Specifications Sheet

TRADITIONAL KITCHEN SINKS PRODUCTS
INSTALLATION GUIDE
STOP ATTENTION (PLEASE READ)
This product requires a professional installation and custom
cabinetry. This product can not be installed in a normal sin base
cabinet without radical customization. A custom sink base is
recommended and can be ordered from your kitchen design
specialist.
Please observe all state and local building and plumbing codes.
NO TEMPLATE INCLUDED
A cutout template is not provided with apron sinks, due to the
varied cutout sizes that are possible based on your preferences.
Use the actual sink to determine the location of the cutout.
WARNING
Before installation, please inspect your product for any damage
that may have occurred during shipping. If the product was
damaged in the shipping process or your product needs to be
returned for another reason, it must be in the original packaging.
If the product is not returned with the original packaging you may
not be eligible for a refund of the purchase price. Return fees may
apply. Please contact your dealer for more information.
NEW INSTALLATION
When preparing for installation, it is recommended that you
consult with your countertop fabricator as to your installation
preference. When the fabricator is preparing the template for
installation, a ¼” overhang is recommended to provide a clean
transition from countertop to sink. The overhang will hide any sign
of the silicone adhesive.
INSTALLATION PREFERENCE
FLUSH MOUNT: The countertop is flush with the sink.
OVERHANG: The countertop is positioned over the sink bowl by a
set amount.
STEP 1
APRON CABINET PREP
Measure the actual size of the sink being installed to determine cabinet opening dimensions and
support frame location. The cabinet opening should equal the maximum dimensions of the sink
to ensure a minimum gap between the sink apron and the cabinet. Please be advised that the
apron has finished sides to allow for the apron to overhang the front fascial of the cabinet. The
overhang measurement is to customer preference.
To prepare the cabinet create a support frame inside the base that the sink will sit upon.
Use 2x4 solid wood studs to create the support frame. The frame should be strong enough to
hold up 300 lbs of weight once installed. The support frame should be positioned so that the top
of the sink rim is level and flush with the surface of the cabinet perimeter. Make sure that the
support frame leaves room for the drains, faucet, water lines and if there is one, a garbage disposal.
STEP 2
FINE MEASURING
After the installation location preferences have been determined. It will be necessary to custom scribe the apron cabinet sides or if needed, to
add wood filler strips.
BE ADVISED
SINK MOUNTING
Place a thin layer of sealant on the supporting frame where it will come in contact with the sink. Gently position the sink on the frame. Make
sure the sink sits level and sturdy on the frame. Check that the top surface of the sink is level and flush with the top of the cabinet rim. Be sure
that there is adequate space behind the sink for any faucet, accessories, and backsplash.
STEP 3
FABRICATION
Trace the cut-out opening on the countertop. Cut out the opening in the
countertop. Use and orbital sander to smooth the edge of the cut out area and
remove all saw marks. If cabinets are laminate, and exposed unfinished cut outs
must be sealed to prevent water damage. If using a countertop fabricator, they
will make an appropriate template. They will then fabricate and install the
countertop.
INSTALLATION
Clean the rim of the sink and the underside of the countertop where the sink will contact the rim of
the sink. Apply a generous bead of sealant around the sink rim.
COUNTERTOP
Gently position the countertop on the sink. Ensure that the sealant provides a complete seal between the countertop and sink. Wipe off any
excess sealant using a wet cloth. Apply extra sealant where there are any gaps.
Fireclay aprons have nominal dimensions. The apron will have up to a ¼ taper. When measuring, be aware that the apron rim measurement is longer than
the base.
Stainless steel aprons have nominal dimensions and have the risk of being scratched in the installation process.