802.11b Wireless CardBus PC Card User Guide Doc. No.
REGULATORY STATEMENTS FCC STATEMENT This model 802.11b Wireless CardBus PC Card (WB2000) must be installed and used in strict accordance with the manufacturer’s instructions as described in the user documentation that comes with the product. This device complies with Part 15 of FCC rules. Operation is subject to the following two conditions: 1) This device may not cause harmful interface, and 2) This device must accept any interface received, including interface that may cause undesired operation.
Warring: Changes or modifications not expressly approved by party responsible for compliance could void the user the user authority to operate the equipment. CAUTION: This transmitter must not be co-located or operating in conjunction with any other antenna or transmitter. Technical Support AboCom Systems, Inc. 300 1F, No.21, R&D Rd.II, SBIP, Hsin-Chu, Taiwan , R.O.C. Head office : Tel: 886-3-5789090 Fax:886-3-5789520 Technical Support: Tel: 0800-079-123 E-Mail: support@abocom.com.tw Website: www.abocom.
Table of Contents INTRODUCTION .............................................1 FEATURES.........................................................2 LED INDICATORS .............................................2 INSTALLATION THE UTILITY UNDER WINDOWS 98/ME/2000 ...................................3 UNINSTALL PROCEDURE UNDER WINDOWS 98/ME/2000 .....................................................7 Uninstall the Configuration Utility ......7 Uninstall the Device.............................9 HARDWARE INSTALLATION..
CONFIGURING THE NETWORK PROTOCOLS FOR WINDOWS XP.................................................24 CONFIGURATION AND MONITOR UTILITY FOR WINDOWS 98/ME/2000......27 STATUS ...........................................................29 STATISTICS .....................................................33 SITE SURVEY ..................................................34 ENCRYPTION ..................................................36 ADVANCED .....................................................39 VERSION .........
Introduction The 802.11b Wireless 32bit CardBus PC Card is a device that lets you connect your notebook to a wireless local area network (LAN). A wireless LAN is like a regular LAN, except that you can share information without looking for a place to plug in, and augment networks without installing or moving wires.
Features Complies with IEEE 802.11b standard for 2.4GHz Wireless LAN. Complies with CardBus standard. Supports PC Card hot swap and true Plug & Play. Works with all existing network infrastructure. Complies with specific wireless products and services Capable of up to 128-Bit WEP Encryption. Freedom to roam while staying connected. 11 Mbps High-Speed Transfer Rate. Rich diagnostic LED indicators with Integrated Antenna. Complies with Window 98/2000/ME/XP Lower power consumption.
Installation the Utility under Windows 98/ME/2000 Precaution for Windows 98, 2000, and ME users: You must install the Adapter's software before installation of the hardware. 1. Insert the Setup Utility CD-ROM into the CD-ROM drive and double click on Setup.exe to install the Configuration & Monitor Utility. 2. When the Welcome screen appears, click Next to continue.
3. The Choose Destination Location screen will show you the default destination chosen by the utility. Click Next to continue. 4. In Setup Type, choose Application and USB drivers and then click Next.
5. Follow the instruction to select the program folder. Click Next to continue. 6. In Start Copying Files, click Next to continue.
7. In Setup Status, the InstallShield Wizard will begin copying the files. 8. After the Configuration Utility has been successfully installed, select Yes, I want to restart my computer now, and then click Finish to restart.
Note: In case you need to uninstall the Utility or device, please refer to below section. Uninstall Procedure Windows 98/ME/2000 Under Uninstall the Configuration Utility 1. Go to Start LAN Programs Uninstall Monitor Utility. -7- 802.
2. Click OK to continue. 3. Click Finish to complete the uninstalled procedure.
Uninstall the Device Under Windows 98/ME 1. Go to Start → Settings → Control Panel → Network. 2. Select Wireless USB Adapter then click Remove. Click OK.
3. The system will prompt you to restart your computer. Click Yes. Under Windows 2000 1. Go to Start → Control Panel Add/Remove Hardware. 2. When the Welcome screen appears, click Next to continue.
3. In Choose a Hardware Task, select Uninstall/Unplug a device and click Next to continue. 4. In Choose a Removal Task, select Uninstall a device and click Next.
5. Check the Show hidden devices check box and locate the device in the device list. Select the device and click Next. 6. Select Yes, I want to uninstall this device and click Next.
7. Click Finish to complete the uninstalled procedure.
Hardware Installation Precaution for Windows 98, 2000, and ME users: Please do NOT install the hardware until the Application setup in Installation the Utility under Windows98/ME/2000 has been completed. 1. Plug the square end (Type B) of USB cable into the adapter's USB port. 2. Plug the rectangle end (Type A) of USB cable into the PC's USB port. After the device has been connected to your computer, Windows will detect the new hardware and then automatically copy all of the files needed for networking.
Installation of the USB Adapter for Windows XP 1. Once the device is well connected to your computer, Windows XP will automatically detect the new device. Click Install from a list… and click Next. 2. Insert the Setup Utility CD-ROM into the CD-ROM drive. Select Include this location in the search: and click Browse to provide the appropriate path (e.g. E:\Drivers\WinXP). Click Next.
3. Click Continue Anyway to proceed. 4. Click Finish to complete the Utility installation.
Uninstall Procedure Under Windows XP 1. Go to Start Control Panel Network Connections Wireless Network Connection Enabled Wireless USB Adapter Properties.
2. Click Configure to continue. 3. Click Uninstall to uninstall this device.
4. Click OK to complete procedure.
Network Connection Configuring the Network Protocols for Windows 98/ME/2000 1. Once the driver has been installed, you must make some changes to your network settings. Click Start Settings Control Panel Network. 2. Make sure that you have all the following components installed.
NetBEUI TCP/IP If any components are missing, click on the Add button to add them in. All the protocols and clients required and listed above are provided by Microsoft. 3. After clicking Add, highlight the component you need, click Add. 4. Highlight Microsoft, and then double click on the item you want to add.
5. For making your computer visible on the network, enable the File and Printer Sharing. 6. Click the Identification tab. Make up a name that is unique from the other computers' names on the network. Type the name of your workgroup, which should be the same used by all of the other PCs on the network. 7. Click the Access Control tab. Make sure that “Shared-level access control” is selected. If connecting to a Netware server, share level can be set to “User-level access control.
8. When finished, reboot your computer to activate the new device. 9. Once the computer has restarted and Windows has booted up, a Logon window will appear and require you to enter a username and password. Make up a username and password and click OK. Do not click the Cancel button, or you won’t be able to log onto the network. 10. Double-click the Network Neighbourhood icon on the windows desktop, and you should see the names of the other PCs on the network.
Configuring the Network Protocols for Windows XP Once the driver has been installed, you must check if some necessary network components are well setup in your computer. Click Start Control Panel Network Connections Wireless Network Connection Enabled Wireless USB Adapter Properties. Make sure that you have all the following components installed.
If any components are missing, click on the Install…button to select the clients/service/ protocols required. After selecting the component you need, click Add…to add it in. For making your computer visible on the network, enable the File and Printer Sharing.
When finished, you must restart your computer to complete installation.
Configuration and Monitor Utility for Windows 98/ME/2000 After installing the device successfully, go to Start Programs 802.11 Wireless LAN Configuration and Monitor Utility. The Wireless LAN Monitor Utility icon will appear in the taskbar every time the device is running. You can open it by double-clicking on this icon.
Icon Status Mode Access Point mode Icon Link Status Red. The station is not associated to an Access Point. Blue. The associates itself Access Point. Peer-to-Peer mode station to an Red. The color is red only when the card is during resetting and initialization procedure. Blue. The color is always blue, except when the card is during resetting and initialization procedure.
All settings are categorized into 6 tabs: Status Statistics Site Survey Encryption Advanced Version Status The Status tab will display the current status of the Wireless USB Adapter.
Item Description Operating Mode It displays the current operating mode. (Access Point or Peer-to -Peer). Channel It shows the selected channel that is currently used. (There are 14 channels available, depends on the country.) SSID The SSID is the unique name shared among all points in your wireless network. The name must be identical for all devices and points attempting to connect to the same network. It shows the current SSID setting of the Wireless USB Adapter.
Item Description Tx Rate It shows the current transfer rate. (1, 2, 5.5, or 11Mbps or Auto) Int Roaming It displays the current roaming status. (Disabled or Enabled) MAC Address It displays the MAC address of the Wireless USB Adapter. Status It displays the information about the status of the communication (the BSSID of the Access Point to which the card is associated).
- 32 -
Statistics This option shows you to view the available statistic information (Data packets, Management Packets and Rejected packets). Press the Reset button to renew or update this list of statistics.
Site Survey The Site Survey tab shows all the available Access Points and their features. Item Description BSSID A set of wireless stations is referred to as a Basic Service Set (BSS). Computers in a BSS must be configured with the same BSS ID. SSID The SSID is the unique name shared among all points in your wireless network. The name must be identical for all devices and points attempting to connect to the same network.
Item Description Signal It displays the signal strength of the connection between the Wireless USB Adapter and the Access Point it connects. Channel It shows the selected channel that is currently used. Encryption It displays the status of WEP Encryption. BSS It displays the type of Basic Service Set. Access Point: allows the Adapter to communicate with a wired network which employing an Access Point. Peer-to-Peer: allows PC-to-PC, station-to-station communication without employing an Access Point.
Encryption WEP (Wired Equivalent Privacy) encryption can be used to ensure the security of your wireless network. Item Description Encryption WEP is a data privacy mechanism based on a 64-bit/128-bit shared key algorithm. Under the drop-down box, you can choose to have WEP encryption Disabled, 64 Bit, or 128 Bit.
Key1/Key2/ Key3/Key4 This setting is the configuration key used in accessing the wireless network via WEP encryption. To generate an encryption key: 1. Select 64 Bit or 128 Bit. 2. Click "Key1" or "Key2" or "Key3" or "key4" item, then fill in the appropriate value/phrase. Default Key You can specify up to 4 different keys to decrypt wireless data. Select the Default key setting from the pull-down menu. Mode Two WEP modes are available as below: Mandatory and Optional.
is using "Open System" authentication, then the wireless adapter will need to be set to the same authentication type. Shared Key: Shared Key is when both the sender and the recipient share a secret key. Auto: Select Auto for the USB adapter to select the Authentication type automatically depending on the Access Point Authentication type. Submit Click Submit to save the changes. Exit Click Exit to exit the application.
Advanced You can change advanced configuration settings, such as the Preamble Type, Fragmentation Threshold and RTS/CTS Threshold.
Item Description Preamble Type A preamble is a signal used in wireless environment to synchronize the transmitting timing including Synchronization and Start frame delimiter. Long IF in a "noisy" network environment, the Preamble Type should be set to Long. Short The Short preamble is intended for applications where minimum overhead and maximum performance is desired. If in a "noisy" network environment, the performance would be decreased.
Power Save Check the box to allow the Adapter to go to sleep mode, during which data communication could be interrupted. Submit Click Submit to save the changes. Exit Click Exit to exit the application.
Version You can view basic information about the Utility like the Driver, Firmware and Application Version. Use the Exit button to exit the application.
Configuration for Windows XP 1. Go to Start Control Panel Network Connections. 2. In Network right-click the Connections Wireless window, Network Connections icon, and select Properties. Note: Double-click the Wireless Network Connection icon and you can see the status of the wireless PC Card as described below.
3. In Wireless Network Connection Properties window, select the Wireless Networks tab.
Use Windows to configure… Check the box to enable windows configuration. Available networks Displays all available networks. Configure Click the button to set up a new network or WEP configuration as illustrated as below.
Refresh Click the button to refresh and search for all available networks. Preferred networks From available network(s) listed above, you can select preferred one(s) in an order that you can arrange.
The marked one is the currently used network. Move up Move the selected network forward one position. Move down Move the selected network back one position Add… Click the button and the Wireless Network Properties window will appear. In the Network name field, enter your desired network name listed in the above Available networks box, and click OK. Note: The new settings will be active only after you click on OK in the Wireless Network Connection Properties window.
Highlight the network listed in the above Preferred networks box, and click the button to display its properties. Once network configuration is done, make sure to click OK. The new parameters will be saved and active only after doing so.
Specifications Standards IEEE 802.11b,Wi-Fi compliant Host Interface Antenna 32-bit CardBus LED Indicators Built-in Diversity Antenna LINK:Green,ON ACT:Orange,ON Frequency 2.412GHz-2.
Environment Specifications OperatingTemperature: 0~65℃ambient temperature Storage Temperature: -20~75 ℃ ambient temperature Operating humidity: 95% maximum (non-condensing) Storage humidity: 95% maximum (non-condensing) Supported OS Windows 98/ME/2000/XP EMC FCC Part 15 in US Certification EN300328 EN300826(EN301489-17) Europe Japan-Telec in Japan - 50 - and in
