INSTRUCTIONS MANUAL FEDERAL COMMUNICATIONS COMMISSION Fez. Moy (A pity INTERFERENCE STATEMENT This equipment has been tested and found to comply with the limits tor a Class B digital device, pursuant to Part 13 of the FCC Rules.
User’s Guide for CA2000 Installation Version 1.0 1999/10/04 Chapter 1 Introduction As Internet is getting popular, broadband revolution speed up the access speed. More people are willing to surf on Internet. But IP address is a limited resource. Using CA2000, users on local area network can access Internet simultaneously by sharing only single IP address. Chapter 2 Requirements & Environment Hardware requirements I. An well-connected Ethernet local area network 2.
Information from ISP If your ISP assign you IP address dynamically, then you have to prepare nothing. 1f your ISP assign you one IP address or a set of IP addresses, please list these IP addresses: For example: Your P address: 202.178.230.113 Neighbor IP address: 202.178.2311 DNS server: 202.178.225.1 Secondary DIS server: 202.178.244.207 Chapter 3 Start Installation Make sure you have all devices and cables well-connected as previous chapter described. And CA2000 is powered on. Configure your PC first 1.
WAN NIC Test von. O MAC Address: LAN NIC Test MAC Address: 00 40 0527 63 42 Internet SOAR is ready System starts up Welcome to SOAR 1.60 Administrator password : 4, Press ENTER key to enter Configure mode. You will see the command prompt SOAR> $type SET command to confrere CA2000. Press if you agree with the default value, or ESCAPE to escape. IP address for local [192.168.0.17 IP net mask for local [255.255.255.0} : Distribute con fig for PCs on LAN [Yes] : Distribute IP address pool start at [192.
Primary DNS server : [202.178.2251] Secondary DNS server : [202.178.244.207] Save this configuration and reboot device ? (Yes/No) : Y Save configuration and reboot Now you have completed the installation. You can try to run Internet applications for fast Internet access, Chapter 4 Command Set 1.
type new password (1 to 4 characters) : re-type new password (1 to 4 characters) : Password has been changed. 3.SHOW Display current configuration. Example: SOAR>show IP address for 10/100M LAN : [192.168.0.1] IP mask for 10/100M LAN : [255.255.255.0] Distribute con fig for PC son LAN : [Yes] ~~ #0 Distribute IP address pool start at : [192.168.0.2] CPD IP address pool numbers : [32] Obtain con fig automatically : [Yes] .. Con fig claimed IP address for 10M WAN : [202.178.231.
Press if you agree with the default value, or ESCAPE to escape. IP address for local [192.168.0.1] : IP net mask for local [255.255.255.0] : Distribute con fig for PCs on LAN (Yes/No) [Yes] : Distribute IP address pool start at [192.168.0.2] : CPD IP address pool numbers [32] : Obtain con fig automatically [Yes] : Device name (0 to 12 characters) : CA2000 Default gateway Router 202.178.231.1 Primary DNS server : 202.178.225.1 Secondary DNS server : 202.178.244.
6.RENEW If the “obtain configuration” function is enabled, this command will claim configuration parameters again. Those parameters are Global pert IP address, lease time, default gateway, primary DNS IP address, secondary DNS P address, and lease time, Example: SOAR>renew Request network configuration again !! 7.QUIT Escape from this configure mode . User has to input Management password to back to configure mode. Example: SOAR>quit Welcome to SOAR terminal program Administrator password © 8.
Chapter 5 Firmware Upload Hardware Requirements: 1. APC with at least one available COM port. 2. A pin-to-pin RS-232 cable( DTE-DCE ): one end is DB-9 male connector, the other end is whatever depends on your COM port. Software Requirements: 1. FWUPLOAD.EXE A DOS program for firmware upload. You can run it directly from Windows NT/95 also. 2. FIRMWARE The firmware image file. This file name MUST be exactly the same one. And it MUST be put together with FWUPLOAD.EXE.
