Absco Premier Garden Shed ABSCO PREMIER SHED Assembly Instructions MODEL: 30302GK-PTX Australian Made 10’ W x 10’ D x 7’ H Model: J30302G AU:(866) 1800 029 701 +1 788 3046 N Z: 0800 466 444 FRONT: 9' 10 7⁄64" SIDE: 9' 10 7⁄64" HEIGHT: 6' 10 43⁄64" admin@absco.com.au www.abscosheds.com.
ABSCO PREMIER SHED PremierMODEL: Garden30302GK-PTX Shed - Model: J30232G Australian Made 10’ W x 10’ D x 7’ H GENERAL INSTRUCTIONS Before commencing any assembly, read through these instructions in detail to gain a thorough understanding of assembly methods and associated details. Unpack the carton and carefully identify and check off all the parts against the parts described and illustrated on pages three and four. SITE PREPARATION The site for the shed must be level.
ABSCO PREMIER SHED MODEL: 30302GK-PTX 10’ W x 10’ D x 7’ H Australian Made COMPONENTS PACKING LIST - CHECK OFF ALL COMPONENTS QTY COMPONENT DESCRIPTION 2 STEEL SHEET 5' 10 9⁄32" Long 2' 6 7⁄16" Wide 30A 2 STEEL SHEET 5' 10 9⁄32" Long 2' 6 7⁄16" Wide 31A 2 STEEL SHEET 5' 10 9⁄32" Long 2' 3 63⁄64" Wide 34A 1 2 1 2 STEEL SHEET 6' 3 25⁄64" Long 2' 6 7⁄16" Wide 36L 2 STEEL SHEET 6' 3 25⁄64" 2' 6 7⁄16" Wide 36R 4 2 STEEL SHEET 6' 8 33⁄64" Long 2' 6 7⁄16" Wide 38R 2 2 STEEL SHEET 6' 8 33⁄
ABSCO PREMIER SHED MODEL: 30302GK-PTX 10’ W x 10’ D x 7’ H Australian Made COMPONENTS PACKING LIST - (CONT.) CHECK OFF ALL COMPONENTS QTY 2 COMPONENT DESCRIPTION PART No. 84R CHANNEL L = 14' 11 49⁄64" CHECK QTY 4 1 COMPONENT DESCRIPTION PART No.
ABSCO PREMIER SHED MODEL: 30302GK-PTX 10’ W x 10’ D x 7’ H Australian Made COMPONENTS PACKING LIST - (CONT.) CHECK OFF ALL COMPONENTS QTY 10 COMPONENT DESCRIPTION CHANNEL JOINER L= 7 7/8" PART No.
ABSCO PREMIER SHED PremierMODEL: Garden30302GK-PTX Shed - Model: J30232G Australian Made 10’ W x 10’ D x 7’ H INSTRUCTIONS FOR JOINING SPLICED CHANNELS NOTE: THE TEXT MARKED ON ALL PARTS MUST BE SHOWN ON THE SAME SIDE AS EACH OTHER. = = = = CSJ JOIN>> JOIN>> <> J STEP 1. STEP 2. Position the channels and the CSJ joiner channel so the center of the CSJ is in line with the end of each channel to be joined together.
ABSCO PREMIER SHED PremierMODEL: Garden30302GK-PTX Shed - Model: J30302G Australian Made 10’ W x 10’ D x 7’ H STEP 1.
ABSCO PREMIER SHED MODEL: 30302GK-PTX Premier 10’ Garden Shed - Model: J30302G Australian Made W x 10’ D x 7’ H STEP 2. PRE-ASSEMBLY OF SPLICED RIDGE BEAM QTY. = 1 TEK SCREW DRIVER BIT QTY. = 8 SELF DRILLING TEK SCREW RIDGE BEAM 4' 11 7⁄8" PARTS 97AL & 97AR QTY. = 2 QTY.
ABSCO PREMIER SHED MODEL: 30302GK-PTX Premier10’Garden Australian Made W x 10’ D Shed x 7’ H - Model: J30232G INSTRUCTIONS FOR JOINING SPLICED RIDGE BEAM STAGE 1: PUSH RIDGE BEAMS TOGETHER, MAKE SURE THERE IS A 2" OVERLAP OF THE RIDGE CAP 2" INSTRUCTIONAL VIDEOS STAGE 2: INSERT RIDGE CAP JOINER INTO CONNECTED RIDGE CAPS. MAKE SURE JOINER HAS 8 55/64" IN EACH RIDGE CAP. 4" 8 55⁄6 2" STAGE 3: TURN RIDGE CAP OVER AND MEASURE 9 27⁄32" FROM THE END OF EACH RIDGE CAP.
ABSCO INDUSTRIES ASSEMBLY INSTRUCTION - MODEL: 30302GK-PTX ABSCO INDUSTRIES 87A 14A 97A 45A 81A 45A 45A 45A 45A 14A 81A 87A INSTRUCTIONAL VIDEOS 60A PAGE 10 10’ W x 10’ D x 7’ H 23/09/19 ASSEMBLY INSTRUCTION - MODEL: J30302G 26/02/14 87A 45A 45A 45A 87A VIEW OF ROOF COMPONENTS Premier Garden Shed - Model: J30302G ABSCO PREMIER SHED MODEL: 30302GK-PTX Australian Made PAGE 10
ABSCO PREMIER SHED MODEL: 30302GK-PTX 10’ W x 10’ D x 7’ H ABSCO INDUSTRIES ASSEMBLY INSTRUCTION - MODEL: 30302GK-PTX 23/09/19 PAGE 11 NDUSTRIES VIEW OF WALL COMPONENTS ASSEMBLY INSTRUCTION - MODEL: J30302G 26/02/14 INSTRUCTIONAL VIDEOS PAGE 11 Australian Made
ABSCO PREMIER SHED Premier Garden Shed INSTRUCTIONS MODEL: 30302GK-PTXAND VIDEOS Model: Australian Made 10’ W x 10’ 30152GK D x 7’ H ABSCO ASSEMBLY INTRODUCTION The snaptite assembly system locks most perimeter channels to all roof and wall sheets without the need for tools and fasteners.
ABSCO PREMIER SHED PremierMODEL: Garden30302GK-PTX Shed - Model: J30232G 10’ W x 10’ D x 7’ H Australian Made DOOR PANEL ASSEMBLY 58C ATTACH 58C CHANNELS AS DESCRIBED ON PAGE 12 58C 58A 58B B 12A A 58C 58C 58A 89C ATTACH 89C WITH COLORED SIDE FACING OUT.
ABSCO PREMIER SHED Premier 30302GK-PTX Garden Shed MODEL: 10’ WModel: x 10’ D x 7’J30302G H Australian Made REAR PANEL ASSEMBLY LAY SHEETS OUT AS SHOWN 30A 31A 55B 31A 30A 81B INSTALL PEAK BRACE WITH OVERHANG FITTING INSIDE SHED SIDE PANEL ASSEMBLY LAY SHEETS OUT AS SHOWN INS IDE OF SH (2 Required) ED 36R 38R 38L 84R 36L 15A 81A 84L TRIM THE TIP OF EACH SHEET OR BEND OUT OF THE WAY TO ALLOW CHANNELS TO FIT HARD UP TO THE EDGE OF THE SHEET INSTRUCTIONAL VIDEOS ABSCO INDUSTRIES ABSCO INDUSTR
ABSCO PREMIER SHED Premier Garden Shed MODEL: 30302GK-PTX Model: J30302G 10’ W x 10’ D x 7’ H Australian Made ROOF PANEL ASSEMBLY (2 Required) 45A LAY SHEETS OUT AS SHOWN 45A 45A 45A 87A 2 x PRE-PUNCHED HOLES TO THIS END OF EACH SHEET WITH PART NO.
ABSCO PREMIER SHED PremierMODEL: Garden30302GK-PTX Shed - Model: J30232G 10’ W x 10’ D x 7’ H FRONT PANEL ASSEMBLY LAY SHEETS OUT AS SHOWN Australian Made 89A 34A 89A 34A NOTCH ON JAMB 90A FITS OVER JAMB 89A AND 89B AND NOTCH ON 89B AND 89A FITS OVER 55A A 55 89 A A 90 DO NOT INSTALL THIS SCREW (OR THE TOP EQUIVALENT) UNTIL CHANNELS 55A AND 55C ARE INSTALLED 55A 90A 79A 55C A 55 89 A A 79 C 55 NOTCH ON JAMB 89A AND 89B FITS OVER CHANNEL 55C AND CHANNEL 79A INSERTS INTO 55C WITH SHORTE
ABSCO PREMIER SHED MODEL: 30302GK-PTX Premier Garden Shed 10’ W x 10’ D x 7’ H Model: 30152GK INSTRUCTIONS AND VIDEOS Australian Made DOOR PANEL ASSEMBLY 91A 91A B NOTE: Nuts and bolts (supplied) may be used instead of pop rivets (supplied) by simply enlarging the hinge hole sets in the jamb using a 5/32" drill bit A each door have not been pre-punched, to allow for NOTE: The two holes required to connect the padbolt hasp for each 1/8” with holes and secure with screws. shaft, anddrill secure screws.
ABSCO PREMIER SHED MODEL:Garden 30302GK-PTX Premier Shed 10’ W x 10’ D x J30302G 7’ H Model: Australian Made PANEL CONSTRUCTION NOTE: Take care to ensure that both front and rear wall panels are not positioned upside down. The top channel of each panel is pre-punched for attaching roof sheets, the bottom channels are not.
ABSCO PREMIER SHED Premier Garden Shed MODEL: 30302GK-PTX 10’ WModel: x 10’ D x 7’J30302G H ROOF CONSTRUCTION SLIDE THE ROOF PANEL INTO POSITION, AND SECURE WITH ONE SCREW AT EACH CORNER ONLY AT THIS STAGE Australian Made INSIDE VIEW OF FIXING SECURE PEAK BRACE TO RIDGE BEAM AND ROOF PANEL WITH ONE SCREW AT EACH END MOVE THE OTHER ROOF PANEL INTO POSITION AND SECURE PEAK BRACE TO RIDGE BEAM AND ROOF PANEL WITH ONE SCREW AT EACH END INSTRUCTIONAL VIDEOS ABSCO INDUSTRIES ABSCO INDUSTRIES ASSEMBLY INS
ABSCO PREMIER SHED Premier Garden Shed MODEL: 30302GK-PTX 10’ WModel: x 10’ D x 7’J30302G H Australian Made FINAL CONSTRUCTION 14A BEND THE TOP AND BOTTOM FLANGES AS SHOWN, THEN HOOK THE BOTTOM FLANGES UNDER THE TOP CHANNEL AND SCREW THE TOP FLANGES FOR BOTH AS SHOWN GABLE CAPS ANCHORING OF SHED LOCATION OF 12 CONCRETE ANCHORS WALL SHEET BOLT & NUT - EACH ANCHOR CONSISTS OF ONE NUT, BOLT, DYNABOLT AND STEEL ANGLE - DRILL A 25/64" HOLE INTO THE WALL SHEET STEEL ANGLE INSTRUCTIONAL VIDEOS - DRILL A 2
ABSCO PREMIER SHED MODEL: 30302GK-PTX 10’ W x 10’ D x 7’ H Australian Made EXPORT PRODUCT WARRANTY AGAINST DEFECTS Congratulations on your purchase of an ABSCO SHED ABSCO SHEDS, including garden sheds, garden beds, aviaries, storage units, garages, awnings and carports are made using high quality Australian made steel. We are pleased to advise we warrant that the steel coating will not rust, crack, flake peel or blister for 12 years from date of purchase.
