PC/104 Module PFM-CVS Rev. B PFM-CVS Rev.B ® Intel Atom™ N2600 Processor DDR3 1067MHz SODIMM 18-bit Single Channel LVDS LCD 4 USB2.0, 4 COM, 1 SATA, 1 mSATA 1 10/100/1000Base-TX Ethernet, PC/104+ Half/Full size Mini Card (Optional) PFM-CVS Rev.
PC/104 Module PFM-CVS Rev. B Copyright Notice This document is copyrighted, 2013. All rights are reserved. The original manufacturer reserves the right to make improvements to the products described in this manual at any time without notice. No part of this manual may be reproduced, copied, translated, or transmitted in any form or by any means without the prior written permission of the original manufacturer. Information provided in this manual is intended to be accurate and reliable.
PC/104 Module PFM-CVS Rev. B Acknowledgments All other products’ name or trademarks are properties of their respective owners. Intel® and Atom™ are trademarks of Intel® Corporation. Microsoft Windows is a registered trademark of Microsoft Corp. ITE is a trademark of Integrated Technology Express, Inc. IBM, PC/AT, PS/2, and VGA are trademarks of International Business Machines Corporation. ® All other product names or trademarks are properties of their respective owners.
PC/104 Module PFM-CVS Rev. B Packing List Before you begin installing your card, please make sure that the following materials have been shipped: Jumper Cap Product CD PFM-CVS Rev. B with Heatsink If any of these items are missing or damaged, please contact your distributor or sales representative immediately.
PC/104 Module PFM-CVS Rev. B Contents Chapter 1 General Information 1.1 Introduction................................................................... 1-2 1.2 Features ....................................................................... 1-3 1.3 Specifications ............................................................... 1-4 Chapter 2 Quick Installation Guide 2.1 Safety Precautions ....................................................... 2-2 2.2 Location of Connectors and Jumpers ....................
PC/104 Module PFM-CVS Rev. B 2.16 PCI-104 Connector (CN6)........................................ 2-15 2.17 Front Panel Connector (CN7) .................................. 2-15 2.18 +12VSB Power Input Connector (CN9) ................... 2-16 2.19 PC/104/ ISA Connector (CN11) ............................... 2-16 2.20 Digital I/O Connector (CN12) ................................... 2-17 2.21 Mini PCI Express/mSATA Connector (CN14) (Optional) ...................................................................
PC/104 Module PFM-CVS Rev. B 3.2 AMI BIOS Setup ........................................................... 3-3 Chapter 4 Driver Installation 4.1 Installation .................................................................... 4-3 Appendix A Programming The Watchdog Timer A.1 Watchdog Timer Initial Program ...............................A-2 Appendix B I/O Information B.1 I/O Address Map .......................................................B-2 B.2 1st MB Memory Address Map ...........................
PC/104 Module PFM-CVS Rev.
PC/104 Module PFM-CVS Rev. B 1.1 Introduction AAEON Technology, a leading company in embedded boards manufacturing with a full range of PC/104 Modules, launches a brand new PC/104 CPU Module-PFM-CVS Rev. B. Its compact size and rich functionality ensures the most cost effective and compatible module to coincide with your existing system planning devices. PFM-CVS Rev. B adopts an Intel® Atom™ N2600 Dual Core 1.6 GHz Processor with the latest Intel technology. Although PFM-CVS Rev.
PC/104 Module PFM-CVS Rev. B 1.2 Features z Fanless Intel® Atom™ N2600 Dual Core 1.6 GHz Processor z Intel® Atom™ N2600 + NM10 z 204-pin DDR3 1067 MHz SODIMM x 1, Max. 2 GB z 10/100/1000Base-TX Ethernet x 1 z CRT, 18-bit Single Channel LVDS LCD z SATA 3.0 Gb/s x 1 z 2CH HD Audio z USB2.0 x 4, COM x 4 z PC/104+ Standard Form Factor Legacy ISA Support.
PC/104 Module PFM-CVS Rev. B 1.3 Specifications System z Form Factor PC/104 z Processor Intel® Atom™ N2600 1.6 GHz processor z System Memory 204-pin DDR3 1067 MHz SODIMM x 1, Max.
PC/104 Module z PFM-CVS Rev. B Operating Temperature 32°F~ 140°F (0°C ~ 60°C) WiTAS 2 : -40°F~ 185°F (-40°C~85°C) (PFM-CVSW2-B10) z Storage Temperature 32ºF ~ 140ºF (0ºC ~ 60ºC) z Operating Humidity 0%~90% relative humidity, non-condensing Display: Supports CRT/LCD simultaneous/ dual view displays z Chipset Intel® Atom™ N2600 processor integrated z Resolutions Up to 1920x1200 for VGA; Up to 1366x768 for LVDS z LCD Interface 18-bit Single Channel LVDS z Storage SATA 3.
PC/104 Module PFM-CVS Rev. B thermal module is “SARCON® XR-HL” (1.2 W/m-K) or better.
PC/104 Module PFM-CVS Rev. B Limitation Notice on ISA Interface Support According to the information from Intel for Atom™ Processor design, Intel® Atom™ Processor D2000 and N2000 Series do NOT support ISA expansion area (C_0000h-D_FFFFh). This area always maps to system DRAM. The illustration is as below for reference. Document source: Intel® Atom™ Processor D2000 and N2000 Series page 34 mentions that is External Design Specification – Volume 2 of 2.
PC/104 Module PFM-CVS Rev.
PC/104 Module PFM-CVS Rev. B 2.1 Safety Precautions Always completely disconnect the power cord from your board whenever you are working on it. Do not make connections while the power is on, because a sudden rush of power can damage sensitive electronic components. Always ground yourself to remove any static charge before touching the board. Modern electronic devices are very sensitive to static electric charges. Use a grounding wrist strap at all times.
PC/104 Module PFM-CVS Rev. B 2.
PC/104 Module Solder Side Chapter 2 Quick Installation Guide 2-4 PFM-CVS Rev.
PC/104 Module PFM-CVS Rev. B 2.
PC/104 Module Solder Side Chapter 2 Quick Installation Guide 2-6 PFM-CVS Rev.
PC/104 Module PFM-CVS Rev. B 2.4 List of Jumpers The board has a number of jumpers that allow you to configure your system to suit your application.
PC/104 Module PFM-CVS Rev. B 2.5 List of Connectors The board has a number of connectors that allow you to configure your system to suit your application.
PC/104 Module PFM-CVS Rev.
PC/104 Module PFM-CVS Rev. B 2.6 Setting Jumpers You configure your card to match the needs of your application by setting jumpers. A jumper is the simplest kind of electric switch. It consists of two metal pins and a small metal clip (often protected by a plastic cover) that slides over the pins to connect them. To “close” a jumper you connect the pins with the clip. To “open” a jumper you remove the clip. Sometimes a jumper will have three pins, labeled 1, 2 and 3.
PC/104 Module PFM-CVS Rev. B 2.7 LVDS Voltage Selection (JP2) 1 2 3 1 2 3 +5V +3.3V JP2 Function 1-2 +5V 2-3 +3.3V (Default) 2.
PC/104 Module PFM-CVS Rev. B 2.9 COM2 +5V/Ring/+12V Selection (JP6) 1 3 5 2 4 6 +12V 1 3 5 2 4 6 1 3 5 Ring 2 4 6 +5V JP6 Function 1-2 +12V 3-4 Ring (Default) 5-6 +5V 2.10 PCI-104 VIO Voltage Selection (JP7) 1 2 3 1 2 3 +5V +3.3V JP7 Function 1-2 +5V 2-3 +3.3V (Default) 2.
PC/104 Module PFM-CVS Rev. B 2.12 PC/104 -5V/-12V Voltage Selection (JP11) Reserved -12V -5V GND JP11 Function 1 -12V 2 -5V 3 GND 2.13 Backlight Brightness Control Connector (CN2) Pin Pin Name Signal Type 1 LVDS Voltage select OUT 2 LVDS Backlight control OUT 3 GND GND 4 GND GND 5 LVDS Backlight Enable OUT Signal Level Note: LVDS Voltage can be set to +5V or +12V by JP3.
PC/104 Module PFM-CVS Rev. B 2.14 Internal LVDS Connector (CN3) Pin Pin Name Signal Type 1 LVDS_BKLEN OUT 2 LVDS_BKLCTL OUT 3 LVDS Voltage PWR 4 LVDS Voltage PWR 5 LVDS_CLKN OUT 6 LVDS_TX2 OUT 7 LVDS_CLKP OUT 8 LVDS_TX#2 OUT 9 LVDS Voltage PWR 10 GND GND 11 LVDS_TX0 OUT 12 LVDS_TX3 OUT 13 LVDS_TX#0 OUT 14 LVDS_TX#3 OUT 15 GND GND Chapter 2 Quick Installation Guide 2-14 Signal Level +3.3V/ +5V +3.3V/ +5V +3.
PC/104 Module PFM-CVS Rev. B 16 GND GND 17 LVDS_TX1 OUT 18 LVDS_DDCDAT I/O 19 LVDS_TX#1 OUT 20 LVDS_DDCCLK I/O +3.3V +3.3V 2.15 SATA Power Connector (CN5) Pin Pin Name Signal Type Signal Level 1 +5V PWR +5V 2 GND GND GND Signal Level 2.16 PCI-104 Connector (CN6) Standard PCI-104 Slot 2.
PC/104 Module PFM-CVS Rev. B 2 POWRR BUTTON# IN 3 External Buzzer(+) OUT 4 External Buzzer(-) OUT 5 HDD LED OUT 6 HDD LED# OUT 7 POWER LED OUT 8 POWER LED# OUT 9 RESET IN 10 RESET# IN 2.18 +12VSB Power Input Connector (CN9) Pin Pin Name Signal Type Signal Level 1 +12VSB PWR +12V 2 GND GND 2.
PC/104 Module PFM-CVS Rev. B 2.20 Digital I/O Connector (CN12) Pin Pin Name Signal type 1 GPI0 IN 2 GPI1 IN 3 GPI2 IN 4 GPI3 IN 5 GPO0 OUT 6 GPO1 OUT 7 GPO2 OUT 8 GPO3 OUT 9 +3.3V PWR 10 GND GND Signal Level +3.
PC/104 Module PFM-CVS Rev. B 6 GPO1 Bit 5 of 0xA00 7 GPO2 Bit 6 of 0xA00 8 GPO3 Bit 7 of 0xA00 2.21 Mini PCI Express/mSATA Connector (CN14) (Optional) Standard Mini PCI Express Connector (52Pins) Pin Pin Name Signal Type 1 WAKE# I/O 2 +3V3_MC PWR 3 Reserved 4 GND 5 Reserved 6 +1.5V PWR 7 MC_CLKREQ# I/O 8 Reserved 9 GND 10 Reserved 11 PCIE_MC_CKLN 12 Reserved Chapter 2 Quick Installation Guide 2-18 Signal Level +3.3V GND GND OUT +1.
PC/104 Module PFM-CVS Rev. B 13 PCIE_MC_CKLP OUT 14 Reserved 15 GND 16 Reserved 17 Reserved 18 GND 19 Reserved 20 W_DISABLE# 21 GND GND 22 BUF_PLTRST# IN 23 PCIE_RXN1 DIFF 24 +3V3_MC PWR 25 PCIE_RXP1 DIFF 26 GND GND 27 GND GND 28 +1.5V PWR 29 GND GND 30 SMBCLK_SBY I/O 31 PCIE_TXN1 DIFF 32 SMBDAT_SBY I/O 33 PCIE_TXP1 DIFF 34 GND GND 35 GND GND 36 USBP4- DIFF GND GND +3.3V +1.
PC/104 Module PFM-CVS Rev. B 37 GND GND 38 USBP4+ DIFF 39 +3V3_MC PWR 40 GND GND 41 +3V3_MC PWR 42 Reserved 43 GND 44 Reserved 45 Reserved 46 Reserved 47 Reserved 48 +1.5V 49 Reserved 50 GND 51 Reserved 52 +3V3_MC +3.3V +3.3V GND PWR +1.5V GND PWR +3.
PC/104 Module PFM-CVS Rev. B 2 +3V3_MC PWR 3 Reserved 4 GND 5 Reserved 6 +1.5V PWR 7 MC_CLKREQ# I/O 8 Reserved 9 GND 10 Reserved 11 PCIE_MC_CKLN 12 Reserved 13 PCIE_MC_CKLP 14 Reserved 15 GND 16 Reserved 17 Reserved 18 GND 19 Reserved 20 W_DISABLE# 21 GND GND 22 BUF_PLTRST# IN 23 SATA_RXP1 DIFF 24 +3V3_MC PWR 25 SATA_RXN1 DIFF +3.3V GND +1.5V GND OUT OUT GND GND +3.
PC/104 Module PFM-CVS Rev. B 26 GND GND 27 GND GND 28 +1.5V PWR 29 GND GND 30 SMBCLK_SBY I/O 31 SATA_TXN1 DIFF 32 SMBDAT_SBY I/O 33 SATA_TXP1 DIFF 34 GND GND 35 GND GND 36 USBP4- DIFF 37 GND GND 38 USBP4+ DIFF 39 +3V3_MC PWR 40 GND GND 41 +3V3_MC PWR 42 Reserved 43 NC 44 Reserved 45 Reserved 46 Reserved 47 Reserved I/O 48 +1.5V PWR 49 Reserved I/O Chapter 2 Quick Installation Guide 2-22 +1.5V +3.3V +3.3V I/O +1.
PC/104 Module PFM-CVS Rev. B 50 GND GND 51 Reserved I/O 52 +3V3_MC PWR +3.3V 2.22 Battery Connector (BT1) Pin Pin Name Signal Type Signal Level 1 RTCBAT PWR +3.3V 2 GND GND 2.
PC/104 Module PFM-CVS Rev. B 2.
PC/104 Module PFM-CVS Rev. B 2.25 COM1 RS-232 Connector (COM1) Pin Pin Name Signal Type Signal Level 1 DCD1 IN 2 DSR1 IN 3 RXD1 IN 4 RTS1 OUT ±9V 5 TXD1 OUT ±9V 6 CTS1 IN 7 DTR1 OUT 8 RI1 IN 9 GND GND ±9V 2.
PC/104 Module PFM-CVS Rev. B 3 RXD2 IN 4 RTS2 OUT ±9V 5 TXD2 OUT ±9V 6 CTS2 IN 7 DTR2 OUT 8 RI2 IN 9 GND GND Pin Pin Name Signal Type Signal Level 1 TX- OUT ±5V 2 N.C 3 RX+ 4 N.C 5 TX+ 6 N.C 7 RX- IN 8 +5V/+12V PWR 9 GND GND Pin Pin Name Signal Type Signal Level 1 B (Data-) I/O ±5V 2 N.C 3 N.
PC/104 Module 4 N.C 5 A (Data+) 6 N.C 7 N.C 8 9 PFM-CVS Rev. B I/O ±5V +5V/+12V PWR +5V/+12V GND GND 2.
PC/104 Module PFM-CVS Rev. B 2.28 COM4 RS-232 Connector (COM4) Pin Pin Name Signal Type Signal Level 1 DCD4 IN 2 DSR4 IN 3 RXD4 IN 4 RTS4 OUT ±9V 5 TXD4 OUT ±9V 6 CTS4 IN 7 DTR4 OUT 8 RI4 IN 9 GND GND ±9V 2.29 USB2.
PC/104 Module PFM-CVS Rev. B 4 GND GND 5 GND GND 2.30 USB2.0 Connector (USB2) Pin Pin Name Signal Type Signal Level 1 USB_VCC0 PWR +5V 2 USBP1- OUT 3 USBP1+ OUT 4 GND GND 5 GND GND 2.31 USB2.
PC/104 Module 5 GND PFM-CVS Rev. B GND 2.32 USB2.0 Connector (USB4) Pin Pin Name Signal Type Signal Level 1 USB_VCC1 PWR +5V 2 USBP3- OUT 3 USBP3+ OUT 4 GND GND 5 GND GND 2.
PC/104 Module PFM-CVS Rev. B 2.34 LAN Connector (LAN1) Pin Pin Name Signal Type 1 LAN1_TX1+ DIFF. 2 LAN1_TX1- DIFF. 3 LAN1_RX1+ DIFF. 4 LAN1_RX1- DIFF. 5 GND GND 6 GND GND 7 LAN1_TX2+ DIFF. 8 LAN1_TX2- DIFF. 9 LAN1_RX2+ DIFF 10 LAN1_RX2- DIFF Signal Level 2.
PC/104 Module PFM-CVS Rev. B 2.36 Audio Connector (CN15) Pin Pin Name Signal Type 1 MIC_L IN 2 MIC_R IN 3 GND GND 4 LIN_L IN 5 LIN_R IN 6 GND GND 7 LOUT_L OUT 8 GND GND 9 LOUT_R OUT 10 VCC PWR 2.
PC/104 Module PFM-CVS Rev.
PC/104 Module PFM-CVS Rev.
PC/104 Module PFM-CVS Rev.
PC/104 Module PFM-CVS Rev.B 3.1 System Test and Iinitialization These routines test and initialize board hardware. If the routines encounter an error during the tests, you will either hear a few short beeps or see an error message on the screen. There are two kinds of errors: fatal and non-fatal. The system can usually continue the boot up sequence with non-fatal errors. System configuration verification These routines check the current system configuration stored in the CMOS memory and BIOS NVRAM.
PC/104 Module PFM-CVS Rev.B complete unit when it finally runs down. 3.2 AMI BIOS Setup AMI BIOS ROM has a built-in Setup program that allows users to modify the basic system configuration. This type of information is stored in battery-backed CMOS RAM and BIOS NVRAM so that it retains the Setup information when the power is turned off. Entering Setup Power on the computer and press or immediately. This will allow you to enter Setup. Main Set the date, use tab to switch between date elements.
PC/104 Module PFM-CVS Rev.B Setup Menu Setup submenu: Main Options summary: (default setting) System Date Day MM:DD:YYYY Change the month, year and century. The ‘Day’ is changed automatically. System Time HH : MM : SS Change the clock of the system.
PC/104 Module PFM-CVS Rev.
PC/104 Module PFM-CVS Rev.
PC/104 Module PFM-CVS Rev.
PC/104 Module PFM-CVS Rev.
PC/104 Module PFM-CVS Rev.B Options summary: (default setting) Wake system with Fixed Disabled Time Enabled Enable or disable System wake on alarm event. Wake up time is setting by following settings. Wake up day 0-31 Select 0 for daily system wake up 1-31 for which day of the month that you would like the system to wake up Wake up hour 0-23 Wake up minute 0-59 Wake up second 0-59 Wake system with Disabled Dynamic Time Enabled Enable or disable System wake on alarm event.
PC/104 Module PFM-CVS Rev.
PC/104 Module PFM-CVS Rev.B IDE Configuration Options summary: (default setting) SATA Controller(s) Disabled Enabled En/Disable SATA controller Configure SATA as IDE AHCI Configure SATA controller operating as IDE/AHCI mode.
PC/104 Module PFM-CVS Rev.
PC/104 Module PFM-CVS Rev.B Options summary: (default setting) Legacy USB Support Enabled Disabled Auto Enables BIOS Support for Legacy USB Support. When enabled, USB can be functional in legacy environment like DOS. AUTO option disables legacy support if no USB devices are connected. DISABLE option will keep USB devices available only for EFI application Device Name Auto (Emulation Type) Floppy Forced FDD Hard Disk CD-ROM If Auto.
PC/104 Module PFM-CVS Rev.
PC/104 Module PFM-CVS Rev.B Serial Port 1 Configuration Options summary: (default setting) Serial Port Disabled Enabled En/Disable specified serial port. Change Settings Auto IO=3F8h; IRQ=4; IO=3F8h; IRQ=3,4; IO=2F8h; IRQ=3,4; Select a resource setting for Super IO device.
PC/104 Module PFM-CVS Rev.
PC/104 Module PFM-CVS Rev.B Options summary: (default setting) Serial Port Disabled Enabled En/Disable specified serial port. Change Settings Auto IO=2F8h; IRQ=3; IO=3F8h; IRQ=3,4; IO=2F8h; IRQ=3,4; Select a resource setting for Super IO device. Device Type RS232 RS422 RS485 Configure COM2 operated as RS232, RS422 or RS485.
PC/104 Module PFM-CVS Rev.B Serial Port 3 Configuration Options summary: (default setting) Serial Port Disabled Enabled En/Disable specified serial port. Change Settings Auto IO=3E8h; IRQ=11; IO=3E8h; IRQ=11; IO=2E8h; IRQ=11; Select a resource setting for Super IO device.
PC/104 Module PFM-CVS Rev.B Serial Port 4 Configuration Options summary: (default setting) Serial Port Disabled Enabled En/Disable specified serial port. Change Settings Auto IO=2E8h; IRQ=10; IO=3E8h; IRQ=10; IO=2E8h; IRQ=10; Select a resource setting for Super IO device.
PC/104 Module PFM-CVS Rev.
PC/104 Module PFM-CVS Rev.
PC/104 Module PFM-CVS Rev.
PC/104 Module PFM-CVS Rev.B Host Bridge Options summary: (default setting) Graphics Configuration Graphics Configuration Setting.
PC/104 Module PFM-CVS Rev.
PC/104 Module PFM-CVS Rev.B Options summary: (default setting) Fixed Graphics Memory 128MB Size 256MB Configure Fixed Graphics Memory Size IGFX - Boot Type VBIOS Default CRT LFP Select boot display device. Active LFP No LVDS LVDS En/Disable LVDS interface LCD Panel Type VBIOS Default 640x480 18bit 800x600 18bit 1024x768 18bit 1366x768 18bit 1280x800 18bit Select panel native resolution.
PC/104 Module PFM-CVS Rev.
PC/104 Module PFM-CVS Rev.
PC/104 Module PFM-CVS Rev.B Setup submenu: Boot Options summary: (default setting) Quiet Boot Disabled Enabled En/Disable showing boot logo.
PC/104 Module PFM-CVS Rev.B The order of boot priorities.
PC/104 Module PFM-CVS Rev.
PC/104 Module PFM-CVS Rev.B Options summary: (default setting) Administrator Password/ Not set User Password You can install a Supervisor password, and if you install a supervisor password, you can then install a user password. A user password does not provide access to many of the features in the Setup utility. Install the Password: Press Enter on this item, a dialog box appears which lets you enter a password. You can enter no more than six letters or numbers.
PC/104 Module PFM-CVS Rev.
PC/104 Module PFM-CVS Rev.B Options summary: (default setting) Save Changes and Reset Reset the system after saving the changes Discard Changes and Reset Reset system setup without saving any changes Restore Defaults Restore/Load Default values for all the setup options.
PC/104 Module PFM-CVS Rev.
PC/104 Module PFM-CVS Rev. B The PFM-CVS comes with a CD-ROM that contains all drivers and utilities that meet your needs. Follow the sequence below to install the drivers: Step 1 – Install Chipset Driver Step 2 – Install VGA Driver Step 3 – Install LAN Driver Step 4 – Install AUDIO Driver Step 5 – Install AHCI Driver Step 4 – Install Serial Port Driver (Optional) Please read instructions below for further detailed installations.
PC/104 Module PFM-CVS Rev. B 4.1 Installation: Insert the PFM-CVS Rev. B CD-ROM into the CD-ROM Drive. And install the drivers from Step 1 to Step 6 in order. Step 1 – Install Chipset Driver 1. Click on the Step 1 – Chipset folder and double click on the Setup.exe file 2. Follow the instructions that the window shows 3. The system will help you install the driver automatically Step 2 – Install VGA Driver For Windows® 7 1. Click on the STEP2-VGA folder and select the folder of WIN7_32 2.
PC/104 Module PFM-CVS Rev. B folder Double click on the IEMGDInstall.
PC/104 Module PFM-CVS Rev.
PC/104 Module PFM-CVS Rev. B If you want to update driver, please uninstall driver first. Uninstall IEMGD 1. Double click on the IEMGDInstall.exe 2. Follow the instructions that the window shows 3. The system will help you uninstall the driver automatically Step 3 – Install LAN Driver 1. Click on the STEP3 – LAN folder and select the OS your system is 2. Double click on the setup.exe file located in each OS folder 3. Follow the instructions that the window shows 4.
PC/104 Module PFM-CVS Rev. B Step 4 – Install AUDIO Driver 1. Click on the Step 4 – AUDIO folder and select the OS your system is 2. Double click on the .exe file located in each OS folder 3. Follow the instructions that the window shows 4. The system will help you install the driver automatically Step 5 – Install AHCI Driver For Windows 7: 1. Click on the STEP5 - AHCI folder and select the Win7 folder 2. Double click on the setup.
PC/104 Module Step 2: Setup OS Step 3: Press “F6” Chapter 4 Driver Installation 4 - 8 PFM-CVS Rev.
PC/104 Module PFM-CVS Rev.
PC/104 Module PFM-CVS Rev.
PC/104 Module PFM-CVS Rev. B Step 8: Install Rapid Storage Technology 1. Click on the Rapid Storage Technology folder 2. Double click on the setup.exe file 3. Follow the instructions that the window shows 4. The system will help you install the driver automatically Step 6 – Install Serial Port Driver (Optional) For Windows® XP 32-bit 1. Click on the STEP6 - Serial Port Driver (Optional) folder and select the OS folder of WINXP_32 2. Double click on the patch.bat file 3.
PC/104 Module PFM-CVS Rev. B 4. Check the driver installation in the device manager For Windows® 7 32-bit/ 64-bit 1.
PC/104 Module PFM-CVS Rev. B 2. Restart the operating system.
PC/104 Module PFM-CVS Rev. B 3. Click on the STEP6 - Serial Port Driver (Optional) folder and select the OS folder. 4. Right click on the patch.bat file and select Run as administrator 5. The system will help you install the driver automatically. 6. Check the driver installation in the device manager.
PC/104 Module PFM-CVS Rev.
PC/104 Module PFM-CVS Rev.
PC/104 Module PFM-CVS Rev. B A.1 Watchdog Timer Initial Program Table 1 : SuperIO relative register table Default Value Index 0x2E(Note1) Data 0x2F(Note2) Note SIO MB PnP Mode Index Register 0x2E or 0x4E SIO MB PnP Mode Data Register 0x2F or 0x4F Table 2 : Watchdog relative register table LDN Register BitNum Value Note Time of watchdog timer Timer Counter 0x07(Note3) 0xF6(Note4) (Note24) (0~255) This register is byte access Select time unit.
PC/104 Module PFM-CVS Rev.
PC/104 Module PFM-CVS Rev. B ************************************************************************************ VOID Main(){ // Procedure : AaeonWDTConfig // (byte)Timer : Time of WDT timer.(0x00~0xFF) // (boolean)Unit : Select time unit(0: second, 1: minute). AaeonWDTConfig(); // Procedure : AaeonWDTEnable // This procudure will enable the WDT counting.
PC/104 Module PFM-CVS Rev.
PC/104 Module PFM-CVS Rev.
PC/104 Module PFM-CVS Rev.
PC/104 Module B.1 I/O Address Map Appendix B I/O Information B-2 PFM-CVS Rev.
PC/104 Module PFM-CVS Rev.
PC/104 Module B.2 1st MB Memory Address Map Appendix B I/O Information B-4 PFM-CVS Rev.
PC/104 Module PFM-CVS Rev. B B.
PC/104 Module Appendix B I/O Information B-6 PFM-CVS Rev.
PC/104 Module PFM-CVS Rev.
PC/104 Module B.4 DMA Channel Assignments Appendix B I/O Information B-8 PFM-CVS Rev.
PC104 Board PFM-CVSB Rev.
PC104 Board PFM-CVSB Rev. B C.1 List of Mating Connectors and Cables The table notes mating connectors and available cables. Connector Function Label Mating Connector Vendor CN2 CN3 CN5 CN7 CN7 CN7 CN9 CN12 CN12 LAN1 VGA1 COM1 Model number Backlight CATCH H738-05 Brightness Control (Dummy) Internal HIROSE DF13-20S-1.
PC104 Board PFM-CVSB Rev. B COM2 COM3 COM4 USB1 USB2 USB3 USB4 CN15 CN18 COM2 RS232/422/ 485 Connector COM3 RS232 Connector COM4 RS232 Connector USB2.0 Connector USB2.0 Connector USB2.0 Connector USB2.
PC/104 Module PFM-CVS Rev.
PC/104 Module PFM-CVS Rev. B D.1 Electrical Specifications for I/O Ports I/O Backlight Brightness Control Connector Iternal LVDS Connector SATA Power Connector Digital I/O Connector Mini PCI Express/mSATA Connector CRT Connector COM2 RS232/422/485 Connector USB2.0 Connector USB2.0 Connector USB2.0 Connector USB2.0 Connector Reference Signal Name Rate Output CN2 VDD +5V/0.5 or +12V/0.5 CN3 VCC +3.3V/1A or +5V/1A CN5 +5V +5V/1A CN12 D0~D7 +3.3V/(Open drain) CN14 +3.3VSB +1.5V +3.3V/1.
PC/104 Module PFM-CVS Rev. B D.2 DIO Programming PFM-CVS Rev.B utilizes FINTEK 81866 chipset as its Digital I/O controller. Below are the procedures to complete its configuration and the AAEON initial watchdog timer program is also attached based on which you can develop customized program to fit your application. There are three steps to complete the configuration setup: (1) Enter the MB PnP Mode; (2) Modify the data of configuration registers; (3) Exit the MB PnP Mode.
PC/104 Module PFM-CVS Rev. B D.
PC/104 Module PFM-CVS Rev. B D.
PC/104 Module PFM-CVS Rev.
PC/104 Module PFM-CVS Rev.
PC/104 Module PFM-CVS Rev.
PC/104 Module PFM-CVS Rev.
PC/104 Module PFM-CVS Rev.
