User's Manual
Table Of Contents
- part i INTRODUCTION
- 1 GENERAL INFORMATION
- 1.1 Introduction
- 1.2 Product Type Numbers
- 1.3 Abbreviations
- 2 Physical organisation
- 2.1 Configurations
- 3 System Description
- 3.1 Introduction / Overview
- 3.2 Transmitters / Modulators
- 3.3 Monitors / Transmitter Control
- 3.4 Power Systems
- 3.5 Remote control system
- 3.6 Remote Maintenance Monitoring (RMM)
- 3.7 RMM Access
- 3.8 Storage Functions
- 3.9 Local Keyboard/Display Functions
- 3.10 Diagnostic functions
- 3.11 Document structure
- 4 Technical Specifications
- 4.1 Signal Requirements
- 4.2 Environmental characteristics
- 4.3 EMV-charakteristics
- 4.4 Mechanical characteristics
- 4.5 Power supply
- PART II instalLation
- 5 Mechanical Installation
- 5.1 Marker beacon Cabinet
- 5.2 Remote control
- 5.3 Antenna
- 6 Electrical installation
- 6.1 Marker beacon cabinet
- 6.2 Tower equipment
- 6.3 System Installation
- 7 Tests and adjustments
- 7.1 Preparations
- 7.2 Configuration settings
- 7.3 Adjustment points
- 7.4 Adjustments at installation
- 7.5 Other adjustments
- PART III Operation
- 8 Operation Main Cabinet
- 8.1 Power On/off
- 8.2 Local Control Operation
- 8.3 Local Keyboard/display Operation
- 8.3.1 The menu structure
- 8.3.2 Handling the different menu screens.
- 8.3.2.1 The menu screen
- 8.3.2.2 The readout screen
- 8.3.2.3 The toggle screens
- 8.3.2.4 Input/Store screen
- 8.3.2.5 The quick read screen
- 8.3.3 The access levels
- 8.3.3.1 Level 2
- 8.3.3.2 Level 3
- 8.3.3.3 Leaving the access levels
- 8.3.4 Function listing
- 8.3.4.1 Level 1
- 8.3.4.2 Level 2
- 8.3.4.3 Level 3
- 8.3.5 The menu tree
- 9 Remote Control And Slave Operation
- 9.1 Remote Control Operation
- 9.2 Slave Panel Operation
- 10 Operation of RMM
- 10.1 Introduction
- 10.2 The desktop area
- 10.3 Installation
- 10.4 Getting started
- 10.5 Users guide
- 10.5.1 The menus
- 10.5.2 The toolbar
- 10.5.3 Logging in and out and access levels
- 10.5.4 Station list
- 10.5.5 Modem set-up
- 10.5.6 Setting up connections
- 10.5.6.1 Setting up a Dial-up connection with an US Robotics Courier V34 modem
- 10.5.6.2 Setting up a Dial-Up connection with a Westermo modem
- 10.5.6.3 Setting up a leased-line connection with a US Robotics Courier V34 modem
- 10.5.6.4 Setting up a leased-line connection with a Westermo modem
- 10.5.7 Front panel
- 10.5.8 Monitor windows
- 10.5.9 Maintenance
- 10.5.9.1 Description of maintenance parameters
- 10.5.10 TX settings
- 10.5.11 Event list
- 10.5.12 Delays
- 10.5.13 Printing Reports
- 10.5.14 Loading and saving alarm/warning limits and delays
- 10.5.15 Tool options
- 10.5.15.1 The Data Logging Page
- 10.5.15.2 The NM7050 Options page
- 10.5.15.3 The NM7050 Main Warning mapping page
- 10.5.15.4 The NM7050 Communications page
- 10.5.16 Administration
- 11 Periodic maintenance
- 11.1 Reference Report
- 11.2 Monthly inspection
- 11.3 Annual inspection
- PART IV description
- 12 Detailed Description
- 12.1 Main Cabinet
- 12.1.1 TX 1373A Transmitter
- 12.1.1.1 General Description
- 12.1.1.2 Block diagram
- 12.1.1.3 Signals
- 12.1.1.4 Building blocks
- 12.1.2 MO1374 Monitor
- 12.1.2.1 General description
- 12.1.2.2 Block diagram
- 12.1.2.3 Signals
- 12.1.2.4 Building blocks
- 12.1.3 PS1375 Power Supply Module Description
- 12.1.3.1 General description
- 12.1.3.2 Block diagram
- 12.1.3.3 Signals
- 12.1.3.4 Functional description
- 12.1.4 CI1376/PB1378 Connection Interface Module Description
- 12.1.4.1 General description
- 12.1.4.2 Block diagram
- 12.1.4.3 Signals
- 12.1.4.4 Building Blocks
- 12.1.5 LC 1377 Local Control and Display/Keyboard Interface
- 12.1.5.1 General description
- 12.1.5.2 Block Diagram
- 12.1.5.3 Signals
- 12.1.5.4 Building Blocks
- 12.2 Tower Equipment
- 12.2.1 Remote Control Assembly
- 12.2.1.1 General Description
- 12.2.1.2 Block Diagram
- 12.2.1.3 Signals
- 12.2.1.4 Block Description
- 12.2.1.5 General Description
- 12.2.1.6 Block Diagram
- 12.2.1.7 Block Description
- 12.2.2 Remote Frame Assembly - RFA1353
- 12.2.3 SF1344 / SP 1394 Remote Slave Panel
- 12.2.3.1 General Description
- 12.2.3.2 Block Diagram
- 12.2.3.3 Signals
- 12.2.3.4 Block Description
- 12.3 Antenna
- 13 Circuit diagrams
- 14 Parts lists
- 15 Component Locations
- PART V APPENDIX
- A ANTENNA TYPE NM 3561 / NM 3562
- A.1 Antenna NM 3561 / NM 3562 For Ils Marker Beacon
- B MAINTENANCE PARAMETERS
- C CUSTOMERS INFORMATION
USER MANUAL
12-10
21464-5
NORMARC 7050
MARKER BEACON
Detailed Description ©1999 Navia Aviation AS
The mains input is fused and filtered before it is rectified and smoothed. The first DC/DC con-
verter generates 28VDC output which is filtered in the next block. The filter output serves as
both battery charger and input to the +20V, ±12V and +5V DC/DC converters. V28P is tem-
perature compensated to give 26.4V at 50°C, linearly increasing to 29.6V at -30°C.
The voltage (V28P) from either the AC/DC section or the battery is passed through an on/off
switch and separate fuses to the secondary DC/DC converters. Here +20V, ±12V and 5V are
created in one single and one triple output DC/DC converter. All outputs are lowpass filtered
in LC filters.
The or'ing diodes on the DC outputs makes parallel coupling possible. All RMM voltage mea-
surements are done prior to these diodes to make fault tracking possible. All RMM measure-
ments are multiplexed into A_PS_[P,N] by the AMUX_A[2:0] signals.
The RMM measurements are:
12.1.4 CI1376/PB1378 Connection Interface Module Description
12.1.4.1 General description
CI 1376 is the electrical backplane of NM 7050. The module has four functions:
• External connections interface with over voltage protection.
• Motherboard for all plug-in boards.
• Transmitter change over.
• Battery protection against deep discharge
Signal Measurement
I28P_MEAS
Total current in V28PP
IBATT_MEAS
Battery current in V28P
SIGN_I28P
Charge/discharge info to the
SIGN_IBATT
current measurements above
V*_MEAS
Voltage in corresponding V*