Absco Space Saver Shed Assembly Instructions Model: J30082S INSTRUCTIONAL VIDEOS FRONT BASE LENGTH: 9ft-10-7⁄64in SIDE BASE LENGTH: 2ft-6-45⁄64in FRONT WALL HEIGHT: 5ft-10-55⁄64in REAR WALL HEIGHT: 6ft-4-49⁄64in 2 ft B -1 0 -4 1 SLA RETE CONC ⁄64 in 4in 3⁄6 10ft-2- WHEN LAYING YOUR CONCRETE SLAB, ENSURE THERE IS A REBATED EDGE 1in DEEP AROUND THE PERIMETER CHANNEL E REBATED EDGE T RE THIS WILL HELP WATER EGRESS FROM THE BASE OF THE SHED NC CO AB SL CONCRETE SLAB 3in WIDE REBATE We thank
Absco Space Saver Shed Model: J30082S INSTRUCTIONAL VIDEOS GENERAL INSTRUCTIONS · Before commencing any assembly, read through these instructions in detail to gain a thorough understanding of assembly methods and associated details. · Unpack the carton and carefully identify and check off all the parts against the parts described and illustrated on pages three, four and five. SITE PREPARATION · The site for the shed must be level.
Absco Space Saver Shed Model: J30082S INSTRUCTIONAL VIDEOS COMPONENTS PACKING LIST - CHECK OFF ALL COMPONENTS QTY 6 COMPONENT DESCRIPTION PART No.
Absco Space Saver Shed Model: J30082S INSTRUCTIONAL VIDEOS COMPONENTS PACKING LIST - (CONT.) CHECK OFF ALL COMPONENTS QTY COMPONENT DESCRIPTION 2 STEEL SHEET 2 STEEL SHEET 1 STEEL SHEET 1 STEEL SHEET 4 STEEL SHEET 2 STEEL SHEET PART CHECK QTY No. COMPONENT DESCRIPTION 43B 2 CHANNEL 43C 2 CHANNEL X4L 1 CHANNEL X4R 2 43D 1 34A 4 1 STEEL SHEET A 2 1 STEEL SHEET B 220 PART No.
Absco Space Saver Shed Model: J30082S INSTRUCTIONAL VIDEOS COMPONENTS PACKING LIST - (CONT.) CHECK OFF ALL COMPONENTS QTY COMPONENT DESCRIPTION 2 1 B 88 Part No. Here PART No. COMPONENT DESCRIPTION CHECK QTY 88B 1 89C 4 PART No. CHECK 90A Part No. Here 91A Part No.
Absco Space Saver Shed Model: J30082S INSTRUCTIONAL VIDEOS INSTRUCTIONS FOR JOINING SPLICED CHANNELS NOTE: THE TEXT MARKED ON ALL PARTS MUST BE SHOWN ON THE SAME SIDE AS EACH OTHER. = = = CSJ = JOIN>> JOIN>> <> STEP 1. STEP 2. Position the channels and the CSJ joiner channel so the center of the CSJ is in line with the end of each channel to be joined together.
Absco Space Saver Shed Model: J30082S INSTRUCTIONAL VIDEOS STEP 1.
ABSCO INDUSTRIES ASSEMBLY INSTRUCTION - MODEL: J30082S 14/08/14 88B 43D 43D CUSTOMER SUPPORT - 800-305-4436 43D 81A 81A 43D VIEW OF ROOF COMPONENTS 88B Absco Space Saver Shed - Model: J30082S INSTRUCTIONAL VIDEOS PAGE 8
81J X4R 43B ABSCO INDUSTRIES 43C ASSEMBLY INSTRUCTION - MODEL: J30082S 14/08/14 VIEW OF WALL COMPONENTS 81B 61B 55B 55C 89A 90A 91A 89A 79A 91A 43B 55A CUSTOMER SUPPORT - 800-305-4436 34A 43C Absco Space Saver Shed Model: J30082S 34A X4L A 61B 81J B 22A INSTRUCTIONAL VIDEOS PAGE 9
Absco Space Saver Shed Model: J30082S INSTRUCTIONAL VIDEOS ABSCO ASSEMBLY INTRODUCTION The snap-tite assembly system locks most perimeter channels to all roof and wall sheets without the need for tools and fasteners . SN AP TT i E To pre-assemble the four wall panels and two roof panels, the perimeter channels are secured to the top and bottom of each panel using the snaptite system, as detailed on the following pages wherever you see the symbol.
Absco Space Saver Shed Model: J30082S INSTRUCTIONAL VIDEOS 1.
Absco Space Saver Shed Model: J30082S INSTRUCTIONAL VIDEOS 2.
Absco Space Saver Shed Model: J30082S INSTRUCTIONAL VIDEOS 3. ROOF PANEL ASSEMBLY 43D LAY SHEETS OUT AS SHOWN 43D 43D 81A 43D 88B 81A E APT iT SN 88B ATTACH LIPS 88B AS SHOWN. LIPS SHOULD OVERLAP ROOF CHANNEL 81A.
Absco Space Saver Shed Model: J30082S INSTRUCTIONAL VIDEOS 4. DOOR PANEL ASSEMBLY 58C ATTACH 58C CHANNELS AS DESCRIBED ON PAGE 10 SNAPT iTE 58C SNAPT iTE 58A 58B B 12A A SNAPT iTE 89C 58A 58C ATTACH 89C WITH COLORED SIDE FACING OUT.
Absco Space Saver Shed Model: J30082S INSTRUCTIONAL VIDEOS 89A 5.
Absco Space Saver Shed Model: J30082S INSTRUCTIONAL VIDEOS 6. DOOR PANEL ASSEMBLY 91A 91A INSERT 91A JAMBS UNDER THE CHANNELS AROUND THE DOOR B A NOTE: 8/32in CSK Nuts and bolts (supplied) will require enlarging the hinge hole using a 11/64in drill bit USE 4 x 8/32in NYLOC BOLTS TO SECURE PADBOLT TO DOOR NOTE: The two holes required to connect the padbolt hasp for each door have not been pre-punched, to allow for proper alignment.
Absco Space Saver Shed Model: J30082S INSTRUCTIONAL VIDEOS PANEL CONSTRUCTION NOTE: Take care to ensure that both front and rear wall panels are not positioned upside down. The top channel of each panel is pre-punched for attaching roof sheets. The base channels are not pre-punched.
Absco Space Saver Shed Model: J30082S INSTRUCTIONAL VIDEOS FINAL CONSTRUCTION ANCHORING OF SHED LOCATION OF 8 CONCRETE ANCHORS WALL SHEET BOLT & NUT - EACH ANCHOR CONSISTS OF ONE NUT, BOLT, DYNABOLT AND STEEL ANGLE - DRILL A 25/64in HOLE INTO THE WALL SHEET - DRILL A 25/64in HOLE INTO THE CONCRETE ABSCO INDUSTRIES ASSEMBLY INSTRUCTION - MODEL: J30082S 14/08/14 STEEL ANGLE SLAB DYNABOLT CUSTOMER SUPPORT - 800-305-4436 PAGE 18
