User Guide

ManualsBrandsAbility ManualsElectronicsWCDMA and LTE wireless cellular module

111

112

113

114

115

116

117

118

119

120

Table Of Contents

APPLICABILITY TABLE
Contents
1. Introduction
- 1.1. Scope
- 1.2. Audience
- 1.3. Contact Information, Support
- 1.4. Symbol Conventions
- 1.5. Related Documents
2. general Product Description
- 2.1. Overview
- 2.2. Applications
- 2.3. General Functionality and Main Features
- 2.4. Block Diagram
- 2.5. Environmental Requirements
  - 2.5.1. Temperature Range
  - 2.5.2. RoHS Compliance
- 2.6. Operating Frequency Bands
  - 2.6.1. RF Bands per Regional Variant
  - 2.6.2. Reference Table of RF Bands Characteristics
- 2.7. RF Parameters
  - 2.7.1. Sensitivity
  - 2.7.2. Output power
- 2.8. Mechanical Specifications
  - 2.8.1. Dimensions
  - 2.8.2. Weight
3. Module Connections
- 3.1. Pin-out
- 3.2. Signals That Must Be Connected
- 3.3. LGA Pads Layout
- 3.4. Backward Compatibility to xE910 Family
4. Electrical Specifications
- 4.1. Absolute Maximum Ratings – Not Operational
- 4.2. Recommended Operating Conditions
- 4.3. Logic Level Specifications
5. Hardware Commands
- 5.1. Turning on the LE910Cx Module
- 5.2. Initialization and Activation State
- 1.1.
- 5.3. Turning off the LE910Cx Module
- 5.4. Powering OFF the Module
- 5.5. Fast Power Down
  - 5.5.1. Fast Shut Down by Hardware
  - 5.5.2. Fast Shut Down by Software
6. Power Supply
- 6.1. Power Supply Requirements
- 6.2. Power Consumption
- 6.3. General Design Rules
1.
7. Antenna(s)
- 7.1. GSM/WCDMA/TD-SCDMA/LTE Antenna Requirements
- 7.2. GSM/WCDMA/TD-SCDMA/LTE Antenna – PCB Line Guidelines
- 7.3. GSM/WCDMA/LTE Antenna – Installation Guidelines
- 7.4. Antenna Diversity Requirements
- 7.5. GNSS Antenna Requirements
8. Hardware Interfaces
- 8.1. USB Port
- 8.2. HSIC Interface (Optional)
- 8.3. SGMII Interface
  - 8.3.1. Ethernet Control interface
- 8.4. Serial Ports
- 8.5. Peripheral Ports
- 8.6. Audio Interface
  - 8.6.1. Digital Audio
- 8.7. General Purpose I/O
9. Miscellaneous Functions
- 9.1. Indication of Network Service Availability
- 9.2. Indication of Software Ready
- 9.3. RTC – Real Time Clock
- 9.4. VAUX Power Output
- 9.5. ADC Converter
  - 9.5.1. Description
  - 9.5.2. Using the ADC Converter
- 9.6. Using the Temperature Monitor Function
- 9.7. GNSS Characteristics
1.
1.
1.
1.
1.
10. Mounting the Module on your Board
- 10.1. General
- 10.2. Finishing & Dimensions
- 1.1.
- 10.3. Recommended Footprint for the Application
- 10.4. Stencil
- 10.5. PCB Pad Design
- 10.6. Recommendations for PCB Pad Dimensions (mm)
- 10.7. Solder Paste
  - 10.7.1. Solder Reflow
  - 10.7.2. Cleaning
11. Application Guide
- 11.1. Debug of the LE910Cx Module in Production
- 11.2. Bypass Capacitor on Power Supplies
- 11.3. SIM Interface
  - 11.3.1. SIM Schematic Example
- 11.4. EMC Recommendations
- 11.5. Download and Debug Port
  - 11.5.1. Fast Boot mode
  - 11.5.2. Recovery Boot Mode
12. Packing System
- 12.1. Packing System – Tray
- 12.2. Tape & Reel
- 12.3. Moisture Sensitivity
13. Conformity Assessment Issues
- 13.1. FCC/ISED Regulatory Notices
- 13.2. JTBL Regulatory Notices
- 13.3. NCC Regulatory Notices
- 13.4. ANATEL Regulatory Notices
- 1.1. Europe Approvals
- 13.5.
1.
1.
1.
14. PRODUCT AND SAFETY INFORMATION
- 14.1. Copyrights and Other Notices
  - 14.1.1. Copyrights
  - 14.1.2. Computer Software Copyrights
- 14.2. Usage and Disclosure Restrictions
- 14.3. Safety Recommendations
15. GLOSSARY
16. Document History

LE910Cx HW User Guide

1VV0301298 Rev. 34 Page 115 of 131

Not Subject to NDA

equipment generates, uses and can radiate radio frequency energy and, if not installed

and used in accordance with the instructions, may cause harmful interference to radio

communications. However, there is no guarantee that interference will not occur in a

particular installation. If this equipment does cause harmful interference to radio or

television reception, which can be determined by turning the equipment off and on, the

user is encouraged to try to correct the interference by one or more of the following

measures:

• Reorient or relocate the receiving antenna.

• Increase the separation between the equipment and receiver.

• Connect the equipment into an outlet on a circuit different from that to which the

receiver is connected.

• Consult the dealer or an experienced radio/TV technician for help.

Labelling Requirements for the Host device

The host device shall be properly labelled to identify the modules within the host device.

The certification label of the module shall be clearly visible at all times when installed in

the host device, otherwise the host device must be labelled to display the FCC ID and IC

of the module, preceded by the words "Contains transmitter module", or the word

"Contains", or similar wording expressing the same meaning, as follows:

LE910C1 NA

Contains FCC ID: RI7LE910C1NA

Contains IC: 5131A-LE910C1NA

LE910C1 NS

Contains FCC ID: RI7LE910C1NS

Contains IC: 5131A-LE910C1NS

LE910C1/C4 NF

Contains FCC ID: RI7LE910CXNF

Contains IC: 5131A-LE910CXNF

LE910C1 SV

Contains FCC ID: RI7LE910C1SV

LE910C1 SA

Contains FCC ID: RI7LE910C1SA

Contains IC: 5131A-LE910C1SA