Eycasa Door & House Wireless Video System User Guide Version 12/2013 Original user guide in German. Retain for future reference.
English Introduction Dear customer, Thank you for purchasing this product. This product complies with current European regulations. The declaration of conformity can be obtained from: ABUS Security-Center GmbH & Co. KG Linker Kreuthweg 5 86444 Affing GERMANY To maintain this status and to guarantee safe operation, it is your obligation to observe these operating instructions.
English Explanation of symbols The triangular high voltage symbol is used to warn of the risk of injury or health hazards (e.g. caused by electric shock). The triangular warning symbol indicates important notes in this user guide which must be observed. This symbol indicates special tips and notes on the operation of the unit. Important safety information All guarantee claims are invalid in the event of damage caused by non-compliance with this user guide. We cannot be held liable for resulting damage.
English 7. Wireless transmission The wireless range depends on a variety of environmental factors. The local conditions at the installation site may have a negative impact on the range. A range of up to 100 m can be achieved if there is line of sight between the receiver and transmitter, and a range of up to 30 meters can be achieved indoors (this can be less depending on the situation in the building).
English Contents 1. Intended use ............................................................................................................................................................6 2. Eycasa system components ..................................................................................................................................6 3. Features and functions ..................................................................................................................................
English 1. Intended use The Eycasa wireless intercom system, consisting of a main unit and the video door station, gives you the advantage of using 2.4 GHz wireless digital radio (for video data) and DECT (for audio data) to operate your video intercom. Alternatively, the video door station can be operated on a permanent power supply (recommended) or on batteries at the front door.
English 3. Features and functions Eycasa door & house wireless video system for watching, speaking, listening, and switching The Eycasa door & house wireless video system set contains the Eycasa video door station and Eycasa main unit Secure wireless transmission using 2.4 GHz digital wireless for video and 1.
English 4. Device description 4.1 Description of the Eycasa main unit Board marker Used for writing short notes on the memo board. Dry erase board marker. Microphone Intercom for Eycasa video door station and Eycasa FamilyCare camera. Memo board Glass plate for short notes with Eycasa board marker. Switch to event list. Eycasa control buttons Switch to live image. Back button (within menus).
English Table mount Removable table mount, can be used instead of the included wall mount. Power supply 12 V DC / 1 A Device starts automatically when powered by line voltage. RJ45 connection Integrated network access, 10/100 Mbps. Loudspeaker System loudspeaker for outputting audio. 4.
English Doorbell button Backlit doorbell button (not in battery mode). Backlighting switches on automatically in night mode (camera photo sensor). When the doorbell button is pressed, a connection to the Eycasa main unit is established with a video image. Built-in microphone for two-way voice communication with Eycasa main unit or handset. Microphone ABUS logo Proximity reader Connector block (Rear) Battery compartment Removable battery compartment for 6 x AA batteries (1.5 V).
English Connection examples for an electronic door opener/door bell Description of the terminal block Description 12V-24 AC/DC RELAY 1 RELAY 2 Note Network connection for video door station 12-24V direct current or 12-24V alternating current Terminal connector for electronic door opener. Potential-free relay, NO (normally open) Terminal connector for electronic door bell.
English Connection for an electronic door bell: Connect the electronic door bell to RELAY 2. Before use, ensure that your door bell has a suitable opening contact for triggering. The door bell is supplied with power via the door bell’s intended voltage source (separate power supply unit or batteries). When using an electromechanical door bell, use the power supply via RELAY 2 so that the bell is triggered when switched by closing the circuit.
English 4.3 Description of the Eycasa outdoor camera Antenna Screw-on antenna for 2.4 GHz digital wireless. Photo sensor Sensor for switching between day and night mode. Camera Camera with fixed lens. Power LED LED red LED off Permanently lit Permanent LED green Lit LED green Flashing LED off Permanent Link LED Power supply connected. No power supply connected. Camera is providing an image signal to the main unit. Pairing mode active.
English 4.4 Description of the Eycasa Family Care camera Camera module with fixed lens and IR LEDs, including photo sensor. Built-in IR LEDs. Activated in night mode. Camera Status LED Mikrofone Antenna Antenna for 2.4 GHz digital wireless. Power button Switch on Family Care camera (press for 3 seconds). Switch off Family Care camera (press for 3 seconds).
English 5. Pairing the system components 5.1 Pairing the Eycasa components in the Eycasa main unit We recommend that you pair the video door station in the entrance area to camera position 1 (factory setting with the CASA31000). All other components can be paired to any of the other camera positions. Pair the components as follows: Note: The CASA31000 Eycasa video door station and Eycasa main unit included in delivery are already programmed at the factory.
English First remove the battery compartment to be able to remove the front cover. You can now continue the pairing process for your video door station. The setup wizard of your main unit should show the following view: A notification message will appear that a camera already paired to the selected camera slot will be overwritten by this action. Press Next if you are sure you want to continue with the pairing process.
English Your Eycasa main unit connects to your video door station. The process can take several seconds. The setup wizard will signal whether the process is complete or whether it needs to be repeated due to a pairing error. If the message “Video door station was successfully paired” appears, the pairing process is finished. The status LED goes out on your video door station, signaling readiness. You can proceed with installation of the unit from Chapter 6.
English 5.3 Pairing the Eycasa outdoor camera Ensure that your Eycasa outdoor camera is supplied with power. You can now proceed with the pairing process for your outdoor camera. The setup wizard of your main unit should show the following screen: Follow the instructions on the screen and press and hold the pairing button on the power cable of the camera. The link LED of the camera starts to flash. Now press “Next” without releasing the pairing button.
English Follow the instructions on the screen and press and hold the pairing button on the camera. The Status LED on the camera starts flashing red and green. Now press “Next”. Your Eycasa main unit then connects to the Family Care camera. The process can take several seconds. The setup wizard will signal whether the process is complete or whether it needs to be repeated due to a pairing error. If the message “Family Care camera was successfully assigned” appears, the assignment process is finished.
English 6. Mounting the system components 6.1 Mounting the Eycasa main unit The Eycasa main unit can be installed either on a table or wall. When delivered, the table mount is already attached, allowing you to place the device wherever you would like indoors. Alternatively, the back cover of the main unit can be replaced with the included wall mount. The following steps describe how to install the wall mount.
English 4. Now place the main unit on the wall mount and connect the included power supply unit. Ž 6.2 Mounting the Eycasa video door station The Eycasa video door station can be mounted either horizontally or vertically. The video door station is designed for use in protected outdoor areas, thanks to its degree of protection of IP54. Note: In case of horizontal installation, in the settings you need to change the orientation of the video image to 90° to the left or right.
English 55 mm You can now open the plastic cover of the doorbell button and attach your nameplate. For labeling, you can use the included nameplate or the PDF template on the included CD. 55 mm Connect the power (12–24 V AC/DC) and an optional electronic door opener (RELAY 1) and/or an electronic door bell (RELAY2) to the terminal block of the video door station. Note: In software version 1.0, RELAY 2 is disabled for the Eycasa main unit. Important: When operating with a permanent power supply (e.g.
English After connecting the power supply, mount the video door station on the house wall. The recommended installation height is 1.6 meters between the ground and camera module. Put on the video door station at the desired location and use the screw holes on the bottom shell to mark the drill holes. After finishing the wall mounting, put the door station back together to complete the installation. 6.
English 6.4 Mounting the Eycasa Family Care camera Bolt the camera onto the bracket and select a suitable place to mount it. You can decorate the camera with one of the stickers provided. The camera should be mounted no further than 3 metres away from the child in order to ensure optimum visibility and reliable sound detection. Important: Please make sure the camera and the cable are well out of reach of your child in order to prevent the risk of strangulation.
English 7. System operation 7.1 Start-up of the Eycasa main unit Sequence: 1. 2. 3. 4. 5. 6. Connect the power supply unit to your Eycasa main unit. The device starts automatically after the line voltage is present. Wait until the boot process is complete. During initial start-up, the system language is set after the system boots. Select the language by pressing the corresponding country flag on the display. Press the button twice to return to the live view. 7.
English Operates RELAY 1 on the video door station to open the door. Key Establish/terminate a voice connection to the video door station. Receiver Lullaby Play a preset lullaby on the Family Care camera for 90 seconds. The lullaby is repeated until 90 seconds have passed. You can end the lullaby manually by pressing the button. Monitoring mode Activates monitoring mode on the Family Care camera (voice activation is enabled). The function remains active until it is manually deactivated again.
English 7.3 Event list and event behavior Event list In the event list, the following control options are available: Changes the view to the event list. You can browse through the event list in steps of seven using the buttons. The event log includes 500 entries. Opens the general filter dialog of the event list. After activation of the filter type, only events of the selected type are displayed. When a camera is selected, the event list only shows events of the selected camera.
English Battery strength: Shows the time of weak battery strength on an Eycasa video door station and Family Care camera. When the battery is low, the video door station automatically switches off video transmission. Change the batteries promptly if this message appears. 7.3.1 Playback of event recordings Event list Possible user actions Select an entry with the video symbol from the event list Effect The view automatically switches to playback and the video is played.
English 7.3.1 Doorbell event Sequence of doorbell ringing: 1. Doorbell is pressed on the video door station. 2. The screen on the Eycasa main unit is activated. 3. RELAY2 on the door station is switched for 2 seconds to activate the door bell. 4. The live image of the video door station is displayed. 5. Video recording is started on the video door station and continues for up to 30 seconds (if the “Activate video recording” option was selected in the settings). 6. The doorbell tone plays. 7.
English 7.3.2 Proximity key event Sequence of the proximity application: 1. Hold the paired proximity key up to the video door station. 2. The door opener (RELAY 1) on the video door station is operated. 3. The screen on the Eycasa main unit is activated. 4. The live view switches to the video door station with the activated proximity key. 5. The event message is displayed on the screen. 7.3.3 Motion event Sequence of motion detection: 1. Outdoor camera detects motion using the integrated PIR sensor. 2.
English 7.3.5 Family care event Voice activation sequence: 1. The VOX function of the Family Care camera is activated using the monitoring function on the main unit. 2. The integrated voice detection function of the Family Care camera detects a sound source. 3. The screen on the Eycasa main unit is activated. 4. The live image of the Family Care camera is displayed. 5. An audio connection to the Family Care camera is started up (listening only) for 30 seconds. 6.
English 7.4 General system settings Pressing the button gives you access to the system settings. Note that you can block access to the settings menu by assigning a PIN. You can save settings in the submenus by pressing the the higher-level item in the main menu. button. Pressing this button also takes you to 7.4.1 PIN lock settings By assigning a 4-digit PIN, you can secure your Eycasa main unit against unauthorized access to the system settings.
English 7.4.2 Software update settings Here you can update the software of your Eycasa main unit using an SD card. On our homepage, http://www.abus.com , you can check whether a new firmware file is available for the CASA31000 Eycasa main unit. The following steps must be carried out with the update: 1. Download the firmware update from the ABUS homepage. 2. Unzip the update to an SD card. 3. Insert the SD card into main unit and start updating.
English 7.4.4 Screen saver settings Select the activation time for the screen saver. The screen saver is automatically activated after the set time if during this time there has been no user input on the touchscreen and no events on the main unit. The monitor dims in this mode, but the system functions are still active. The screen saver is automatically deactivated at any time if the touchscreen is touched anywhere or if an event occurs.
English 7.4.6 Time and date settings Here you set the current time, date, and time zone. These settings are important for proper recording of the messages in the event log of the main unit. Activate the “Automatic” setting if your Eycasa main unit is connected to your home network (which provides access to the internet). The current time is identified automatically via NTP (Network Time Protocol) any regularly synchronised. Synchronisation takes place once a day or when the Eycasa main unit is restarted.
English Activate network DHCP Manual IP address IP address Subnet mask Gateway DNS address Activates/deactivates the network port of the Eycasa main unit. If this function is activated, your main unit takes its IP configuration from your router (or another network device with a DHCP server). If this function is activated, you can make the IP address configuration manually. Enter the IP address here. Make sure that the address you choose is not used by any other device.
English 7.5 Camera settings The camera settings allow you to pair new cameras in the Eycasa main unit and change the configuration. Depending on the paired camera type, different configuration elements are available. General camera settings: Selection of the camera channels 1–4. The currently selected camera is highlighted in blue. Input field for camera name with a maximum of 12 characters. Choose a suitable name for your camera (such as front door or backyard). Display of the camera type.
English the setting is deactivated, the video image of the door station is transmitted only during the doorbell ringing process. This setting is not relevant for operation of the door station in battery mode. Setting of the loudspeaker volume on the video door station. Important: In order to ensure legal compliance, it is recommended that continuous transmission of the video image be deactivated when publicly accessible spaces can be viewed.
English Family Care camera settings: Setting the lullaby. This tune is played when you press the “Lullaby” button on the main unit of the Family Care camera. Voice detection sensitivity setting of the Family Care camera. The higher the set value, the more quickly the camera reacts to sounds, and triggers the VOX alarm. Setting for turning the Family Care camera image 90° to the left or right if installed to do so. Loudspeaker volume setting of the Family Care camera. 7.
English You can play the recorded video data directly via the event list if the Eycasa main unit, or play it on your PC. The video data is saved in the \eycasa\videofiles folder on the SD card. Important: The recording function operates using the integrated circular buffer of the event list. The circular buffer has a capacity of 500 entries. Once this has been reached, older entries and video data are overwritten.
English After successful pairing, you can specify a name for the chip key and then pair further keys. If you answer the question with “No”, pairing mode is terminated on all video door stations. Managing proximity keys Press a key from the list to select it and display the chip key management options. Change the chip key name: Change the name of your chip key using the on-screen keyboard.
English 7.8 Factory settings Select “Reset” to reset your Eycasa main unit to the factory settings. The following settings are deleted: All settings for doorbell tones are set to the standard settings. All camera names are deleted. The wireless connection to all connected cameras is deleted. All camera settings (alarm, rotation, volume) are deleted. The event list is deleted. The current PIN is deleted. All audio settings are reset to the standard settings.
English 8. Maintenance and cleaning 8.1 Maintenance Examine the technical safety of the product regularly, e.g. check the housing for damage. If it seems that it may no longer be possible to operate the device safely, stop using the product and protect it from unintentional use. It is likely that safe operation is no longer possible in the event that: The device shows signs of visible damage. The device no longer works correctly.
English 10.
English Audio transmission power Audio sensitivity Audio data rate Wireless range Event log Adjustable alarm tone Loudspeakers Microphone Network Storage medium Power supply Power consumption Degree of protection Operating temperature Dimensions (W x H x D) Net weight < 20 dBm -82 dBm 64 Kbps 30 m (depending on site conditions) * 500 5 doorbell tones 8 Ohm, 2 W x 2 Integrated RJ45 10/100 Mbit Ethernet SDHC card, max. 32 GB 12 V DC / 1 A Max.
English CASA30500 Eycasa outdoor camera Model number Frequency Modulation Transmission power Sensitivity Resolution Lens Horizontal angle of view Number of IR LEDs Range of night vision function IR angle IR swivel filter Frequency Modulation Data rate Transmission power Sensitivity Wireless range Compression Frame rate Power supply Power consumption Degree of protection Operating temperature Dimensions Net weight 2.4 GHz GFSK 16 dBm -82 dBm 640 x 480 pixels (VGA) 3.6 mm 60° 27 IR LEDs Approx.
