60GHz WirelessHD Transceivers User Manual
Federal Communication Commission I nterference Statement This device complies with Part 15 of the FCC Rules. Operation is subject to the following two conditions: (1) this device may not cause harmful interference, and (2) this device must accept any interference received, including interference that may cause undesired operation. NOTE: This equipment has been tested and found to comply with the limits for a Class B digital device, pursuant to Part 15 of the FCC Rules.
Table of Contents CHAPTER 1: I NTRODUCTI ON................................................................................................................................... 1 OVERVI EW ....................................................................................................................................................................... 1 FEATURES ..................................................................................................................................................
Chapter 1: I ntroduction Overview For coming huge flat TV screen and high definition resolution, users like to set up the AV system in living room, but the cable placement always is a great harassment to the interior house. Also the HDMI cable is as expensive as the length as be. Users deserve to have a wireless cable replacement to match their high class AV systems.
Package Contents The following items should be included: z z z z 60GHz WirelessHD transmitter unit 60GHz WirelessHD receiver unit User manual Remote controller z Two-piece of HDMI cables z Two-piece of power adapters z Warranty leaflet If any of the above items are damaged or missing, please contact your dealer immediately.
Chapter 2: Hardw are I nstruction 60GHz WirelessHD Transmitter TX Front Panel Configuration TX LED Indicators LED Power Pairing Weak Color Green Blue Green Behavior Indication On The LED will illuminate when the power is connected and the power switch is turned on. Off The LED will be dark when the power switch is turned off. Blinking Unit in sleep mode. On The LED will illuminate to indicate which RX is being selected.
Strong Green On The LED will illuminate when the signal is strong. Off Signal weak I f 4 LEDs are b linking at same time, that means fan does n’t work, please turn off unit and send to serv ice station. TX Rear Panel Configuration Configuration DC-IN Connect the power adapter to the power DC-IN port. Switch Switch the button to turn on or off the power supply. HDMI Connect HDMI cable one end to this HDMI port and the other to the DVD player or computer HDMI port.
TX Side Panel Configuration TX Buttons Reset Press the “RESET” button to reset the system, the system will run through a full reset which takes approximately 5 seconds. CFG (Configure) This button is for upgrade system firmware. For further firmware upgrade process, please refer to Chapter 4: Software Upgrade. No function This button is fixed and no function here.
60GHz WirelessHD Receiver RX Front Panel Configuration RX LED Indicators LED Power Pairing Weak Strong Color Green Blue Green Green Behavior Indication On The LED will illuminate when the power is connected and the power switch is turned on. Off The LED will be dark when the power switch is turned off. Blinking Unit in sleep mode. On The LED will illuminate to indicate which TX is being selected. Off If the pairing LED is off, user has to re-select again or reset both devices.
RX Rear Panel Configuration Configuration DC-IN Connect the power adapter to the power DC-IN port. Switch Switch the button to turn on or off the power supply. HDMI Connect HDMI cable one end to this HDMI port and the other to the TV or computer HDMI port. RS232 D-Sub Connect the RS232 D-sub cable one end to this port, the other to the projector or TV RS232 D-sub port.
RX Buttons Reset Press the “RESET” button to reset the system, the system will run through a full reset which takes approximately 5 seconds. Input Switch ( Pending ) Press the RX unit "INPUT" button repeatedly to switch to desired source units (TX1/ TX2…) and the “PAIRING” LED will illuminate to indicate which source unit is being selected. CFG (Configure) This button is for upgrade system firmware. For further firmware upgrade process, please refer to Chapter 4: Software Upgrade.
Chapter 3: I nstallation Set Up Steps 1. Connect the 60GHz WirelessHD Transmitter with cables to media input sources, such as a computer or a DVD player.
2. And connect 60GHz WirelessHD Receiver with cables to media output sources, such as a monitor or a projector. Notice! Do not forget to turn on the pow er supplies of your monitor, projector or video device and sw itch them into corresponding settings. Such as, set your monitor sources into HDMI setting for media receiving.
3. Then, connect both power adapters of the 60GHz WirelessHD Transceivers to outlets. 4. Turn on the power of both 60GHz WirelessHD Transceivers. 5. After finished above set up steps, the 60GHz WirelessHD Transceivers will be ready to transmit media.
Chapter 4: Softw are Upgrade Softw are Application I nstallation The devices would allow user to upgrade firmware into new version. Please download the new firmware and application from the supported website. (Please fill in the website link.) Then, install the application on your computer or laptop by the following steps. 1. When this screen shows up, please click Next to install.
2. Select destination location, click Next to continue or click Browse to change the location. 3. Select start menu folder, click Next to continue or click Browse to change the folder. 4. Select to create a short cut on the desktop, and then click Next to process.
5. When following screen shows up, it is ready to install the application on your computer. Please click Install to setup. 6. The application installing is completed, click Finish to exit.
15
Start to Upgrade 1. Connect the RS232 D-Sub cable one end to device, the other to the computer or laptop RS232 D-Sub port.
2. After confirming the hardware connection, please execute the software application that installed. Communication Select the Com Port that connects the computer with RS232 D-Sub cable to the transceiver. 1. Find and open the RF firmware file by click the button, the browser will display to correct file path. RF Board Program (bin file) 2. Then, select the Product button to upgrade the program. 3. The upgrade status will show in the column below of the screen. 4.
then on the power to complete the firmware upgrading. Notice : User can upgrade the RF firmw are directly w ithout pressing CFG button. 1. Turn off the power supply first, and hold the CFG (Configure) button on the device turning on the power supply. Please remember to keep on holding the CFG (Configure) button for two seconds. The LEDs will not illuminate at this time. 2. Then, find and open the Host firmware file by click the button, the browser will display to correct file path.
separately. Chapter 5: Specifications Specifications Standards WirelessHD Frequency 60 GHz Input/ Output Interface HDMI Interface Antenna Type 36 Antenna Array (Integrate Ceramic) Range 10 meters indoors AV Port Transmitter : 1 Port (HDMI 1.3) Receiver : 1 Port (HDMI 1.3) Physical Specifications Weight: 324g±10g Dimension: 183 (L) x 80 (W) x 36 (H) mm Adapter Power AC 90-230V @ 60Hz input, DC 12V 1.
Operating Temperature: 0 ~ 50℃ ambient temperature Operating Environment (Total System) Except AC adaptor, it is only 0 ~ 40℃ Storage Temperature: -30 ~ 70℃ Operating Humidity: 10% to 90% (Non-condensing) Storage Humidity: 5% to 90% (Non-condensing) I/O Port RS232 Interface Video Format Resolution Format ( CEA-861 Code) Vertical Refresh Rate 24 Hz 50 Hz 640x480p (1) 720x576p (17/ 18) 25.175 MHz 25 MHz 27 MHz 1280x720p (19) 74.25 MHz 1280x720p (4) 1920x1080i (20) 74.176 MHz 74.25 MHz 74.
Multiples of Fs 32 kHz 44.1 kHz 48 kHz 88.2 kHz 96 kHz 176.4 kHz 19 128 4.096 5.645 6.144 11.290 12.288 22.579 2 256 8.192 11.290 12.288 22.579 24.576 45.158 4 512 16.384 22.579 24.576 45.158 49.152 Specific format support dependent on latest code release .
