802.
Federal Communication Commission Interference Statement This equipment has been tested and found to comply with the limits for a Class B digital device, pursuant to Part 15 of the FCC Rules. These limits are designed to provide reasonable protection against harmful interference in a residential installation. This equipment generates uses and can radiate radio frequency energy and, if not installed and used in accordance with the instructions, may cause harmful interference to radio communications.
Table of Contents Package Contents & System Requirements ................................................................... 1 Features.............................................................................................................................. 1 SD WLAN Module Wireless Networks ............................................................................. 1 SD WLAN Card Network Scenarios......................................................................1 Installing the Driver ...........
PACKAGE CONTENTS & SYSTEM SYSTEM REQUIREMENTS 1. Manual (In CD-ROM ) 2. Drivers and configuration utilities on CD-ROM 3. Quick Install Guide 4. Product Device If you miss any of these items please contact your agent. FEATURES The 802.11abg Wireless SDIO Card is a wireless network card that complies with the IEEE 802.11abg standard on wireless LANs (Revision B). SDIO Card size as 40 (L) x 24 (W) x 2.1 (H) mm SDIO Interface Supports the IEEE802.
Home Networking With 802.11abg Wireless SDIO Card, wireless access to the Internet or other devices is at your fingertips. All you need to do is connect the 802.
INSTALLING THE DRIVER DRIVER Installation of the 802.11abg wireless SDIO card driver to the PDA via using Microsoft ActiveSync® 1. Connect your PDA to your computer and make sure Microsoft ActiveSync® has established a connection between the two devices. Note: Do not insert the 802.11abg Wireless SDIO Card into the card slot of your PDA until the Driver installation has been performed. Important Notice: The SDIO drivers are based on following CPU type: Intel PXA270 for Windows Mobile® 5.
Insert the included CD-ROM to your PC. The Wireless LAN Utility screen will appear, select the Install Driver (WM 5.0 or 6.0) to start driver installation.
2. Click “OK” to complete the driver installation. After finished driver installing, the installed successfully message will show on the PDA screen. Note: Do not insert the 802.11abg wireless SDIO card into the card slot of your PDA until the driver installation has been performed.
ACCESSING WLAN UTILITY Go to Start > Settings > Connections tab > select the Wi-Fi built-in WLAN utility. icon to access the Windows CE CONFIGURING WLAN UTILITY UTILITY Select an available AP or router from the list and tap Connect to make a connection. Network Adapters tab Configure Network Adapters My network card connects to: Tap Work or The Internet from the pull-down menu. Work: Connects to the network in your office. The Internet: Connects to your ISP at home.
If 802.11abg wireless SDIO card is tapped, the following screen will appear for you to configure: IP Address tab Use server-assigned IP address Tap Use server-assigned IP address to obtain an IP address automatically. The wireless router will act as a DHCP server. An IP address will be assigned from the wireless router.
Use specific IP address IP address: Enter the IP address (within the range of the wireless router’s IP address, for instance, if the IP address of the router which you would like to connect is 192.168.1.254, you may enter the IP address from 192.168.1.1 to 192.168.1.253, such as 192.168.1.123) Subnet mask: The subnet mask, for example, 255.255.255.0, must be the same as that set on your Ethernet network. Default gateway: Enter the IP address of your network’s gateway, such as 192.168.1.254.
REMOVING THE DRIVER If you would like to remove the driver from your PDA, please make a connection between the PDA and your computer via Microsoft ActiveSync® and then insert the CD-ROM into your PC. 1. Select the Install Driver (WM 5.0 or 6.0) to start to REMOVE the driver. 2. If you would like to re-install or upgrade the driver, please click “Yes”; if not, please click “No” to process removal.
3. Select the 802.11abg wireless SDIO card item, and then click “Remove” button to uninstall the program. 4. Click “OK” to confirm removing the application.
5. Click “OK” to complete the uninstallation.
