802.
REGULATORY STATEMENTS FCC Certification The United States Federal Communication Commission (FCC) and the Canadian Department of Communications have established certain rules governing the use of electronic equipment. ※ The 802.11b/g USB Wireless LAN Card has been tested to the FCC exposure requirements (Specific Absorption Rate) measured value of 0.076 watts/kg.
interference in a residential installation. This equipment generates, uses and can radiate radio frequency energy, and if not installed and used in accordance with the instructions, may cause harmful interference to radio communications. However, there is no guarantee that interference will not occur in a particular installation.
Contact Person: Mr. Larry Table of Contents INTRODUCTION ...................................................................................................1 FEATURES ..............................................................................................................1 SOFTWARE INSTALLATION.............................................................................2 INSTALL THE DRIVER & UTILITY ............................................................................2 HARDWARE INSTALLATION....
INTRODUCTION The 802.11b+g Wireless LAN USB Adapter is designed for a USB type A port of a laptop or desktop computer for creating a wireless workstation. It is USB 2.0 compliant which connects to any available USB port on a notebook or desktop computer. The 802.11b+g Wireless LAN USB Adapter complies with IEEE 802.11g standard that offers a data rate up to 54Mbps in a wireless LAN environment. It is backward compliant with IEEE 802.11b specification.
SOFTWARE INSTALLATION Install the Driver & Utility Caution! Do not insert the wireless LAN adapter into your computer until the procedures in “ Install the Driver& Utility” have been performed. 1. Exit all Windows programs. Insert the included CD-ROM into your computer. The CD-ROM will run automatically. 2. When the Main Menu screen appears, click “ Driver & Utility Installation” to continue. 3. When the License Agreement screen appears, please read the contents and then click Yes to continue. 4.
Wireless Configuration Tool: Choose to use our configuration utility. Microsoft Zero Configuration Tool: Choose to use Windows XP’s built-in Zero Configuration Utility (ZCU). Click Next to continue. 5. There are two modes for you to choose in this screen, either choose WiFi mode or performance mode (TxBurst mode). This mode selection screen is set for the default mode shown in the utility screen, you can still change its mode later in the utility screen. Click Next to continue.
6. When the following screen appears, click Finish to complete the software installation.
HARDWARE INSTALLATION Note: Before you install the device to your computer, make sure you have installed the driver and utility as described in the previous section. Windows 98SE/2000/ME / XP 1. Locate your USB host and insert the USB Adapter. 2. Once the device has been inserted to your computer, Windows will detect the new hardware.
Verify To verify if the device exists in your computer and is enabled, go to Start Settings Control Panel System ( Hardware) Device Manager. Expand the Network Adapters category. If the 802.11b/g Mini Wireless LAN USB 2.0 Adapter is listed here, it means that your device is properly installed and enabled.
NETWORK CONNECTION Once the device driver is well installed, a network setting described in the following should be also established. In Windows 98SE/ME 1. 2. Go to Start Settings Control Panel Network. Make sure that all the required components are installed. If any components are missing, click on the Add button to add them in.
3. For making your computer visible on the network, enable the File and Print Sharing. 4. Click the Identification tab. Make up a name that is unique from the other computers' names on the network. Type the name of your workgroup, which should be the same used by all of the other PCs on the network.
5. Click the Access Control tab. Make sure that “Share-level access control” is selected. If connecting to a Netware server, share level can be set to “User-level access control.” 6. When finished, restart your computer to activate the new device.
In Windows 2000/XP 1. (In Windows 2000) Go to Start Connections Settings Control Panel Network and Dial-up Local Area Connection Properties. (In Windows XP) Go to Start Control Panel Network and Internet Connections Network Connection Wireless Network Connection Properties.
2. Make sure that all the required components are installed. 3. If any components are missing, click on the Install… button to select the Client/Service/Protocol required. After selecting the component you need, click Add… to add it in. 4. For making your computer visible on the network, make sure you have installed File and Printer Sharing for Microsoft Networks.
IP Address Note: When assigning IP Addresses to the computers on the network, remember to have the IP address for each computer set on the same subnet mask. If your Broadband Router use DHCP technology, however, it won’t be necessary for you to assign Static IP Address for your computer. 1. To configure a dynamic IP address (i.e. if your broadband Router has the DHCP technology), check the Obtain an IP Address Automatically option. 2.
Configuration Utility After the Wireless adapter has been successfully installed, users can use the included Configuration Utility to set their preference. Go to StartJ ProgramJWireless LAN USB 2.0 AdapterJ Wireless Utility You can also open the Configuration Utility by clicking the icon.
Profile The Profile Manager enables you to create, edit and delete the profiles that the station uses to connect to WLAN networks, to activate and de-activate profiles, and to raise and lower a profiles’s priority. Profile Tab Profile Name You may enter a distinctive name of profile in this column. The default is PROF# (# 1, #2, #3....) SSID The SSID is the unique name shared among all points in your wireless network. Channel Shows the selected channel that is currently in use.
Edit Click to edit a profile. Activate Click to make a connection between devices. OK Click to exit this page. Link Status The link status page displays the detail information of current connection. Link Status Tab Status Shows the current connection status. If there is no connection existing, it will show Disconnected. Extra Info Shows the link status. Channel Shows the current channel in use. Link Speed Shows the current transmitting rate and receiving rate.
Link Quality Shows the connection quality based on signal strength and TX/RX packet error rate. Signal Strength Shows the Receiving signal strength, you can choose to display as percentage or dBm format. Noise Level Shows the noise signal strength. OK Click to exit this page. Site Survey The Site Survey page displays the information of surrounding APs from last scan result. List information including SSID, BSSID, Signal, Channel, Encryption algorithm, and Network type.
Channel Shows the currently used channel. Encryption Shows the encryption type currently in use. Valid value includes WEP, TKIP, AES, and Not Use. Authentication Authentication mode used within the network, including Unknown, WPA-PSK, WPA2-PSK, WPA and WPA2. Network Type Network type in use, Infrastructure for BSS, Ad-Hoc for IBSS network. Rescan Click to refresh the site survey list. Connect Select an item on the list and then click to make a connection.
Transmit Statistics Frames Transmitted Successfully Frames successfully sent. Frames Transmitted Successfully Without Retry Frames successfully sent without any retry. Frames Transmitted Successfully After Retry Frames successfully sent with one or more reties. Frames Fail To Receive ACK After All Retries Frames failed transmit after hitting retry limit.
Out-of-Resource Duplicate Frames Received Duplicate received frames. Reset Counter Reset counters to zero. Advanced This Advanced page provides advanced settings. Advanced Tab Wireless mode Select wireless mode. 802.11b only and 802.11 b/g mixed mode are supported Ad hoc wireless mode Select ad hoc wireless mode. 802.11b only and 802.11 b/g mixed mode are supported. 11B/G Protection Choose Auto, On or Off from the pull-down menu.
TX Rate Select the Tx rate from the pull-sown menu. The default is auto. Tx Burst Check to enable the burst mode. Fast Roaming at Check to set the roaming interval. Select Your Country Region Code Select your country region code from the pull-down menu. CCX2.0: support Cisco Compatible Extensions function: Check to enable the CCX2.0 function. • LEAP turn on CCKM • Enable Radio Measurement: can channel measurement every 0~2000 milliseconds. • Enable QOS: enable Quality of Service.
UNINSTALLATION In case you need to uninstall the Utility and driver, please refer to below steps. (As you uninstall the utility, the driver will be uninstalled as well.) 1. Go to Start Programs Uninstall - Utility. Wireless LAN USB 2.0 Adapter 2. Click OK to continue. 3. Click Finish to complete the uninstalled procedure.
