802.
Federal Communication Commission Interference Statement This equipment has been tested and found to comply with the limits for a Class B digital device, pursuant to Part 15 of the FCC Rules. These limits are designed to provide reasonable protection against harmful interference in a residential installation. This equipment generates uses and can radiate radio frequency energy and, if not installed and used in accordance with the instructions, may cause harmful interference to radio communications.
IMPORTANT NOTE: FCC Radiation Exposure Statement: This equipment complies with FCC radiation exposure limits set forth for an uncontrolled environment. This equipment should be installed and operated with minimum distance 20cm between the radiator & your body. This transmitter must not be co-located or operating in conjunction with any other antenna or transmitter. IEEE 802.11a or 802.11b/g operation of this product in the U.S.A. is firmware -limited to channels 1 through 11.
Table of Contents Package Contents & System Requirements ................................................................... 1 Features.............................................................................................................................. 1 SD WLAN Module Wireless Networks ............................................................................. 1 SD WLAN Module Network Scenarios ........................................................................................
PACKAGE CONTENTS & SYSTEM SYSTEM REQUIREMENTS 1. Manual (In CD-ROM ) 2. Drivers and configuration utilities on CD-ROM 3. Quick Install Guide 4. Product Device If you miss any of these items please contact your agent. FEATURES The 802.11abg Wireless SDIO Module is a wireless network Module that complies with the IEEE 802.11abg standard on wireless LANs (Revision B). SDIO Module size as 40 (L) x 24 (W) x 2.1 (H) mm. SDIO Interface Supports the IEEE802.11 a/b/g wireless.
Peer-to-Peer (Ad-hoc) Workgroup The Peer-to-Peer workgroup configuration enables you to quickly set up a small wireless workgroup, where the workgroup participants can exchange files using features like “Files and Printer Sharing” as supported by Microsoft® Networking. You can use this option to setup a temporary or Ad-hoc network in environments where no access points are available (for example in Small Office/Home Office “SOHO” environments).
INSTALLING THE DRIVER DRIVER Installation of the 802.11abg wireless SDIO Module driver to the PDA via using Microsoft ActiveSync® 1. Connect your PDA to your computer and make sure Microsoft ActiveSync® has established a connection between the two devices. Note: Do not insert the 802.11abg Wireless SDIO Module into the Module slot of your PDA until the Driver installation has been performed.
Important Notice: The SDIO drivers are based on following CPU type: Intel PXA270 for Windows Mobile® 5.0 Marvell PXA310 for Windows Mobile® 6.0 Please go to Start > Settings > System tab > select About CPU type. icon > Version tab to check the PDA If your PDA CPU is other type, please check with the agent of SDIO Module. Due to different PDA CPU type might cause incompatible between the driver and SDIO Module.
2. Insert the included CD-ROM to your PC. The Wireless LAN Utility screen will appear, select the Install Driver (WM 5.0 or 6.0) to start driver installation. 3. Click “OK” to complete the driver installation.
4. After finished driver installing, the installed successfully message will show on the PDA screen. Note: Do not insert the 802.11abg wireless SDIO Module into the Module slot of your PDA until the driver installation has been performed.
ACCESSING WLAN UTILITY Go to Start > Settings > Connections tab > select the Wi-Fi built-in WLAN utility. icon to access the Windows CE CONFIGURING WLAN UTILITY UTILITY Select an available AP or router from the list and tap Connect to make a connection. Wireless tab Configure Wireless Networks Select an available network device from the list and tap Connect.
Network Adapters tab Configure Network Adapters My network Module connects to: Tap Work or The Internet from the pull-down menu. Work: Connects to the network in your office. The Internet: Connects to your ISP at home. Tap an adapter to modify settings: Tap an adapter from the list to enter its configuration screen. Or select an adapter then tap Edit at the left-down corner of the screen to enter its configuration settings page. If 802.
Use specific IP address IP address: Enter the IP address (within the range of the wireless router’s IP address, for instance, if the IP address of the router which you would like to connect is 192.168.1.254, you may enter the IP address from 192.168.1.1 to 192.168.1.253, such as 192.168.1.123) Subnet mask: The subnet mask, for example, 255.255.255.0, must be the same as that set on your Ethernet network. Default gateway: Enter the IP address of your network’s gateway, such as 192.168.1.254.
REMOVING THE DRIVER If you would like to remove the driver from your PDA, please make a connection between the PDA and your computer via Microsoft ActiveSync® and then insert the CD-ROM into your PC. 1. Select the Install Driver (WM 5.0 or 6.0) to start to REMOVE the driver. 2. If you would like to re-install or upgrade the driver, please click “Yes”; if not, please click “No” to process removal.
3. Select the 802.11abg wireless SDIO Module item, and then click “Remove” button to uninstall the program. 4. Click “OK” to confirm removing the application.
5. Click “OK” to complete the uninstallation.
SPECIFICATIONS Standard IEEE 802.11a/b/g standards Chipset Atheros PA Chip FM7705 Host Interface SDIO 1.1 Operating Voltage 3.3V +/-5% Power Requirement Power consumption at 11a/g TX: 360 mA, RX: 185 mA Power consumption at 11b TX: 360 mA, RX: 185 mA Sleep mode: 995uA Antenna Type TWO HRS U.FL compatible connector on board Frequency Range 11b/g:2.412GHz-2.4835GHz 11a:4.9GHz-5.
Supported OS Microsoft Windows CE/Linux Receiver Sensitivity -72 dBm at 54Mpbs/11a, 10% PER -72 dBm at 54Mpbs/11g, 10% PER -84 dBm at 11Mpbs/11b, 8% PER Media Access Protocol CSMA/CA (Collision Avoidance) with ACK Physical Specifications Dimension: 40 (L) x 24 (W) x 2.
