ISDN TA PCI Card From Quick Setup to Internet Access
Class B CE Mark Warning This is a Class B product.
Quick Installation for Windows 98/ME/2000/XP VCOMM (PPP) -- Basic Internet Precautions: 1. This quick installation guide aims at helping you to setup the ISDN TA PCI Card and go to the Internet in VCOMM mode with ease and efficiency. For NDIS and CAPI modes, refer to the user manual for details. 2. Before you proceed the following steps, make sure no old driver suites exist in your computer. Uninstall any old driver suites that already exist, for these could hamper your computer system.
9. To verify whether the Network device exists in your computer and is enabled, go to My ComputerÆControl PanelÆSystem. Click the Device Manager tab. If the Intelligent PCI ISDN TA (ISDN) device, Modems, Multifunction adapters and Network adapters are found, it means that your Network device is well installed and enabled. If not, consult your computer dealer for technical support. Installing the Applications 1. Go to My Computer. 2. Select the drive whichever contains the device driver.
using compact disc, select the CD-ROM drive and double-click on folder PCI\WIN98ME when in Windows 98/ME, or PCI\WIN2KXP for Windows 2000/XP. 3. Double-click Setup.exe. Follow the on-screen instructions to proceed. Windows 2000/XP Uninstall Removing the Device Driver 1. Go to My ComputerÆControl PanelÆSystem. 2. From the System window, click the Hardware tab. 3. From the Hardware tab, double click the Device Manager button. 4. From the Device Manager window, click Multifunction adapters to expand.
Removing the Applications 1. Go to My ComputerÆControl Panel. 2. From the Control Panel window, double click the Add/Remove Programs icon. 3. Choose Configuration Utility for Windows 2000. Click Change/Remove button and click OK. The applications for this device will be removed automatically. 4. Remove the ISDN TA PCI Card from your computer. Making a New Connection 1. Go to My Computer. 2. Select Dial-Up Networking. Double-click Make a New Connection, a dialog box will appear as shown below. 3.
6. From the Dial-Up Networking window right-click your newly created connection. Select Properties. On the General tab, cancel the selection of “Use area code and Dialing Properties” and click OK. 7. From the Start menu, select Programs. Select Configuration Utility. Click Config. A dialog box will prompt you to change the settings to fit your needs.
. 9. Select the proper switch type corresponding to your need. Switch Type varies between countries. Although you have the option of “Automatic” as a selection, it is highly recommended that you choose a specific selection to reduce the chance of incompatibility. Typically the selections are as follows: Area Switch Type Canada & United States Northern Telecom & NI-1 Japan INS Net 64 Taiwan DSS1 (ETSI) Europe DSS1 (ETSI) Enter in the ISDN phone numbers and the Service Profile Identifier.
Quick Installation for Windows NT NDIS (PPP) -- Basic Internet Precautions: 1. This quick installation guide aims at helping you to setup the ISDN TA PCI Card and go to the Internet in NDIS mode with ease and efficiency. For CAPI mode, please refer to the user manual for details. 2. Before you proceed the following steps, make sure no old driver suites exist in your computer. Uninstall any old driver suites that already exist, for these could hamper your computer system. Installing the Device Driver 1.
3. Click Have Disk… and click OK to continue. 4. If you are using disks to install the device driver, insert the device driver disk into the floppy disk drive of your system and enter the drive name, for example, A:, to continue. Or if you are using compact disc to install, insert the compact disc into the CD-ROM drive of your system and enter the CD-ROM drive letter followed by PCI\WINNT\DRIVERS, and click OK to continue. 5. When the Select OEM Option dialog box appears, click OK to continue.
6. When the following dialog box appears, enter the required data appropriately. 7. Click OK to continue. The installation program will proceed automatically. 8. When finished, a Setup Message will prompt you to invoke Remote Access Services (RAS) setup. Click OK to continue. 9. When the Network dialog box appears, select the Services tab.
10. Select Remote Access Service. Click Properties. The following figure will appear. Select Add... When the Add RAS Device dialog box appears, select ISDN1 – ISDN_TA and click OK. Click Add... again to add ISDN2-ISDN_TA. When completed, click Continue. The Network dialog box will appear again. Click Close. The installation program will continue automatically. When finished, Windows will prompt you to restart your computer. Click Yes to continue.
- 13 -
Installing the Applications 1. Insert the application software disk or compact disc into your computer. 2. Go to the Start menu. Click Run. 3. If you are using compact disc to install the application software, enter the CD-ROM drive letter followed by winnt\ntap\setup. Or if you are using disk, enter a: setup. The Configuration Utility installation program will proceed automatically. 4. Follow the on-screen instructions to continue. When finished, Windows will prompt you to restart your computer.
Making a New Connection 1. Go to My Computer. Select Dial-Up Networking. 2. Click New... to name the phonebook appropriately. 3. Shift to the next tab to enter the required data.
4. When finished, click OK. Select Dial to continue. 5. When the Connect to ISDN dialog appears, you are connected to the Internet.
