Absco Highlander Shed Assembly Instructions Model: 30292H FOR CONSTRUCTION IN NON-CYCLONIC AREAS WIND RATING: W33N (N2) FRONT: SIDE: WALL HEIGHT: GABLE HEIGHT: 3.00m 2.92m 2.035m 2.300m 20 30 m m CONCRETE SLAB 3100mm WHEN LAYING YOUR CONCRETE SLAB, CHAMFER THE 50mm EDGES DOWNWARDS BY 10mm. 50mm 10mm 50 mm THIS WILL ENSURE THAT WATER RUN OFF IS KEPT CLEAR FROM YOUR SHED We thank you for choosing an Australian Made Shed.
Absco Highlander Shed - Model: 30292H GENERAL INSTRUCTIONS Before commencing any assembly, read through these instructions in detail to gain a thorough understanding of assembly methods and associated details. Unpack the carton and carefully identify and check off all the parts against the parts described and illustrated on pages three to five. SITE PREPARATION The site for the shed must be level.
Absco Highlander Shed - Model: 30292H COMPONENTS PACKING LIST - CHECK OFF ALL COMPONENTS QTY COMPONENT DESCRIPTION PART CHECK QTY No.
Absco Highlander Shed - Model: 30292H COMPONENTS PACKING LIST - (CONT.) CHECK OFF ALL COMPONENTS QTY 1 2 1 4 COMPONENT DESCRIPTION PART No. 79A CHANNEL L = 1568mm COMPONENT DESCRIPTION 2 PART No.
ABSCO INDUSTRIES ASSEMBLY INSTRUCTION - MODEL: 30292H 26/11/10 VIEW OF ROOF COMPONENTS Absco Highlander Shed - Model: 30292H PAGE 5
81G HRC H30 ABSCO INDUSTRIES VIEW OF WALL COMPONENTS 81B 59A 77B 16R H31 13A H31 16L HRC H30 H34 16L HRC ASSEMBLY INSTRUCTION - MODEL: 30292H 26/11/10 H31 H31 Absco Highlander Shed - Model: 30292H 13A 79A H31 90A 91A 91A HJ1 55C 81G H31 59A E HRC HJ1 H34 F 16R PAGE 6 22A 77A
Absco Highlander Shed - Model: 30292H ABSCO ASSEMBLY INTRODUCTION The snap-tite assembly system locks all perimeter channels to all roof and wall sheets without the need for tools and fasteners . To pre-assemble the four wall panels and two roof panels, the perimeter channels are secured to the top and bottom of each panel using the snaptite system, as detailed on the following pages wherever you see the symbol.
Absco Highlander Shed - Model: 30292H DOOR PANEL ASSEMBLY 58C 58C HC1 F 12A E 58C HC2 HJ3 HC1 58C F E 20mm FLANGE 15mm FLANGE FOUR HOLE SET FOR PADBOLT CONNECTION ABSCO INDUSTRIES ASSEMBLY INSTRUCTION - MODEL: 30292H 26/11/10 PAGE 8
Absco Highlander Shed - Model: 30292H REAR PANEL ASSEMBLY H30 H31 77B H31 H30 81B SIDE PANEL ASSEMBLY (2 Required) H31 H31 SMALL PAN 59A SMALL PAN 81G ABSCO INDUSTRIES ASSEMBLY INSTRUCTION - MODEL: 30292H 26/11/10 PAGE 9
Absco Highlander Shed - Model: 30292H ROOF PANEL ASSEMBLY (2 Required) 44R 45A 45A 44L 87B 2 x PRE-PUNCHED HOLES TO THIS END OF EACH SHEET WITH PART NO.
Absco Highlander Shed - Model: 30292H HJ1 FRONT PANEL ASSEMBLY H34 HJ1 H34 77A 90A 79A 55C ABSCO INDUSTRIES ASSEMBLY INSTRUCTION - MODEL: 30292H 26/11/10 PAGE 11
Absco Highlander Shed - Model: 30292H DOOR PANEL ASSEMBLY 91A 91A F E NOTE: Nuts and bolts (supplied) may be used instead of pop rivets (supplied) by simply enlarging the hinge hole sets in the jamb using a 4mm drill bit NOTE: The two holes required to connect the padbolt hasp for each door have not been pre-punched, to allow for proper alignment.
Absco Highlander Shed - Model: 30292H PANEL CONSTRUCTION NOTE: Take care to ensure that both front and rear wall panels are not positioned upside down. the top channel of each panel is pre-punched for attaching roof sheets, the bottom channels are not.
Absco Highlander Shed - Model: 30292H ROOF CONSTRUCTION OUTSIDE VIEW INSIDE VIEW ROOR OVERHANGS ALL WALL PANELS BY 37mm SECURE RIDGE BEAM TO GABLE SECTIONS WITH TWO SCREWS AT EACH END. SECURE EACH ROOF PANEL WITH ONE SCREW IN EACH CORNER ONLY AT THIS STAGE 37mm AFTER THE ROOF PANELS HAVE BEEN SECURED, FIT TWO GABLE BRACES (13A) FROM THE TOP WALL CHANNEL TO THE UNDERSIDE OF THE RIDGE BEAM AT 45 DEGREES AS SHOWN TO BOTH GABLE WALLS.
Absco Highlander Shed - Model: 30292H FINAL CONSTRUCTION 14A BEND THE TOP AND BOTTOM FLANGES AS SHOWN, THEN HOOK THE BOTTOM FLANGES UNDER THE TOP CHANNEL AND SCREW THE TOP FLANGES FOR BOTH AS SHOWN GABLE CAPS ANCHORING OF SHED LOCATION OF 12 CONCRETE ANCHORS WALL SHEET BOLT & NUT - EACH ANCHOR CONSISTS OF ONE NUT, BOLT, DYNABOLT AND STEEL ANGLE STEEL ANGLE - DRILL A 10mm HOLE INTO THE WALL SHEET SLAB - DRILL A 10mm HOLE INTO THE CONCRETE ABSCO INDUSTRIES DYNABOLT ASSEMBLY INSTRUCTION - MODEL: 302
PRODUCT WARRANTY Congratulations on your purchase of an ABSCO Product. ABSCO SHEDS are made using high quality Bluescope™ Australian made Zincalume™ or Colorbond Steel™. We are pleased to advise we warrant that this steel will not rust, crack, flake peel or blister for 20 years from date of purchase.
ABSCO STEEL BUILDINGS- STORAGE GUIDELINES ABSCO steel buildings include garden sheds, storage units, aviaries, garages and carports. ABSCO steel buildings are designed to be weatherproof for normal weather conditions. In the event of extreme weather conditions such as heavy rain, combined with high wind gusts, the ridge capping, sheeting joins, screw fixings etc., may exhibit minor deformations which may allow some water entry.
