chapter 2 Quick Installation Guide 2- 21
PC/104 CPU Module PFM-541I Chapter 3 Award BIOS Setup Chapter 3 Award BIOS Setup 3-1
PC/104 CPU Module 3.1 PFM-541I System Test and Initialization These routines test and initialize board hardware. If the routines encounter an error during the tests, you will either hear a few short beeps or see an error message on the screen. There are two kinds of errors: fatal and non-fatal. The system can usually continue the boot up sequence with non-fatal errors.
PC/104 CPU Module 3.2 PFM-541I Award BIOS Setup Awards BIOS ROM has a built-in Setup program that allows users to modify the basic system configuration. This type of information is stored in battery-backed CMOS RAM so that it retains the Setup information when the power is turned off. Entering Setup Power on the computer and press immediately. This will allow you to enter Setup. Standard CMOS Features Use this menu for basic system configuration. (Date, time, IDE, etc.
PC/104 CPU Module PFM-541I system. Frequency/Voltage Control Use this menu to specify your settings for auto detect DIMM/PCI clock and spread spectrum. Load Fail-Safe Defaults Use this menu to load the BIOS default values for the minimal/stable performance for your system to operate. Load Optimized Defaults Use this menu to load the BIOS default values that are factory settings for optimal performance system operations.
PC/104 CPU Module PFM-541I Chapter 4 Driver Installation Chapter 4 Driver Installation 4 - 1
PC/104 CPU Module PFM-541I 4.1 Software Drivers This chapter describes the operation and installation of the display drivers supplied on the Supporting CD-ROM that are shipped with your product. The onboard VGA adapter is based on the AMD LX VGA Flat Panel/CRT controller. This controller offers a large set of extended functions and higher resolutions. The purpose of the enclosed software drivers is to take advantage of the extended features of the AMD LX VGA Flat Panel/CRT controller.
PC/104 CPU Module PFM-541I 4.2 Necessary to Know The instructions in this manual assume that you understand elementary concepts of MS-DOS and the IBM Personal Computer.
PC/104 CPU Module PFM-541I 4.3 Installing VGA Driver Win XP / Win XPe VGA Place the Driver CD-ROM into your CD-ROM drive and follow the steps below to install. 1. Click on Start button. 2. Click on Settings button. 3. Click on Control Panel button. 4. Click on System button. 5. Select Hardware and click on Device Manager…. 6. Double click on Video Controller (VGA Compatible). 7. Click on Update Driver…. 8. Click on Next. 9. Select Search for a suitable driver…, then click on Next. 10.
PC/104 CPU Module PFM-541I 4.4 Installing AES Driver Win XP / Win XPe Geode LX AES Crypto Place the Driver CD-ROM into your CD-ROM drive and follow the steps below to install. 1. Click on Start button. 2. Click on Settings button. 3. Click on Control Panel button. 4. Click on System button. 5. Select Hardware and click on Device Manager…. 6. Double click on Entertainment Encryption/Decryption Controller. 7. Click on Update Driver…. 8. Click on Next. 9.
PC/104 CPU Module PFM-541I 4.5 Installing PCI to ISA Bridge Driver Win XP / Win XPe System Place the Driver CD-ROM into your CD-ROM drive and follow the steps below to install. 1. Click on Start button. 2. Click on Settings button. 3. Click on Control Panel button. 4. Click on System button. 5. Select Hardware and click on Device Manager…. 6. Double click on Other PCI Bridge Device 7. Click on Update Driver…. 8. Click on Next. 9. Select Search for a suitable driver…, then click on Next. 10.
PC/104 CPU Module PFM-541I 4.6 Installing Ethernet Driver Place the Driver CD-ROM into your CD-ROM drive and follow the steps below to install. 1. Click on Start button. 2. Click on Settings button. 3. Click on Control Panel button. 4. Click on System button. 5. Select Hardware and click on Device Manager…. 6. Double click on Ethernet Controller. 7. Click on Update Driver…. 8. Click on Next. 9. Select Search for a suitable driver…, then click on Next. 10. Select Specify a location, then click on Next. 11.
PC/104 CPU Module PFM-541I Appendix A Programming the Watchdog Timer Appendix A Programming the Watchdog Timer A-1
PC/104 CPU Module PFM-541I A.1 Programming PFM-541I utilizes SCH3114-NU chipset as its watchdog timer controller. The SCH311X WDT ( Watch Dog Timer ) has a programmable time-out ranging from 1 to 255 minutes with one minute resolution, or 1 to 255 second resolution. The unit of the WDT timeout value are selected via bit[7] of the WDT_TIMEOUT register. The WDT time-out value is set through the WDT_VAL Runtime register.
PC/104 CPU Module PFM-541I Appendix A Programming the Watchdog Timer A-3
PC/104 CPU Module PFM-541I The following is a sample code to set WDT for 3 seconds. ;Runtime register I/O base address SUPERIO_GPIO_PORT .MODEL EQU 800h SMALL .
PC/104 CPU Module PFM-541I Appendix B I/O Information Appendix B I/O Information B-1
PC/104 CPU Module B.
PC/104 CPU Module PFM-541I B.
PC/104 CPU Module B.3 IRQ Mapping Chart B.
PC/104 CPU Module PFM-541I Appendix C Mating Connecotor Appendix C Mating Connector C - 1
PC/104 CPU Module PFM-541I C.1 List of Mating Connectors and Cables The table notes mating connectors and available cables.
