PC/104 Module PFM-CVS PFM-CVS ® Intel Atom™ N2600 Processor DDR3 1066 SODIMM 18-bit Single Channel LVDS LCD 4 USB2.0, 4 COM, 1 SATA, 1 mSATA 1 Gigabit Ethernet, PC/104+ Mini Card (Optional) PFM-CVS Manual Rev. A 2nd Ed.
PC/104 Module PFM-CVS Copyright Notice This document is copyrighted, 2012. All rights are reserved. The original manufacturer reserves the right to make improvements to the products described in this manual at any time without notice. No part of this manual may be reproduced, copied, translated, or transmitted in any form or by any means without the prior written permission of the original manufacturer. Information provided in this manual is intended to be accurate and reliable.
PC/104 Module PFM-CVS Acknowledgments All other products’ name or trademarks are properties of their respective owners. Intel® and Atom are trademarks of Intel® Corporation. Microsoft Windows is a registered trademark of Microsoft Corp. ITE is a trademark of Integrated Technology Express, Inc. IBM, PC/AT, PS/2, and VGA are trademarks of International Business Machines Corporation. ® All other product names or trademarks are properties of their respective owners.
PC/104 Module PFM-CVS Packing List Before you begin installing your card, please make sure that the following materials have been shipped: Jumper Cap Product CD PFM-CVS with Heatsink If any of these items are missing or damaged, please contact your distributor or sales representative immediately.
PC/104 Module PFM-CVS Contents Chapter 1 General Information 1.1 Introduction................................................................... 1-2 1.2 Features ....................................................................... 1-3 1.3 Specifications ............................................................... 1-4 Chapter 2 Quick Installation Guide 2.1 Safety Precautions ....................................................... 2-2 2.2 Location of Connectors and Jumpers ..........................
PC/104 Module PFM-CVS 2.16 PCI-104 Connector (CN6)........................................ 2-15 2.17 Front Panel Connector (CN7) .................................. 2-15 2.18 +12VSB Power Input Connector (CN9) ................... 2-16 2.19 PC/104/ ISA Connector (CN11) ............................... 2-16 2.20 Digital I/O Connector (CN12) ................................... 2-17 2.21 Mini PCI Express/mSATA Connector (CN14) (Optional) ..........................................................................
PC/104 Module PFM-CVS Chapter 4 Driver Installation 4.1 Installation .................................................................... 4-3 Appendix A Programming The Watchdog Timer A.1 Programming ............................................................A-2 A.2 F81866 Watchdog Timer Initial Program……………A-5 Appendix B I/O Information B.1 I/O Address Map .......................................................B-2 B.2 1st MB Memory Address Map ...................................B-4 B.
PC/104 Module PFM-CVS Chapter 1 General Information Chapter 1 General Information 1- 1
PC/104 Module PFM-CVS 1.1 Introduction AAEON Technology, a leading company in embedded boards manufacturing with a full range of PC/104 Modules, launches a brand new PC/104 CPU Module-PFM-CVS. Its compact size and rich functionality ensures the most cost effective and compatible module to coincide with your existing system planning devices. PFM-CVS adopts an Intel® Atom N2600 Dual Core 1.6 GHz Processor with the latest Intel technology.
PC/104 Module PFM-CVS 1.2 Features Fanless Intel® Atom™ N2600 Dual Core 1.6 GHz Processor Intel® Atom™ N2600 + NM10 204-pin DDR3 1066 MHz SODIMM x 1, Max. 2 GB 10/100/1000Base-TX Ethernet x 1 CRT, 18-bit Single Channel LVDS LCD SATA 3.0 Gb/s x 1 USB2.0 x 4, COM x 4 PC/104+ Standard Form Factor Legacy ISA Support.
PC/104 Module PFM-CVS 1.3 Specifications System Form Factor PC/104 Processor Intel® Atom™ N2600 1.6 GHz processor System Memory DDR3 1066 MHz SODIMM x 1, Max.
PC/104 Module PFM-CVS Operating Temperature 32ºF ~ 140ºF (0ºC ~ 60ºC); -4ºF ~ 158ºF (-20ºC ~ 70ºC) for WiTAS1 Storage Temperature -40ºF ~ 176ºF (-40ºC ~ 80ºC) Operating Humidity 0%~90% relative humidity, non-condensing Display: Supports CRT/LCD simultaneous/ dual view displays Chipset Intel® Atom™ N2600 processor integrated Resolutions Up to 1920x1200 for CRT; Up to 1366x768 for LVDS LCD Interface 18-bit Single Channel LVDS Storage SATA 3.
PC/104 Module PFM-CVS Limitation Notice on ISA Interface Support According to the information from Intel for Atom™ Processor design, Intel® Atom™ Processor D2000 and N2000 Series do NOT support ISA expansion area (C_0000h-D_FFFFh). This area always maps to system DRAM. The illustration is as below for reference. Document source: Intel® Atom™ Processor D2000 and N2000 Series page 34 mentions that is External Design Specification – Volume 2 of 2.
PC/104 Module PFM-CVS Chapter 2 Quick Installation Guide Chapter 2 Quick Installation Guide 2-1
PC/104 Module PFM-CVS 2.1 Safety Precautions Always completely disconnect the power cord from your board whenever you are working on it. Do not make connections while the power is on, because a sudden rush of power can damage sensitive electronic components. Always ground yourself to remove any static charge before touching the board. Modern electronic devices are very sensitive to static electric charges. Use a grounding wrist strap at all times.
PC/104 Module PFM-CVS 2.
PC/104 Module Solder Side Chapter 2 Quick Installation Guide 2-4 PFM-CVS
PC/104 Module PFM-CVS 2.
PC/104 Module Solder Side Chapter 2 Quick Installation Guide 2-6 PFM-CVS
PC/104 Module PFM-CVS 2.4 List of Jumpers The board has a number of jumpers that allow you to configure your system to suit your application.
PC/104 Module PFM-CVS 2.5 List of Connectors The board has a number of connectors that allow you to configure your system to suit your application.
PC/104 Module PFM-CVS FAN1 FAN Connector(Reserved) LAN1 LAN Connector DIMM1 DDR3 SODIMM Connector Chapter 2 Quick Installation Guide 2-9
PC/104 Module PFM-CVS 2.6 Setting Jumpers You configure your card to match the needs of your application by setting jumpers. A jumper is the simplest kind of electric switch. It consists of two metal pins and a small metal clip (often protected by a plastic cover) that slides over the pins to connect them. To “close” a jumper you connect the pins with the clip. To “open” a jumper you remove the clip. Sometimes a jumper will have three pins, labeled 1, 2 and 3.
PC/104 Module PFM-CVS 2.7 LVDS Voltage Selection (JP2) 1 2 3 1 2 3 +5V +3.3V JP2 Function 1-2 +5V 2-3 +3.3V (Default) 2.
PC/104 Module PFM-CVS 2.9 COM2 +5V/Ring/+12V Selection (JP6) 1 3 5 2 4 6 +12V 1 3 5 2 4 6 1 3 5 Ring 2 4 6 +5V JP6 Function 1-2 +12V 3-4 Ring (Default) 5-6 +5V 2.10 PCI-104 VIO Voltage Selection (JP7) 1 2 3 1 2 3 +5V +3.3V JP7 Function 1-2 +5V 2-3 +3.3V (Default) 2.
PC/104 Module PFM-CVS 2.12 PC/104 -5V/-12V Voltage Selection (JP11) Reserved -12V -5V GND JP11 Function 1 -12V 2 -5V 3 GND 2.13 Backlight Brightness Control Connector (CN2) Pin Pin Name Signal Type 1 LVDS Voltage select OUT 2 LVDS Backlight control OUT 3 GND GND 4 GND GND 5 LVDS Backlight Enable OUT Signal Level Note: LVDS Voltage can be set to +5V or +12V by JP3.
PC/104 Module PFM-CVS 2.14 Internal LVDS Connector (CN3) Pin Pin Name Signal Type 1 LVDS_BKLEN OUT 2 LVDS_BKLCTL OUT 3 LVDS Voltage PWR 4 LVDS Voltage PWR 5 LVDS_CLKN OUT 6 LVDS_TX2 OUT 7 LVDS_CLKP OUT 8 LVDS_TX#2 OUT 9 LVDS Voltage PWR 10 GND GND 11 LVDS_TX0 OUT 12 LVDS_TX3 OUT 13 LVDS_TX#0 OUT 14 LVDS_TX#3 OUT 15 GND GND Chapter 2 Quick Installation Guide 2-14 Signal Level +3.3V/ +5V +3.3V/ +5V +3.
PC/104 Module PFM-CVS 16 GND GND 17 LVDS_TX1 OUT 18 LVDS_DDCDAT I/O 19 LVDS_TX#1 OUT 20 LVDS_DDCCLK I/O +3.3V +3.3V 2.15 SATA Power Connector (CN5) Pin Pin Name Signal Type Signal Level 1 +5V PWR +5V 2 GND GND GND Signal Level 2.16 PCI-104 Connector (CN6) Standard PCI-104 Slot 2.
PC/104 Module PFM-CVS 2 POWRR BUTTON# IN 3 External Buzzer(+) OUT 4 External Buzzer(-) OUT 5 HDD LED OUT 6 HDD LED# OUT 7 POWER LED OUT 8 POWER LED# OUT 9 RESET IN 10 RESET# IN 2.18 +12VSB Power Input Connector (CN9) Pin Pin Name Signal Type Signal Level 1 +12VSB PWR +12V 2 GND GND 2.
PC/104 Module PFM-CVS 2.20 Digital I/O Connector (CN12) Note: The DIO function has no ESD protection. non-isolation function. Pin Pin Name Signal type 1 GPI0 IN 2 GPI1 IN 3 GPI2 IN 4 GPI3 IN 5 GPO0 OUT 6 GPO1 OUT 7 GPO2 OUT 8 GPO3 OUT 9 +3.3V PWR 10 GND GND It is only for Signal Level +3.3V 2.
PC/104 Module PFM-CVS Pin Pin Name Signal Type 1 WAKE# I/O 2 +3V3_MC PWR 3 Reserved 4 GND 5 Reserved 6 +1.5V PWR 7 MC_CLKREQ# I/O 8 Reserved 9 GND 10 Reserved 11 PCIE_MC_CKLN 12 Reserved 13 PCIE_MC_CKLP 14 Reserved 15 GND 16 Reserved 17 Reserved 18 GND 19 Reserved 20 W_DISABLE# 21 GND GND 22 BUF_PLTRST# IN 23 PCIE_RXN1 DIFF Chapter 2 Quick Installation Guide 2-18 Signal Level +3.3V GND GND OUT OUT GND GND +1.
PC/104 Module PFM-CVS 24 +3V3_MC PWR 25 PCIE_RXP1 DIFF 26 GND GND 27 GND GND 28 +1.5V PWR 29 GND GND 30 SMBCLK_SBY I/O 31 PCIE_TXN1 DIFF 32 SMBDAT_SBY I/O 33 PCIE_TXP1 DIFF 34 GND GND 35 GND GND 36 USBP4- DIFF 37 GND GND 38 USBP4+ DIFF 39 +3V3_MC PWR 40 GND GND 41 +3V3_MC PWR 42 Reserved 43 GND 44 Reserved 45 Reserved 46 Reserved 47 Reserved +3.3V +1.5V +3.3V +3.
PC/104 Module 48 +1.5V 49 Reserved 50 GND 51 Reserved 52 +3V3_MC PFM-CVS PWR +1.5V GND PWR +3.3V Signal Level Standard mSATA Connector (52 Pins) Pin Pin Name Signal Type 1 WAKE# I/O 2 +3V3_MC PWR 3 Reserved 4 GND 5 Reserved 6 +1.5V PWR 7 MC_CLKREQ# I/O 8 Reserved 9 GND 10 Reserved 11 PCIE_MC_CKLN 12 Reserved Chapter 2 Quick Installation Guide 2-20 +3.3V GND GND OUT +1.
PC/104 Module PFM-CVS 13 PCIE_MC_CKLP OUT 14 Reserved 15 GND 16 Reserved 17 Reserved 18 GND 19 Reserved 20 W_DISABLE# 21 GND GND 22 BUF_PLTRST# IN 23 SATA_RXP1 DIFF 24 +3V3_MC PWR 25 SATA_RXN1 DIFF 26 GND GND 27 GND GND 28 +1.5V PWR 29 GND GND 30 SMBCLK_SBY I/O 31 SATA_TXN1 DIFF 32 SMBDAT_SBY I/O 33 SATA_TXP1 DIFF 34 GND GND 35 GND GND 36 USBP4- DIFF GND GND +3.3V +1.
PC/104 Module PFM-CVS 37 GND GND 38 USBP4+ DIFF 39 +3V3_MC PWR 40 GND GND 41 +3V3_MC PWR 42 Reserved 43 NC 44 Reserved 45 Reserved 46 Reserved 47 Reserved I/O 48 +1.5V PWR 49 Reserved I/O 50 GND GND 51 Reserved I/O 52 +3V3_MC PWR +3.3V +3.3V I/O +1.5V +3.3V 2.22 Battery Connector (BT1) Pin Pin Name Signal Type Signal Level 1 RTCBAT PWR +3.
PC/104 Module PFM-CVS 2.23 SATA Connector (SATA1) Pin Pin Name Signal Type 1 GND GND 2 SATA_TXP0 DIFF 3 SATA_TXN0 DIFF 4 GND GND 5 SATA_RXN0 DIFF 6 SATA_RXP0 DIFF 7 GND GND Signal Level 2.
PC/104 Module PFM-CVS 3 GND GND 4 SCL I/O +5V 5 SDA I/O +5V 6 GND GND 7 BLUE OUT 8 GND GND 9 GREEN OUT 10 GND GND 11 RED OUT 12 GND GND 13 VCC PWR +5V 2.
PC/104 Module PFM-CVS 7 DTR1 OUT 8 RI1 IN 9 GND GND ±9V 2.
PC/104 Module PFM-CVS 2 N.C 3 RX+ 4 N.C 5 TX+ 6 N.C 7 RX- IN 8 +5V/+12V PWR 9 GND GND Pin Pin Name Signal Type Signal Level 1 B (Data-) I/O ±5V 2 N.C 3 N.C 4 N.C 5 A (Data+) I/O ±5V 6 N.C 7 N.C 8 +5V/+12V PWR +5V/+12V 9 GND GND IN OUT ±5V +5V/+12V RS-485 2.
PC/104 Module PFM-CVS Pin Pin Name Signal Type Signal Level 1 DCD3 IN 2 DSR3 IN 3 RXD3 IN 4 RTS3 OUT ±9V 5 TXD3 OUT ±9V 6 CTS3 IN 7 DTR3 OUT 8 RI3 IN 9 GND GND ±9V 2.
PC/104 Module PFM-CVS 8 RI4 IN 9 GND GND 2.29 USB2.0 Connector (USB1) Pin Pin Name Signal Type Signal Level 1 USB_VCC0 PWR +5V 2 USBP0- OUT 3 USBP0+ OUT 4 GND GND 5 GND GND 2.30 USB2.
PC/104 Module PFM-CVS 2.31 USB2.0 Connector (USB3) Pin Pin Name Signal Type Signal Level 1 USB_VCC1 PWR +5V 2 USBP2- OUT 3 USBP2+ OUT 4 GND GND 5 GND GND 2.32 USB2.
PC/104 Module PFM-CVS 2.33 FAN Connector (FAN1) Reserved Pin Pin Name Signal Type 1 GND GND 2 FAN_CTL OUT 3 FAN_TAC IN Signal Level 2.34 LAN Connector (LAN1) Pin Pin Name Signal Type 1 LAN1_TX1+ DIFF. 2 LAN1_TX1- DIFF. 3 LAN1_RX1+ DIFF. 4 LAN1_RX1- DIFF. 5 GND GND 6 GND GND 7 LAN1_TX2+ DIFF. 8 LAN1_TX2- DIFF.
PC/104 Module 10 LAN1_RX2- PFM-CVS DIFF 2.
PC/104 Module PFM-CVS Below Table for China RoHS Requirements 产品中有毒有害物质或元素名称及含量 AAEON Main Board/ Daughter Board/ Backplane 有毒有害物质或元素 部件名称 铅 汞 镉 六价铬 多溴联苯 多溴二苯醚 (Pb) (Hg) (Cd) (Cr(VI)) (PBB) (PBDE) × ○ ○ ○ ○ ○ × ○ ○ ○ ○ ○ 印刷电路板 及其电子组件 外部信号 连接器及线材 O：表示该有毒有害物质在该部件所有均质材料中的含量均在 SJ/T 11363-2006 标准规定的限量要求以下。 X：表示该有毒有害物质至少在该部件的某一均质材料中的含量超出 SJ/T 11363-2006 标准规定的限量要求。 备注：此产品所标示之环保使用期限，系指在一般正常使用状况下。 Chapter 2 Quick Installation Guide 2-32
PC/104 Module PFM-CVS Chapter 3 AMI BIOS Setup Chapter 3 AMI BIOS Setup 3-1
PC/104 Module PFM-CVS 3.1 System Test and Initialization These routines test and initialize board hardware. If the routines encounter an error during the tests, you will either hear a few short beeps or see an error message on the screen. There are two kinds of errors: fatal and non-fatal. The system can usually continue the boot up sequence with non-fatal errors. System configuration verification These routines check the current system configuration stored in the CMOS memory and BIOS NVRAM.
PC/104 Module PFM-CVS 3.2 AMI BIOS Setup AMI BIOS ROM has a built-in Setup program that allows users to modify the basic system configuration. This type of information is stored in battery-backed CMOS RAM and BIOS NVRAM so that it retains the Setup information when the power is turned off. Entering Setup Power on the computer and press or immediately. This will allow you to enter Setup. Main Set the date, use tab to switch between date elements.
PC/104 Module Setup Menu Setup submenu: Main Chapter 3 AMI BIOS Setup 3-4 PFM-CVS
PC/104 Module PFM-CVS Setup submenu: Advanced Chapter 3 AMI BIOS Setup 3-5
PC/104 Module PFM-CVS ACPI Settings Options summary : Suspend mode S3 (Suspend to RAM) Select the ACPI state used for System Suspend Chapter 3 AMI BIOS Setup 3-6 Optimal Default, Failsafe Default
PC/104 Module PFM-CVS CPU Configuration Options summary : Hyper-Threading Disabled Enabled En/Disable CPU Hyper-Threading function Optimal Default, Failsafe Default Chapter 3 AMI BIOS Setup 3-7
PC/104 Module IDE Configuration (IDE) Chapter 3 AMI BIOS Setup 3-8 PFM-CVS
PC/104 Module PFM-CVS IDE Configuration (AHCI) Options summary : SATA Controllers Disabled Enabled Default En/Disable SATA Controller. SATA Mode IDE Default AHCI IDE: Configure SATA controllers as legacy IDEAHCI: Configure SATA controllers to operate in AHCI mode Hot Plug Disabled Enabled Optimal Default, Failsafe Default En/Disable Hot Plug feature.
PC/104 Module PFM-CVS USB Configuration Options summary : Legacy USB Support Enabled Optimal Default, Failsafe Default Disabled Auto Enables BIOS Support for Legacy USB Support. When enabled, USB can be functional in legacy environment like DOS. AUTO option disables legacy support if no USB devices are connected Device Name (Emulation Auto Optimal Default, Failsafe Default Type) Floppy Forced FDD Hard Disk CDROM If Auto.
PC/104 Module PFM-CVS F81866 Super IO Configuration Chapter 3 AMI BIOS Setup 3-11
PC/104 Module Serial Port Configuration Chapter 3 AMI BIOS Setup 3-12 PFM-CVS
PC/104 Module PFM-CVS Chapter 3 AMI BIOS Setup 3-13
PC/104 Module Chapter 3 AMI BIOS Setup 3-14 PFM-CVS
PC/104 Module PFM-CVS Options summary : Serial Port Disabled Enabled Default Allows BIOS to En/Disable correspond serial port. Change Settings Auto Default (Serial Port 1) IO=3F8h; IRQ=4; IO=3F8h; IRQ=3,4; IO=2F8h; IRQ=3,4; Allows BIOS to Select Serial Port resource. Change Settings Auto Default (Serial Port 2) IO=2F8h; IRQ=3; IO=3F8h; IRQ=3,4; IO=2F8h; IRQ=3,4; Allows BIOS to Select Serial Port resource.
PC/104 Module F81866 H/W Monitor Chapter 3 AMI BIOS Setup 3-16 PFM-CVS
PC/104 Module PFM-CVS Digital IO Options summary : DIO_P#1~4 Input Default Output Allows BIOS to select input/output function to corresponding DIO ping. DIO_P#5~8 Input Output Default Allows BIOS to select input/output function to corresponding DIO ping. DIO_P#1~8 Direction Low Hi Default Allows BIOS to select high/low voltage level to output to corresponding DIO ping.
PC/104 Module Setup submenu: Chipset Chapter 3 AMI BIOS Setup 3-18 PFM-CVS
PC/104 Module PFM-CVS Host Bridge Chapter 3 AMI BIOS Setup 3-19
PC/104 Module Graphics Configuration Chapter 3 AMI BIOS Setup 3-20 PFM-CVS
PC/104 Module PFM-CVS Options summary : Fixed Graphics Memory 128MB Size 256MB Default Select the amount of system memory used by the Internal graphics device. IGFX - Boot Type VBIOS Default Default CRT LFP Select boot display device. Active LFP No LVDS LVDS Default En/Disable LVDS interface LCD Panel Type VBIOS Default Default 640x480 18bit 800x600 18bit 1024x768 18bit 1366x768 18bit 1280x768 18bit Select panel native resolution.
PC/104 Module PFM-CVS South Bridge Options summary : Power Mode ATX Type AT Type Default Select Power Mode: ATX Type: Normal ACPI support AT Type: Suspend/Sleep disabled, and Always On when restoring from power failure.
PC/104 Module PFM-CVS Setup submenu: Boot Options summary : Quiet Boot Disabled Enabled En/Disable showing boot logo.
PC/104 Module BBS Priorities Chapter 3 AMI BIOS Setup 3-24 PFM-CVS
PC/104 Module PFM-CVS Security Change User/Supervisor Password You can install a Supervisor password, and if you install a supervisor password, you can then install a user password. A user password does not provide access to many of the features in the Setup utility. If you highlight these items and press Enter, a dialog box appears which lets you enter a password. You can enter no more than six letters or numbers. Enter after you have typed in the password. retype the password for confirmation.
PC/104 Module PFM-CVS Removing the Password Highlight this item and type in the current password. Enter to disable password protection.
PC/104 Module PFM-CVS Setup submenu: Exit Chapter 3 AMI BIOS Setup 3-27
PC/104 Module PFM-CVS Chapter 4 Driver Installation Chapter 4 Driver Installation 4 - 1
PC/104 Module PFM-CVS The PFM-CVS comes with a CD-ROM that contains all drivers and utilities that meet your needs. Follow the sequence below to install the drivers: Step 1 – Install Chipset Driver Step 2 – Install VGA Driver Step 3 – Install LAN Driver Step 4 – Install Serial Port Driver (Optional) Step 5 – Install Rapid Storage Technology Step 6 – Install AHCI for XP Installation Please read instructions below for further detailed installations.
PC/104 Module PFM-CVS 4.1 Installation: Insert the PFM-CVS CD-ROM into the CD-ROM Drive. And install the drivers from Step 1 to Step 6 in order. Step 1 – Install Chipset Driver 1. Click on the Step 1 – Chipset folder and double click on the Setup.exe file 2. Follow the instructions that the window shows 3. The system will help you install the driver automatically Step 2 – Install VGA Driver 1. Click on the Step 2 – VGA folder and select the OS your system is 2. Double click on the .
PC/104 Module PFM-CVS Step 4 – Install Serial Port Driver (Optional) For Windows® XP 32-bit 1. Click on the STEP4 - Serial Port Driver (Optional) folder and select the OS folder of WINXP_32 2. Double click on the patch.bat file 3. The system will help you install the driver automatically 4.
PC/104 Module PFM-CVS For Windows® 7 32-bit/ 64-bit 1.
PC/104 Module 2. Restart the operating system.
PC/104 Module PFM-CVS 3. Click on the STEP4 - Serial Port Driver (Optional) folder and select the OS folder. 4. Right click on the patch.bat file and select Run as administrator 5. The system will help you install the driver automatically. 6. Check the driver installation in the device manager.
PC/104 Module PFM-CVS Step 5 – Install Rapid Storage Technology 1. Click on the Step5 - Rapid Storage Technology folder and select the OS your system is 2. Double click on the setup.exe file located in each OS folder 3. Follow the instructions that the window shows 4.
PC/104 Module PFM-CVS Step 1: Copy the files below from “Driver CD” -> “Step6 - AHCI for XP installation” to Disk.
PC/104 Module PFM-CVS Step 4: Choose “S” Step 5: Choose “Intel(R) NM10 Express Chipset” Chapter 4 Driver Installation 4 - 10
PC/104 Module PFM-CVS Step 6: It will show the model number you select and then press “ENTER” Step 7: Setup is starting Windows Chapter 4 Driver Installation 4 - 11
PC/104 Module PFM-CVS Appendix A Programming the Watchdog Timer Appendix A Programming the Watchdog Timer A-1
PC/104 Module PFM-CVS A.1 Programming PFM-CVS utilizes FINTEK 81866 chipset as its watchdog timer controller. Below are the procedures to complete its configuration and the AAEON initial watchdog timer program is also attached based on which you can develop customized program to fit your application. Configuring Sequence Description After the hardware reset or power-on reset, the FINTEK 81866 enters the normal mode with all logical devices disabled except KBC.
PC/104 Module PFM-CVS There are three steps to complete the configuration setup: (1) Enter the MB PnP Mode; (2) Modify the data of configuration registers; (3) Exit the MB PnP Mode. Undesired result may occur if the MB PnP Mode is not exited normally. (1) Enter the MB PnP Mode To enter the MB PnP Mode, four special I/O write operations are to be performed during Wait for Key state.
PC/104 Module PFM-CVS Watch Dog Timer 1, 2, 3 Control Register (Index=F5h,F6h,FAh Default=00h) Appendix A Programming the Watchdog Timer A-4
PC/104 Module PFM-CVS A.
PC/104 Module PFM-CVS Void aaeonWdtSetTimeoutCount(BYTE tTimeout){ f81866SetLdn(0x07); f81866WriteByte(F81866_WDT_TIME_REG, tTimeout); } Void aaeonWdtSetEnable(BOOL bEnable){ f81866SetLdn(0x07); if(bEnable){ f81866WriteByte(0x30, 0x01); WDT_BASE_ADDR = (f81866ReadByte(F81866_WDT_BASEADDR_REG_MSB) << 8) | f81866ReadByte(F81866_WDT_BASEADDR_REG_LSB); WDT_STATUS = f81866ReadByte(F81866_WDT_CONTROL_REG); f81866WriteByte(F81866_WDT_CONTROL_REG, WDT_STATUS | 0x20); WDT_STATUS = f81866ReadByte(F81866_WDT_PME_RE
PC/104 Module PFM-CVS Void aaeonSuperIOClose(){ aaeonioWritePortByte(F81866_INDEX, 0xaa); } Appendix A Programming the Watchdog Timer A-7
PC/104 Module PFM-CVS Appendix B I/O Information Appendix B I/O Information B-1
PC/104 Module B.
PC/104 Module PFM-CVS Appendix B I/O Information B-3
PC/104 Module B.
PC/104 Module PFM-CVS B.
PC/104 Module Appendix B I/O Information B-6 PFM-CVS
PC/104 Module PFM-CVS B.
PC/104 Module PFM-CVS Appendix C Mating Connector Appendix C Mating Connector C - 1
PC/104 Module PFM-CVS C.1 List of Mating Connectors and Cables The table notes mating connectors and available cables. Connector Function Label Mating Connector Vendor CN2 CN3 CN5 CN7 CN7 CN7 CN9 CN12 CN12 LAN1 VGA1 COM1 Model number Backlight CATCH H738-05 Brightness Control (Dummy) Internal HIROSE DF13-20S-1.
PC/104 Module COM2 COM3 COM4 USB1 USB2 USB3 USB4 COM2 RS232/422/ 485 Connector COM3 RS232 Connector COM4 RS232 Connector USB2.0 Connector USB2.0 Connector USB2.0 Connector USB2.
PC/104 Module PFM-CVS Appendix D Electrical Specifications for I/O Ports Appendix D Electrical Specifications for I/O Ports D-1
PC/104 Module PFM-CVS D.1 Electrical Specifications for I/O Ports I/O Backlight Brightness Control Connector Iternal LVDS Connector SATA Power Connector Digital I/O Connector Mini PCI Express/mSATA Connector CRT Connector COM2 RS232/422/485 Connector USB2.0 Connector USB2.0 Connector USB2.0 Connector USB2.0 Connector Reference Signal Name Rate Output CN2 VDD +5V/0.5 or +12V/0.5 CN3 VCC +3.3V/1A or +5V/1A CN5 +5V +5V/1A CN12 D0~D7 +3.3V/(Open drain) CN14 +3.3VSB +1.5V +3.3V/1.1A +1.5V/0.
PC/104 Module PFM-CVS D.2 DIO Programming PFM-CVS utilizes FINTEK 81866 chipset as its Digital I/O controller. Below are the procedures to complete its configuration and the AAEON initial watchdog timer program is also attached based on which you can develop customized program to fit your application. There are three steps to complete the configuration setup: (1) Enter the MB PnP Mode; (2) Modify the data of configuration registers; (3) Exit the MB PnP Mode.
PC/104 Module PFM-CVS D.
PC/104 Module PFM-CVS 91 GPIO6 Output Data Register 92 GPIO6 Pin Status Register 80 GPIO7 Output Enable Register 81 GPIO7 Output Data Register 82 GPIO7 Pin Status Register 88 GPIO8 Output Enable Register 89 GPIO8 Output Data Register 8A GPIO8 Pin Status Register Appendix D Electrical Specifications for I/O Ports D-5
PC/104 Module PFM-CVS D.
PC/104 Module PFM-CVS } Else(Read Digital Input?){ // Read Digital Input Status, High/Low ? // Example : // GPIO8x GPIOPinStatusRegister = 0x8A // GPIO7x GPIOPinStatusRegister = 0x82 ByteData = f81866ReadByte(GPIOPinStatusRegister); // If ByteDate = 0xF0 // GPIOx4~GPIOx7 Pin Status is High } aaeonSuperIOClose(); } Void aaeonSuperIOOpen(){ // Config F81866 Entry key aaeonioWritePortByte(F81866_INDEX, 0x87); aaeonioWritePortByte(F81866_INDEX, 0x87); } Void aaeonSuperIOClose(){ aaeonioWritePortByte(F8186
