ol FCC Certifications This equipment has been tested and found to comply with the limits for a Class B digital device, pursuant to Part 15 of the FCC Rules. These limits are designed to provide reasonable protection against harmful interference in a residential installation. This equipment generates, uses and can radiate radio frequency energy and, if not installed and used in accordance with the instructions, may cause harmful interference to radio communications.
Table of Content PARTS NAMES AND FUNCTIONS FACTORY DEFAULT SETTINGS. SetUPrarerorssosmsssrsssasssaossa Configuration ..uemwsommsosersos LOGIN. Basic SET ADVANCED SETUP. IP SETTING. PRIVACY . Perl omuaunanuwiom STATISTICS.
INTRODUCTION The Wireless 802.11b+g Access Point (AP) is an IEEE802.11g compliant access point. It not only provides a high transfer rate up to 54Mbps, which is almost five times faster than the already existing 11Mbps 802.11b products, but is also backward compatible with the Wireless b equipment. The AP provides 40/128/256 bit WEP encryption, WPA and IEEES02.1x, which ensures a high level of security to protects users” data and privacy.
Parts Names and Functions 1 Top Panel: (LED Indicators) I Pot Fe eon 3 Yorktown skirt. wi fm LED Status Indicator [Color | Solid Flashing 1 Power Green [Tums solid green when N/A. [power is applied to this device, 2 Err Status [Red [Tums solid red when the [When power on self-test device is not working failure occurs. properly. 3 Wireless |Green [Tums solid green when [Receiving/ Link/Act.
2. Rear Panel: Connection Ports A BC Port/button Functions A wpe Connects to the power adapter plug B LAN Connects to Ethernet C (Factory) [Press for § seconds to reboot this device and restore factory RESET settings. Performing the Factory Reset will erase all previously| entered device settings.
[Ele Sen | Wireless Accra 3s Point Device Name Wireless AP SAID Default value: 802.115SID Channel 5 WEP Default value: Disabled IP Address 192.168.1.
SETUP Note: Before your starting hardware connection, you are advised io find an appropriate location to place the Access Point. Usually, the best place for the Access Point is at the center of your wireless network, with line of straight to all your wireless stations. Also, remember to adjust the termagant; usually the antenna is placed higher, the performance will be better. | Withal Ether seminarian antiperspirant, » 3. Mauler, By Eoh.tr ether tastiness Susan Paint 1.
CONFIGURATION 1. Start your computer. Connect an Ethernet cable between your computer and the Wireless Access Point. 2. Make sure your wired station is set to the same subset as the Wireless Access Point, ie 192.168.1.10 3. Start your WEB browser. In the Address box, enter the following: | HTTP: //192, 168. 1, 252 GGG than. 192 1661.25 The configuration menu includes: Basic Setup, Advanced Setup, IP Setting, Privacy, Manage, Download, and Statistics.
Basic Setup The Setup page displays basic local and ELAN settings for the AP and enables yon to change the settings. FW Version The current version of the firmware installed in this device. SW Version The current version of the software installed in this device, Wireless : Enable/Disable AP Click to enable/disable the AP. Domain The AP’s domain determines the channel number. MAC addressable (The AP's MAC addressable. SUBSIDE displays the ID of current BSS, which uniquely identifies each BSS.
Channel The number of channels supported depends on the region of this Access Point. All stations communicating with the Access Point must use the same channel, After completing the settings, Click to save the settings.
Advanced Setup Tt is not recommended that settings in this page to be changed unless advanced users want to change to meet their wireless environment for optimal performance. Beacon Period Beacon Period is the amount of time between beacon transmissions. Before a Station enters power save mode, the station needs the beacon period to know when to wake up to receive the beacon (and learn whether there are buffered frames at the access point). The default value is 200.
its default setting of 4096. Should you encounter inconsistent data flow, only minor modifications of this value are recommended. Fragment Threshold Fragmentation mechanism is used for improving the efficiency when high traffic flows along in the wireless network, The value can be set from 256 to 4096. The default [value is 4096. Output Power Level You can choose the percentage of maximum power to meet your requirement. The default is Full.
LET] The IP Settings page displays the IP address for the AP. IP Address "This field can be modified only when CPD Client is disabled. If your system manager assigned you static IP settings, then vou will have to enter the information provided, Subset Mask Enter the information provided by your systems manager. Default Gateway Under the information provided by your system manager. [Save After completing settings, Click to save settings.
The Privacy page displays ELAN security settings. You can select WEP, 802.1x, or WPA to be the privacy mode for the AP. Click ©Enable Network Security or ©Disable Network Riv: ed Security to enable/disable Privacy. If you select to disable privacy function, there will be no need to change the rest of the settings. Authentication Type Open: If the type is selected, the associated station should set the same Authentication type as AP.
Tx Key You can select one of the Keys for Security. Key Value Please set the Key Value according to the WEP Cipher you select, If bits is selected, 10 Hex characters are needed, If tidbits is selected, 26 Hex characters are needed. If tidbits is selected, 58 Hex characters are needed. WEP Cipher You can choose one from tidbits is the highest WEP level among the three.
Group Key Interval Please enter the value to decide how long it should change the Group Keys. The default is 3600 seconds. WEP Keys . Enter the RADIUS Server’s TP Address provided by your ISP. Server IP Address Port Enter the RADIUS Server's port number provided by your ISP. The default is 1812. Secret Enter the secret phrase that the AP shares with the RADIUS Server. Save After completing the settings, Click to save the settings.
802.1x [WPA stations authenticate with RADIUS Server over 802.1x. Enter a period of time in Group Key Interval field to decide how long to change prong keys. PSK Hex ‘WPA stations share the per-shared key (PSK) with AP, you have to enter 64 characters for the key. Enter a period of time in Group Key Interval field to decide the interval to change group keys. PSK Passphrase ‘WPA stations share the per-shared key (PSK) with AP, 8-63 characters are needed for the key.
Port Enter the RADIUS Server's port number provided by your ISP. The default is 1812. Secret Enter the secret phrase shared between the AP and the RADIUS Server, After completing the settings, Click to save the settings. 7 Click to discard the data you have entered since last time you press [sad.
The management page displays information about stations that are currently associated with the AP. Click [Refresh to update the Associated Station Table. Mac Address Si ‘The Mac address of the station associated with the AP. State Current state between the associated station and the AP. SAID The SAID for the associated station. Active Rate [Current data transmitting/receiving rate.
station) Banned is selected in Allowed/Banned STA MAC Address. Press the button 10 add the Mac Address to the table if Allowed is selected in Allowed/Banned STA MAC Address, If Allowed/Banned STA MAC Address is disabled, there will [be no effect when pressing the button. Security Status The station’s security Status, Allowed/Banned STA MAC Address \ G Allowed O Banned O Allowed: only the stations shown in the table can associate ©Disable with the AP.
You can download the latest firmware (from your distributor) and upgrade the Wireless Point. Browse... Enter the new firmware’s path and file name (ie. image. Or, click the button, find and open the firmware file, Download Click [Download to start downloading the file.
The Statistics table shows the packets sent/received over the wireless and Ethernet LAN connection respectively. Click [Refresh] to update the data.
Wireless 802.11b+g Access Point The WAPITI is an IEEE802.11g compliant Access Point, which provides superior performance and interoperability within a mixed mode network (802.115, b+, mixed, 802.11g, and g+). The WAPITI is backwards compliant with all 802.11b and 802.11b+ wireless equipment, making it a seamless integrator for the most popular wireless networks.
SNR 4 ARRAS Specification Standards {IEEE 802.11 IEEE 802.3u base's-TX Fast Ethernet _ SUNSHINE 802.3 N-way Auto-Negotiation Channels & USA, Canada (FCC): 11 channels (2.412GHz~2 462GHz) Frequency Europe (CE). 13 channels Modulation Technique i Operation Mode B-entry MAC Address black/white list 64-entry associated stations list 02.1% WPA (WiFi Protected ACCESS) is ss transmission rate (1, 2, 8.
