Progressive Scan CCD network camera Installation instructions Version 1.
Preface Dear Customer, Thank you for purchasing this network camera of the Eyseo series from ABUS Security-Center. You made the right decision in choosing this state-of-the-art technology, which complies with the current standards of domestic and European regulations. The CE has been proven and all related certifications are available from the manufacturer upon request.
Before using this product The use of surveillance equipment may be forbidden by law in some countries. This network camera is not only high-quality web camera but can also be used as part of a flexible surveillance system. Before using this equipment, make sure that all your surveillance activities are completely legal. Before installation, check the product for completeness (page 5: Scope of delivery). Read the installation instructions before installing the network camera.
Contents Preface .....................................................................................................................................................2 Precautions ...............................................................................................................................................2 Before using this product ..........................................................................................................................3 Contents ............................
Scope of delivery Network camera TV7220/TV7221/TV7222/TV7223 Lens Antenna (only TV7221/23) Transformer Camera stand Software CD Installation instructions (on CD) 5
Hardware installation Make sure that all accessories and articles listed above are present in the scope of delivery. Depending on application, an Ethernet cable may be required. This Ethernet cable must meet the specifications of UTP Category 5 (CAT 5) and must not be longer than 100 meters. To prevent the risk of electric shock, first connect the socket of the transformer to the network camera before inserting the transformer into the mains socket.
External connections Connections at the rear side Audio output Switch: internal / external Microphone Antenna 12VDC Audio input Ethernet connector I/O-Port Reset button I/O-connector 1 : not used 2 : not used 3 : not used 4 : not used 5 : Ground 6 : Digital input 7 : Digital output 8 : Power 12VDC Switching input and output 7
First access to network camera The first access to the network camera should be done by using the Installation Wizard 2. After the startup of this tool the wizard will search for any connected Eyseo network camera or videoserver. The Standard IP address of the videoserver is 169.254.0.99. If there is a DHCP server running on the network then the IP address assignment will be done automatically, regarding your network stucture.
Access to the network camera via the Internet Explorer Defining a password to prevent unauthorised access When delivered, no administrator password is defined for the network camera. The network camera asks for this number at the start of operation. For security reasons, the administrator should define a new password immediately. After the new administrator password is stored, the network camera asks for the user name and password every time it is accessed.
Changing the administrator password Click “Configuration” and then “Security”. Under “Root password”, enter the administrator password and confirm it under Confirm password. Click . The new administrator password is saved. Click “HOME” in the column on the left to exit configuration.
Installing the plug-in When you first access the network camera under Windows, the web browser may ask for the installation of a new plug-in for the network camera. This query depends on the Internet security settings of your PC. If the highest security level is set, the PC will refuse any installation and any attempt at execution. This plug-in is used for video display in the browser. To continue, click .
Basic user functions Main window and camera view The view of the main page consists of two parts: Configuration: You can configure the camera with these steps. Camera view: Camera video stream Click the configuration link on the left of the picture to open the configuration page. Language: Selection for the GUI language of the camera. Digital output: Here the external digital output can be switched manually. Local Recording : Recording to local PC harddrive can be started and stopped.
Digital Zoom and Snapshot Click the magnifying glass under camera view. The control field for digital zooming appears. Disable the Disable Digital Zoom box and change the zoom factor with the slider. Click “Snapshot”. The web browser displays a new window containing the snapshot. To save the snapshot, either left-click it and then click the diskette icon or right-click it and select Save from the context menu.
Client Settings When you first access the Connection Type page under Windows, the web browser asks for the installation of a new plug-in. This plug-in was registered at certification and can be used to change parameters on the Client settings page. To install the plug-in, click . If the web browser prevents continuation of the installation, open the Internet security settings and reduce the security level or consult the IT administrator or network administrator.
The selection of the client is normally recommended in the following order: UDP – TCP – HTTP. When the network camera has been successfully connected, the “Protocol Options” box shows the selected protocol. The selected protocol is registered in your PC and used for the next connection. After changing the network environment or if you want to search again for the network camera using the web browser, select the UDP protocol manually, save it and then return to “HOME” to set up the connection again.
Administrator settings Configuration / video and audio Best performance is produced by the maximum frame rate with best video quality and minimum network bandwidth. The three factors “Max frame rate”, “Constant bit rate” and “Fixed quality” on the video configuration page are interrelated. Mobile access to the network camera Many modern mobile telephones support access to MPEG4 videostream and GSM-AMR audio data. Due to restricted bandwidth, only a maximum resolution of 176x144 pixels is supported.
For higher-quality pictures For best video quality, set “Fixed quality” to “Detailled” or “Excellent” and the “Max frame rate” so that it corresponds to the bandwidth of your network. If your network is slow and you get “broken” images, go to the TCP protocol under Connection Type and select a more suitable transmission mode. Pictures can also be affected by a time delay due to a slower connection. The more users in the network, the greater this time delay.
Opening accounts for new users Under “Configuration”, select “Security”. Now go to the “Add user” section. Add an account with user name and password for a second user. You can define up to twenty accounts for other users of the network camera. The camera checks only the access permission of the corresponding user name and password. This means that two or more users can use the same account at different levels.
System configuration Only the administrator has access to system configuration. The following sections explain each element in the left column. Specific tasks on the Options page are printed bold. The administrator can enter the URL under the picture to jump direct to the pictures page of the configuration. http://”Network Camera”/setup/config.html is the domain name or original IP address of the network camera. http://”Network Camera”/setup/system.
System „Host name“ The text represents the title of the homepage. „Turn off the LED indicator“ Select this option to switch off the LED on the front of the camera. This prevents other persons knowing that the camera is in use. „Keep current date and time“ Click this option to keep the current date and time of the network camera. An internal realtime clock stores the date and time after the system is switched off.
Network All changes made on this page cause a system reboot so that they can take effect. Make sure that the fields are correctly filled before you click “Save”. Network connection “LAN” The default is LAN. Use this setting if the camera is connected to a LAN. You also have to make other settings such as the IP address or the subnet mask. “PPPoE” Use this setting if the camera is connected directly to a DSL modem. You will receive a user name and password from your ISP (Internet Service Provider).
RTSP streaming: “RTSP-Authentication” Enable the authentication of RTSP. On connection to an RTSP client username and password will be checked. Note: This function must be supported by the media player (e.g. Realplayer 10.5) “Access name for stream 1” The access name for establishing a connection from a client. The codec type must be MPEG 4! Use rtsp://:RTSP-port/ to establish a connection. “Access name for stream 2” The access name for establishing a connection from a client.
http:///setup/network.html is the domain name or original IP address of the network camera.
WLAN configuration “SSID” (Service Set Identifier) The name that identifies the wireless network. The access point and the WLANnetwork camera must use the name SSID. The factory setting is “default”. IMPORTANT: The max. length is 32 characters; do not use: “ , ”, <, > and spaces. “Wireless mode” Select one of the following: “Infrastructure” Thenetwork camera is connected to the network via an access point.
http:///setup/wireless.html is the domain name or original IP address of the network camera.
Enable the DDNS function „Provider“ The provider list contains four hosts that provide DDNS services. Connect to the serviceprovider’s website to make sure that the service is available. „Host name“ This field must be completed if you want to use the DDNS service. Enter the hostname registered with the DDNS server. „Username/Email“ The user name and the e-mail address must be entered in this field to set up a connection to the DDNS server or to inform users about the new IP address.
Access list “Allow list” The IP list of accepted IPs is entered here and added to the access list. As a factory default, all IPs are accepted. If necessary, delete the entire list. “Start IP address” Enter the first address of the desired range. “End IP address” Enter the last address of the desired range. “Delete allow list” Delete desired ranges from the access list. “Deny list” Define the IP lists to be blocked. “Delete deny list” Delete blocked IP lists. http:///setup/accesslist.
Video and audio Video “Video title” The text appears in the black bar above the video window with a timestamp. This timestamp (date and time) is supplied by the network camera, and the date and time are supplied by an integrated realtime clock. “Color” Selects between colour and monochrome display. “Power line frequency” Fluorescent light pulses with the mains frequency. Adapt the mains frequency to eliminate this pulsing in the picture.
Picture settings Click “Image settings” to open another window in which you can set the “Brightness”, “Contrast”, “Saturation” and the “Sharpness” of the video picture. To check your settings, click “Preview”. To save the picture parameters, click “Save”. To discard your changes, click “Restore”. “White balance” Set the value for an optimal colour hue. Privacy Mask Using this function you can mask parts of the video picture. At most 5 windows can be setup simultaneously.
CCD settings „IRIS level“ Controls the aperture of the auto iris lens manually „AGC“ Automatic gain control: Normal or Maximum “AES” Auto Electronic Shutter “ALC” Automatic light control, fixed shutter speed “Low Lux Mode” extends the shutter speed in low lux environment „BLC“ Backlight compensation: It will help to identify objects in front of strong light sources.
Motion sensor “Enable motion detection” Enables motion detection. “New” Adds a new window. A maximum of three windows can be open simultaneously. To resize the window or move the title bar, click the window frame, keep the mouse button pressed and drag the window to the required size. Close the window by clicking the “x” in the top right corner. “Save” Click this button to save window settings. A bar graph rises or falls according to the picture variation.
Application There are 3 sections in application page: Event, Server and Media Settings. To create an application event the basic order for configuration is: Media -> Server -> Event. There can be setup at most 3 events, 5 servers and 5 medias. http:///setup/application.html Media Media name The unique name for the media. There are 3 kind of media: Snapshot, video clip and system log.
Server Server name The unique name for a server. There are four kind of servers supported. Those are email server, FTP server, HTTP server and network storage. Email Server Sender email address The email address of the sender Recipient email address The email address of the recipient Server address The domain name or IP address of the external email server. User name This granted user name on the external email server. Password This granted password on the external email server.
Event Event name The unique name for an event. Enable this event Check it to enable this event. Priority The event with higher priority will be executed first. Delay second(s) before detecting next event The delay to check next event. It is used in motion detection and digital input trigger type. The videoserver supports 3 different trigger types: Video motion detection Select the windows which need to be monitored. Periodic The event is triggered in specific intervals.
Recording The network camera supports recording on network storage. The operation of editing recording item is the same as the one in the application page. User can define the recording name, status, weekly and time schedule, stream source and destination of recording. There can be at most 2 recording entries. To do recording on network storage, please add network storage server in application page first. Recording entry name The unique name for the recording entry.
Viewing the log file Click this link on the configuration page to display the system log file. The contents of the file supply useful information about the configuration and the connection following a system start. The standard of the log file is RFC 3164. You can also send data to a log server. Enable “Remote Protocol” and enter the IP address and the port number of the server. Viewing parameters Click this link on the configuration page to display all system parameter sets.
Appendix A. Troubleshooting Status LEDs Condition / LED Color System start During boot up Network search/setup Network ok During Firmware Upgrade Green On Off On 1/s 1/s Red 1/s (once) 1/s Off On 0.1/s Resetting and restoring At the back side of the netzwork camera is a button. Press this button to reset the system or restore the factory parameter settings. Sometimes the normal system status can be restored by a reset.
B. Frequently asked questions (FAQ) Q. What do I do if I forget my password? A. Every access to the network camera requires an authentication. If you are one of the managing users, ask your administrator for your password. If you are the administrator, there is no way of reactivating the root password. The only way of accessing the network camera is to press the reset button on the rear of the camera to restore the factory-set parameters and then reconfigure the system. Q.
Q. Why is access to the network camera not possible while I am setting options in the application? A. If the network cameras are started by events, snapshots need more time since they are written to memory. If the events occur too often, the system is constantly trying to store the pictures. If an event occurs very frequently, use sequential mode or an external recording program to record the pictures.
C. URL-Commands Style convention In URL syntax and in descriptions of CGI parameters, a text within angle brackets denotes a content that is to be replaced with either a value or a string. When replacing the text string also the angle brackets shall be replaced. An example of this is the description of the name for the server, denoted with in the URL syntax description below, that is replaced with the string myserver in the URL syntax example, also below.
http://mywebserver/cgi-bin/dido/setdo.cgi?do1=1 Security level SECURITY LEVEL SUB-DIRECTORY DESCRIPTION 0 anonymous Unprotected. 1 [view] anonymous, viewer, dido, camctrl 1. Can view, listen, talk to camera 2.
any parameters, all the parameters on the server will be returned. If you specify only , the parameters of related group will be returned. When query parameter values, the current parameter value are returned. Successful control request returns paramter pairs as follows. Return: HTTP/1.0 200 OK\r\n Content-Type: text/html\r\n Context-Length: \r\n \r\n where is =\r\n [] is the actual length of content.
Syntax: http:///cgi-bin/anonymous/setparam.cgi? = [&=…][&update=][&return=] http:///cgi-bin/viewer/setparam.cgi? = [&=…][&update=] [&return=] http:///cgi-bin/operator/setparam.cgi? = [&=…][&update=] [&return=] http:///cgi-bin/admin/setparam.
where is =\r\n [] Only the parameters that you set and readable will be returned. Example: Set the IP address of server to 192.168.0.123 Request: http://myserver/cgi-bin/admin/setparam.cgi?network_ipaddress=192.168.0.123 Response: HTTP/1.0 200 OK\r\n Content-Type: text/html\r\n Context-Length: 33\r\n \r\n network.ipaddress=192.168.0.
Disable]. , Enumeration. Only given values are valid. , , … blank A blank string everything inside <> As description NOTE: The camera should prevent to restart when parameter changed. Group: system NAME VALUE SECURITY DESCRIPTION (get/set) hostname string[40] 1/6 host name of server ledoff 6/6 turn on(0) or turn off(1) all led indicators date , 6/6 Current date of system. Set to ‘keep’ keeping date unchanged.
-360: GMT-09:00 Alaska -320: GMT-08:00 Las Vegas, San_Francisco, Vancouver -280: GMT-07:00 Mountain Time, Denver -281: GMT-07:00 Arizona -240: GMT-06:00 Central America, Central Time, Mexico City, Saskatchewan -200: GMT-05:00 Eastern Time, New York, Toronto -201: GMT-05:00 Bogota, Lima, Quito, Indiana -160: GMT-04:00 Atlantic Time, Canada, Caracas ,La Paz, Santiago -140: GMT-03:30 Newfoundland -120: GMT-03:00 Brasilia, Buenos Aires, Georgetown, Greenland -80: GMT-02:00 Mid-Atlantic -40: GMT-01:00 Azores, Ca
83: GMT 02:00 Israel 120: GMT 03:00 Baghdad, Kuwait, Riyadh, Moscow, St.
Is., New Caledonia 480: GMT 12:00 Aucklan, Wellington, Fiji, Kamchatka, Marshall Is. 520: GMT 13:00 Nuku'Alofa updateinterval 0, 6/6 0 to Disable automatic time adjustment, otherwise, it means the seconds between NTP automatic update interval. 7/6 Restore the system parameters to default value. Restart the server after seconds. 7/6 Restart the server after seconds. 7/6 Restore the system parameters to default value except (ipaddress, subnet, router, dns1, dns2, ddns settings).
1)> Group: status NAME VALUE SECURITY DESCRIPTION (get/set) di_i<0~(ndi-1)> 1/7 0 => Inactive, normal 1 => Active, triggered do_i<0~ndi-1)> 1/1 0 => Inactive, normal 1 => Active, triggered onlinenum_rtsp integer 6/7 current RTSP connection numbers onlinenum_httppush integer 6/7 current HTTP push server connection numbers VALUE SECURITY Group: di_i<0~(ndi-1)> NAME DESCRIPTION (get/set) normalstate high, 1/1 low indicate whether open circuit or closed circuit r
user_i0_pass string [64] 6/6 Root’s password user_i<1~20>_pass string [64] 7/6 User’s password user_i0_privilege admin 6/7 Root’s privilege user_i<1~20>_ privilege viewer, 6/6 User’s privilege.
Subgroup of network: http NAME VALUE SECURITY DESCRIPTION (get/set) port 80, 1025 ~ 65535 6/6 HTTP port alternateport 1025~65535 6/6 Alternative HTTP port authmode basic, 1/6 HTTP authentication mode digest s0_accessname string[32] 1/6 Http server push access name for stream 1 s1_accessname string[32] 1/6 Http server push access name for stream 2 SECURITY DESCRIPTION Subgroup of network: rtsp NAME VALUE (get/set) port 554, 1025 ~ 65535 6/6 RTSP port authmode disable, 1/6 R
audioport 1025 ~ 65535 4/4 Multicast audio port ttl 1 ~ 255 4/4 Mutlicast time to live value Subgroup of network: rtp NAME VALUE SECURITY DESCRIPTION (get/set) videoport 1025 ~ 65535 6/6 video channel port for RTP audioport 1025 ~ 65535 6/6 audio channel port for RTP SECURITY DESCRIPTION Subgroup of network: pppoe NAME VALUE (get/set) user string[128] 6/6 PPPoE account user name pass password[64] 6/6 PPPoE account password VALUE SECURITY DESCRIPTION Group: ipfilter NAME (
whitebalance auto, 4/4 auto, auto white balance indoor, indoor, 3200K fluorescent, fluorescent, 5500K outdoor outdoor, > 5500K Group: videoin_c<0~(n-1)> for n channel products, m is stream number NAME VALUE SECURITY DESCRIPTION (get/set) color 0, 1 4/4 0 =>monochrome 1 => color flip 4/4 flip the image mirror 4/4 mirror the image ptzstatus 1/7 An 32-bits integer, each bit can be set separately as follows: Bit 0 => Support camera control function 0(no
640x480,, s<0~(m1)>_ratecontrolmode cbr, vbr 4/4 cbr, constant bitrate vbr, fix quality s<0~(m-1)>_quant 1, 2, 3, 4, 5 4/4 quality of video when choosing vbr in “ratecontrolmode”. 1 is worst quality and 5 is the best quality.
input linein linein => use line input, i.e.
mode settings. hue -5 ~ 5 4/4 Adjust hue of image according to mode settings. Group: motion_c<0~(n-1)> for n channel product NAME VALUE SECURITY DESCRIPTION (get/set) enable 4/4 enable motion detection win_i<0~2>_enable 4/4 enable motion window 1~3 win_i <0~2>_name string[14] 4/4 name of motion window 1~3 win_i <0~2>_left 0 ~ 320 4/4 Left coordinate of window position. win_i <0~2>_top 0 ~ 240 4/4 Top coordinate of window position.
Custom server using safe100 method _hostname string[128] 6/6 Your dynamic hostname. _username email string[64] 6/6 Your user or email to login ddns service provider _passwordk ey string[64] 6/6 Your password or key to login ddns service provider _servernam e string[128] 6/6 The server name for safe100.
importance of information. 0: LOG_EMERG 1: LOG_ALERT 2: LOG_CRIT 3: LOG_ERR 4: LOG_WARNING 5: LOG_NOTICE 6: LOG_INFO 7: LOG_DEBUG Group: privacymask_c<0~(n-1)> for n channel product NAME VALUE SECURITY DESCRIPTION (get/set) enable 4/4 Enable the privacy mask win_i<0~4>_enable 4/4 Enable the privacy mask window win_i<0~4>_name string[14] 4/4 The name of privacy mask window win_i<0~4>_left 0 ~ 320/352 4/4 Left coordinate of window position.
ndo 0, 0/7 number of digital output 0/7 number of audio input 0/7 number of audio output naudioin 0, naudioout 0, nvideoin 0/7 number of video input nmediastream 0/7 number of media stream per channel nvideosetting 0/7 number of video settings per channel naudiosetting 0/7 number of audio settings per channel nuart 0, 0/7 number of UART interface
2 => videoin_resolution 0/7 indicate whether to support acoustic echo cancellation audio_extmic 0/7 indicate whether to support external microphone input audio_linein 0
wireless_802dot11b 0/7 Indicate whether to support the wireless 802.11b+ wireless_802dot11g 0/7 Indicate whether to support the wireless 802.
mdwin 6/6 Indicate which motion detection windows detected. This field is required when trigger condition is “md”. One bit represents one window. The LSB indicates the 1st window. For example, to detect the 1st and 3rd windows, set mdwin as 5. inter 1~999 6/6 Interval of period snapshot in minute. This field is used when trigger condition is “seq”. weekday 6/6 Indicate which weekday is scheduled. One bit represents one weekday. The bit0 (LSB) indicates Saturday.
Group: server_i<0~4> PARAMETER VALUE SECURITY DESCRIPTION (get/set) name string[40] 6/6 The identification of this entry type email, 6/6 Indicate the server type. ftp, “email” is email server. http, “ftp” is ftp server. ns “http” is http server. “ns” is network storage. http_url string[128] 6/6 The url of http server to upload. http_username string[64] 6/6 The username to login in the server. http_passwd string[64] 6/6 The password of the user.
Group: media_i<0~4> PARAMETER VALUE SECURITY DESCRIPTION (get/set) name string[40] 6/6 The identification of this entry type snapshot, 6/6 The media type to send to the server or store by the server. 6/6 Indicate the source of media stream. systemlog videoclip snapshot_source 0 means the first stream. 1 means the second stream and etc. snapshot_prefix string[16] 6/6 Indicate the prefix of the filename.
enable 0, 1 6/6 To enable or disable this recoding. priority 0, 1, 2 6/6 Indicate the priority of this recoding. “0” indicates low priority. “1” indicates normal priority. “2” indicates high priority. source 6/6 Indicate the source of media stream. 0 means the first stream. 1 means the second stream and etc. weekday 6/6 Indicate which weekday is scheduled. One bit represents one weekday. The bit0 (LSB) indicates Saturday. The bit1 indicates Friday.
Syntax: http:///cgi-bin/dido/setdo.cgi?do1=[&do2=] [&do3=][&do4=][&return=] Where state is 0, 1. “0” means inactive or normal state while “1” means active or triggered state. PARAMETER VALUE DESCRIPTION do 0, 1 0 – inactive, normal state 1 – active, triggered state return Redirect to the page after the parameter is assigned. The can be a full URL path or relative path according the the current path.
[di0=]\r\n [di1=]\r\n [di2=]\r\n [di3=]\r\n where can be 0 or 1. Example: Query the status of digital input 1 Request: http://myserver/cgi-bin/dido/getdi.cgi?di1 Response: HTTP/1.0 200 OK\r\n Content-Type: text/plain\r\n Content-Length: 7\r\n \r\n di1=1\r\n Query status of the digital output Note: This request requires the privilege of viewer. Method: GET/POST Syntax: http:///cgi-bin/dido/getdo.
[do0=]\r\n [do1=]\r\n [do2=]\r\n [do3=]\r\n where can be 0 or 1. Example: Query the status of digital output 1 Request: http://myserver/cgi-bin/dido/getdo.cgi?do1 Response: HTTP/1.0 200 OK\r\n Content-Type: text/plain\r\n Content-Length: 7\r\n \r\n do1=1\r\n Capture single snapshot Note: This request require normal user privilege Method: GET/POST Syntax: http:///cgi-bin/viewer/video.
quality 1~5 3 The quality of image Server will return the most up-to-date snapshot of selected channel and stream in JPEG format. The size and quality of image will be set according to the video settings on the server. Return: HTTP/1.0 200 OK\r\n Content-Type: image/jpeg\r\n [Content-Length: \r\n] Account management Note: This request requires administrator privilege Method: GET/POST Syntax: http:///cgi-bin/admin/editaccount.
privilege return The privilege of user to add or to modify. viewer viewer’s privilege operator operator’s privilege admin administrator’s privilege Redirect to the page after the parameter is assigned. The can be a full URL path or relative path according the the current path. If you omit this parameter, it will redirect to an empty page.
Post data: fimage=[&return=]\r\n \r\n Server will accept the upload file named to be upgraded the firmware and return with if indicated. IP filtering Note: This request requires administrator access privilege Method: GET/POST Syntax: http:///cgi-bin/admin/ipfilter.
end The end IP address to add or to delete. index The start position to add or to delete. return Redirect to the page after the parameter is assigned. The can be a full URL path or relative path according the the current path. If you omit this parameter, it will redirect to an empty page.
D. Technical data Video Compression: MPEG-4 & MJPEG Max. Resolution: 640x480 Pixel Available resolutions: 640x480, 320x240, 176x144 Framerate: max. 25 fps Network 10/100 Mbps Ethernet, RJ-45 Protocols (among others): IPv4,TCP/IP, HTTP, UPnP, RTSP/RTP/RTCP, IGMP, SMTP, FTP, DHCP, NTP, DNS, DDNS, PPPoE W-LAN 802.11b/g (only TV7222/TV7223) Audio GSM-AMR, Bit rate: 4.
E. Licence information GNU GPL We point at the fact that thenetwork cameras TV7220, TV7221, TV7222 and TV7223 among other things include Linux software source codes that are licensed under the GNU General Public Licence (GPL). To assure a GPL compliant usage of the used source codes we point at the licence terms of GPL. Licence text The licence text of the GNU General Public Licence can be found on the included software CD or on the ABUS Security-Center Homepage under http://www.abus-sc.
F. License MPEG-4 AAC Technology THIS PRODUCT IS LICENSED UNDER THE MPEG-4 AAC AUDIO PATENT LICENSE. THIS PRODUCT MAY NOT BE DECOMPILED, REVERSE-ENGINEERED OR COPIED, EXCEPT REGARD TO PC SOFTWARE, YOU MAY MAKE SINGLE COPIES FOR ARCHIVAL PURPOSES. FOR MORE INFORMATION, PLEASE REFER TO HTTP://WWW.VIALICENSING.COM.
