REGULATORY STATEMENTS Part, Class B This device complies with Part 15 of FCC rules. Operation is subject to the following two conditions: 1. This device may not cause harmful interface, and 2. This device must accept any interface received, including interface that may cause undesired operation. This equipment has been tested and found to comply with the limits for a Class B digital device, pursuant to Part 15 of the FCC Rules.
If this device is malfunctioning, it may also be causing harm to the telephone network; this device should be disconnected until the source of the problem can be determined and until repair has been made. If this is not done, the telephone company may temporarily disconnect service.
INTRODUCTIONS The 1M Phone Line Network & 10/100 Fast Ethernet PC Card brings the latest technology of instant connectivity to multiple PCs over a home's existing telephone lines. This PC Card is equipped with one JR-45 10/100 dual-speed Fast Ethernet port that enables any computer with a PCMCIA socket easily connected to a 10Mbps or 10/100Mbps network. The attached two standard JR-11 telephone ports let you network any notebook computer by connecting it to any standard phone line.
separate frequencies one for voice, one for high bandwidth net access such as DSL, and one for the network data. These frequencies can coexist on the same telephone line without impacting one another. The 1 Megabit-per-second (one million bits-per second) data rate is 18 times that of the fastest analog modems available, which run at 56Kbps. Even high speed modem, slid, and DISDAIN connections will perform at full speed on a home network.
* 10/100 Bps’ of Fast Ethernet data transfer » Doubled data transfer rate in Full duplex mode Supported Operating Systems * Auto Installation program ¢ DOS mode diagnostic program e NOS Drivers: Packet Driver for TCP/IP DOS ODI DIS 2.01 DOS Windows for Work groups 3.11 Windows NT Windows 95 All versions. Windows 98 all versions.
10M LED indicator: glows green when this adapter is linking to another 10 Bps Fast Ethernet. 100M LED indicator: glows green when this adapter is linking to another 100 Bps Fast Ethernet. HOME LED indicator: glows green when the adapter is connecting to another bps Phone Line Network adapter. ACT LED indicator: flashes orange when the Adapter is transmitting/receiving data via Ethernet or Home Phone line Networking.
HARDWARE INSTALLATION Before you begin, make sure you turn off all power to your computer. 1. Connect the 15-pin keyed connector to the PC Card until it locks firmly into place. 2. Locate the PCMCIA slot of your system. Align the 1M Phone Line Network + 10/100M Fast Ethernet PC Card with the 68-pin connector toward the PCMCIA slot. Push evenly and steadily until it is seated. Installing Ethernet Cabling a-1.
Installing Telephone Cabling b-1. Attach one end of the telephone wire to the Phone (JR-11) port of 1M Phone Line Network + 10/100M Fast Ethernet. Connect the other end of the cable into a telephone jack in your wall. The IM Phone Line Network + 10/100M Fast Ethernet PC Card is now connected to your PC. Perform the following procedures to install the Telephone cabling or Ethernet cabling.
SPECIFICATIONS Bus Type 16-bit PCMCIA PC Card Standard Network Standard » Homepage specification 1.1 = IEEE 802.3 for basset = [EEE 802.3u for 100BaseTX = CAT 3/CAT 5 UTP, 100ohm STP cable up to 328ft/100M Data Transfer Rate » Upton | Bps of Homepage data transfer * 10/100 Bps of LAN data transfer = Doubled data transfer rate in Ethernet Full duplex mode Supported Operating Systems . Auto Installation program + DOS mode diagnostic program e NOS Drivers: Packet Driver for TCP/IP DOS ODI DIS 2.
Phone Line: 5V DC, 158mA Certifications FCC Part 15 Class B FCC Part 68 CE Mark Physical Specifications LED: Link/Act, 10, 100, Phone Line Ports: = 10Mbps/100Mbps JR-45 port = 2 Standard Modular Telephone JR-11 Ports Dimensions: 3.4” x 2.1” x 0.2” Weight: 1.7 oz.