0/100Mbps Dual Speeds Fast Ethernet PC Card Ethernet Adapter Quick Installation Guide
HARDWARE INSTALLATION This chapter describes how to install the dual speeds Fast Ethernet PC Card in your notebook computer and connect it to network. The PC Card could be connected to either 100Mbps Fast Ethernet or 10Mbps Ethernet over unshielded twisted pair (UTP) cable. The PC Card has the ability automatic sensing and operating on either speed without manual reconfiguration. Please refer to Software Installation on how to install network drivers using menu driven installation utility.
Connecting and Removing the Cable of Media Coupler to the PC Card Grasp the PC Card 15-pins connector at the end of the media coupler with the pointing triangle facing upward. Gently insert it into the mating connector on the PC Card until it clicks in place at both sides. Attention should be paid when removing the 15-pins connector. Please press the both sides of the connectors before dragging out of the PC Card.
should be used to connect between media coupler and 100Mbps hub or switch. symbol 108 \f "Monotype Sorts" \s 6O For operation in the 10Mbps (10Base-T) Ethernet network, Category 3, 4 or 5 unshielded twisted pair (UTP) cable could be used to connect between the media coupler and a 10Mbps hub or switch.
SOFTWARE INSTALLATION Plug the driver diskette into the floppy drive and set the current drive to the floppy drive. Then run INSTALL to install the real mode drivers such as ODI or NDIS 2.x or Packet Drivers into the target disk. Novell Netware There are two methods to install the Netware client ODI driver, the menu installation and Netware 3.12 or 4.x Client installation. Menu Installation 1.Run INSTALL.EXE from the root directory of driver diskette. 2.Select Netware 3.x and 4.
3.If current settings are acceptable, select Start Installation and go to step 5. Otherwise, select Modify Parameters to make settings changed 4.Move cursor to focus on the setting you want to make change and press ” to select a fit value. When the configurations are set completely, press on the OK” field to exit the screen and go back to step 3. 5.Installation program starts copying related files from diskette to the destination directory and modifies AUTOEXEC.BAT and NET.
2.Using a text editor to edit the NET.CFG for setting the default frame type. In the Netware server the frame type is set to 802.3 for NW3.11 and 802.2 for NW3.12 and NW4.x The frame type must be set to the same with the server or the client couldnsymbol 146 \f "Parisian BT" \s 10’}t login to the server. 3.Follow Novell's instructions on using ODI programs. You can substitute the LE100ODI.COM whenever a reference is made to the Hardware Specific Module. 4.
-Get the 4 Client disks from the network administrator, or -Run the \NWCLIENT\INSTALL.EXE in a previous Installation 2.A message appears on the screen asking you whether or not you want the program to perform modifications on your AUTOEXEC.BAT and CONFIG.SYS files. 3.Answer "Yes". The program then modifies your AUTOEXEC.BAT and CONFIG.SYS files accordingly and creates backup copies. 4.The following message appears: -Install support for MS Windows? (Y/N): 5.Answer accordingly and provide a path if necessary.
10.Go to the Insert the Driver Disk dialog box and specify the path where the ODI driver and INS files reside. For example: C:\ODI.DOS. 11.Press Enter and select the target ODI driver. 12.Specify the driver's optional settings. 13.Press F10 to save to new configuration. 14.Highlight "Install press here" and press to install. The program copies the necessary files for NetWare Client. Continue the installation procedure to completion. Upon completion, a new NET.
--Card Enabler SET NWLANGUAGE=ENGLISH --Set NetWare 4.X to English language LSL --Link Support Layer Module provided by Novell LE100ODI --Hardware Specific Module IPXODI --IPX Protocol Stack provided by Novell VLM --DOS Support Module provided by Novell F: --Change to connected device LOGIN xxx --Login to file server as user xxx Module 17.Run STARTNET to access the Novell network. MS LAN Manager 1.View the README.TXT on the installation diskette in the \NDIS2 directory.
3.Select Microsoft LAN Manager item on the menu screen. 4.If current settings are acceptable, select Start Installation” and go to step 6. Otherwise, select Modify Parameters” to make setting changed. 5.Move cursor to each field you want to make a change and press to select a fit value. When the configuration are set completely, press on the OK field to exit the screen and go back to step 4. 6.
Example of PROTOCOL.INI: used by LAN Manager [PROTMAN] DRIVERNAME = PROTMAN$ DYNAMIC = YES PRIORITY = NETBEUI [NETBEUI_XIF] Drivername = netbeui$ SESSIONS = 6 NCBS = 12 BINDINGS = "LE100NDS_NIF" LANABASE = 0 [LE100NDS_NIF] ; protocol.ini session for LAN driver.
DRIVERNAME = LE100NDS$ Packet Driver 1.Run INSTALL.EXE from root directory of driver diskette. 2.Select Packet Driver item on the menu screen. 3.If current settings are acceptable, select Start Installation and go to step 5. Otherwise, select Modify Parameters” to make setting changed. 4.Move cursor to focus on the field you want to make a change and press to select a fit value. When the configuration are set completely, press on the OK” field to exit the screen and go back to step 3. 5.
3.In Networks dialog box, check Install Microsoft Windows Network and Others, thereafter select Novell NetWare (Workstation Shell, 3.X) or Novell NetWare (Workstation 4.0 and above) and press OK to enter the screen of PXODI.COM and LSL.COM” 4.Press OK to go back the Network Setup“ screen. 5.Click on Drivers...” button to select network driver. 6.In Network Drivers dialog box, press Add Adapter...” button to enter Add Network Adapter dialog box. Select Unlisted or Updated Network Adapter and press OK. 7.
12.If current settings are acceptable, select Start Installation” and go to step 13. Otherwise, select Modify Parameters” to make settings changed. 13.Move cursor to focus on the setting you want to make a change and press to select a fit value. When the configuration is set completely, press on the OK field to exit the screen and go back to step 11. 14.Select Novell Netware Server as the network server you will attach to and press key. 15.
3.Open My Computer 4.Open Control Panel 5.Run the Network 6.Select Adapters page 7.Press Add to add network adapter 8.Press Have Disk button 9.Insert the driver disk into drive A: 10.Specify the path to ” A:\ and press OK 11.A dialog box will appear to adjust the driver's settings. The resources assignment to the adapter must be unique in the system. 12.Press OK when all settings are completed. 13.Press Close to complete network setting Windows 95 Installation 1.
2.Insert the PC Card into the slot. In New Hardware Found dialog box, select Driver from disk provided by hardware manufacturer”. 3.Please input the path, A:\ and insert driver diskette. The driver will be installed and you may be asked for the original Windows 95 CD/disks. 4.For the first time installation, please click Network icon in Control Panel to add Protocols, Client and Service if you needed 5.Reboot the machine and the card will be fully functional. Artisoft Lantastic 6.0 Installation 1.
2.Run INSTALL.EXE from root directory of driver diskette. 3.Select LANTASTIC 6.0 in Network Operating System screen. 4.If current settings are acceptable, select Start Installation” and go to step 6. Otherwise, select Modify Parameters” to make settings changed. 5.Move cursor to focus on each field you want to make a change and press ” to select a fit value. When the configuration is set completely, press ” on the OK field to exit the screen and go back the step 4. 6.
properly. If the PCMCIA Service of OS/2 Warp has been enabled already, please jump to portion B for driver installation otherwise please follow the instructions in the following to install the PCMCIA Service. A. Enable PCMCIA Service of OS/2 Warp 1.In the OS/2 Desktop group, double-click on the OS/2 System icon. 2.Double-click on the System Setup icon. 3.Double-click on the Selective Install icon. 4.Select the PCMCIA Support button. 5.Select PCMCIA system. For example: select IBM ThinkPad 750 6.Click OK”.
1.In the OS/2 Desktop group, double-click on the MPTS icon. 2.Click on the Configure button. 3.Select the LAN adapters and protocols option. 4.Click on the Configure button. 5.Select the Other adapters ...” option. 6.Insert the driver diskette and type the driver path: A:\OS2\NDIS2 Click on the OK button. 7.Select PCMCIA Ethernet Adapter, and then click on the Add button. 8.Select IBM OS/2 NETBIOS, and then click on the Add button. 9.Click OK”. 10.Click Close”. 11.Click Exit”. 12.
